Adiabatic-CMOS/CMOS-adiabatic logic interface circuit

This paper describes the design of an adiabatic-CMOS/CMOS-adiabatic logic interface circuit for a group of low-power adiabatic logic families with a similar clocking scheme. The circuit provides interfacing between several recently proposed low-power adiabatic logic circuits and traditional digital CMOS circuits. One advantage of this design is that it is insensitive to clock overlap. With the proposed interface circuit, both adiabatic and CMOS logic circuits are able to co-exist on a single chip, taking advantage of the strengths of each approach in the design of low power systems.     

Design of a DTCTGAL circuit and its application

By research on the switch-signal theory for multiple-valued logic circuits, the theory of three essential elements and the principle of adiabatic circuits, a design scheme for a double power clock ternary clocked transmission gate adiabatic logic (DTCTGAL) circuit is presented. The energy injection and recovery can be conducted by the bootstrapped NMOSFET, which makes the circuit maintain the characteristics of energy recovery as well as multiple-valued input and output. An XOR/XNOR circuit based on DTCTGAL is also presented using this design scheme. Finally, using the parameters of a TSMC 0.25 μm CMOS device, PSPICE simulation results indicate that the proposed circuits have correct logic and significant low power characteristics.     

Performance analysis of a complete adiabatic logic system driven by the proposed power clock generator

We analyze the energy performance of a complete adiabatic circuit/system including the Power Clock Generator （PCG） at the 90 nm CMOS technology node. The energy performance in terms of the conversion efficiency of the PCG is extensively carried out under the variations of supply voltage, process comer and the driver transistor＇s width. We propose an energy-efficient singe cycle control circuit based on the two-stage comparator for the synchronous charge recovery sinusoidal power clock generator （PCG）. The proposed PCG is used to drive the 4-bit adiabatic Ripple Carry Adder （RCA） and their simulation results are compared with the adiabatic RCA driven by the reported PCG. We have also simulated the logically equivalent static CMOS RCA circuit to compare the energy saving of adiabatic and non-adiabatic logic circuits. In the clock frequency range from 25 MHz to 1GHz, the proposed PCG gives a maximum conversion efficiency of 56.48%. This research work shows how the design of an efficient PCG increases the energy saving of adiabatic logic.     

Four-phase power clock generator for adiabatic logic circuits

A circuit for a four-phase trapezoidal power clock generator for adiabatic logic circuits realised with a double-well 0.25 μm CMOS technology and external inductors is proposed. The circuit, at a frequency of 7 MHz which is within the optimum frequency range for adiabatic circuits realised with 0.25 μm CMOS technology, has a conversion efficiency higher than 80%, and is robust with respect to parameter variations     

QSERL: quasi-static energy recovery logic

A new quasi-static energy recovery logic family (QSERL) using the principle of adiabatic switching is proposed in this paper. Most of the previously proposed adiabatic logic styles are dynamic and require complex clocking schemes. The proposed QSERL uses two complementary sinusoidal supply clocks and resembles the behavior of static CMOS. Thus, switching activity is significantly lower than dynamic logic. In addition, QSERL circuits can be directly derived from static CMOS circuits. A high-efficiency clock generation circuitry, which generates two complementary sinusoidal clocks compatible to QSERL, is also presented in this paper. The adiabatic clock circuitry locks the frequency of clock signals, which makes it possible to integrate adiabatic modules into a VLSI system. We have designed an 8×8 carry-save multiplier using QSERL logic and two phase sinusoidal clocks. SPICE simulation shows that the QSERL multiplier can save 34% of energy over static CMOS multiplier at 100 MHz     

Design of ternary adiabatic multiplier on switch-level

The design of ternary adiabatic multiplier adopting switch-level design techniques is proposed in this paper. First by using the theory of three essential circuit elements, the switch-level functional expressions of the carry and product circuit models, which compose one bit ternary adiabatic multiplier, are derived. Consequently, the corresponding circuit structures can be obtained, and the evaluation and energy recovery for ternary circuit can be realized by bootstrapped NMOS transistors and cross-memory structure. Based on the designed circuits, the four bits ternary adiabatic multiplier is further realized by adopting the ripple carry manner. The PSPICE simulation results indicate that the designed circuits have correct logic function and are characterized with distinctive low power consumption.     

An efficient charge recovery logic circuit

Efficient charge recovery logic (ECRL) is proposed as a candidate for low-energy adiabatic logic circuit. Power comparison with other logic circuits is performed on an inverter chain and a carry lookahead adder (CLA). ECRL CLA is designed as a pipelined structure for obtaining the same throughput as a conventional static CMOS CLA. Proposed logic shows four to six times power reduction with a practical loading and operation frequency range. An inductor-based supply clock generation circuit is proposed. Circuits are designed using 1.0-μm CMOS technology with a reduced threshold voltage of 0.2 V     

一种利用自举效应的Charge-Recovery逻辑电路

提出了一种新的 semi- adiabatic逻辑电路—— Bootstrap Charge- Recovery Logic( BCRL) .该电路由 semi- adiabatic电路完成逻辑运算 ,而由自举的 NMOS管驱动负载 ,对负载的操作为 full- adiabatic过程 .BCRL电路由两相无交叠脉冲时钟电源供电 ,输出为全摆幅脉冲信号 .比较了 BCRL反相器驱动电容负载时与静态 CMOS电路及部分文献中的 semi- adiabatic电路的功耗差别 .应用 0 .65μm CMOS工艺器件参数的模拟结果表明 ,BCRL电路可以在1 0 0 MHz脉冲电源频率下正常工作 ,并且有较好的降低功耗的效果     

A 32×32-b adiabatic register file with supply clock generator

A 32×32-b adiabatic register file with one read port and one write port is designed. A four-phase clock generator is also designed to provide supply clocks for adiabatic circuits. All the word line and bit line charge on the capacitive interconnections is recovered to save energy. Adiabatic circuits are based on efficient charge recovery logic (ECRL) and are integrated using 0.8 μm complimentary metal-oxide-semiconductor (CMOS) technology. Measurement results show that power consumption of the core is significantly reduced by a factor of up to 3.5 compared with a conventional circuit     

能量回收阈值逻辑及其功率时钟产生电路

提出了能量回收阈值逻辑电路(ERTL).该电路把阈值逻辑应用到绝热电路中,降低能耗的同时也降低了电路的门复杂度.并且提出了一种高效率的功率时钟产生电路.该功率时钟电路能够根据逻辑的复杂度和工作频率,调整电路中MOS开关的开启时间,以取得最优的能量效率.为了便于功率时钟的优化设计,推导出了闭式结果.基于0.35μm的工艺参数,设计并且仿真了ERTL可编程逻辑阵列(PLA)和普通结构PLA.在20～100MHz的工作频率范围内,提出的功率时钟电路的能量效率可以达到77%～85%.仿真结果还显示,ERTL是一个低能耗的逻辑.ERTL PLA与普通结构的PLA相比,包括功率时钟电路的功耗在内,ERTL PLA仍节省65%～77%的功耗.     

BiCMOS circuit technology for a 704 MHz ATM switch LSI

This paper describes BiCMOS level-converter circuits and clock circuits that increase VLSI interface speed to 1 GHz, and their application to a 704 MHz ATM switch LSI. An LSI with a high speed interface requires a BiCMOS multiplexer/demultiplexer (MUX/DEMUX) on the chip to reduce internal operation speed. A MUX/DEMUX with minimum power dissipation and a minimum pattern area can be designed using the proposed converter circuits. The converter circuits, using weakly cross-coupled CMOS inverters and a voltage regulator circuit, can convert signal levels between LCML and positive CMOS at a speed of 500 MHz. Data synchronization in the high speed region is ensured by a new BiCMOS clock circuit consisting of a pure ECL path and retiming circuits. The clock circuit reduces the chip latency fluctuation of the clock signal and absorbs the delay difference between the ECL clock and data through the CMOS circuits. A rerouting-Banyan (RRB) ATM switch, employing both the proposed converter circuits and the clock circuits, has been fabricated with 0.5 μm BiCMOS technology. The LSI, composed of CMOS 15 K gate logic, 8 Kb RAM, I Kb FIFO and ECL 1.6 K gate logic, achieved an operation speed of 704-MHz with power dissipation of 7.2 W     

Superconducting digital electronics

Single-flux quantum logic (SFQ) circuits, in which a flux quantum is used as an information carrier, have the possibility for opening the door to a new digital system operated at over 100-GHz clock frequency at extremely low power dissipation. The SFQ logic system is a so-called pulse logic, which is completely different from the level logic for semiconductors like CMOS, so circuit design technologies for SFQ logic circuits have to be newly developed. Recently, much progress in basic technologies for designing SFQ circuits and operating circuits at high speeds has been made. With advances in these design tools, large-scale circuits including more than several thousand junctions can be easily operated with the clock frequency of more than several tens of gigahertz. High-end routers and high-end computers are possible applications of SFQ logic circuits because of their high throughput nature and the low power dissipation of SFQ logic. In this paper, recent advances of SFQ circuit design technologies and recent developments of switches for high-end routers and microprocessors for high-end computers that are considered possible applications for SFQ logic will be described.     

Precomputation-based sequential logic optimization for low power

We address the problem of optimizing logic-level sequential circuits for low power. We present a powerful sequential logic optimization method that is based on selectively precomputing the output logic values of the circuit one clock cycle before they are required, and using the precomputed values to reduce internal switching activity in the succeeding clock cycle. We present two different precomputation architectures which exploit this observation. The primary optimization step is the synthesis of the precomputation logic, which computes the output values for a subset of input conditions. If the output values can be precomputed, the original logic circuit can be “turned off” in the next clock cycle and will have substantially reduced switching activity. The size of the precomputation logic determines the power dissipation reduction, area increase and delay increase relative to the original circuit. Given a logic-level sequential circuit, we present an automatic method of synthesizing precomputation logic so as to achieve maximal reductions in power dissipation. We present experimental results on various sequential circuits. Up to 75% reductions in average switching activity and power dissipation are possible with marginal increases in circuit area and delay     

Skewed CMOS: noise-tolerant high-performance low-power static circuit family

In this paper, we present a noise-tolerant high-performance static circuit family suitable for low-voltage operation called skewed logic. Skewed logic circuits in comparison with Domino logic have better scalability and are more suitable for low voltage applications because of better noise margins. Skewed logic and its variations have been compared with Domino logic in terms of delay, power, and dynamic noise margin. A design methodology for skewed CMOS pipelined circuits has been developed. To demonstrate the applicability of the proposed logic style, 0.35 /spl mu/m 5.56 ns CMOS 16/spl times/16 bit multipliers have been designed using skewed logic circuits and fabricated through MOSIS. Measurement results show that the multiplier only consumed a power of 195 mW due to its low clock load.     

Clock Delayed Domino Logic With Efficient Variable Threshold Voltage Keeper

In this paper, efficient clock delayed domino logic with variable strength voltage keeper is proposed. The variable strength of the keeper is achieved through applying two different body biases to the keeper. The circuits used to generate the body biases are called capacitive body bias generator and cross-coupled capacitive body bias generator. Compared to a previous work, the body bias generator circuits presented in this paper are simpler and do not require double or triple power supply while consuming less area and power. To show the efficiency of the proposed technique, the implementation of a carry generator circuit by the proposed techniques and the previous work are compared. The simulation results for standard CMOS technologies of 0.18 mum and 70 nm show considerable improvements in terms of power and power delay product. In addition, the proposed technique shows much less temperature dependence when compared to that of previous work     

A fault detection sensor for circuit aging using double-edge-triggered flip-flop

In nanoscale technology, transistor aging is one of the most critical problems that impact on the reliability of circuits. Aging sensor is a good online way to detect the circuit aging, which performs during the operating time with no influence of the normal operation of circuits. In this paper, a Double-edge-triggered Detection Sensor for circuit Aging (DSDA) is proposed, which employs data signal of logic circuits as its clock to control the sampling process. The simulation is done by Hspice using 45 nm technology. The results show that this technique is not sensitive to the process variations. The worst case of the detection precision is more than 80% under the different process variations. It can detect aging fault effectively with the 8% power cost and 30% performance cost.     

Design and performance of multistage GaAs dynamic logic

GaAs Two-Phase Dynamic FET Logic (TDFL) circuits are capable of extremely low power dissipation (20 nW/MHz/gate), high speed (1 GHz), and are compatible with static GaAs logic families. This paper demonstrates that TDFL can be modified to execute two or three stages of logic in one clock phase. This extension provides extremely high functional complexity per gate that can be used to reduce power dissipation, reduce latency, and increase circuit density in both sequential and computationally-oriented applications. The performance of these gates was demonstrated by E/D MESFET IC test circuits fabricated by a digital IC foundry. A one clock cycle, 8-b carry-lookahead adder operated at 350 MHz with only 1.1 mW of power dissipation     

一种用于DSCRL绝热电路的新型功率时钟

提出了一种用于DSCRL(双摆幅电荷恢复逻辑)绝热电路的新型四相功率时钟,该功率时钟采用了非对称的方法来优化其时序,比已提出的采用对称技术来优化时序的六相功率时钟更简洁.这种新型的功率时钟用于DSCRL绝热电路后,该电路仍然保持了其能量恢复的高效性,同时还降低了电路设计的复杂性,这一结论已被文中的HSPICE 模拟结果证明.     

一种用于DSCRL绝热电路的新型功率时钟

提出了一种用于DSCRL(双摆幅电荷恢复逻辑)绝热电路的新型四相功率时钟,该功率时钟采用了非对称的方法来优化其时序,比已提出的采用对称技术来优化时序的六相功率时钟更简洁.这种新型的功率时钟用于DSCRL绝热电路后,该电路仍然保持了其能量恢复的高效性,同时还降低了电路设计的复杂性,这一结论已被文中的HSPICE 模拟结果证明.     

采用交流能源的低功耗CPL电路

从改变CM O S电路中能量转换模式的观点出发,研究CPL电路在采用交流能源后的低功耗特性。在此基础上提出了一种仅由nM O S构成的低功耗绝热电路——nM O S Com p lem en tary Pass-trans istor A d iabaticLog ic(nCPAL)。该电路利用nM O S管自举原理对负载进行全绝热驱动,从而减小了电路整体功耗和芯片面积。nCPAL能耗几乎与工作频率无关,对负载的敏感程度也较低。采用TSM C的0.25μm CM O S工艺,设计了一个8-b it超前进位加法器和功率时钟产生器。版图后仿真表明,在50~200 MH z频率范围内,nCPAL全加器的功耗仅为PAL-2N电路和2N-2N 2P电路的50%和35%。研究表明nCAPL适合于在VLS I设计中对功率要求较高的应用场合。