Ultra-precision grinding of optical glasses using mono-layer nickel electroplated coarse-grained diamond wheels. Part 2: Investigation of profile and surface grinding

After finishing the precision conditioning of mono-layer nickel electroplated coarse-grained diamond wheels with 151 μm (D151), 91 μm (D91) and 46 μm (D46) grain size, resp., profile and surface grinding experiments were carried out on a five-axis ultra-precision grinding machine with BK7, SF6 optical glasses and Zerodur glass ceramic. A piezoelectric dynamometer was used to measure the grinding forces, while an atomic force microscopy (AFM), white-light interferometer (WLI)) and scanning electron microscope (SEM) were used to characterize the ground surface quality in terms of micro-topography and subsurface damage. Moreover, the wear mechanics of the coarse-grained diamond wheels were analyzed and the grinding ratio was determined as well, in aiming to evaluate the grinding performance with the conditioned coarse-grained diamond wheels. Finally, the grinding results were compared with that of the fine-grained diamond wheels with regard to the ground specimen surface quality, process forces and wheel wear as a function of stock removal. The experimental results show that the precision conditioned coarse-grained diamond wheels can be applied in ductile mode grinding of optical glasses with high material removal rates, low wheel wear rates and no dressing requirement yielding excellent surface finishes with surface roughness in the nanometer range and subsurface damage in the micrometer range, demonstrating the feasibility and applicability of the newly developed diamond grinding technique for optical glasses.     

Study on methods to optimize laser-sharpening quality,efficiency and topography

This paper aims to improve bond surface smoothness, sharpening quality and efficiency as well as control grain protrusion height. Systematic research was performed on pulsed fiber laser sharpening of a coarse-grained bronze-bonded diamond grinding wheel. The results show that bond surface smoothness is related to the laser spot overlap ratio U_c and the laser scan track overlap ratio U_l. In the range 10–70%, an increase in U_c and U_l improved the sharpened bond surface smoothness. Sharpening quality and efficiency are both related to laser power density I_p. In the range 2.115–6.344 × 10⁷ W cm⁻², an increase in I_p gradually improved sharpening efficiency, but the sharpening quality trend initially improved followed by a subsequent decline. The grain protrusion height is related to the laser scan cycles N. An excessively small N will result in an insufficient chip space such that the grinding wheel is likely blocked. Grains will likely fall off due to an insufficient holding force if N is excessively large. Compared with silicon carbide grinding wheel sharpening, a pulsed laser-sharpened grinding wheel exhibits less surface grain fall-off, better grain height uniformity, more chip space around the grain and superior grinding wheel surface topography.     

ROTARY TRUING OF VITREOUS BOND DIAMOND GRINDING WHEELS USING METAL BOND DIAMOND DISKS

Experiments on rotary truing of vitreous bond diamond grinding wheels were conducted to investigate the effects of truing speed ratio, type of diamond in the metal bond truing disks (synthetic versus natural), and diamond grit size in the grinding wheel on the wear of truing disk and on the cylindrical grinding of zirconia. Similar to G-ratio, a new parameter called D-ratio is defined to quantify the wear rate of the diamond truing disks. Experimental results show that, under the same truing condition, the truing disk with blocky, low friability synthetic diamond has a higher D-ratio than the truing disk with natural diamond. Diamond wheels trued by the disk with synthetic diamond also generate lower grinding force and rougher surface finish. High truing disk surface speed, 1.8 times higher than the surface speed of the grinding wheel, was tested and did not show any improvement in D-ratio. This study indicates that μm-scale precision form truing of the vitreous bond diamond wheel is difficult due to excess wear of the metal bond diamond truing disk.     

ROTARY TRUING OF VITREOUS BOND DIAMOND GRINDING WHEELS USING METAL BOND DIAMOND DISKS

Abstract

Experiments on rotary truing of vitreous bond diamond grinding wheels were conducted to investigate the effects of truing speed ratio, type of diamond in the metal bond truing disks (synthetic versus natural), and diamond grit size in the grinding wheel on the wear of truing disk and on the cylindrical grinding of zirconia. Similar to G-ratio, a new parameter called D-ratio is defined to quantify the wear rate of the diamond truing disks. Experimental results show that, under the same truing condition, the truing disk with blocky, low friability synthetic diamond has a higher D-ratio than the truing disk with natural diamond. Diamond wheels trued by the disk with synthetic diamond also generate lower grinding force and rougher surface finish. High truing disk surface speed, 1.8 times higher than the surface speed of the grinding wheel, was tested and did not show any improvement in D-ratio. This study indicates that μm-scale precision form truing of the vitreous bond diamond wheel is difficult due to excess wear of the metal bond diamond truing disk.     

树脂基圆弧金刚石砂轮的在位精密成形修整技术

针对球面、非球面及自由曲面超精密磨削加工用树脂基圆弧形金刚石砂轮难以精密修整的问题,提出基于旋转绿碳化硅(GC)磨棒的在位精密成形修整技术。在分析GC磨棒和圆弧砂轮几何关系的基础上,确定修整过程中圆弧插补轨迹的补偿方法及GC磨棒运动轨迹的设计方案。采用KEYENCE激光测微仪采集砂轮圆弧特征点,表征圆弧砂轮的修整状况。研究不同粒度的GC磨棒、进给深度和圆弧插补速度对圆弧金刚石砂轮修整率和修整精度的影响规律。研究结果表明,该修整方法可根据加工曲率半径要求实现不同圆弧半径砂轮的精密在位修整,修整后可自动消除砂轮垂直方向的位置偏差;采用400#和800#的GC磨棒对D3和D7砂轮均有较高的修整率(0.7~6.7);与400#和1500#的GC磨棒相比,800#GC磨棒更适合粒度为D3和D7圆弧金刚石砂轮的精密修整;相比圆弧插补速度,进给深度对砂轮的圆弧半径尺寸误差和形状误差影响更大,进给深度越小,圆弧半径尺寸误差和形状误差越小;修整后两种砂轮的圆弧半径误差均可控制在5%以内,D3砂轮的形状误差可控制在3μm/4 mm以内,D7金刚石砂轮可控制在6μm/4 mm以内,修整后比修整前形状误差提高14倍左右。     

Wear of the blade diamond tools in truing vitreous bond grinding wheels: Part II. Truing and grinding forces and wear mechanism

Truing and grinding forces and the wear mechanism of particle and rod diamond blade tools used to generate precise and intricate forms on rotating vitreous bond silicon carbide grinding wheels are presented. A Hall effect sensor was used to measure the change of grinding spindle power during truing and grinding. A signal processing procedure was developed to identify individual truing passes and to extract the average, peak-to-valley, and standard deviation of the variation of truing force for each pass. The truing force data and SEM micrographs of worn surfaces on blade tools reveal micro- and macro-fracturing of the diamond. The attritious and erosion wear of the diamond rod and particle, erosion of the metal bond, and pulling-out of the diamond particle are also identified. Grinding force data shows that, for the same truing parameters, a wheel trued by the rod diamond blade tool has higher grinding forces than one trued by a particle diamond blade tool.     

金刚石砂轮中磨粒出刃的分形分析

针对金刚石砂轮微观出刃形貌复杂的问题,提出分形维数和等价出刃尺寸的评价指标。目的是利用分形维数和等价出刃尺寸分别评价砂轮磨粒的破碎程度和砂轮磨粒出刃的均匀程度。试验和分析结果表明,进给深度越大,砂轮出刃的分形维数就越大,表明砂轮磨粒的破碎程度越大,会给加工表面造成较大的粗糙度或划伤表面。进给深度对磨粒出刃的等价出刃尺寸的影响不大。     

Experimental study on fabrication and evaluation of micro pyramid-structured silicon surface using a V-tip of diamond grinding wheel

A mechanical fabrication of micro pyramid-structured silicon surface is proposed using crossed grooving with a 60° V-tip of diamond grinding wheel. It can obtain high form-accuracy, good surface quality and efficient productivity in contrast to laser machining and etching, and also assure a high aspect ratio in contrast to other mechanical processes. In order to describe its micro-structured topography, a white-light interferometer was employed, and its measured point cloud was matched using an Iterative Closest Point (ICP) algorithm. In micro grinding, a novel CNC mutual-wear truing was first developed to sharpen the wheel V-tip; then, the effects of microscopic wheel topography, silicon crystal-orientation and grinding parameter were investigated on ground micro-topography, truing ratio and material removal ratio; finally, its form-accuracy, pyramid top radius, groove tip radius, surface roughness and aspect ratio were evaluated. It is shown that better microscopic grain protrusion topography on wheel V-tip produces much larger material removal ratio and much better micro-structured topography in micro grinding, but it leads to much less truing ratio in finer GC truing. In micro grinding, silicon crystal-orientation has little effect on micro-structured topography due to diamond crystal-orientations that are randomly distributed on wheel V-tip. Although the micro pyramid-structured form error is only about 3.4 μm, its V-groove bottom and pyramidal top have very large form errors (23.1-47.9 μm) due to the sharpness of wheel V-tip and the frangibility of micro pyramid top. On increasing feed speed, its pyramid top radius decreases and its groove tip radius slightly increases, ultimately leading to an increase in aspect ratio, whereas its surface quality descends. It is concluded that the micro-pyramid arrays may be precisely patterned on silicon surface using a SD600 wheel with crossed tool paths, on-machine V-tip truing and the depth of cut in 1 μm.     

Wear of the blade diamond tools in truing vitreous bond grinding wheels: Part I. Wear measurement and results

The wear of stationary blade diamond tools used to generate a precise and intricate form on the vitreous bond grinding wheel is presented. Two types of blade tools made of rod and particle diamond were used. A method to measure the wear of the blade diamond tool in the μm-scale range using the size difference of two parts ground before and after truing was introduced. Two sets of experiments with four truing feeds and four tool traverse speeds across the grinding wheel were conducted on the rod and particle blade diamond tools, respectively. Experimental results showed the wear rate of blade diamond tools was improved at higher truing feeds and traverse speeds due to the brittle fracture of the abrasive and vitreous bond.     

Design and validation of a grinding wheel optical scanner system to repeatedly measure and characterize wheel surface topography

This paper describes the design and validation of an upgraded grinding wheel scanner system that controls the position of a Nanovea CHR-150 Axial Chromatism sensor along the x- and y-directions of the wheel surface to measure and characterize wheel surface topography. The scanner features a novel homing system that enables the wheel to be removed from the scanner, used on a grinding machine and then re-mounted and re-homed so that the same location on the wheel surface can be repeatedly measured and monitored. The average standard deviation for homing was 27.6 μm and 19.3 μm in the x- and y-directions, respectively, which is more than adequate for typical area scans of 25 mm². After homing, the scanner was able to repeatedly measure features that were similar in size to an abrasive grain (∼200 μm diameter) with an average error of 9.3 μm and 5.9 μm in the x- and y-directions, respectively. The resulting topography measurements were compared with Scanning Electron Microscope images to demonstrate the accuracy of the scanner. A custom particle filter was developed to process the resulting data and a novel analysis technique involving the rate of change of measured area was proposed as a method for establishing the reference wheel surface from which desired wheel topography results can be reported such as the number of cutting edges, cutting edge width and cutting edge area as a function of radial depth.     

单层钎焊金刚石砂轮的精密修整及效果评价

单层钎焊金刚石砂轮作为一种新型的磨削工具,具有磨粒固结强度高、磨粒出露大、容屑空间大等优点,比较适合高效率大切深的强力磨削,然而这种工具对高性能的脆性材料的精密磨削却比较困难。本文通过两种精密的修整工艺,使得加工表面质量大大提高。通过观察砂轮磨粒形态的变化可知,磨粒在修整过程中存在有磨损钝化、破碎、表面粘附等现象;通过对砂轮轮廓的激光测量可知,砂轮的磨粒等高性在修整过程中是明显改善的。通过修整磨粒粒径300μm的钎焊砂轮磨削氧化锆的表面粗糙度达到了Ra0.2μm。     

Cutting forces,tool wear and surface finish in high speed diamond machining

We have investigated the cutting forces, the tool wear and the surface finish obtained in high speed diamond turning and milling of OFHC copper, brass CuZn39Pb3, aluminum AlMg5, and electroless nickel. In face turning experiments with constant material removal rate the cutting forces were recorded as a function of cutting speed between v_c = 150 m/min and 4500 m/min revealing a transition to adiabatic shearing which is supported by FEM simulations of the cutting process. Fly-cutting experiments carried out at low (v_c = 380 m/min) and at high cutting speed (v_c = 3800 m/min) showed that the rate of abrasive wear of the cutting edge is significantly higher at ordinary cutting speed than at high cutting speed in contrast to the experience made in conventional machining. Furthermore, it was found that the rate of chemically induced tool wear in diamond milling of steel is decreasing with decreasing tool engagement time per revolution. High speed diamond machining may also yield an improved surface roughness which was confirmed by comparing the step heights at grain boundaries obtained in diamond milling of OFHC copper and brass CuZn39Pb3 at low (v_c = 100 m/min) and high cutting speed (v_c = 2000 m/min). Thus, high speed diamond machining offers several advantages, let alone a major reduction of machining time.     

基于气中放电辅助修整金刚石砂轮的试验研究

提出了一种新型的基于气中放电辅助金刚石砂轮在线修整法,它把气中火花放电修整法和金刚石笔机械修整法有机结合在一起,能实现光学曲线磨床上金刚石砂轮的高效、高精度、低成本和不得使用任何冷却液的在线修整。采用自制的试验装置在MK9025数控光学曲线磨床上对1A1／T2 200×6×32×4 MBD6 120／140 M75型号的砂轮进行了在线修整试验,得出了一些影响金刚笔磨损率的主要因素:火花放电时热源的能量分布状况、金刚石笔修整时的修整深度、进给量以及电源电压。相同工况下机械修整法和气中放电辅助修整法中金刚石笔的磨损率对比试验结果表明:气中放电辅助修整和机械修整有着不同的材料去除机理,它比一般机械修整更有利于提高金刚石砂轮的修整效率和降低金刚石笔的磨损量。磨削YG8硬质合金工件的试验表明,采用气中放电辅助法修整的金刚石砂轮和新的金刚石砂轮有着相近的磨削能力。     

Surface finishing: Impact on tribological characteristics of WC–Co hardmetals

Flat samples of WC–Co hardmetals with 6–12 wt%Co were surface finished by grinding, polishing and wire-electro-discharge machining (EDM). Comparative dry reciprocating sliding experiments against WC–6 wt%Co pins were performed using a Plint TE77 tribometer. Tribological characteristics were recorded online. Wear surfaces were characterized by surface scanning topography and scanning electron microscopy. Wire-EDM’ed samples exhibited higher friction and wear compared to ground and polished equivalents. This trend was correlated to X-ray diffraction measurements revealing tensile residual surface stresses in WC after wire-EDM contrary to compressive surface stresses after grinding and polishing. However, finer executed EDM reduces friction and wear significantly.     

IN SITU TRUING/DRESSING OF DIAMOND WHEEL FOR PRECISION GRINDING

An application for achieving on-machine truing/dressing and monitoring of diamond wheel is dealt with in dry grinding. A dry electrical discharge （ED） assisted truing and dressing method is adopted in preparation of diamond grinding wheels. Effective and precise truing/dressing of a diamond wheel is carried out on a CNC curve grinding machine by utilizing an ED assisted diamond dresser. The dressed wheel is monitored online by a CCD vision system. It detects the topography changes of a wheel surface. The wear condition is evaluated by analyzing the edge deviation of a wheel image. The benefits of the proposed methods are confirmed by the grinding experiments. The designed truing/dressing device has high material removal rate, low dresser wear, and hence guarantees a desired wheel surface. Real-time monitoring of the wheel profile facilitates determining the optimum dressing amount, dressing interval, and the compensation error.     

Wear behaviour of dental enamel at the nanoscale with a sharp and blunt indenter tip

Two different diamond nanoindenter tips, a rounded conical (～1200 nm radius) and a sharp cube corner (20–50 nm radius) were used to abrade bovine enamel. Square abraded areas (2 μm × 2 μm, 5 μm × 5 μm, 10 μm × 10 μm) were generated with loads that varied from 50 μN to 500 μN depending on the indenter tip. In addition normal and lateral forces were simultaneously measured along 10 μm single scratched lines with the sharp cube corner tip. SEM (scanning electron microscopy) and TEM (transmission electron microscopy) were also used to characterise the worn areas and debris. Two different wear mechanisms were observed depending on the geometry of the tip. The rounded tip generates a predominantly elastic contact that mainly compresses and plastically deforms the superficial material and generates severe shear deformation within the sub-surface material which, under certain conditions, fractures and removes material from the sample. The sharp tip cuts into and ploughs the enamel creating a wedge or ridge of material ahead of itself which eventually detaches. This sequence is repeated continuously for every passage of the sharp indenter tip. The different mechanisms are discussed in terms of abrading tip contact angle and enamel microstructure.     

光纤石英玻璃基板微V槽阵列的精密磨削

针对脆性石英玻璃的微加工,利用自主研发的金刚石砂轮微尖端修整工艺,研发了光纤阵列石英玻璃微V槽磨削技术。分析了60°的微V槽形状偏差对光纤耦合损耗的影响,然后,研究了砂轮微尖端的误差补偿修整工艺。最后,实验分析了微V槽的磨削精度。理论分析显示:微V槽角度、间距和宽度的偏差分别控制在±0.42°、±1.04μm和±1.2μm以内时,耦合损耗小于0.5dB。实验结果表明:开发的数控磨削工艺可加工高精度的60°微V槽阵列;采用数控轨迹和角度补偿修整后,砂轮微尖端半径可平均达到10.46μm,角度精度为(60±0.22)°;对石英玻璃进行微磨削后,微V槽的角度偏差达到0.4°,尖端半径为10.5μm,宽度偏差为0.3μm,间距偏差为0.5μm,可保证光纤阵列的精密对接。     

铸铁基金刚石球头砂轮精密修整技术

针对小直径、深凹非球光学曲面超精密磨削中使用的铸铁基金刚石球头砂轮,提出了一种基于电火花加工原理的精密在位修整方法。只要改变工具电极直径,即可对不同直径的球头砂轮进行修整。实验表明,用该方法修整出的铸铁基金刚石球头砂轮具有良好的精度和高等微刃群,可很好地满足小直径、深凹光学零件的超精密磨削加工要求。     

电镀金刚石砂轮高效精密修整及熔融石英磨削试验研究

大尺寸光学玻璃元件主要采用细磨粒金刚石砂轮进行精密/超精密磨削加工,但存在砂轮修整频繁、工件表面面形精度难以保证、加工效率低等缺点。采用大磨粒金刚石砂轮进行加工则具有磨削比大、工件面形精度高等优点,然而高效精密的修整是其实现精密磨削的关键技术。采用Cr12钢对电镀金刚石砂轮(磨粒粒径151 μm)进行粗修整,借助修整区域聚集的热量加快金刚石的磨损,可使砂轮的回转误差快速降至10 μm以内。结合在线电解修锐技术,采用杯形金刚石修整滚轮对粗修整后的电镀砂轮进行精修整,砂轮的回转误差可达6 μm以内,轴向梯度误差由6 μm降至2.5 μm。通过对修整前后的金刚石砂轮表面磨损形貌成像及其拉曼光谱曲线分析了修整的机理。对应于不同的砂轮修整阶段进行熔融石英光学玻璃磨削试验,结果表明,砂轮回转误差较大时,工件材料表面以脆性断裂去除为主;随着砂轮回转误差和轴向梯度误差的减小,工件表面材料以塑性去除为主,磨削表面粗糙度为Ra19.6 nm,亚表层损伤深度低至2 μm。可见,经过精密修整的大磨粒电镀金刚石砂轮可以实现对光学玻璃的精密磨削。     

SYSTEMS APPROACH FOR THE CERAMIC THRU-FEED CENTERLESS GRINDING

An approach for simulation and production implementation of thru-feed centerless grinding of transformation toughened zirconia using vitreous bond diamond grinding wheels is presented. A set of grinding tests was designed and conducted to identify the effects of abrasive product (diamond grit size), work-material, and operational factors (stock removal, thru-feed rate, number of thru-feed passes and truing and dressing methods) on grinding performance. Evaluation parameters of surface finish, grinding forces and C-ratio were utilized to determine machine tool features. Very fine surface finishes, in the order of 0.05 to 0.1 u.m R_a range, could be achieved using vitreous bond micro-grit diamond wheels, without additional part processing. Such a level of surface finish on ground ceramics has traditionally been generated only by using resinoid bonded diamond wheels. These test results were used to design and manufacture a full-size composite or sandwiched diamond grinding wheel. This grinding wheel has been successfully applied in high-volume ceramic production, which in turn has verified the proposed approach. Lastly, the surface finish data is interpreted based on SEM and AFM observations and materials properties.