Synthesis, structure, and photovoltaic property of a nanocrystalline 2H perovskite-type novel sensitizer (CH3CH2NH3)PbI3

A new nanocrystalline sensitizer with the chemical formula (CH₃CH₂NH₃)PbI₃ is synthesized by reacting ethylammonium iodide with lead iodide, and its crystal structure and photovoltaic property are investigated. X-ray diffraction analysis confirms orthorhombic crystal phase with a = 8.7419(2) Å, b = 8.14745(10) Å, and c = 30.3096(6) Å, which can be described as 2 H perovskite structure. Ultraviolet photoelectron spectroscopy and UV-visible spectroscopy determine the valence band position at 5.6 eV versus vacuum and the optical bandgap of ca. 2.2 eV. A spin coating of the CH₃CH₂NH₃I and PbI₂ mixed solution on a TiO₂ film yields ca. 1.8-nm-diameter (CH₃CH₂NH₃)PbI₃ dots on the TiO₂ surface. The (CH₃CH₂NH₃)PbI₃-sensitized solar cell with iodide-based redox electrolyte demonstrates the conversion efficiency of 2.4% under AM 1.5 G one sun (100 mW/cm²) illumination.     

Reduction of lean NOx by ethanol over Ag/Al2O3 catalysts in the presence of H2O and SO2

The reduction of lean NOx using ethanol in simulated diesel engine exhaust was carried out over Ag/Al₂O₃ catalysts in the presence of H₂O and SO₂. The Ag/Al₂O₃ catalysts are highly active for the reduction of lean NOx by ethanol but the reaction is accompanied by side reactions to form CH₃CHO, CO along with small amounts of hydrocarbons (C₃H₆, C₂H₄, C₂H₂ and CH₄) and nitrogen compounds such as NH₃ and N₂O. The presence of H₂O enhances the NOx reduction while SO₂ suppresses the reduction. The presence of SO₂ along with H₂O suppresses the formation of acetaldehyde and NH₃. By infrared spectroscopy, it was revealed that the reactivity of NCO species formed in the course of the reaction was greatly enhanced in the presence of H₂O. The NCO species readily reacts with NO in the presence of O₂ and H₂O at room temperature, being converted to N₂ and CO₂ (CO). Addition of SO₂ suppresses the formation of NCO species and lowers the reactivity of the NCO species. However, the reduction of NOx is still kept at high conversion levels in the presence of H₂O and SO₂ over the present catalysts. About 80% of NOx in the simulated diesel engine exhaust was removed at 743 K. This revised version was published online in July 2006 with corrections to the Cover Date.     

Influence of Al2O3 support on the activity of Ag/Al2O3 catalysts for SCR of NO with decane

The role of the Al₂O₃ support on the activity of supported Ag catalyst towards the selective catalytic reduction (SCR) of NO with decane is elucidated. A series of Ag/Al₂O₃ catalysts were prepared by impregnation method and characterized by N₂ pore size distribution, XRD, UV–Vis, in-situ FT-IR and acidity measurement by NH₃ and pyridine adsorption. The catalytic activity differences of Ag/Al₂O₃ are correlated with different properties of Al₂O₃ supports and the active Ag species formed. 4wt% Ag supported on sol-gel prepared Al₂O₃ (Ag/Al₂O₃ (SG), showed higher NO _x conversion (65% at 400 °C), compared with the respective catalysts made from commercial Al₂O₃ (Ag/Al₂O₃ (GB), Ag/Al₂O₃ (ALO), (∼26 and 7% at 400 °C). The higher surface area, acidity and pore size distribution in sol–gel prepared Al₂O₃ (SG) results in higher NO and hydrocarbon conversion. Based on the UV–vis characterization, the activity of NO reduction is correlated to the presence of Ag_n^δ+ clusters and acidity of Al₂O₃ support was found to be one of the important parameter in promoting the formation and stabilization of Ag_n^δ+ clusters. Furthermore from pyridine adsorption results, presence of more number of Bronsted acid sites in Ag/Al₂O₃ (SG) is confirmed, which could also contribute to low temperature hydrocarbon activation and improve NO conversion. In situ FT-IR measurements revealed the higher rate of –CN and –NCO intermediate species formation over 4wt% Ag/Al₂O₃ (SG). We conclude that the physico–chemical properties of Al₂O₃ play a crucial role in NO _x conversion over Ag/Al₂O₃ catalysts. Thus, the activity of the Ag/Al₂O₃ catalyst can be tailored by using a proper type of Al₂O₃ support.     

Synthesis and electrochemical characteristics of Al2O3-coated LiNi1/3Co1/3Mn1/3O2 cathode materials for lithium ion batteries

LiNi_1/3Co_1/3Mn_1/3O₂ cathode materials have been coated with Al₂O₃ nano-particles using sol-gel processing to improve its electrochemical properties. The X-ray diffraction (XRD) pattern of the as-prepared Al₂O₃ nano-particles was indexed to the cubic structure of the γ-Al₂O₃ phase and had an average size of ∼4 nm. The XRD showed that the structure of LiNi_1/3Co_1/3Mn_1/3O₂ was not affected by the Al₂O₃ coating. However, the Al₂O₃ coatings on LiNi_1/3Co_1/3Mn_1/3O₂ improved the cyclic life performance and rate capability without decreasing its initial discharge capacity. These electrochemical properties were also compared with those of LiAlO₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ cathode material. The electrochemical impedance spectroscopy (EIS) was studied to understand the enhanced electrochemical properties of the Al₂O₃-coated LiNi_1/3Co_1/3Mn_1/3O₂ compared to uncoated LiNi_1/3Co_1/3Mn_1/3O₂.     

Influence of argon plasma on the deposition of Al2O3 film onto the PET surfaces by atomic layer deposition

In this paper, polyethyleneterephthalate (PET) films with and without plasma pretreatment were modified by atomic layer deposition (ALD) and plasma-assisted atomic layer deposition (PA-ALD). It demonstrates that the Al₂O₃ films are successfully deposited onto the surface of PET films. The cracks formed on the deposited Al₂O₃ films in the ALD, plasma pretreated ALD, and PA-ALD were attributed to the energetic ion bombardment in plasmas. The surface wettability in terms of water contact angle shows that the deposited Al₂O₃ layer can enhance the wetting property of modified PET surface. Further characterizations of the Al₂O₃ films suggest that the elevated density of hydroxyl -OH group improve the initial growth of ALD deposition. Chemical composition of the Al₂O₃-coated PET film was characterized by X-ray photoelectron spectroscopy, which shows that the content of C 1s reduces with the growing of O 1s in the Al₂O₃-coated PET films, and the introduction of plasma in the ALD process helps the normal growth of Al₂O₃ on PET in PA-ALD.     

Semitransparent inverted polymer solar cells employing a sol-gel-derived TiO2 electron-selective layer on FTO and MoO3/Ag/MoO3 transparent electrode

We report a new semitransparent inverted polymer solar cell (PSC) with a structure of glass/FTO/nc-TiO₂/P3HT:PCBM/MoO₃/Ag/MoO₃. Because high-temperature annealing which decreased the conductivity of indium tin oxide (ITO) must be handled in the process of preparation of nanocrystalline titanium oxide (nc-TiO₂), we replace glass/ITO with a glass/fluorine-doped tin oxide (FTO) substrate to improve the device performance. The experimental results show that the replacing FTO substrate enhances light transmittance between 400 and 600 nm and does not change sheet resistance after annealing treatment. The dependence of device performances on resistivity, light transmittance, and thickness of the MoO₃/Ag/MoO₃ film was investigated. High power conversion efficiency (PCE) was achieved for FTO substrate inverted PSCs, which showed about 75% increase compared to our previously reported ITO substrate device at different thicknesses of the MoO₃/Ag/MoO₃ transparent electrode films illuminated from the FTO side (bottom side) and about 150% increase illuminated from the MoO₃/Ag/MoO₃ side (top side).     

In situ-prepared composite materials of PEDOT: PSS buffer layer-metal nanoparticles and their application to organic solar cells

We report an enhancement in the efficiency of organic solar cells via the incorporation of gold (Au) or silver (Ag) nanoparticles (NPs) in the hole-transporting buffer layer of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS), which was formed on an indium tin oxide (ITO) surface by the spin-coating of PEDOT:PSS-Au or Ag NPs composite solution. The composite solution was synthesized by a simple in situ preparation method which involved the reduction of chloroauric acid (HAuCl₄) or silver nitrate (AgNO₃) with sodium borohydride (NaBH₄) solution in the presence of aqueous PEDOT:PSS media. The NPs were well dispersed in the PEDOT:PSS media and showed a characteristic absorption peak due to the surface plasmon resonance effect. Organic solar cells with the structure of ITO/PEDOT:PSS-Au, Ag NPs/poly(3-hexylthiophene):[6,6]-phenyl-C61-butyric acid methyl ester (P3HT:PCBM)/LiF/Al exhibited an 8% improvement in their power conversion efficiency mainly due to the enlarged surface roughness of the PEDOT:PSS, which lead to an improvement in the charge collection and ultimately improvements in the short-circuit current density and fill factor.     

Al2O3-coated SnO2/TiO2 composite electrode for the dye-sensitized solar cell

A novel Al₂O₃-coated SnO₂/TiO₂ composite electrode has been applied to the dye-sensitized solar cell. In such an electrode, two kinds of energy barriers (SnO₂/TiO₂ and TiO₂/Al₂O₃) were designed to suppress the recombination processes of the photo-generated electrons and holes. After the SnO₂ was modified by colloid TiO₂, the photoelectric conversion efficiency of the SnO₂/TiO₂ composite cell increased to 2.08% by a factor of 2.8 comparing with that of the SnO₂ cell. The Al₂O₃ layer on the SnO₂/TiO₂ composite electrode further suppressed the generation of the dark current, resulting in 37% improvement in device performance comparing with the SnO₂/TiO₂ cell.     

Trapping of CH3O formed from CO + H2

Methoxy formed on Al₂O₃ from¹³CO and H₂ coadsorption on Ni/Al₂O₃ was trapped by C₂H₅OH adsorption and temperature-programmed reaction (TPR). The presence of excess C₂H₅OH significantly increases the rate of¹³CH₃OH and (¹³CH₃)₂O formation. The¹³CH₃OH forms by the reaction of C₂H₅OH with¹³CH₃O on Al₂O₃. In the absence of C₂H₅OH,TPR following¹³CO and H₂ coadsorption did not produce significant amounts of¹³CH₃OHor(¹³CH₃)₂O.     

Highly hydrogen-deficient hydrocarbon species for the CO2-reforming of CH4 on Co/Al2O3 catalyst

The dynamics of produced CO and H₂, measured by pulse surface reaction rate analysis (PSRA), revealed that the intermediate hydrocarbon species for the CO₂-reforming of CH₄ was highly hydrogen-deficient (CH_0.75) on supported Co/Al₂O₃ catalyst. It was also found that the species was more reactive than the less hydrogen-deficient one (CH_2.4) on Ni/Al₂O₃ catalyst.     

Low-temperature atomic layer deposited Al2O3 thin film on layer structure cathode for enhanced cycleability in lithium-ion batteries

The deposition of Al₂O₃ on LiCoO₂ electrodes using a low-temperature atomic layer deposition has been investigated. Scanning electron microscopy confirms that Al₂O₃ films can be homogeneously deposited on LiCoO₂ particles of porous electrodes at 120 °C. The results of X-ray photoelectron spectroscopy show that the Al₂O₃ preferentially deposits on the LiCoO₂. Furthermore, the results of cycling stability tests show that the cells with Al₂O₃-coated LiCoO₂ electrodes have enhanced performance.     

Decomposition and oxidation of CH3 13CH2OH on A12O3, Pd/Al2O3, and PdO/Al2O3 catalysts

Temperature-programmed desorption (TPD) and oxidation (TPO) were used to investigate the decomposition and oxidation of ethanol on Al₂O₃, Pd/Al₂O₃, and PdO/Al₂O₃. Ethyl--¹³C alcohol (CH₃ ¹³CH₂OH) was adsorbed on the catalysts so that reaction pathways of the two carbons could be distinguished. Alumina was mainly a dehydration catalyst, but dehydrogenation was also observed and some carbon remained on the surface. In the presence of O₂, A1₂O₃ oxidized the decomposition products and the-carbon was oxidized faster. Ethanol, which was adsorbed on A1₂O₃, decomposed much faster on Pd/A1₂O₃ by diffusing to Pd and undergoing CO elimination to form CH₄,¹³CO, H₂, and surface carbon. On PdO/A1₂O₃, the decomposition was slower than on Pd/A1₂O₃ until lattice oxygen was extracted above 450 K; the decomposition products were oxidized by lattice oxygen. In the presence of gas phase O₂, Pd/Al₂O₃ was an active oxidation catalyst at low temperature, but lattice oxygen had to be extracted from PdO/A1₂O₃ before it had significant oxidation activity.     

Reactivity of surface isocyanate species with NO, O2 and NO+O2 in selective reduction of NOχ over Ag/Al2O3 and Al2O3 catalysts

Reactivity of surface isocyanate (NCO(a)) species with NO, O₂ and NO+O₂ in selective reduction of NOχ over Ag/Al₂O₃ and Al₂O₃ catalysts was studied by a pulse reaction technique and an in situ diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy. The NCO(a) species on Ag/Al₂O₃ reacted with O₂ or NO+O₂ mixture gas to produce N₂ effectively above 200°C, while the reaction of NCO(a) with NO hardly produced N₂ even at 350°C. In the case of Al₂O₃ alone, less N₂ was detected in the reaction of NCO(a) with NO+O₂, indicating that silver plays an important role in the N₂ formation from NCO(a). These behaviors of the reactivity of NCO(a) species with reactant gases were in good agreement with the changes in NCO(a) bands shown by in situ DRIFT measurements. Based on these findings, the role of NCO(a) species in the selective reduction of NOχ on Ag/Al₂O₃ and Al₂O₃ catalysts is discussed. This revised version was published online in July 2006 with corrections to the Cover Date.     

Infrared spectroscopic study and characteristics of SnO2-based thick film for CH3CN detection

The SnO₂/Al₂O₃/Nb₂O₅/ISiO₂ thick film devices were fabricated by screen printing and dipping methods, and their sensing characteristics to CH₃CN gas was investigated. The oxidation products of CH₃CN on the thick film were analyzed by FT-IR using a heatable gas cell. The IR results showed that the products formed by oxidation of CH₃CN at 300 ‡C on the SnO₂/Al₂/Nb₂O₅ thick film without SiO₂ were mainly CO₂, H₂O, and NH₃, while on the SnO₂/Al₂O₃/Nb₂O₅/SiO₂ thick film products such as CO₂, H₂O, N₂O, HNO₃, and HNO₂ were observed. The thick film devices containing SiO₂ showed high selectivity and negative sensitivity to CH₃CN due to the presence of nitrogen compounds produced by oxidation of CH₃CN. Optimum amount of Nb₂O₅ and operating temperature were 1. 0 wt% and 300 ‡C, respectively.     

Characterization of Sn doped Ni/Al2O3 steam reforming catalysts by XPS

XPS measurements have shown that tin oxides are more readily reduced to metallic tin by hydrogen in Ni/Al₂O₃ systems than on pure Al₂O₃. During the reductive activation of Sn doped Ni/Al₂O₃ catalysts, surface segregation of the dopant was observed. This finding may explain that tin enhances the selectivity of the steam reforming catalysts only when added in very low concentrations and that it acts as a poison at higher loadings.     

Combustion of Methane at Low Temperature over Pd and Pt Catalysts Supported on Al2O3, SnO2 and Al2O3-Grafted SnO2

Pd and Pt catalysts supported on alumina, tin(IV) oxide and tin(IV) oxide grafted on alumina were prepared, characterised and tested with respect to the low-temperature combustion of methane after reduction in H₂ and ageing under reactants at 600°C. In the case of Pd, the use of SnO₂ or SnO₂-based supports led to catalysts slightly less active than Pd/Al₂O₃. In contrast, SnO₂ was found to strongly promote the oxidation of methane over Pt catalysts with respect to Pt/Al₂O₃, even after ageing under reactants. When Pt was supported on SnO₂ grafted on Al₂O₃, the activity was found at most similar to or, after ageing, lower than Pt/Al₂O₃. This negative effect was discussed, being partly related to the sintering of SnO₂ under reactants observed by FTIR and XRD.     

Study on photoelectrochemical solar cells of nanocrystalline Cd0.7Zn0.3Se -water soluble conjugated polymer

Cadmium zinc selenide (Cd_0.7Zn_0.3Se) nanocrystalline thin films were chemically synthesized onto indium tin oxide (ITO)-coated glass substrate at relatively low temperature (<90 °C). The as-deposited films were annealed in air at 200, 300, and 400 °C for 60 min. The structure and surface morphology of the films were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The water-soluble conjugated polymer, poly(2-ethynyl-N-carboxy-propyl-pyridinium bromide) (LM3), with quaternary pyridinium salts was layered by dipping the as-deposited and annealed Cd_0.7Zn_0.3Se films in the aqueous polymer solution. This hybrid photoanode system was subjected to photoelectrochemical (PEC) study under a light illumination intensity of 80 mW/cm².     

Support modification to improve the sulphur tolerance of Ag/Al2O3 for SCR of NOx with propene under lean-burn conditions

Ag/Al₂O₃ catalysts with 1 wt% SiO₂ or TiO₂ doping in alumina support have been prepared by wet impregnation method and tested for sulphur tolerance during the selective catalytic reduction (SCR) of NO_x using propene under lean conditions. Ag/Al₂O₃ showed 44% NO_x conversion at 623 K, which was drastically reduced to 21% when exposed to 20 ppm SO₂. When Al₂O₃ support in Ag/Al₂O₃ was doped with 1 wt% SiO₂ or TiO₂ the NO_x conversion remained constant in presence of SO₂ showing the improved sulphur tolerance of these catalysts. Subsequent water addition does not induce significant deactivation. On the contrary, a slight promotional effect on the activity of NO conversion to nitrogen is observed after Si and Ti incorporation. FTIR study showed the sulphation of silver and aluminum sites of Ag/Al₂O₃ catalysts resulting in the decrease in the formation of reactive intermediate species such as –NCO, which in turn decreases NO_x conversion to N₂. In the case of Ag/Al₂O₃ doped with SiO₂ or TiO₂, formation of silver sulphate and aluminum sulphate was drastically reduced, which was evident in FTIR resulting in remarkable improvement in the sulphur tolerance of Ag/Al₂O₃ catalyst. These catalysts before and after the reaction have been characterized with various techniques (XRD, BET surface area, transmittance FTIR and pyridine adsorption) for physico-chemical properties.     

A Novel Catalyst Pt/CoAl2O4/Al2O3 for Combination CO2 Reforming and Partial Oxidation of CH4

Pt/CoAl₂O₄/Al₂O₃, Pt/CoO_x/Al₂O₃, CoAl₂O₄/Al₂O₃ and CoO_x/Al₂O₃ catalysts were studied for combination CO₂ reforming and partial oxidation of CH₄. The results indicate that Pt/CoAl₂O₄/Al₂O₃ is the most effective, and XRD results indicate that Pt species are well dispersed over the Pt/CoAl₂O₄/Al₂O₃. High dispersion is related to the presence of CoAl₂O₄, formed during calcining at high temperature before Pt addition. In the presence of Pt, CoAl₂O₄ in the catalyst could be reduced partially at 973 K. Based on these results, it appears that zerovalent platinum with high dispersion and zerovalent cobalt resulting from CoAl₂O₄ reduction are responsible for high activity in the Pt/CoAl₂O₄/Al₂O₃ catalyst.     

Catalytic Activities of Al2O3-promoted NiSO4/TiO2 for Acid Catalysis

A series of catalysts, NiSO₄/Al₂O₃–TiO₂, for acid catalysis was prepared by the impregnation method, where support, Al₂O₃–TiO₂ was prepared by the coprecipitation method using a mixed aqueous solution of titanium tetrachloride and aluminum nitrate solution followed by adding an aqueous ammonia solution. The addition of nickel sulfate (or Al₂O₃) to TiO₂ shifted the phase transition of TiO₂ from amorphous to anatase to higher temperature because of the interaction between nickel sulfate (or Al₂O₃) and TiO₂. 15-NiSO₄/5-Al₂O₃–TiO₂ containing 15 wt% NiSO₄ and 5 mol% Al₂O₃, and calcined at 400°C exhibited maximum catalytic activities for both reactions, 2-propanol dehydration and cumene dealkylation. The catalytic activities for both reactions were correlated with the acidity of catalysts measured by the ammonia chemisorption method. The charge transfer from Ti atoms to the neighboring Al atoms strengthens the Al–O bond between Al and the surface sulfate species. The addition of Al₂O₃ up to 5 mol% enhanced the acidity, thermal property, and catalytic activities of NiSO₄/Al₂O₃–TiO₂ gradually due to the interaction between Al₂O₃ and TiO₂ and consequent formation of Al–O–Ti bond.