Study on the new control scheme of class-E inverter for IH-jar application with clamped voltage characteristics using pulse frequency modulation

A new control scheme of Class-E inverter for induction heating jar applications with clamped voltage characteristics using pulse frequency modulation (PFM) is introduced. To reduce the voltage stress of a switch, the proposed PFM control scheme does not need any auxiliary circuit. It can decrease the voltage stress of a switch through the modulation of switching frequency. The Class-E inverter using the proposed control scheme has the advantages of not only the same output power when it is compared with an active clamped class-E (ACCE) inverter, but also zero-voltage-switching, which are characteristics of conventional Class-E and ACCE inverter. The control principles of the proposed method are explained in detail and its validity is verified through experimental results     

Design and implementation of FPGA-based phase modulation control for series resonant inverters

Owing to the tremendous advances in the digital technology, and improved reliability and performance of the digital control mechanisms, this paper focuses on design and implementation of digital controller using FPGA-based circuit design approach. The digital controller proposed is designed for series resonant inverter used in DC-DC converter applications. Phase modulation technique is proposed for the realization of digital controller on FPGA. The Series Resonant Converter (SRC) is considered in this paper as a preferred converter topology for high power, high voltage power supplies. This paper studies the implementation of phase shift modulation technique using FPGA. The inverter designed, is IGBT based, and Zero Voltage Switching (ZVS) technique is implemented due to reduced stresses on devices and increased efficiency. The phase modulated series resonant inverters (PM-SRC) promotes ZVS operation when its switching frequency is greater than resonant frequency. The designed PM controller is realized using FPGA on which control algorithm and other features of a controller are developed. The series resonant inverter is built and tested for full load under open loop and closed loop conditions at a switching frequency of 20 kHz. The results are presented under varying load conditions. The simulation and the experimental results were found to match closely.     

A commutation strategy for IGBT-based CSI-fed parallel resonant circuit for induction heating application

A brief study on a commutation strategy for a current source inverter (CSI)-fed parallel resonant circuit, using switches formed by IGBTs with series diodes, is presented in this paper. The dynamic behaviour of the inverter and different strategies for its reliable operation are discussed here considering parasitic inductance and overlap time between CSI switching devices. The dynamic behaviour of the switches decides the upper frequency limit for the application. IGBTs with the series diodes behave as uni-directional current switches with bi-directional voltage blocking capability. This feature should be taken into account to decide on an appropriate switching strategy for this converter configuration.     

Performance of burst-mode receivers for optical digital pulse position modulation in passive optical network application

A DC coupled burst-mode receiver for digital pulse position modulation (DPPM) is proposed for the first time. An analysis of the potential performance benefits of using such a receiver configuration in the upstream of a passive optical network is given. An optical pre-amplifier is assumed. Bit error rate expressions are derived and the performance is evaluated in terms of sensitivity and threshold acquisition penalty. Results are compared with a DC-coupled on?off keyed non-return-to-zero burst-mode receiver, and it is seen that DPPM?s continuous mode sensitivity advantage (about 8 dB for the optimal case) is only reduced to 7.7 dB when overhead preamble is restricted to 12 bits and 6 dB when restricted to 6 bits. Thus, if necessary, DPPM can almost recover its sensitivity advantage by a trade off with preamble length. As such DPPM can potentially offer an increase in optical network unit numbers by a factor of 4 or, alternatively, an increase in range of around 20 km.     

集成锁相环在激光脉冲调制系统中的应用

锁相环由鉴相器、环路滤波器及压控震荡晶体组成,是一个能跟踪输入信号频率和相位的闭环自动控制系统。研制的激光脉冲调制系统采用锁相技术,以单片、集成锁相环代替分立元件,实现了片内鉴频和鉴相的功能。研制的腔倒空驱动器能够输出 4MHz, 800kHz, 400kHz, 80kHz,40kHz, 8kHz, 4kHz, 800Hz, 400Hz 等不同重复频率的脉冲信号,输出功率达到瓦级,满足了声光布拉格池的要求。该激光脉冲调制系统已经应用在皮秒时间相关单光子计数光谱仪系统中,取得了比较理想的效果。     

A microwave zero radiometer with combined pulse modulation

A microwave radiation radiometer is described which uses a modification of the zero-reception method. Two input units are developed which enable the antenna signals in different ranges of variation to be measured, and their fluctuation sensitivity is analyzed. __________ Translated from Izmeritel’naya Tekhnika, No. 3, pp. 65–69, March, 2007.     

Optimized pulse width modulation pattern strategy for three-dimensional profilometry with projector defocusing

Three-dimensional profilometry by sinusoidal fringe projection using phase-shifting algorithms is usually distorted by the nonlinear intensity response of commercial video projectors. To overcome this problem, several methods including sinusoidal pulse width modulation (SPWM) were proposed to generate sinusoidal fringe patterns with binary ones by defocusing the project to some certain extent. However, the residual errors are usually nonnegligible for highly accurate measurement fields, especially when the defocusing level is insufficient. In this work, we propose two novel methods to further improve the defocusing technique. We find that by properly optimizing SPWM patterns according to some criteria, and combining SPWM technique with four-step phase-shifting algorithm, the dominant undesired harmonics will have no impact on the phase obtained. We also propose a new sinusoidal fringe generation technique called tripolar SPWM, which can generate ideal sinusoidal fringe patterns with a very small degree of defocusing. Simulations and experiments are presented to verify the performance of these two proposed techniques.     

Simple resistance calculation in litz-wire planar windings for induction cooking appliances

We present a simple method to calculate the winding resistance of a litz-wire inductor in an induction cooking appliance, taking into account eddy-current losses, including conduction losses and proximity-effect losses. The method, which uses numerical calculation of the magnetic field, can be used to determine the optimum number of strands in the litz wire. The effects of the temperature on the winding total resistance are included in the calculation. We have built a prototype to verify the calculation method and its limitations. We consider the accuracy limits of the method.     

Three-phase soft-switched pwm inverter for motor drive application

A novel soft-switched inverter topology in which three mutually coupled inductors at a time are involved in the resonance process is proposed. By the introduction of magnetic coupling between three resonant inductors, the zero-voltage instants for the inverter can be generated by one auxiliary switch. Also, the resonant energy can be recycled, and the maximum voltage stress on the auxiliary circuit diode components is confined to the DC-link clamp voltage level. The DC link can be clamped to 1.1-1.3 times the DC-source value. This is unlike the soft-switched inverter in which two mutually coupled inductors are at a time are involved in a resonance process, wherein the clamping diode experiences voltage stress of the order of 11 per unit when clamping the DC-link voltage at 1.1 per unit. The proposed inverter also provides pulse-width modulated operation. An analysis of this novel quasi-resonant DC-link inverter topology is presented to reveal its soft-switching characteristics. Simulation and laboratory experiments are performed to validate the analysis.     

Comparison of the squared binary, sinusoidal pulse width modulation, and optimal pulse width modulation methods for three-dimensional shape measurement with projector defocusing

This paper presents a comparative study on three sinusoidal fringe pattern generation techniques with projector defocusing: the squared binary defocusing method (SBM), the sinusoidal pulse width modulation (SPWM) technique, and the optimal pulse width modulation (OPWM) technique. Because the phase error will directly affect the measurement accuracy, the comparisons are all performed in the phase domain. We found that the OPWM almost always performs the best, and SPWM outperforms SBM to a great extent, while these three methods generate similar results under certain conditions. We will briefly explain the principle of each technique, describe the optimization procedures for each technique, and finally compare their performances through simulations and experiments.     

Interaction of an optically dense bose condensate with a resonant laser pulse

Propagation of a resonant laser pulse through an optically dense Bose-Einstein condensate is theoretically investigated. Changes in the spatial distribution of the condensate after the laser pulse propagation are analyzed. It is shown that atoms escape from the condensate due to the joint action of two factors: the transition of atoms from the ground state to an excited state upon absorption of the resonant photons and the effect of a zero-result measurement. The latter effect is interpreted in terms of the theory of quantum measurements.     

等离子清洗用谐振电源混合调制技术研究

针对现有等离子体放电电源及其控制系统低效率和高成本的缺点,该文以串联谐振型高频高压电源为研究对象,对不同的控制模式进行研究,提出基于PWM-PFM混合调制的功率跟踪控制策略。同时,对感性和容性两种控制模式进行对比,根据IGBT的关断特点和工作频率,提出高功率欠谐振和低功率过谐振的工作模式,解决等离子清洗用电源在高频率下功率因数低、开关损耗大的问题。实验结果表明:混合调制策略能够有效降低IGBT的损耗,使整机效率提高0.65%～5.51%;在相同工况下,将设备的调功范围从600～950 W提升到550～1 000 W,使得等离子清洗机的清洗对象更为丰富,更容易推广。     

Ultrafast optical pulse digitization with unary spectrally encoded cross-phase modulation

A method to digitize the intensity of ultrashort laser pulses for high-speed optical signal processing is described. This digitization was based on the spectral broadening of a weak probe (carrier) pulse by a more intense pump (signal) pulse through the nonlinear optical process of cross-phase modulation (XPM). The signal pulse intensity was varied to generate different spectral widths that can be encoded into digital form. Using a 50-ps time-divided multiplexing pulse train with a waveguide splitter, combiner, and an array of fibers with variable lengths, a unary XPM encoding approach is demonstrated. The spectral encoding scheme can be used to achieve a 5-GHz sampling rate at a 16-level accuracy.     

Channel estimation for time-hopping pulse position modulation ultra-wideband communication systems

Ultra-wideband (UWB) communication systems are used in indoor environments with dense multi-path characteristics. Therefore channel estimation has an important role in the receiver of these systems. A new approach for data-aided (DA) and non-data-aided (NDA) channel estimation is proposed, which is called the pulse compression (PC) method. This method is useful for UWB systems employing time-hopping pulse position modulation. The PC method requires only some basic operations such as sampling, overlap-add and finite impulse response filtering. The PC method, in both DA and NDA scenarios, in spite of its low complexity, outperforms the maximum-likelihood (ML) method in channel parameters estimation. The bit error rate (BER) of the DA method, in single-user scenario, performs as well as the ML method, and in multi-user scenario, in the worst case, there is only 0.5 dB loss compared with the ML method. In the case of NDA scenario, the proposed method outperforms the NDA-ML method, that is, in the single-user scenario about 4 dB gain at the BER of 1023 is observed. In multi-user scenario, it outperforms significantly the NDA-ML method, and its performance loss in comparison with the perfect channel knowledge scenario is about 3 dB at the BER of 1023.     

Selection of modulation code parameters for maximum lineal density

The relative performance capabilities for many known run-length-limited binary modulation codes useful in digital magnetic recording are placed in perspective. The criteria for grading is relative maximum achievable lineal recording density under conditions of quasi-optimal spectral shaping. The results are based upon a linear system analysis in which superposition is applicable in modeling saturation recording systems where the media is indeed fully saturated at the termination of each transition. The maximum relative achievable lineal density is shown in terms of code parameters for maximum theoretical information rate with run constraints. The results show which binary modulation code to select for maximal lineal density and how its performance compares with the maximum theoretically achievable for any binary modulation code.     

Approximate analytical expressions for pulse modulation response of quantum cascade lasers

Approximate analytical expressions for turn-on delay, rise time and fall time for pulse modulation of the drive current of quantum cascade lasers are presented. These time expressions are obtained using piece-wise analysis of rate equations. From the analytical expressions, the effects of laser parameters and off and on currents are discussed. A numerical analysis shows reasonable agreement with analytical results. It also confirms the predictions from analytical results. The pulse response is compared with that of near-infrared interband lasers.     

Pulse width modulation technique with harmonic injection and frequency modulated carrier: formulation and application to an induction motor

A new generated pulse width modulation (PWM) technique is presented, making it possible to significantly reduce harmonics in comparison to currently used PWMs operating in real time. This improvement means that a motor connected to an inverter that is controlled with this technique undergoes less overheating and vibrations, thereby improving its performance.     

M-ary pulse position modulation performance with adaptive optics corrections in atmospheric turbulence

ABSTRACT

The performance of M-ary pulse position modulated (PPM) optical wireless communication (OWC) systems in atmospheric weak turbulence medium is evaluated by using adaptive optics corrections. Piston, tilt, defocus and coma components of adaptive optics corrections are applied to the avalanche photodetector (APD) type of receiver and the results are obtained depending on various turbulence and receiver parameters. The lognormal channel distribution is used to model the weak atmospheric turbulence conditions. Adaptive optics correction increases the bit-error-rate (BER) performance of an OWC system operating in atmospheric turbulence conditions. Piston component yields the highest BER performance, followed by the tilt, defocus and coma adaptive optics correction components respectively.     

噪声扰动下RLC串联谐振电路随机共振的数值研究

采用四阶Runge-Kutta算法,以信噪比增益和谱功率放大率为随机共振测度指标,研究了电容参数和激励信号均受高斯白噪声扰动时RLC串联谐振电路的随机共振现象。研究表明,欠阻尼RLC串联谐振电路在适当的电路参数、激励信号频率和噪声参数条件下,信噪比增益和谱功率放大率是噪声强度和输入信号频率的非单调函数,且其值均大于1,电路中存在随机共振现象;而在临界阻尼或过阻尼情况下尽管信噪比增益在一定条件下也是噪声强度和输入信号频率的非单调函数,但谱功率放大率取值小于1,电路发生了随机共振现象,改善了信噪比,信号能量却并未得到加强。这一结论使得将欠阻尼RLC串联谐振电路应用于微弱信号检测成为可能。