Perfluorosulfonic acid—Tetraethoxysilane/polyacrylonitrile (PFSA‐TEOS/PAN) hollow fiber composite membranes prepared for pervaporation dehydration of ethyl acetate–water solutions

Preparation of organic‐inorganic composite membranes and their pervaporation (PV) permeation and separation characteristics for the aqueous solution of ethyl acetate were described. Polyacrylonitrile (PAN) hollow fiber ultrafiltration membrane as support membrane, the mixtures of perfluorosulfonic acid (PFSA) and tetraethoxysilane (TEOS) by the sol‐gel reaction as the coating solution, the PFSA‐TEOS/PAN hollow fiber composite membranes by the different annealing conditions were prepared. The swelling of PFSA in ethyl acetate aqueous solutions was inhibited with addition of TEOS. The PFSA‐TEOS/PAN composite membranes containing up to 30 wt % TEOS in coating solution exhibited high selectivity towards water, then the selectivity decreased and permeation flux increased with increasing the TEOS concentration more than 30 wt %. When the PFSA‐TEOS/PAN composite membranes were annealed, the separation factor increased with increasing annealing temperature and time. Higher annealing temperature and longer annealing time promoted the crosslinking reaction between PFSA and TEOS in PFSA‐TEOS/PAN composite membranes, leading to the enhanced selectivity towards water. For the PFSA/PAN and PFSA‐TEOS/PAN composite membrane with 5 and 30 wt % TEOS annealed at 90°C for 12 h, their PV performance of aqueous solution 98 wt % ethyl acetate were as follows: the separation factors were 30.8, 254 and 496, while their permeation flux were 1430, 513 and 205 g/m² h at 40°C, respectively. In addition, the PV performance of PFSA‐TEOS/PAN composite membranes was investigated at different feed solution temperature and concentration. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation of PFSA‐PVA/PSf hollow fiber membrane for IPA/H2O pervaporation process

Using Na⁺ form of perfluorosulfonic acid (PFSA) and poly(vinyl alcohol) (PVA) as coating materials, polysulfone (PSf) hollow fiber ultrafiltration membrane as a substrate membrane, PFSA‐PVA/PSf hollow fiber composite membrane was fabricated by dip‐coating method. The membranes were post‐treated by two methods of heat treatment and by both heat treatment and chemical crosslinking. Maleic anhydride (MAC) aqueous solution was used as chemical crosslinking agent using 0.5 wt % H₂SO₄ as a catalyst. PFSA‐PVA/PSf hollow fiber composite membranes were used for the pervaporation (PV) separation of isopropanol (IPA)/H₂O mixture. Based on the experimental results, PFSA‐PVA/PSf hollow fiber composite membrane is suitable for the PV dehydration of IPA/H₂O solution. With the increment of heat treatment temperature, the separation factor increased and the total permeation flux decreased. The addition of PVA in PFSA‐PVA coating solution was favorable for the improvement of the separation factor of the composite membranes post‐treated by heat treatment. Compared with the membranes by heat treatment, the separation factors of the composite membranes post‐treated by both heat treatment and chemical crosslinking were evidently improved and reached to be about 520 for 95/5 IPA/water. The membranes post‐treated by heat had some cracks which disappeared after chemical crosslinking for a proper time. Effects of feed temperature on PV performance had some differences for the membranes with different composition of coating layer. The composite membranes with the higher mass fraction of PVA in PFSA‐PVA coating solution were more sensitive to temperature. It was concluded that the proper preparation conditions for the composite membranes were as follows: firstly, heated at 160°C for 1 h, then chemical crosslinking at 40°C for 3 h in 4% MAC aqueous solution. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

全氟磺酸改性聚乙烯醇渗透汽化膜分离乙酸乙酯-水溶液

以聚乙烯醇(PVA)为原材料,全氟磺酸(PFSA)为共混改性材料,以聚丙烯腈(PAN)中空纤维超滤膜为底膜制备了PVAfPAN、PVA-PFSA/PAN复合膜,并用于乙酸乙酯脱水.考察了共混涂膜液中PVA、PFSA配比,交联剂酒石酸(Tat)用量以及原料液温度与浓度对PVA、PAN、PVA-PFSA、PAN复合膜分离件能的影响.实验结果表明,Tac交联的PVA,PAN、PVA-PFSA/PAN复合膜均对水具有较好的分离选择性.共混涂膜液中PVA/PFSA质量比为1/1、Tac/PVA质量比为l/5时所制备的PVA-PFSA/PAN复合膜渗透汽化分离性能最佳.40下℃此复合膜用于分离98%(wt)的乙酸乙酯水溶液时,其渗透通量和分离因予分别为81.1 g·m-2·h-1和1890.同样条件下,与交联PVA/PAN复合膜相比,交联PVA-PFSA/PAN复合膜的渗透通量显著提高.     

Esterification over rare earth oxide and alumina promoted SO4/ZrO2

Solid superacid catalysts including SO₄²⁻/ZrO₂ (SZ), rare earth (RE) oxide-promoted SZ and RE oxides together with alumina-promoted SZ were prepared. Their catalytic performances in the esterification reaction of ethanol and acetic acid were investigated. The textural property, crystalline phase and surface acidity of the prepared catalysts were characterized by using nitrogen adsorption–desorption isotherms, X-ray diffraction (XRD) and Fourier-transform infrared (FTIR) spectroscopy of pyridine adsorption techniques, respectively. Effects of the reaction time and catalyst reuse cycle as well as catalyst regeneration on the catalytic behaviors were studied. Experimental results showed that Yb₂O₃–Al₂O₃ promoted SZ (designated as SZAY) catalyst exhibited an optimal esterification performance; the Lewis acid sites with moderate and super strong strength could mainly be responsible for the esterification reaction; and doping both Yb₂O₃ and Al₂O₃ on SZ not only boosted the esterification activity but also alleviated catalyst deactivation resulted from the surface sulfur loss by solvation.     

Aging phenomenon of 6FDA-polyimide/polyacrylonitrile composite hollow fibers

We have observed time-dependent drifts in permeability and selectivity for two types of composite hollow fibers used for air separation. One was PVP [poly(4-vinyl pyridine)]/6FDA-durene/polyacrylonitrile (PAN) composite hollow fiber, and the other was 6FDA-3,5-diaminobenzonitrile/6FDA-durene/PAN composite hollow fiber. Their permeabilities dropped 50 to 70% after 3 to 5 months, while selectivities for O₂N₂ deteriorated slightly with time. A systematic study was carried out to investigate the causes of this creep behavior. Various composite fibers, such as polyimide/Celgard and polyimide siloxane/PAN, were fabricated to simulate the aging process. We conclude that the aging phenomenon observed for these two 6FDA-durene/PAN composite fibers was not due to the structure change of the PAN substrate, but mainly to the densification effect of the 6FDA-durene gutter layer on composite fibers. © 1996 John Wiley & Sons, Inc.     

Pervaporation dehydration of ethyl acetate aqueous solution using the doubly modified polyvinyl alcohol (PVA) composite membrane

Polyvinyl alcohol–tetraethoxysilane–perfluorosulfonic acid (PVA–TEOS–PFSA) hybrid membrane was prepared by sol–gel method through PVA being modified doubly by PFSA and TEOS. With polyacrylonitrile (PAN) ultrafiltration membrane as a substrate membrane, PVA–TEOS–PFSA/PAN composite membrane was fabricated by dip-coating method for pervaporation (PV) dehydration of ethyl acetate (EAc) aqueous solution. The hybrid membrane was characterized by swelling degree, static contact angle, Fourier transform infrared spectra and scanning electron microscope. Effects of PFSA and TEOS contents in coating solution on PV performance of composite membrane were investigated, respectively. With increasing PFSA content, the permeation flux of composite membrane increased, while the separation factor decreased. Just the opposite, the increase of TEOS content resulted in the decrease in permeation flux and the increase in separation factor. In addition, the PV performances of composite membranes were also investigated at different feed temperatures and water concentrations in feed, respectively. The PVA–TEOS–PFSA/PAN composite membrane, which was prepared from coating with PVA/PFSA mass ratio of 80/20 and TEOS content of 20 wt%, exhibited the permeation flux of 347.9 g m^?2 h^?1 and the separation factor of 2218 for PV dehydration of 2 wt% water of EAc solution at 40 °C.     

Polyvinyl alcohol/polysulfone (PVA/PSF) hollow fiber composite membranes for pervaporation separation of ethanol/water solution

Polysulfone (PSF) hollow fiber membranes were spun by phase‐inversion method from 29 wt % solids of 29 : 65 : 6 PSF/NMP/glycerol and 29 : 64 : 7 PSF/DMAc/glycol using 93.5 : 6.5 NMP/water and 94.5 : 5.5 DMAc/water as bore fluids, respectively, while the external coagulant was water. Polyvinyl alcohol/polysulfone (PVA/PSF) hollow fiber composite membranes were prepared after PSF hollow fiber membranes were coated using different PVA aqueous solutions, which were composed of PVA, fatty alcohol polyoxyethylene ether (AEO₉), maleic acid (MAC), and water. Two coating methods (dip coating and vacuum coating) and different heat treatments were discussed. The effects of hollow fiber membrane treatment methods, membrane structures, ethanol solution temperatures, and MAC/PVA ratios on the pervaporation performance of 95 wt % ethanol/water solution were studied. Using the vacuum‐coating method, the suitable MAC/PVA ratio was 0.3 for the preparation of PVA/PSF hollow fiber composite membrane with the sponge‐like membrane structure. Its pervaporation performance was as follows: separation factor (α) was 185 while permeation flux (J) was 30g/m²·h at 50°C. Based on the experimental results, it was found that separation factor (α) of PVA/PSF composite membrane with single finger‐void membrane structure was higher than that with the sponge‐like membrane structure. Therefore, single finger‐void membrane structure as the supported membrane was more suitable than sponge‐like membrane structure for the preparation of PVA/PSF hollow fiber composite membrane. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 247–254, 2005     

PVA/SO42——AAO催化-渗透汽化双功能复合膜合成乙酸乙酯

采用浸渍-涂覆法制备了聚乙烯醇/阳极氧化铝固体酸（PVA/SO₄^2--AAO）催化-渗透汽化双功能膜,并用于乙酸与乙醇的催化酯化反应。用SEM、XRD、NH₃-TPD分析了双功能膜的结构及性能。考察了双功能膜用量、乙酸/乙醇摩尔比及反应温度对酯化反应转化率的影响。结果表明：乙酸/双功能膜质量比为30∶1,乙酸/乙醇摩尔比为4∶1,料液温度为80℃时乙醇的500 min转化率可以达到87%。反应活化能为41.84 kJ/mol,比浓硫酸作催化剂的经典反应活化能降低6.74 kJ/mol。     

催化剂对酯化反应渗透汽化膜稳定性的影响

比较了酯化反应耦合渗透汽化膜反应器中不同的催化剂体系及其含量对ＰＰＶＡ／ＰＡＮ复合膜稳定性的影响。试验结果表明,固体超强酸催化剂体系对复合膜的稳定性没有影响。活性层酯化度为３．３％及６．２％的复合膜具有良好的稳定性。能够适合于酯化反应耦合渗透汽化过程研究及应用。     

Novel Hollow Titania Spheres‐Chitosan Hybrid Membranes with High Isopropanol Dehydration Performance

A new kind of hollow titania spheres‐chitosan (hTiO₂‐CS) hybrid membranes was prepared by a physical blending method. hTiO₂ spheres were found to disperse well in the as‐prepared hTiO₂‐CS hybrid membranes. Their incorporation can reduce the chitosan crystallinity and enhance slightly its hydrophilicity and thermal stability. Subsequently, hTiO₂‐CS/PAN composite membranes comprising of the hTiO₂‐CS hybrid membrane as separation layer and a polyacrylonitrile (PAN) membrane as support layer were fabricated. Compared to the CS/PAN membrane, all of them exhibit a much better flux and separation factor for a 90 wt % aqueous solution of isopropanol at 80 °C. This promising kind of composite membranes may find potential application in the dehydration of alcohols.     

Modification of Thin Film Composite PVA/PAN Membranes for Pervaporation Using Aluminosilicate Nanoparticles

The effect of the modification of the polyvinyl alcohol (PVA) selective layer of thin film composite (TFC) membranes by aluminosilicate (Al₂O₃·SiO₂) nanoparticles on the structure and pervaporation performance was studied. For the first time, PVA-Al₂O₃·SiO₂/polyacrylonitrile (PAN) thin film nanocomposite (TFN) membranes for pervaporation separation of ethanol/water mixture were developed via the formation of the selective layer in dynamic mode. Selective layers of PVA/PAN and PVA-Al₂O₃·SiO₂/PAN membranes were formed via filtration of PVA aqueous solutions or PVA-Al₂O₃·SiO₂ aqueous dispersions through the ultrafiltration PAN membrane for 10 min at 0.3 MPa in dead-end mode. Average particle size and zeta potential of aluminosilicate nanoparticles in PVA aqueous solution were analyzed using the dynamic light scattering technique. Structure and surface properties of membranes were studied using scanning electron microscopy (SEM), atomic force microscopy (AFM) and water contact angle measurements. Membrane performance was investigated in pervaporation dehydration of ethanol/water mixtures in the broad concentration range. It was found that flux of TFN membranes decreased with addition of Al₂O₃·SiO₂ nanoparticles into the selective layer due to the increase in selective layer thickness. However, ethanol/water separation factor of TFN membranes was found to be significantly higher compared to the reference TFC membrane in the whole range of studied ethanol/water feed mixtures with different concentrations, which is attributed to the increase in membrane hydrophilicity. It was found that developed PVA-Al₂O₃·SiO₂/PAN TFN membranes were more stable in the dehydration of ethanol in the whole range of investigated concentrations as well as at different temperatures of the feed mixtures (25 °C, 35 °C, 50 °C) compared to the reference membrane which is due to the additional cross-linking of the selective layer by formation hydrogen and donor-acceptor bonds between aluminosilicate nanoparticles and PVA macromolecules.     

Pd/Al2O3 composite hollow fibre membranes: Effect of substrate resistances on H2 permeation properties

Al₂O₃ hollow fibres with different asymmetric macrostructures, i.e. various thickness ratios between a finger-like layer and a sponge-like layer, have been prepared by a phase inversion/sintering technique. Such asymmetric hollow fibres are used as substrates on which Pd membrane is deposited directly by an electroless plating (ELP) technique without any pre-treatment on substrate surface. Influences of the substrate macrostructure on hydrogen permeation through the Pd/Al₂O₃ composite membranes have been investigated both experimentally and theoretically. The hydrogen permeation through the Pd/Al₂O₃ composite membranes was not only determined by the Pd membrane thickness, but also by the macrostructural parameters of the substrate, such as effective porosity, mean pore size and pore size distribution etc. The thinner the Pd membrane, the higher the effective porosity is required to alleviate the substrate effect on the hydrogen permeation. Also, the deviation of the pore size is suggested to be around 1.2 for the further improved hydrogen permeation through the composite hollow fibre membranes.     

PPVA/PAN渗透汽化复合膜分离特性研究

利用磷酸对聚乙烯醇进行酯化改性,制备了以磷酸酯化聚乙烯醇（ＰＰＶＡ）为生分离层的ＰＰＶＡ／ＰＡＮ渗透汽化复合膜用于乙醇一水混合中物的分离。试验结果表明,ＰＰＶＡ／ＰＡＮ复合膜对水具有较好的分离性能。考察了ＰＰＶＡ活性分离层的酯化度、分离湿度、进料浓度等因素对复 摹分离性能的影响。对复合膜活性分离吸附性能与共分离性能的关系研究表明,活性分离层的吸附充分反映了其分离性能。     

Preparation of polyvinylamine/polysulfone composite hollow‐fiber membranes and their CO2/CH4 separation performance

Fixed‐carrier composite hollow‐fiber membranes were prepared with polyvinylamine (PVAm) as the selective layer and a polysulfone ultrafiltration membrane as the substrate. The effects of the PVAm concentration in the coating solution, the number of coatings, and the crosslinking of glutaraldehyde and sulfuric acid on the CO₂ permeation rate and CO₂/CH₄ selectivity of the composite membranes were investigated. As the PVAm concentration and the number of coatings increased, the CO₂/CH₄ selectivity increased, but the CO₂ permeation rate decreased. The membranes crosslinked by glutaraldehyde or sulfuric acid possessed higher CO₂/CH₄ selectivities but lower CO₂ permeation rates. For the pure feed gas, a composite hollow‐fiber membrane coated with a 2 wt % PVAm solution two times and then crosslinked with glutaraldehyde and an acid solution in sequence had a CO₂ permeation rate of 3.99 × 10^?6 cm³ cm^?2 s^?1 cmHg^?1 and an ideal CO₂/CH₄ selectivity of 206 at a feed gas pressure of 96 cmHg and 298 K. The effect of time on the performance of the membranes was also investigated. The performance stability of the membranes was good during 6 days of testing. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1885–1891, 2006     

Preparation and characterization of braided tube reinforced polyacrylonitrile hollow fiber membranes

Polyacrylonitrile (PAN) and polyester (PET) braided hollow tube that used as a special reinforcement are braided from their filaments via two‐dimensional weaving techniques. PAN braided tube reinforced homogeneous PAN hollow fiber membranes and PET braided tube reinforced heterogeneous PAN hollow fiber membranes are prepared by concentric circles squeezed‐coated spinning method. As for PAN hollow fiber membrane, the effects of PAN concentration on the performance of the prepared hollow fiber membranes are investigated in terms of pure water flux, protein rejection, mechanical strength, and morphology observations by a scanning electron microscope (SEM). The interfacial bonding state of the braided tube reinforced PAN hollow fiber membranes is studied by constant speed stretching method. Results show that the breaking strength of two‐dimensional braided tube reinforced PAN hollow fiber membranes is higher than 80 MPa. The structure of separation surface is similar to the structure of an asymmetric membrane. With the increase of polymer concentration, the membrane flux decreases while the retention rate of BSA increase. The membrane porosity and maximum pore size have the same decreasing tendency as the increase of PAN concentration. The results also show that the interfacial bonding state of the PAN two‐dimensional braided tube reinforced homogeneous PAN hollow fiber membranes is better than that of the PET two‐dimensional braided tube reinforced heterogeneous PAN hollow fiber membranes. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41795.     

影响渗透汽化中空纤维复合膜分离性能的制备工艺研究

采用聚乙烯醇（ＰＶＡ）为分离层的模材料,以浸涂工艺把ＰＶＡ复合到聚砜（ＰＳ）或聚丙烯腈（ＰＡＮ）的中空纤维支撑层上,在长度为０．４ｍ的不锈钢管中组装若干根中空纤维复合膜测定对乙醇水溶液的渗透汽化（ＰＶ）分离性能。结果表明,ＰＶＡ／ＰＡＮ中空纤维复合膜的性能优于ＰＶＡ／ＰＳ,内径较大（１．３ｍｍ）的优于内径上（０．４ｍｍ）者,ＰＶＡ水溶液在中空纤维支撑层上的涂复次数对复合膜ＰＶ分离性能、以及ＰＶＡ／     

PVAm/PAN复合膜的制备及其对CO2/CH4的分离性能

New polymeric membrane materials——polyvinyl amine (PVAm) with different primary amine contents were synthesized.By covering polyacrylonitrile(PAN) ultrafiltration membranes with PVAm, the PVAm/PAN composite membranes for CO₂/CH₄ separation were prepared. The composite membranes containing more primary amino groups have higher selectivity for CO₂/CH₄.The cross-linking of acid or glutaradehyde could improve the gas permselectivity of the composite membranes. With decreasing CO₂ content in the feed gas, the CO₂/CH₄ separation factor increased.When the feed gas was 25%(vol) CO₂ and 75%(vol) CH₄, the CO₂ permeation rate was 4.1×10^-9cm³(STP) •cm^-2•Pa^-1•s^-1, and the CO₂/CH₄ separation factor was 180.     

Preparation and performance of braid‐reinforced poly(vinyl chloride) hollow fiber membranes

A novel braid‐reinforced (BR) poly(vinyl chloride) (PVC) hollow fiber membrane was fabricated via dry‐wet spinning process. The mixtures of PVC polymer solutions were uniformly coated on the tubular braid which contained polyester (PET) and polyacrylonitrile (PAN) fibers. The influences of braid composition on structure and performance of BR PVC hollow fiber membranes were investigated. The results showed that the prepared BR PVC hollow fiber membranes were composed of two layers which contained separation layer and tubular braid supported layer when the PET and PET/PAN hybrid tubular braids were used as the reinforcement. But the sandwich structure appeared when the PAN tubular braid was used as the reinforcement, which revealed outer separation layer, tubular braid supported layer and the inner polymer layer. The BR PVC hollow fiber membranes that prepared by PET/PAN hybrid tubular braid had favorable interfacial bonding state compared with the membrane prepared by pure PET or PAN tubular braid. The pure water flux of the BR PVC hollow fiber membranes that prepared by the PET/PAN hybrid tubular braid were lower than that prepared by pure PET or PAN tubular braid, but the rejection of Bovine serum albumin was opposite. The tensile strength of prepared BR PVC hollow fiber membrane was higher than 50 MPa. Both of the tensile strength and elongation at break decreased with the increase of the PAN filaments in the PET/PAN hybrid tubular braid. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45068.     

中空纤维PVA/PAN复合膜填料的乙醇水溶液精馏性能

以乙醇/水溶液为分离对象,中空纤维PVA/PAN复合膜作为精馏填料,考察了不同膜组件的传质分离效率。实验结果表明:各种组件的分离效率均随塔釜加热功率的增加而减小;和大多数中空纤维膜接触器一样,其总传质系数Ky随中空纤维膜组件填充密度φ的增加而减少;相比于传统精馏填料而言,用中空纤维膜做精馏填料分离乙醇水溶液的分离效果更好,可以在常规填料不能操作的液泛线以上进行操作。当塔釜加热功率为120 W,45根中空纤维膜封装在内径为1.6 cm玻璃管中的传质单元高度(HTU)为5.64 cm。     

Preparation and characterization of alumina hollow fiber membranes

With the rapid development of membrane technology in water treatment, there is a growing demand for membrane products with high performance. The inorganic hollow fiber membranes are of great interest due to their high resistance to abrasion, chemical/thermal degradation, and higher surface area/volume ratio therefore they can be utilized in the fields of water treatment. In this study, the alumina (Al₂O₃) hollow fiber membranes were prepared by a combined phase-inversion and sintering method. The organic binder solution (dope) containing suspended Al₂O₃ powders was spun to a hollow fiber precursor, which was then sintered at elevated temperatures in order to obtain the Al₂O₃ hollow fiber membrane. The dope solution consisted of polyethersulfone (PES), Nmethyl-2-pyrrolidone (NMP) and polyvinylpyrrolidone (PVP), which were used as polymer binder, solvent and additive, respectively. The prepared Al₂O₃ hollow fiber membranes were characterized by a scanning electron microscope (SEM) and thermal gravimetric analysis (TG). The effects of the sintering temperature and Al₂O₃/PES ratios on the morphological structure, pure water flux, pore size and porosity of the membranes were also investigated extensively. The results showed that the pure water flux, maximum pore size and porosity of the prepared membranes decreased with the increase in Al₂O₃/PES ratios and sintering temperature. When the Al₂O₃/PES ratio reached 9, the pure water flux and maximum pore size were at 2547 L/m²·h and 1.4 μm, respectively. Under 1600dgC of sintering temperature, the pure water flux and maximum pore size reached 2398 L/(m²·h) and 2.3 μm, respectively. The results showed that the alumina hollow fiber membranes we prepared were suitable for the microfiltration process. The morphology investigation also revealed that the prepared Al₂O₃ hollow fiber membrane retained its’asymmetric structure even after the sintering process.