Pulsed electrodeposition of p-type CuInSe2 thin films

CuInSe₂ thin films have been electrodeposited on conductive glass using cyclic pulse electrodeposition. One cycle consists of consequtively applying potentials E₁ and E₂, each during 10 s and a total of 90 cycles are applied. E₁ is chosen between −0.7 and −0.9 V_SCE while E₂ is fixed at −0.1 V_SCE. The films are annealed in argon and then etched in KCN solution to eliminate remnant secondary phases. The material is characterized employing grazing incident X-rays diffraction, Raman spectroscopy, scanning electron microscopy and energy dispersive scanning spectroscopy. The presence of secondary phases seems to be reduced when compared to films prepared at fixed potentials. The films are crystalline and the overall quality improves by annealing in Ar. Photoelectrochemical tests, Mott–Schottky plots and I–V curves confirm p-type conduction. The diffusion regime imposed by the potential pulses could be responsible for the different morphology and composition of samples prepared with pulsed and potentiostatic electrodeposition.     

The effect of co-doping with MgO and Yb2O3 on the structure and electrical conductivity of the Sm2Zr2O7 pyrochlore

SmYb_1−xMg_xZr₂O_7−x/2 (0 ≤ x ≤ 0.15) ceramics are pressureless-sintered at 1973 K for 10 h in air. The structure and electrical conductivity of SmYb_1−xMg_xZr₂O_7−x/2 ceramics are investigated by the X-ray diffraction, scanning electron microscopy and impedance spectroscopy measurements. SmYb_1−xMg_xZr₂O_7−x/2 ceramics exhibit a defect fluorite-type structure. The measured electrical conductivities of SmYb_1−xMg_xZr₂O_7−x/2 ceramics obey the Arrhenius relation, and electrical conductivity of each composition increases with increasing temperature from 673 to 1173 K. At identical temperature levels, the electrical conductivity of SmYb_1−xMg_xZr₂O_7−x/2 ceramics gradually increases with increasing magnesia content. SmYb_1−xMg_xZr₂O_7−x/2 ceramics are oxide-ion conductors in the oxygen partial pressure range of 1.0 × 10⁻⁴ to 1.0 atm at all test temperature levels. The electrical conductivity obtained in SmYb_1−xMg_xZr₂O_7−x/2 ceramics reaches the highest value of 2.72 × 10⁻³ S cm⁻¹ at 1173 K for the SmYb_0.85Mg_0.15Zr₂O_6.925 ceramic.     

Electrochemical performance of LiFePO4 thin films with different morphology and crystallinity

LiFePO₄ thin films have been prepared by pulsed laser deposition method on titanium substrates. The influence of the deposition parameters, e.g. substrate temperature, ambient argon pressure, and post-annealing on the crystallinity and morphology of as-deposited thin films are investigated. Well-crystallized pure olivine-phase is obtained under optimized deposition condition (20–30 Pa, 500 °C). It shows a high electrochemical activity (83% theoretical capacity) at low current density (0.33 μA cm⁻², 1/20 C) and elevated testing temperature (45 °C). Moderate post-annealing treatment can enhance the utilization of the films further. The deposition of the film at a too high temperature or post-annealing for too long time could introduce Fe³⁺ impurities, i.e., Li₃Fe₂(PO₄)₃ and Fe₄(P₂O₇)₃, which can be easily detected by extending the electrochemical test voltage down to 2.5 V.     

Preparation and electrochemical properties of Cr-doped Li9V3(P2O7)3(PO4)2 as cathode materials for lithium-ion batteries

Cr-doped Li₉V_3−xCr_x(P₂O₇)₃(PO₄)₂ (x = 0.0–0.5) compounds have been prepared using sol–gel method. The Rietveld refinement results indicate that single-phase Li₉V_3−xCr_x(P₂O₇)₃(PO₄)₂ (x = 0.0–0.5) with trigonal structure can be obtained. Although the initial specific capacity decreased with Cr content at a lower current rate, both cycle performance and rate capability have excited improvement with moderate Cr-doping content. Li₉V_2.8Cr_0.2(P₂O₇)₃(PO₄)₂ compound presents the good electrochemical rate and cyclic ability. The enhancement of rate and cyclic capability may be attributed to the optimizing particle size, morphologies, and structural stability during the proper amount of Cr-doping (x = 0.2) in V sites.     

Studies on electrical properties of La0.8Sr0.2Ga0.8Mg0.2O2.80 (LSGM) and LSGM-SrSn1−xFexO3 (x = 0.8; 0.9) composites and their chemical reactivity

We report the electrical conductivity properties of solid-state synthesized perovskite-like La_0.8Sr_0.2Ga_0.8Mg_0.2O_2.80 (LSGM) and LSGM-SrSn_1−xFe_xO₃ (x = 0.8; 0.9) composites. LSGM exhibits both bulk and grain-boundary contribution in the ac impedance plots. The grain-boundary conductivity (σ_gb) is slightly (≤half-order of magnitude) higher than that of the bulk oxide ion conductivity (σ_bulk). Powder XRD study reveals that no chemical reaction occurs between LSGM and SrSn_1−xFe_xO₃ (1:1 wt.%) at 1000 °C (48 h) and forms a single-phase perovskite-like compound at 1300 °C (48 h) in air, while in hydrogen atmosphere, at 800 °C for 48 h, a growth of LaSrGaO₄ and LaSrGa₃O₇ impurity phases and formation of metallic Fe was observed. The LSGM-SrSn_1−xFe_xO₃ (x = 0.8; 0.9) composites show a single or part of semicircle in air at low-temperature regime. The electrical conductivity of the composites were found to be much higher compared to pure LSGM and lower about an order of magnitude than those of pure Sn-doped SrFeO₃ perovskite.     

The influence of preparation conditions on electrochemical properties of LiNi0.5Mn1.5O4 thin film electrodes by PLD

LiNi_0.5Mn_1.5O₄ thin films were prepared by pulsed laser deposition (PLD) on stainless steel substrates. The growth of the films has been studied as a function of substrate temperature and oxygen partial pressure in deposition, using X-ray diffraction (XRD) and field-emission scanning electron microscopy (FESEM). Electrochemical properties of LiNi_0.5Mn_1.5O₄ thin film cathodes were investigated using cyclic voltammetry and galvanostatic charge/discharge against a lithium anode. The initial capacity and capacity retention of the films are highly dependent on the crystallinity and purity of the films. LiNi_0.5Mn_1.5O₄ thin films grown at 600 °C in an oxygen partial pressure of 200 mTorr are well crystallized with high purity, exhibiting excellent capacity retention between 3 and 5 V with a LiPF₆-based electrolyte.     

Synthesis and electrochemical characterization of LiCoxMn1−xPO4/C nanocomposites

LiCo_xMn_1−xPO₄/C nanocomposites (0 ≤ x ≤ 1.0) were prepared by a combination of spray pyrolysis at 300 °C and wet ball-milling followed by heat treatment at 500 °C for 4 h in 3% H₂ + N₂ atmosphere. X-ray diffraction analysis indicated that all samples had the single phase olivine structures indexed by orthorhombic Pmna. The lattice parameters linearly decreased with increasing cobalt content, which confirmed the existence of solid solutions. It was clearly seen from the scanning electron microscopy observation that the LiCo_xMn_1−xPO₄/C samples were agglomerates with approximately 100 nm primary particles. The LiCo_xMn_1−xPO₄/C nanocomposites were used as cathode materials for lithium batteries, and electrochemical performance was comparatively investigated with cyclic voltammetry and galvanostatic charge–discharge test using the Li?1 M LiPF₆ in EC:DMC = 1:1?LiCo_xMn_1−xPO₄/C cells at room temperature. The cells at 0.05 C charge–discharge rate delivered first discharge capacities of 165 mAh g⁻¹ (96% of theoretical capacity) at x = 0, 136 mAh g⁻¹ at x = 0.2, 132 mAh g⁻¹ at x = 0.5, 125 mAh g⁻¹ at x = 0.8 and 132 mAh g⁻¹ (79% of theoretical capacity) at x = 1.0, respectively. While the first discharge capacity increased with the cobalt content at high charge–discharge rates more than 0.5 C due to higher electronic conductivity of LiCoPO₄ in comparison with LiMnPO₄, the cycleability of cell became worse with increasing the amount of cobalt. The existence of Mn²⁺ seemed to enhance the cycleability of LiCo_xMn_1−xPO₄/C nanocomposite cathode.     

High rate capability and long-term cyclability of Li4Ti4.9V0.1O12 as anode material in lithium ion battery

Li₄Ti_4.9V_0.1O₁₂ nanometric powders were synthesized via a facile solid-state reaction method under inert atmosphere. XRD analyses demonstrated that the V-ions successfully entered the structure of cubic spinel-type Li₄Ti₅O₁₂ (LTO), reduced the lattice parameter and no impurities appeared. Compared with the pristine LTO, the electronic conductivity of Li₄Ti_4.9V_0.1O₁₂ powders is as high as 2.9 × 10⁻¹ S cm⁻¹, which should be attributed to the transformation of some Ti³⁺ from Ti⁴⁺ induced by the efficient V-ions doping and the deficient oxygen condition. Meanwhile, the results of XPS and EDS further proved the coexistence of V⁵⁺ and Ti³⁺ ions. This mixed Ti⁴⁺/Ti³⁺ ions can remarkably improve its cycle stability at high discharge–charge rates because of the enhancement of the electronic conductivity. The images of SEM showed that Li₄Ti_4.9V_0.1O₁₂ powders have smaller particles and narrower particle size distribution under 330 nm. And EIS indicates that Li₄Ti_4.9V_0.1O₁₂ has a faster lithium-ion diffusivity than LTO. Between 1.0 and 2.5 V, the electrochemical performance, especially at high rates, is excellent. The discharge capacities are as high as 166 mAh g⁻¹ at 0.5C and 117.3 mAh g⁻¹ at 5C. At the rate of 2C, it exhibits a long-term cyclability, retaining over 97.9% of its initial discharge capacity beyond 1713 cycles. These outstanding electrochemical performances should be ascribed to its nanometric particle size and high conductivity (both electron and lithium ion). Therefore, the as-prepared material is promising for such extensive applications as plug-in hybrid electric vehicles and electric vehicles.     

High temperature phase stabilities and electrochemical properties of InBaCo4−xZnxO7 cathodes for intermediate temperature solid oxide fuel cells

InBaCo_4−xZn_xO₇ oxides have been synthesized and characterized as cathode materials for intermediate temperature solid oxide fuel cells (IT-SOFC). The effect of Zn substitution for Co on the structure, phase stability, thermal expansion, and electrochemical properties of the InBaCo_4−xZn_xO₇ has been investigated. The increase in the Zn content from x = 1 to 1.5 improves the high temperature phase stability at 600 °C and 700 °C for 100 h, and chemical stability against a Gd_0.2Ce_0.8O_1.9 (GDC) electrolyte. Thermal expansion coefficient (TEC) values of the InBaCo_4−xZn_xO₇ (x = 1, 1.5, 2) specimens were determined to be 8.6 × 10⁻⁶ to 9.6 × 10⁻⁶/°C in the range of 80–900 °C, which provides good thermal expansion compatibility with the standard SOFC electrolyte materials. The InBaCo_4−xZn_xO₇ + GDC (50:50 wt.%) composite cathodes exhibit improved cathode performances compared to those obtained from the simple InBaCo_4−xZn_xO₇ cathodes due to the extended triple-phase boundary (TPB) and enhanced oxide-ion conductivity through the GDC portion in the composites.     

One-step electrochemical preparation of the ternary (BixSb1−x)2Te3 thin films on Au(1 1 1): Composition-dependent growth and characterization studies

This study reports on the synthesis of ternary semiconductor (Bi_xSb_1−x)₂Te₃ thin films on Au(1 1 1) using a practical electrochemical method, based on the simultaneous underpotential deposition (UPD) of Bi, Sb and Te from the same solution containing Bi³⁺, SbO⁺, and HTeO₂⁺ at a constant potential. The thin films are characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), energy dispersive spectroscopy (EDS) and reflection absorption-FTIR (RA-FTIR) to determine structural, morphological, compositional and optic properties. The ternary thin films of (Bi_xSb_1−x)₂Te₃ with various compositions (0.0 ≤ x ≤ 1.0) are highly crystalline and have a kinetically preferred orientation at (0 1 5) for hexagonal crystal structure. AFM images show uniform morphology with hexagonal-shaped crystals deposited over the entire gold substrate. The structure and composition analyses reveal that the thin films are pure phase with corresponding atomic ratios. The optical studies show that the band gap of (Bi_xSb_1−x)₂Te₃ thin films could be tuned from 0.17 eV to 0.29 eV as a function of composition.     

Study of carbon-supported IrO2 and RuO2 for use in the hydrogen evolution reaction in a solid polymer electrolyte electrolyzer

Carbon-supported IrO₂ and RuO₂ were prepared using an incipient wetness method and were then calcinated at various temperatures. IrO₂/C and RuO₂/C are less expensive than the conventional Pt/C material and more stable than metal Ni in an acidic electrolyte. Moreover, IrO₂/C and RuO₂/C are not influenced by under potential deposition (UPD) and show lower sensitivity to poisoning by Ni or Fe impurities. The physical properties of IrO₂/C and RuO₂/C were investigated via XRD and TEM. Cyclic voltammograms (CV) and Tafel plots were used to provide information regarding surface redox reaction and electrocatalytic activity. The activity and durability of IrO₂/C and RuO₂/C were studied after prolonged potential cycling between −0.3 and 0.3 V_SCE. After comparison of Tafel plots of Pt/C and IrO₂/C after activation, it was observed that they have similar electrocatalytic activities in a hydrogen evolution reaction (HER). A single cell test with solid polymer electrolyte (SPE) proved that the performance of IrO₂/C (0.5 mg cm⁻²) was similar to that of Pt/C (0.5 mg cm⁻²).     

Synthesis and microstructure of (LaSr)MnO3 and (LaSr)FeO3 ceramics by a reaction-sintering process

(La_xSr_1−x)MnO₃ (LSMO) and (La_xSr_1−x)FeO₃ (LSFO) (x = 0.2–0.4) ceramics prepared by a simple and effective reaction-sintering process were investigated. Without any calcination involved, La₂O₃ and SrCO₃ were mixed with MnO₂ (LSMO) or Fe₂O₃ (LSFO) then pressed and sintered directly. LSMO and LSFO ceramics were obtained after 2 and 4 h sintering at 1350–1400 and 1200–1280 °C, respectively. Grain size decreased as La content increased in LSMO and LSFO ceramics.     

Effect of TiO2 supporting layer on Fe2O3 photoanode for efficient water splitting

For an electrochemical water splitting system, titanate nanotubular particles with a thickness of ∼700 nm produced by a hydrothermal process were repetitively coated on fluorine-doped tin oxide (FTO) glass via layer-by-layer self-assembly method. The obtained titanate/FTO films were dipped in aqueous Fe solution, followed by heat treatment for crystallization at 500 °C for 10 min in air. The UV–vis absorbance of the Fe-oxide/titanate/FTO film showed a red-shifted spectrum compared with the TiO₂/FTO coated film; this red shift was achieved by the formation of thin hematite-Fe₂O₃ and anatase-TiO₂ phases verified using X-ray diffraction and Raman results. The cyclic voltammetry results of the Fe₂O₃/TiO₂/FTO films showed distinct reversible cycle characteristics with large oxidation–reduction peaks with low onset voltage of I–V characteristics under UV–vis light illumination. The prepared Fe₂O₃/TiO₂/FTO film showed much higher photocurrent densities for more efficient water splitting under UV–vis light illumination than did the Fe₂O₃/FTO film. Its maximum photocurrent was almost 3.5 times higher than that obtained with Fe₂O₃/FTO film because of the easy electron collection in the current collector. The large current collection was due to the existence of a TiO₂ base layer beneath the Fe₂O₃ layer.     

Synthesis and electrochemical properties of Co-doped Li3V2(PO4)3 cathode materials for lithium-ion batteries

Co-doped Li₃V_2−xCo_x(PO₄)₃/C (x = 0.00, 0.03, 0.05, 0.10, 0.13 or 0.15) compounds were prepared via a solid-state reaction. The Rietveld refinement results indicated that single-phase Li₃V_2−xCo_x(PO₄)₃/C (0 ≤ x ≤ 0.15) with a monoclinic structure was obtained. The X-ray photoelectron spectroscopy (XPS) analysis revealed that the cobalt is present in the +2 oxidation state in Li₃V_2−xCo_x(PO₄)₃. XPS studies also revealed that V⁴⁺ and V³⁺ ions were present in the Co²⁺-doped system. The initial specific capacity decreased as the Co-doping content increased, increasing monotonically with Co content for x > 0.10. Differential capacity curves of Li₃V_2−xCo_x(PO₄)₃/C compounds showed that the voltage peaks associated with the extraction of three Li⁺ ions shifted to higher voltages with an increase in Co content, and when the Co²⁺-doping content reached 0.15, the peak positions returned to those of the unsubstituted Li₃V₂(PO₄)₃ phase. For the Li₃V_1.85Co_0.15(PO₄)₃/C compound, the initial capacity was 163.3 mAh/g (109.4% of the initial capacity of the undoped Li₃V₂(PO₄)₃) and 73.4% capacity retention was observed after 50 cycles at a 0.1 C charge/discharge rate. The doping of Co²⁺into V sites should be favorable for the structural stability of Li₃V_2−xCo_x(PO₄)₃/C compounds and so moderate the volume changes (expansion/contraction) seen during the reversible Li⁺ extraction/insertion, thus resulting in the improvement of cell cycling ability.     

Electrical properties of V2O5–WO3/TiO2 EUROCAT catalysts evidence for redox process in selective catalytic reduction (SCR) deNOx reaction

Electrical conductivity measurements on EUROCAT V₂O₅–WO₃/TiO₂ catalyst and on its precursor without vanadia were performed at 300°C under pure oxygen to characterize the samples, under NO and under NH₃ to determine the mode of reactivity of these reactants and under two reaction mixtures ((i) 2000 ppm NO + 2000 ppm NH₃ without O₂, and (ii) 2000 ppm NO + 2000 ppm NH₃ + 500 ppm O₂) to put in evidence redox processes in SCR deNO_x reaction.It was first demonstrated that titania support contains certain amounts of dissolved W⁶⁺ and V⁵⁺ ions, whose dissolution in the lattice of titania creates an n-type doping effect. Electrical conductivity revealed that the so-called reference pure titania monolith was highly doped by heterovalent cations whose valency was higher than +4. Subsequent chemical analyses revealed that so-called pure titania reference catalyst was actually the WO₃/TiO₂ precursor of V₂O₅–WO₃/TiO₂ EUROCAT catalyst. It contained an average amount of 0.37 at.% W⁶⁺dissolved in titania, i.e. 1.07 × 10²⁰ W⁶⁺ cations dissolved/cm³ of titania. For the fresh catalyst, the mean amounts of W⁶⁺ and V⁵⁺ ions dissolved in titania were found to be equal to 1.07 × 10²⁰ and 4.47 × 10²⁰ cm⁻³, respectively. For the used catalyst, the mean amounts of W⁶⁺ and V⁵⁺ ions dissolved were found to be equal to 1.07 × 10²⁰ and 7.42 × 10²⁰ cm⁻³, respectively. Since fresh and used catalysts have similar compositions and similar catalytic behaviours, the only manifestation of ageing was a supplementary progressive dissolution of 2.9 × 10²⁰ additional V⁵⁺ cations in titania.After a prompt removal of oxygen, it appeared that NO alone has an electron acceptor character, linked to its possible ionosorption as NO⁻ and to the filling of anionic vacancies, mostly present on vanadia. Ammonia had a strong reducing behaviour with the formation of singly ionized vacancies. A subsequent introduction of NO indicated a donor character of this molecule, in opposition to its first adsorption. This was ascribed to its reaction with previously adsorbed ammonia strongly bound to acidic sites. Under NO + NH₃ reaction mixture in the absence of oxygen, the increase of electrical conductivity was ascribed to the formation of anionic vacancies, mainly on vanadia, created by dehydroxylation and dehydration of the surface. These anionic vacancies were initially subsequently filled by the oxygen atom of NO. N^o atoms, resulting from the dissociation of NO and from ammonia dehydrogenation, recombined into dinitrogen molecules. The reaction corresponded to

Full-size image

. In the presence of oxygen, NO did not exhibit anymore its electron acceptor character, since the filling of anionic vacancies was performed by oxygen from the gas phase. NO reacted directly with ammonia strongly bound on acidic sites. A tentative redox mechanism was proposed for both cases.     

Spontaneously ordered TiO2 nanostructures

Titanium dioxide thin films were deposited on quartz substrates kept at different O₂ pressures using pulsed laser deposition technique. The effects of reactive atmosphere and annealing temperature on the structural, morphological, electrical and optical properties of the films are discussed. Growth of films with morphology consisting of spontaneously ordered nanostructures is reported. The films growth under an oxygen partial pressure of 3 × 10⁻⁴ Pa consist in nanoislands with voids in between them whereas the film growth under an oxygen partial pressure of 1 × 10⁻⁴ Pa, after having being subjected to annealing at 500 °C, consists in nanosized elongated grains uniformly distributed all over the surface. The growth of nanocrystallites with the increase in annealing temperature is explained on the basis of the critical nuclei-size model.     

Electrical properties and AC degradation characteristics of low voltage ZnO varistors doped with Nd2O3

The electrical properties and degradation characteristics of low voltage ZnO varistors were investigated as a function of Nd₂O₃ content. The varistor ceramics with 0.03 mol% Nd₂O₃ sintered at 1250 °C were far more densified than those with 0.06, 0.09 and 0.12 mol% Nd₂O₃. The addition of Nd₂O₃ to the low voltage ZnO varistors greatly improved the current–voltage characteristics; the nonlinear coefficient of varistors increase from 12.2 to 34.6 with increasing Nd₂O₃ content. The samples with 0.03 mol% Nd₂O₃ showed excellent stability due to high density and relatively good V–I characteristics, with the nonlinear coefficient of 22.5 and the leakage current of 9.6 μA. Their variation rate of varistor voltage and nonlinear coefficient and leakage current were −4.7%, −5.4%, 18.3%, respectively, under AC degradation stress (1.0 V_1 mA/125 °C/24 h).     

Nanocomposite Fe2O3-Se as a new lithium storage material

The electrochemical properties of nanocomposite Fe₂O₃-Se thin film prepared by pulsed laser deposition (PLD) method have been investigated by cyclic voltammetry and charge/discharge measurements. A large reversible capacity of nanocomposite Fe₂O₃-Se thin film was found to be around 650 mAh g⁻¹. A new couple of reduction and oxidation peaks at 1.4 and 1.8 V were observed from cyclic voltammogram for the first time. Our data demonstrated that nanocomposite Fe₂O₃-Se exhibit larger capacity and better cycle performance than pure Fe₂O₃. The electrochemical reaction mechanisms of Fe₂O₃-Se with lithium were examined by X-ray photoelectron spectroscopy (XPS), high resolution transmission electron microscopy (HRTEM) and selected-area electron diffraction (SAED). The reversible conversions reaction of nanosized metal Fe with Li₂Se and Li₂O formed after initial discharge process into FeSe and Fe₂O₃ respectively were revealed.     

La1−xSrxFeO3−δ perovskites as redox materials for application in a membrane reactor for simultaneous production of pure hydrogen and synthesis gas

This work reports on the preparation and characterization of perovskitic materials with the general formula La_1−xSr_xFeO₃ (x = 0, 0.3, 0.7, 1) for application in a dense mixed conducting membrane reactor process for simultaneous production of synthesis gas and pure hydrogen. Thermogravimetric experiments indicated that the materials are able to loose and uptake reversibly oxygen from their lattice up to 0.2 oxygen atoms per “mole” for SrFeO₃ with x = 1 at 1000 °C. The capability of the prepared powders to convert CH₄ during the reduction step, in order to produce synthesis gas, as well as their capability to dissociate water during the oxidation step, in order to produce hydrogen were evaluated by pulse reaction experiments in a fixed bed pulse reactor. The high sintering temperatures (1100-1300 °C) required for the densification of the membrane materials result in decreased methane conversion and H₂ yields during the reduction step compared to the corresponding values obtained with the perovskite powders calcined at 1000 °C. Addition of small quantities of NiO, by simple mechanical mixing, to the perovskites after their sintering at high temperatures, increases substantially both their methane decomposition reactivity, their selectivity towards CO and H₂ and their water splitting activity. Maximum H₂ yield during the reduction step is achieved with the La_0.7Sr_0.3FeO₃ sample mixed with 5% NiO and is 80% of the theoretically expected H₂, based on complete methane decomposition. In the oxidation - water splitting step, 912 μmol H₂ per gr solid are produced with the La_0.3Sr_0.7FeO₃ sample mixed with 5% NiO. The experimental results of this work can be equally well applied for the “chemical-looping reforming” process since they concern using the lattice oxygen of the perovskite oxides for methane partial oxidation to syngas, in the absence of molecular oxygen, and subsequent oxidation of the solid.     

Electrochemical performance of the carbon coated Li3V2(PO4)3 cathode material synthesized by a sol-gel method

A carbon coated Li₃V₂(PO₄)₃ cathode material for lithium ion batteries was synthesized by a sol-gel method using V₂O₅, H₂O₂, NH₄H₂PO₄, LiOH and citric acid as starting materials, and its physicochemical properties were investigated using X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) spectroscopy, scanning electron microscopy (SEM), energy dispersive analysis of X-ray (EDAX), transmission electron microscope (TEM), and electrochemical methods. The sample prepared displays a monoclinic structure with a space group of P2₁/n, and its surface is covered with a rough and porous carbon layer. In the voltage range of 3.0-4.3 V, the Li₃V₂(PO₄)₃ electrode displays a large reversible capacity, good rate capability and excellent cyclic stability at both 25 and 55 °C. The largest reversible capacity of 130 mAh g⁻¹ was obtained at 0.1C and 55 °C, nearly equivalent to the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹). It was found that the increase in total carbon content can improve the discharge performance of the Li₃V₂(PO₄)₃ electrode. In the voltage range of 3.0-4.8 V, the extraction and reinsertion of the third lithium ion in the carbon coated Li₃V₂(PO₄)₃ host are almost reversible, exhibiting a reversible capacity of 177 mAh g⁻¹ and good cyclic performance. The reasons for the excellent electrochemical performance of the carbon coated Li₃V₂(PO₄)₃ cathode material were also discussed.