Electrophoretic deposition of TiO2 film on titanium foil for a flexible dye-sensitized solar cell

Electrophoretic deposition (EPD) method is employed to obtain mesoporous TiO₂ film on a titanium (Ti) foil; the film is then mechanically compressed and sintered at 350 °C before being subjected to dyeing. A comprehensive study was made on the mechanistic aspects of the EPD process. The dye-sensitized solar cell (DSSC) using the thus formed TiO₂ film rendered a power conversion efficiency (Eff.) of 6.5%. Effects of various compression pressures on the photovoltaic parameters and on other characteristic parameters of the pertinent DSSCs are studied. Electrochemical impedance spectroscopy (EIS) is applied for the first time, using a novel equivalent model, to study the impedance behavior of the DSSC with this type of TiO₂ film. We also obtain characteristic parameters of the TiO₂ photoanode by using EIS. The coordination number of the TiO₂ film, and the ratio of charge transfer resistances of electron recombination and electron transport are also obtained and analyzed. Moreover, we employ a multilayer approach and increase the film thickness to prepare TiO₂ films with the same coordination number and porosity; DSSCs using such TiO₂ films obtained from P90 and P25 rendered efficiencies of 6.5% and 5.24%, respectively. Scanning electron microscopy (SEM) micrographs are obtained to characterize the TiO₂ films formed by the EPD technique and laser-induced transient technique is used to estimate the electron lifetime in the TiO₂ films.     

Quasi solid state dye-sensitized solar cells with modified TiO2 photoelectrodes and triphenylamine-based dye

Quasi solid state dye-sensitized solar cells (DSSCs) have been fabricated with organic sol or TiCl₄ modified TiO₂ and porous TiO₂ photoanode and a triphenylamine-based dye (TPAR3) used as photosensitizer. Dark current measurements suggested that both modified TiO₂ photoelectrodes had significantly reduced the recombination rate of photoelectrons due to the reduced bare FTO surface in comparison to porous photoelectrode. The DSSC based on modified TiO₂ photoelectrodes showed improved photovoltaic parameters compared to the porous TiO₂ photoelectrode. The overall power conversion efficiency (PCE) is 3.27%, 4.73% and 6.8% for porous, TiCl₄ modified and sol modified TiO₂ photoelectrodes, respectively. The improved PCE with modified TiO₂ electrodes was attributed to the formation of a compact layer. This effectively improves adherence of TiO₂ to FTO surface, providing a larger TiO₂/FTO contact area and reducing the electron recombination by blocking the direct contact between redox electrolyte and the conductive FTO surface and enhances the electron collection efficiency.     

Fabrication of morphology controllable rutile TiO2 nanowire arrays by solvothermal route for dye-sensitized solar cells

Highly ordered, vertically oriented TiO₂ nanowire arrays (TNAs) are synthesized directly on transparent conducting substrate by solvothermal procedure without any template. The X-ray diffraction (XRD) pattern shows that TiO₂ array is in rutile phase growing along the (0 0 2) direction. The field-emission scanning electron microscopy (FE-SEM) images of the samples indicate that the TiO₂ array surface morphology and orientation are highly dependent on the synthesis conditions. In a typical condition of solvothermal at 180 °C for 2 h, the TNAs are composed of nanowires 10 ± 2 nm in width, and several nanowires bunch together to form a larger secondary structure of 60 ± 10 nm wide. Dye-sensitized solar cell (DSSC) assembled with the TNAs grown on the FTO glass as photoanode under illumination of simulated AM 1.5G solar light (100 mW cm⁻²) achieves an overall photoelectric conversion efficiency of 1.64%.     

Anodic TiO2 Nanotube Arrays for Dye-Sensitized Solar Cells Characterized by Electrochemical Impedance Spectroscopy

This paper reports on the microstructure of anodic titanium oxide (TiO₂) and its use in a dye-sensitized solar cell (DSSC) device. When voltages of 60 V were applied to titanium foil for 2 hr under 0.25 wt% NH₄F+ 2 vol% H₂O+C₂H₄(OH)₂, TiO₂ with a nanotube structure was formed. The film, which had a large surface area, was used as an electron transport film in the DSSC. The DSSC device had a short-circuit current density (J_sc) of 12.52 mA cm⁻², a fill factor (FF) of 0.65, an open-voltage (V_oc) of 0.77 V, and a photocurrent efficiency of 6.3% under 100% AM 1.5 light. The internal impedance values under 100%, 64%, 11%, and 0% (dark) AM 1.5 light intensities were measured and simulated using the electrical impedance spectroscopy (EIS) technique. The impedance characteristics of the DSSC device were simulated using inductors, resistors, and capacitors. The Ti/TiO₂, TiO₂/Electrolyte, electrolyte, and electrolyte/(Pt/ITO) interfaces were simulated using an RC parallel circuit, and the bulk materials, such as the Ti, ITO and conducting wire, were simulated using a series of resistors and inductors. The impedance of the bulk materials was simulated using L₀+R₀+R_b, the impedance of the working electrode was simulated using (C₁//R₁)//(R_a+(C₂//R₂), the electrolyte was simulated using C₃//R₃, and the counter electrode was simulated using C₄//R₄.     

Excellent antimicrobial properties of mesoporous anatase TiO2 and Ag/TiO2 composite films

Optically transparent, crack-free, mesoporous anatase TiO₂ thin films were fabricated. The Ag/TiO₂ composite films were prepared by incorporating Ag in the pores of TiO₂ films with an impregnation method via photoreduction. The as-prepared composite films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectronic spectra (XPS) and N₂ adsorption. The release behavior of silver ions in the mesoporous composite film was also studied. Moreover, the antimicrobial behaviors of the mesoporous film were also investigated by confocal laser scanning microscopy. The antibacterial activities of the composite films were studied by a fluorescence label method using Escherichia coli (E. coli) as a model. The as-prepared mesoporous TiO₂ films showed much higher antimicrobial efficiency than that of glass and commercial P25 TiO₂ spinning film. The facts would result from the high surface area, small crystal size and more active sites for the mesoporous catalysis. After the doping of Ag, a significant improvement for the antimicrobial ability was obtained. To elucidate the roles of the membrane photocatalyst and the doped silver in the antimicrobial activity, cells from a silver-resistant E. coli were used. These results indicated that Ag nanoparticles in the mesoporous were not only an antimicrobial but also an intensifier for photocatalysis. The as-prepared mesoporous composite film is promising in application of photocatalysis, antimicrobial and self-clean technologies.     

Photocatalytic properties of TiO2 sol-gel modified nanocomposite films

TiO₂ nanocomposite films with different concentrations of TiO₂ MT-150A nanoparticles were immobilized on glass substrates using a dip coating process. The crystalline structure and surface chemical state of nanocomposite film properties were examined by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), respectively. The specific surface area and morphology of TiO₂ MT-150A nanoparticles were evaluated by the BET method and Field Emission Scanning Electron Microscopy (FE-SEM). The photocatalytic activities of films were evaluated by the methyl orange decoloring rate. XPS measurements showed that the oxygen amount (%) was related to the film composition. The composite film with 10 g/L MT-150A loading yielded the highest amount of surface oxygen (26.82%) and TiO₂ rutile showed the lowest amount of surface oxygen (13.67%) in the form of surface hydroxyl groups. The remaining oxygen was identified as lattice oxygen. In addition, the nanocomposite film with 10 g/L MT-150A loading yielded the highest photocatalytic activity.     

TiO2, TiO2/Ag and TiO2/Au photocatalysts prepared by spray pyrolysis

TiO₂, TiO₂/Ag and TiO₂/Au photocatalysts exhibiting a hollow spherical morphology were prepared by spray pyrolysis of aqueous solutions of titanium citrate complex and titanium oxalate precursors in one-step. Effects of precursor concentration and spray pyrolysis temperature were investigated. By subsequent heat treatment, photocatalysts with phase compositions from 10 to 100% rutile and crystallite sizes from 12 to 120 nm were obtained. A correlation between precursor concentration and size of the hollow spherical agglomerates obtained during spray pyrolysis was established. The anatase to rutile transformation was enhanced with metal incorporations and increased precursor concentration. The photocatalytic activity was evaluated by oxidation of methylene blue under UV-irradiation. As-prepared TiO₂ particles with large amounts of amorphous phase and organic residuals showed similar photocatalytic activity as the commercial Degussa P25. The metal incorporated samples showed comparable photocatalytic activity to the pure TiO₂ photocatalysts.     

Synthesis and electrochemical properties of CeO2 nanoparticle modified TiO2 nanotube arrays

In this paper, a cerium dioxide (CeO₂) modified titanium dioxide (TiO₂) nanotube array film was fabricated by electrodeposition of CeO₂ nanoparticles onto an anodized TiO₂ nanotube array. The structural investigation by X-ray diffraction, scanning electron microscopy and transmission electron microscopy indicated that the CeO₂ nanoparticles grew uniformly on the walls of the TiO₂ nanotubes. The composite was composed of cubic-phase CeO₂ crystallites and anatase-phase TiO₂ after annealing at 450 °C. The cyclic voltammetry and chronoamperometric charge/discharge measurement results indicated that the CeO₂ modification obviously increased the charge storage capacity of the TiO₂ nanotubes. The charge transfer process at the surface, that is, the pseudocapacitance, was the dominate mechanism of the charge storage in CeO₂-modified TiO₂ nanotubes. The greater number of surface active sites resulting from uniform application of the CeO₂ nanoparticles to the well-aligned TiO₂ nanotubes contributed to the enhancement of the charge storage density.     

Enhancing the performance of dye-sensitized solar cells based on an organic dye by incorporating TiO2 nanotube in a TiO2 nanoparticle film

The photoelectrochemical properties of a high molar extinction coefficient charge transfer organic dye containing thienylfluorene segment called FL, and the effect of incorporating TiO₂ nanotube (TiNT) in TiO₂ nanoparticle film along with the above dye on the photovoltaic performance of dye-sensitized solar cells (DSSCs) were investigated. The influence of soaking time of the TiO₂ electrode in dye solution and the effect of varying its concentration, on the solar cell efficiency was also studied. Cyclic voltammetric (CV) analysis revealed the linear relationship between the anodic peak current and the scan rate, indicating a surface-confined diffusion process.The surface morphology of TiNT was characterized using SEM, TEM and XRD. The open-circuit voltage (V_OC) of the DSSC increased with the increase in the wt% of TiNT and shows optimal value at about 5 wt%, which is correlated with the suppression of the electron recombination as found out from the electron lifetime studies.The electrochemical impedance spectroscopy (EIS) technique was employed to quantify the charge transport resistance (R_ct) and electron lifetime under different ratios of the TiNT/nanoparticle. The electron lifetimes of the DSSCs based on FL and N3 dye were very close to one another and the DSSC based on the FL showed respectable photovoltaic performance of ca. 7.8% under the light intensity of 100 mW cm⁻² (AM 1.5G).     

Effect of gold nanoparticles on the performances of TiO2 dye-sensitised solar cell

TiO₂ blended with Au nanoparticles (NP) was hydrothermally synthesised under controlled conditions and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM). The dye-sensitised solar cells (DSSC) were characterized using the UV–vis spectrometry and current-voltage (I-V) testing. The performance of TiO₂-Au DSSC is significantly higher than TiO₂ DSSC. The addition of Au NPs improves the light harvesting efficiency of the DSSC, thus improving the short circuit current density, J_sc, and the conversion efficiency of the DSSC. The excitation of localised surface plasmon resonance of the Au nanoparticles utilised the strong local field enhancement around the Au NPs to increase the absorption in the surrounding TiO₂ layer. It was demonstrated that the power conversion efficiency of the DSSC was improved by 28% with the addition of Au NPs.     

Aerosol assisted chemical vapour deposited (AACVD) of TiO2 thin film as compact layer for dye-sensitised solar cell

Compact TiO₂ has been introduced onto the surface of an indium tin oxide glass slide (ITO), using an aerosol-assisted chemical vapour deposition method. This serves as a blocking layer for a dye-sensitised solar cell (DSSC). The thickness of the compact TiO₂ could be controlled by deposition time. X-ray diffraction and Raman spectroscopy analyses reveal that the compact TiO₂ is made up of mixed anatase and rutile phases. The field emission scanning electron microscopy image displays a pyramidal morphology of the compact TiO₂. A layer of P25 paste was then smeared onto the compact TiO₂-modified ITO, using the doctor's blade method. A post-treatment procedure was applied to remove the contaminants from the prepared hybrid film, by immersing in a hydrochloric acid solution. The photoelectrochemical measurements and J–V characterisation of the hybrid film show an approximately fourfold increase in photocurrent density generation (114.22 µA/cm²), and approximately 25% enhancement of DSSC conversion efficiency (4.63%), compared to the acid-treated P25 paste alone (3.68%).     

The synthesis and morphology characteristic study of BAO-ODPA polyimide/TiO2 nano hybrid films

Hybrid nanocomposite films of titanium dioxide (TiO₂) in polyimide (PI) from 2,5-bis(4-aminophenyl)-1,3,4-oxadiazole (BAO) and 4,4′-oxydiphthalic anhydride (ODPA) have been successfully fabricated by an in situ sol-gel process. These nanocomposite films exhibit fair good optical transparency up to 40 wt% of TiO₂ content. X-ray diffraction spectroscopy shows three sharp peaks in pure BAO-ODPA PI. It results from the intermolecular regularity. However, the intermolecular regularity in the hybrid film is disrupted by the introduction of TiO₂ nanoparticles with no sharp peak in XRD spectra. Fourier transform infrared (FTIR) and X-ray photoelectron spectroscopy (XPS) results confirm the formation of TiO₂ particles in PI matrix. The surface Ti content is much lower than the theoretical bulk content in all hybrid films. The ratio of the former to the latter increases with the TiO₂ content and levels off at TiO₂ wt%≥20. Transmission electron microscope (TEM) images show that the TiO₂ phase is well dispersed in the polymer matrix. The size of the TiO₂ phase increases from 10 to 40 nm when the TiO₂ content is 5-30 wt%, respectively.     

Chitosan/TiO2 nanocomposite pervaporation membranes for ethanol dehydration

Novel chitosan/titanium dioxide (CS/TiO₂) nanocomposite membranes were prepared using tetrabutyl titanate (TBT) as precursor and acetyl acetone as chelating agent by in situ sol-gel process, and characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and thermogravimetry (TG). The characterization results demonstrated that nano-sized TiO₂ particles dispersed homogeneously within the CS matrix, which could be assigned to the hydrogen and titanoxane bonds formed between CS and TiO₂. Moreover, the pervaporation performance of these membranes was investigated using the separation of ethanol-water mixture as model system. Compared with CS/TiO₂ hybrid membranes prepared by blending method, most of CS/TiO₂ nanocomposite membranes prepared by in situ sol-gel process exhibited higher permeation flux and separation factor under the identical conditions. Among all the prepared membranes, CS/TiO₂ nanocomposite membrane containing 6 wt% TiO₂ exhibited the best pervaporation performance, whose averaged permeation flux and separation factor were 0.340 kg m⁻² h⁻¹ and 196 for 90 wt% aqueous solution of ethanol at 80 °C, respectively.     

Photovoltaic efficiency on dye-sensitized solar cells (DSSC) assembled using Ga-incorporated TiO2 materials

This study examined the photoelectric conversion efficiency of DSSC (dye-sensitized solar cell) when nanometer sized Ga (0.25, 0.50, and 1.00 mol%)–TiO₂ prepared using a hydrothermal method was employed as a working electrode material. The particle sizes observed in the transmission electron microscopy images were <20 nm in all samples. However, with increasing Ga concentration, the size increased and the shapes transformed to a stick form. The absorption band was slightly blue-shifted upon the incorporation of gallium ions, but the intensity of the photoluminescence (PL) curves of the Ga-incorporated TiO₂ was significantly smaller, with the smallest case being the 0.50 mol% Ga–TiO_2, which was related to recombination between the excited electrons and holes. When Ga–TiO₂ was applied in DSSC, the energy conversion efficiency was enhanced considerably compared to that using pure TiO₂; it was approximately 4.57% with the N3 dye under 100 mW/cm² of simulated sunlight. These results are in agreement with an electrostatic force microscopy (EFM) study showing that the electrons were transferred rapidly to the surface of Ga–TiO₂ film, compared with that on a pure TiO₂ film.     

Properties of sol-gel SnO2/TiO2 electrodes and their photoelectrocatalytic activities under UV and visible light illumination

A visible light active binary SnO₂-TiO₂ composite was successfully prepared by a sol-gel method and deposited on Ti sheet as a photoanode to degrade orange II dye. Titanium and SnO₂ can promote the development of rutile phase of TiO₂ and inhibit the formation of anatase phase of TiO₂. Formation of SnO₂ crystalline is insignificant even when the calcination temperature increases to 700 °C. Heterogenized interface between SnO₂ and TiO₂ inhibits growth of TiO₂ linkage and leads to the particle-filled surface morphology of SnO₂-containing films. The carbonaceous, Ti-O-C bonds and Ti³⁺ species are likely to account for the photoabsorption and photoelectrocatalytic (PEC) activity under visible light illumination. The electrode with 30% SnO₂ exhibits higher photocurrent when compared with those in the region of 0-50%. The 600 °C-calcined SnO₂-TiO₂ electrode indicates higher activity when compared with those at 400, 500, 700 and 800 °C. PEC degradation of orange II follows the Langmuir-Hinshelwood model and takes place much effectively in a solution of pH 3.0 than those in pH 7.0 and pH 11.0.     

Efficiency improvement of dye-sensitized solar cells based on electrodeposited TiO2 films by low temperature post-treatment

Porous crystalline TiO₂ films can be prepared at low temperatures (80 °C) by surfactant-assisted electrodeposition from TiCl₃ solution. Nevertheless, up to now calcination at high temperatures (typically 450 °C) was still necessary to establish a good performance of these films in dye-sensitized solar cells (DSSC). With this study we report that water vapour treatment at much lower temperatures (150 °C) for 1 week improves the performance of the films in DSSC to the same degree as calcination although the overall crystallinity remains lower. Reason for the good efficiency is that the porous structure stays intact and thus the dye molecules can be better adsorbed. Avoiding high temperatures during the preparation process of TiO₂ films for the application in DSSC enables the use of polymer substrates for the fabrication of flexible solar cells.     

Influence of TiO2 and CeO2 on the hydrogenation activity of bulk Ni2P

TiO₂- and CeO₂-promoted bulk Ni₂P catalysts were prepared by impregnation and in-situ H₂ temperature-programmed reduction method. The prepared catalysts were characterized by XRD and XPS. The hydrogenation activities of the catalysts were studied using 1.5 wt.% 1-heptene in toluene and 1.0 wt.% phenylacetylene in ethanol as the model feeds. The results indicate that bulk Ni₂P possesses low hydrogenation activity but is tunable by simply controlling the content of the additives (TiO₂ or CeO₂), suggesting that TiO₂ and CeO₂ are effective promoters to enhance the hydrogenation activity of Ni₂P.     

Mn2O3/TiO2 nanofibers with broad-spectrum antibiotics effect and photocatalytic activity for preliminary stage of water desalination

Composite nanofibers consisting of Mn₂O₃ and TiO₂ were prepared by the electrospinning process, and tested as Gram-class-independent antibacterial agent and photocatalyst for organic pollutants degradation. Initially, electrospinning of a sol–gel consisting of titanium isopropoxide, manganese acetate tetrahydrate and poly(vinyl pyrrolidone) was used to produce hybrid polymeric nanofibers. Calcination of the obtained nanofibers in air at 650 °C led to produce good morphology Mn₂O₃/TiO₂ nanofibers. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were employed to characterize the as-spun nanofibers and the calcined product. X-ray powder diffractometry (XRD) analysis was also used to characterize the chemical composition and the crystallographic structure of the sintered nanofibers. The antibacterial activity of Mn₂O₃/TiO₂ nanofibers against Gram negative and Gram positive bacteria was investigated by calculating the minimum inhibitory concentration after treatment with the nanofibers. Investigations revealed that the lowest concentration of Mn₂O₃/TiO₂ nanofibers solution inhibiting the growth of Staphylococcus aureus ATCC 29231 and Escherichia coli ATCC 52922 strains is 0.4 and 0.8 μg/ml, respectively. Incorporation of Mn₂O₃ significantly improved the photodegradation of methylene blue (MB) dye under the visible light irradiation due to enhancing rutile phase formation in the TiO₂ nanofibers matrix.     

Tertiary hierarchically structured TiO2 for CdS quantum-dot-sensitized solar cells

A tertiary hierarchically structured mesoporous spherical TiO₂ (with a diameter of 1190 ± 60 nm) was synthesized by combining the sol–gel and the subsequent solvothermal treatment, and applied to CdS quantum-dot-sensitized solar cells (QDSSCs). This mesoporous spherical (MS) TiO₂ offers a high surface area (76.02 m² g⁻¹), a high internal reflectance in the visible region and a pore accessibility. A conversion efficiency of 1.9% was achieved by CdS QDSSCs composed of the MS TiO₂ photoanode, which corresponds to ∼58% improvement as compared with the values obtained from the conventional devices made with 20-nm-sized nanocrystalline TiO₂ under AM 1.5 illumination of 100 mW cm⁻². Thus, the MS TiO₂ can be a promising candidate for the photoanode material of QDSSCs.