Preparation and electrochemical properties of a LiFePO4/C composite cathode material by a polymer-pyrolysis–reduction method

A LiFePO₄/C composite was successfully prepared by a polymer-pyrolysis–reduction method, using FePO₄·2H₂O and lithium polyacrylate (PAALi) as raw materials. The structure of the LiFePO₄/C composites was investigated by X-ray diffraction (XRD). The micromorphology of the precursor and LiFePO₄/C powders was observed using scanning electron microscopy (SEM), and the in situ coating of carbon on the particles was observed by transmission electron microscopy (TEM). Furthermore, the electrochemical properties were evaluated by cyclic voltammograms (CVs), electrochemical impedance spectra (EIS) and constant current charge/discharge cycling tests. The results showed that the sample synthesized at 700 °C had the best electrochemical performance, exhibiting initial discharge capacities of 157, 139 and 109 mAh g⁻¹ at rates of 0.1, 1 and 5 C, respectively. Moreover, the sample presented excellent capacity retention as there was no significant capacity fade after 50 cycles.     

Properties of Li-graphite and LiFePO4 electrodes in LiPF6–sulfolane electrolyte

Sulfolane (also referred to as tetramethylene sulfone, TMS) containing LiPF₆ and vinylene carbonate (VC) was tested as a non-flammable electrolyte for a graphite |LiFePO₄ lithium-ion battery. Charging/discharging capacity of the LiFePO₄ electrode was ca. 150 mAh g⁻¹ (VC content 5 wt%). The capacity of the graphite electrode after 10 cycles establishes at the level of ca. 350 mAh g⁻¹ (C/10 rate). In the case of the full graphite |1 M LiPF₆ + TMS + VC 10 wt% |LiFePO₄ cell, both charging and discharging capacity (referred to cathode mass) stabilized at a value of ca. 120 mAh g⁻¹. Exchange current density for Li⁺ reduction on metallic lithium, estimated from electrochemical impedance spectroscopy (EIS) experiments, was j_o(Li/Li⁺) = 8.15 × 10⁻⁴ A cm⁻². Moreover, EIS suggests formation of the solid electrolyte interface (SEI) on lithium, lithiated graphite and LiFePO₄ electrodes, protecting them from further corrosion in contact with the liquid electrolyte. Scanning electron microscopy (SEM) images of pristine electrodes and those taken after electrochemical cycling showed changes which may be interpreted as a result of SEI formation. No graphite exfoliation was observed. The main decomposition peak of the LiPF₆ + TMS + VC electrolyte (TG/DTA experiment) was present at ca. 275 °C. The LiFePO₄(solid) + 1 M LiPF₆ + TMS + 10 wt% VC system shows a flash point of ca. 150 °C. This was much higher in comparison to that characteristic of a classical LiFePO₄ (solid) + 1 M LiPF₆ + 50 wt% EC + 50 wt% DMC system (T_f ≈ 37 °C).     

High power performance of nano-LiFePO4/C cathode material synthesized via lauric acid-assisted solid-state reaction

A nano-LiFePO₄/C composite has been directly synthesized from micrometer-sized Li₂CO₃, NH₄H₂PO₄, and FeC₂O₄·2H₂O by the lauric acid-assisted solid-state reaction method. The SEM and TEM observations demonstrate that the synthesized nano-LiFePO₄/C composite has well-dispersed particles with a size of about 100–200 nm and an in situ carbon layer with thickness of about 2 nm. The prepared nano-LiFePO₄/C composite has superior rate capability, delivering a discharge capacity of 141.2 mAh g⁻¹ at 5 °C, 130.9 mAh g⁻¹ at 10 C, 121.7 mAh g⁻¹ at 20 °C, and 112.4 mAh g⁻¹ at 30 °C. At −20 °C, this cathode material still exhibits good rate capability with a discharge capacity of 91.9 mAh g⁻¹ at 1 °C. The nano-LiFePO₄/C composite also shows excellent cycling ability with good capacity retention, up to 100 cycles at a high current density of 30 °C. Furthermore, the effect of lauric acid in the preparation of nano-LiFePO₄/C composite was investigated by comparing it with that of citric acid. The SEM images reveal that the morphology of the LiFePO₄/C composite transformed from the porous structure to fine particles as the molar ratio of lauric acid/citric acid increased.     

Synthesis and characterization of high-density LiFePO4/C composites as cathode materials for lithium-ion batteries

To achieve a high-energy-density lithium electrode, high-density LiFePO₄/C composite cathode material for a lithium-ion battery was synthesized using self-produced high-density FePO₄ as a precursor, glucose as a C source, and Li₂CO₃ as a Li source, in a pipe furnace under an atmosphere of 5% H₂-95% N₂. The structure of the synthesized material was analyzed and characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). The electrochemical properties of the synthesized LiFePO₄/carbon composite were investigated by cyclic voltammetry (CV) and the charge/discharge process. The tap-density of the synthesized LiFePO₄/carbon composite powder with a carbon content of 7% reached 1.80 g m⁻³. The charge/discharge tests show that the cathode material has initial charge/discharge capacities of 190.5 and 167.0 mAh g⁻¹, respectively, with a volume capacity of 300.6 mAh cm⁻³, at a 0.1C rate. At a rate of 5C, the LiFePO₄/carbon composite shows a high discharge capacity of 98.3 mAh g⁻¹ and a volume capacity of 176.94 mAh cm⁻³.     

1-Alkyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide ionic liquids as highly safe electrolyte for Li/LiFePO4 battery

Several 1-alkyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide ionic liquids (alkyl-DMimTFSI) were prepared by changing carbon chain lengths and configuration of the alkyl group, and their electrochemical properties and compatibility with Li/LiFePO₄ battery electrodes were investigated in detail. Experiments indicated the type of ionic liquid has a wide electrochemical window (−0.16 to 5.2 V vs. Li⁺/Li) and are theoretically feasible as an electrolyte for batteries with metallic lithium as anode. Addition of vinylene carbonate (VC) improves the compatibility of alkyl-DMimTFSI-based electrolytes towards lithium anode and LiFePO₄ cathode, and enhanced the formation of solid electrolyte interface to protect lithium anodes from corrosion. The electrochemical properties of the ionic liquids obviously depend on carbon chain length and configuration of the alkyl, including ionic conductivity, viscosity, and charge/discharge capacity etc. Among five alkyl-DMimTFSI-LiTFSI-VC electrolytes, Li/LiFePO₄ battery with the electrolyte-based on amyl-DMimTFSI shows best charge/discharge capacity and reversibility due to relatively high conductivity and low viscosity, its initial discharge capacity is about 152.6 mAh g⁻¹, which the value is near to theoretical specific capacity (170 mAh g⁻¹). Although the battery with electrolyte-based isooctyl-DMimTFSI has lowest initial discharge capacity (8.1 mAh g⁻¹) due to relatively poor conductivity and high viscosity, the value will be dramatically added to 129.6 mAh g⁻¹ when 10% propylene carbonate was introduced into the ternary electrolyte as diluent. These results clearly indicates this type of ionic liquids have fine application prospect for lithium batteries as highly safety electrolytes in the future.     

Effect of CeO2-coating on the electrochemical performances of LiFePO4/C cathode material

The effect of CeO₂ coating on LiFePO₄/C cathode material has been investigated. The crystalline structure and morphology of the synthesized powders have been characterized by XRD, SEM, TEM and their electrochemical performances both at room temperature and low temperature are evaluated by CV, EIS and galvanostatic charge/discharge tests. It is found that, nano-CeO₂ particles distribute on the surface of LiFePO₄ without destroying the crystal structure of the bulk material. The CeO₂-coated LiFePO₄/C cathode material shows improved lithium insertion/extraction capacity and electrode kinetics, especially at high rates and low temperature. At −20 °C, the CeO₂-coated material delivers discharge capacity of 99.7 mAh/g at 0.1C rate and the capacity retention of 98.6% is obtained after 30 cycles at various charge/discharge rates. The results indicate that the surface treatment should be an effective way to improve the comprehensive properties of the cathode materials for lithium ion batteries.     

Synthesis of spindle-shaped nanoporous C–LiFePO4 composite and its application as a cathodes material in lithium ion batteries

In this work, LiFePO₄/C composites were prepared in hydrothermal system by using iron gluconate as iron source, and two feeding sequences during the preparation were comparatively studied. The morphology, crystal structure and charge–discharge performance of the prepared samples were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and galvanostatic charge–discharge testing. The results showed that the feeding sequences and iron gluconate seriously affected the microstructures and electrochemical properties of the resulting LiFePO₄ cathodes in lithium ion batteries. The spindle-shaped LiFePO₄ with hierarchical microporous structure self-assembled by nanoparticles has been successfully synthesized by synthesis route B. In addition, the cell performance of the synthesized LiFePO₄ by synthesis route B was better than that of LiFePO₄ by synthesis route A. Specially at high rates, the superior rate performance of the spindle-shaped LiFePO₄/C microstructure (LFP/C-B) was revealed. And special reversible capacities of ∼118 and ∼95 mAh g⁻¹ were obtained at rates of 2 C and 5 C, comparing to ∼96 and ∼68 mAh g⁻¹ for LFP/C-A.     

Enhanced rate performance of nano–micro structured LiFePO4/C by improved process for high-power Li-ion batteries

A spherical carbon-coated nano–micro structured LiFePO₄ composite is synthesized for use as a cathode material in high-power lithium-ion batteries. The composites are synthesized through carbothermal reduction with two sessions of ball milling (before and after pre-sintering of precursor) followed by spray-drying with the dispersant of polyethylene glycol added. The structure, particle size, and surface morphology of the cathode active material and the properties of the coated carbon are investigated by X-ray diffraction, Raman spectroscopy, scanning electron microscopy, and high-resolution transmission electron microscopy. Results indicate that the LiFePO₄/C composite has a spherical micro-porous morphology composed of a large number of carbon-coated nano-spheres linked together with an ordered olivine structure. The carbon on the surface of LiFePO₄ effectively reduces inter-particle agglomeration of the LiFePO₄ particles. A galvanostatic charge–discharge test indicates that the LiFePO₄/C composites exhibit initial discharge capacities of 155 mAh g⁻¹ and 88 mAh g⁻¹ at 0.2 C and 20 C rates with the end of discharge voltage of 2.5 V, respectively. This behavior is ascribed to the unique spherical structure, which shortens lithium ions diffusion length and improves the electric contact between LiFePO₄ particles.     

Enhanced performance of LiFePO4 through hydrothermal synthesis coupled with carbon coating and cupric ion doping

A hydrothermal reaction has been adopted to synthesize pure LiFePO₄ first, which was then modified with carbon coating and cupric ion (Cu²⁺) doping simultaneously through a post-heat treatment. X-ray diffraction patterns, transmission electron microscopy and scanning electron microscopy images along with energy dispersive spectroscopy mappings have verified the homogeneous existence of coated carbon and doped Cu²⁺ in LiFePO₄ particles with phospho-olivine structure and an average size of 400 nm. The electrochemical performances of the material have been studied by cyclic voltammetry, electrochemical impedance spectroscopy and galvanostatic charge–discharge measurements. The carbon-coated and Cu²⁺-doped LiFePO₄ sample (LFCu5/C) exhibited an enhanced electronic conductivity of 2.05 × 10⁻³ S cm⁻¹, a specific discharge capacity of 158 mAh g⁻¹ at 50 mA g⁻¹, a capacity retention of 96.4% after 50 cycles, a decreased charge transfer resistance of 79.4 Ω and superior electrode reaction reversibility. The present synthesis route is promising in making the hydrothermal method more practical for preparation of the LiFePO₄ material and enhancement of electrochemical properties.     

High capacity ZnFe2O4 anode material for lithium ion batteries

A nanostructured ternary transition metal oxide, ZnFe₂O₄, is synthesized via the simple polymer pyrolysis method. The characteristics of the material are examined by thermogravimetry, Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The electrochemical test results show that this method of ZnFe₂O₄ synthesis produces high specific capacities and good cycling performance, with an initial specific capacity as high as 1419.6 mAh g⁻¹ at first discharge that is maintained at over 800 mAh g⁻¹ even after 50 charge–discharge cycles. The electrode also presents a good rate capability, with a high rate of 4C (1C = 928 mA g⁻¹), a reversible specific capacity that can be as high as 400 mAh g⁻¹. ZnFe₂O₄ is a potential alternative to high-performance nanostructured anode material in lithium ion batteries.     

Electrochemical properties of bare and Ta-substituted Nb2O5 nanostructures

In this work, bare and Ta-substituted Nb₂O₅ nanofibers are prepared by electrospinning followed by sintering at temperatures in the 800–1100 °C range for 1 h in air. Obtained bare and Ta-substituted Nb₂O₅ polymorphs are characterized by X-ray diffraction, scanning electron microscopy, density measurement, and Brunauer, Emmett and Teller surface area. Electrochemical properties are evaluated by cyclic voltammetry and galvanostatic techniques. Cycling performance of Nb₂O₅ structures prepared at temperature 800 °C, 900 °C, and 1100 °C shows following discharge capacity at the end of 10th cycle: 123, 140, and 164 (±3) mAh g⁻¹, respectively, in the voltage range 1.2–3.0 V and at current rate of 150 mA g⁻¹ (1.5 C rate). Heat treated composite electrode based on M-Nb₂O₅ (1100 °C) in argon atmosphere at 220 °C, shows an improved discharge capacity of 192 (±3) mAh g⁻¹ at the end of 10th cycle. The discharge capacity of Ta-substituted Nb₂O₅ prepared at 900 °C and 1100 °C showed a reversible capacity of 150, 202 (±3) mAh g⁻¹, respectively, in the voltage range 1.2–3.0 V and at current rate of 150 mA g⁻¹. Anodic electrochemical properties of M-Nb₂O₅ deliver a reversible capacity of 382 (±5) mAh g⁻¹ at the end of 25th cycle and Ta-substituted Nb₂O₅ prepared at 900 °C, 1000 °C and 1100 °C shows a reversible capacity of 205, 130 and 200 (±3) mAh g⁻¹ (at 25th cycle) in the range, 0.005–2.6 V, at current rate of 100 mA g⁻¹.     

One-step hydrothermal synthesis of 3D porous microspherical LiFePO4/graphene aerogel composite for lithium-ion batteries

Three-dimensional (3D) porous LiFePO₄/graphene aerogel (LFP/GA) composite was successfully prepared by an in-situ hydrothermal process. In this composite, the LiFePO₄ microspheres assembled by nanoparticles were embedded in a three-dimensional framework intertwined with the graphene sheets, which acts as a bridge for transfer of electron and diffusion of lithium ion. The large specific surface of the composite structure enables the increased infiltration area and utilization of the active material. The content of the graphene sheet is analyzed and is found important for the Li-storage characteristics of LiFePO₄. An aerogel composite with 10% of graphene displays the best electrochemical performance, with the specific discharge capacities of 168 mAh g⁻¹ and 155 mAh g⁻¹ at respectively 0.1C and 1C, and the capacity retains 96.3% for up to 800 cycles. This novel 3D porous aerogel composite is identified as a promising cathode material for the rechargeable Li battery, and the simple strategy may be applied to construct other high performing composite structure and materials.     

A novel synthesis of spherical LiFePO4/C composite using Fe1.5P and mixed lithium salts via oxygen permeation

A novel route was designed to synthesize LiFePO₄/C composites by using the Fe_1.5P byproduct, mixed lithium salts, and permeated oxygen from air via a rheological phase method. The reaction process was investigated with various techniques. When the calcining time was increased from 10 to 30 h, the gradual formation of olivine structure was observed. The growth kinetics of the crystals was analyzed. SEM and TEM results indicated the as-synthesized LiFePO₄ was constituted of small spheres covered with carbon particles. The discharge capacity of the LiFePO₄/C composite prepared at ??700 °C for ??25 h could reach 139.7 mAh g^?1 and still remained 130.2 mAh g^?1 after 15 cycles at 0.2 C rate, comparable to that of the reported LiFePO₄/C composite using conventional methods. Cyclic voltammogram confirmed the LiFePO₄/C composite had a high purity and good lithium ion insertion/desertion redox behavior.     

Effects of Na and Cl co-doping on electrochemical performance in LiFePO4/C

Na⁺ and Cl⁻ co-doped LiFePO₄/C composites were prepared via a simple solid state reaction. The structure, valence state and electrochemical performance were carefully investigated. Rietveld refinement on X-ray diffractions reveals that Na⁺ and Cl⁻ have successfully been introduced into the lattice of LiFePO₄. X-ray photoelectron spectroscopy proves that the co-doping of Na⁺ and Cl⁻ does not change the chemical state of Fe(II). Experimental results further show that the co-doping contributes to induce the lattice distortion, modify the particle morphology, and increase the electronic conductivity. Considerably enhanced capacity, coulombic efficiency and rate capability were obtained in the co-doped LiFePO₄. The specific capacities are 157 mAh g⁻¹ at 0.2 C, 115 mAh g⁻¹ at 10 C and 98 mAh g⁻¹ at 20 C for the (Na⁺, Cl⁻) co-doped LiFePO₄/C cathode material. The improvement can be ascribed to the enhanced electronic conductivity and electrode kinetics due to the micro-structural modification promoted by co-doping.     

Preparation and characterization of core–shell structure Fe3O4/C nanoparticles with unique stability and high electrochemical performance for lithium-ion battery anode material

Core–shell structure carbon coating Fe₃O₄ nanoparticles are prepared by a two-step method. The crystalline structure and the electrochemical performance of the prepared samples are investigated. The results indicate that a uniform and continuous carbon layer is formed on the surface of Fe₃O₄ nanoparticles. The core–shell structure Fe₃O₄/C nanoparticles show a high initial discharge capacity of 1546 mAh g⁻¹ and a specific stable discharge capacity of about 800 mAh g⁻¹ at 0.5 C with no noticeable capacity fading up to 100 cycles.     

Electrochemical performance of single crystalline spinel LiMn2O4 nanowires in an aqueous LiNO3 solution

Single crystalline cubic spinel LiMn₂O₄ nanowires were synthesized by hydrothermal method and the precursor calcinations. The phase structures and morphologies were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and high-resolution transmission electron microscopy (HRTEM). Galvanostatic charging/discharging cycles of as-prepared LiMn₂O₄ nanowires were performed in an aqueous LiNO₃ solution. The initial discharge capacity of LiMn₂O₄ nanowires was 110 mAh g⁻¹, and the discharge capacity was still above 100 mAh g⁻¹ after 56 cycles at 10C-rate, and then 72 mAh g⁻¹ was registered after 130 cycles. This is the first report of a successful use of single crystalline spinel LiMn₂O₄ nanowire as cathode material for the aqueous rechargeable lithium battery (ARLB).     

Electrochemical properties of carbon-mixed LiFePO4 cathode material synthesized by the ceramic granulation method

LiFePO₄/carbon composite cathode material was prepared using polyvinyl alcohol (PVA) as carbon source by pelleting and subsequent pyrolysis in N₂. The samples were characterized by XRD, SEM and TGA. Their electrochemical performance was investigated in terms of charge–discharge cycling behavior. It consists of a single LiFePO₄ phase and amorphous carbon. The special micro-morphology via the process is favorable for electrochemical properties. The discharge capacity of the LiFePO₄/C composite was 145 mAh/g, closer to the theoretical specific capacity of 170 mAh/g at 0.1 C low current density. At 3 C modest current density, the specific capacity was about 80 mAh/g, which can satisfy for transportation applications if having a more planar discharge flat.     

Enhanced rate performance of carbon-coated LiNi0.5Mn1.5O4 cathode material for lithium ion batteries

Conductive carbon has been coated on the surface of LiNi_0.5Mn_1.5O₄ cathode material by the carbonization of sucrose for the purpose of improving the rate performance. The effect of carbon coating on the physical and electrochemical properties is discussed through the characterizations of X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), cycling and rate tests. Results demonstrate that the carbon coating can greatly enhance the discharge capacity, rate capability and cycling stability of the LiNi_0.5Mn_1.5O₄ without degrading the spinel structure. The sample modified with 1 wt.% sucrose displays the best performance. A large capacity of 130 mAh g⁻¹ at 1 C discharge rate with a high retention of 92% after 100 cycles and a stable 114 mAh g⁻¹ at 5 C discharge rate can be delivered. The remarkably improved rate properties of the carbon-coated samples are due to the suppression of the solid electrolyte interfacial (SEI) layer development and faster kinetics of both the Li⁺ diffusion and the charge transfer reaction.     

Enhanced electrochemical properties of LiFePO4/C synthesized with two kinds of carbon sources,PEG-4000 (organic) and Super p (inorganic)

Olivine structured LiFePO₄/C cathode was synthesized via a freeze-drying route and followed by microwave heating with two kinds of carbon sources: PEG-4000 (organic) and Super p (inorganic). XRD patterns indicate that the as-prepared sample has an olivine structure and carbon modification does not affect the structure of the sample. Image of SEM shows a uniform and optimized particles size, which greatly improves the electrochemical properties. TEM result reveals the amorphous carbon around the surface of the particles. At a low rate of 0.1 C, the LiFePO₄/C sample presents a high discharge capacity of 157.8 mAh g⁻¹ which is near the theoretical capacity (170 mAh g⁻¹), and it still attains to 149.1 mAh g⁻¹ after 200 cycles. It also exhibits an excellent rate capacity with high discharge capacities of 143.2 mAh g⁻¹, 137.5 mAh g⁻¹, 123.7 mAh g⁻¹ and 101.6 mAh g⁻¹ at 0.5 C, 1.0 C, 2.0 C and 5.0 C, respectively. EIS results indicate that the charge transfer resistance of LiFePO₄ decreases greatly after carbon coating.     

Effect of carbon coating on low temperature electrochemical performance of LiFePO4/C by using polystyrene sphere as carbon source

Carbon perfectly coated LiFePO₄ cathode materials are synthesized by carbon-thermal reduction method using polystyrene (PS) spheres as carbon source. The PS spheres with diameters of 150–300 nm used for the pyrolysis reaction not only inhibit the particle growth but also lead to uniform distribution of carbon coating on the surface of LiFePO₄ particles. Rate capability and cycling stability of LiFePO₄/C with the carbon contents ranging from 1.4 wt% to 3.7 wt% are investigated at −20 °C. The LiFePO₄/C with 3.0 wt% C exhibits excellent electrochemical capability at low temperature, which delivers 147 mAh g⁻¹ at 0.1 C. After 100 cycles at a charge–discharge rate of 1 C, there is still 100% of initial capacity retained for the LiFePO₄/C electrode at −20 °C. According to the transmission electron microscope analysis and cyclic voltammetry measurement, this can be attributed to the good carbon coating morphology and optimal carbon coating thickness.