Influence of Phase Segregation on Recombination Dynamics in Organic Bulk‐Heterojunction Solar Cells

The recombination dynamics of charge carriers in organic bulk‐heterojunction (BHJ) solar cells made of the blend system poly(2,5‐bis(3‐dodecylthiophen‐2‐yl)thieno[2,3‐b]thiophene) (pBTCT‐C₁₂):[6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) with a donor–acceptor ratio of 1:1 and 1:4 are studied here. The techniques of charge‐carrier extraction by linearly increasing voltage (photo‐CELIV) and, as local probe, time‐resolved microwave conductivity are used. A difference of one order of magnitude is observed between the two blends in the initially extracted charge‐carrier concentration in the photo‐CELIV experiment, which can be assigned to an enhanced geminate recombination that arises through a fine interpenetrating network with isolated phase regions in the 1:1 pBTCT‐C₁₂:PC₆₁BM BHJ solar cells. In contrast, extensive phase segregation in 1:4 blend devices leads to an efficient polaron generation that results in an increased short‐circuit current density of the solar cells. For both studied ratios a bimolecular recombination of polarons is found using the complementary experiments. The charge‐carrier decay order of above two for temperatures below 300 K can be explained on the basis of a release of trapped charges. This mechanism leads to delayed bimolecular recombination processes. The experimental findings can be generalized to all polymer:fullerene blend systems allowing for phase segregation.     

Towards Efficient Integrated Perovskite/Organic Bulk Heterojunction Solar Cells: Interfacial Energetic Requirement to Reduce Charge Carrier Recombination Losses

Integrated perovskite/organic bulk heterojunction (BHJ) solar cells have the potential to enhance the efficiency of perovskite solar cells by a simple one‐step deposition of an organic BHJ blend photoactive layer on top of the perovskite absorber. It is found that inverted structure integrated solar cells show significantly increased short‐circuit current (J_sc) gained from the complementary absorption of the organic BHJ layer compared to the reference perovskite‐only devices. However, this increase in J_sc is not directly reflected as an increase in power conversion efficiency of the devices due to a loss of fill factor. Herein, the origin of this efficiency loss is investigated. It is found that a significant energetic barrier (≈250 meV) exists at the perovskite/organic BHJ interface. This interfacial barrier prevents efficient transport of photogenerated charge carriers (holes) from the BHJ layer to the perovskite layer, leading to charge accumulation at the perovskite/BHJ interface. Such accumulation is found to cause undesirable recombination of charge carriers, lowering surface photovoltage of the photoactive layers and device efficiency via fill factor loss. The results highlight a critical role of the interfacial energetics in such integrated cells and provide useful guidelines for photoactive materials (both perovskite and organic semiconductors) required for high‐performance devices.     

In‐Plane Alignment in Organic Solar Cells to Probe the Morphological Dependence of Charge Recombination

Bulk heterojunction (BHJ) organic solar cells are fabricated with the polymer semiconductor aligned in the plane of the film to probe charge recombination losses associated with aggregates characterized by varying degrees of local order. 100% uniaxial strain is applied on ductile poly(3‐hexylthiophene):phenyl‐C61‐butyric acid methyl ester (P3HT:PCBM) BHJ films and characterize the resulting morphology with ultraviolet‐visible absorption spectroscopy and grazing incidence X‐ray diffraction. It is found that the strained films result in strong alignment of the highly ordered polymer aggregates. Polymer aggregates with lower order and amorphous regions also align but with a much broader orientation distribution. The solar cells are then tested under linearly polarized light where the light is selectively absorbed by the appropriately oriented polymer, while maintaining a common local environment for the sweep out of photogenerated charge carriers. Results show that charge collection losses associated with a disordered BHJ film are circumvented, and the internal quantum efficiency is independent of P3HT local aggregate order near the heterojunction interface. Uniquely, this experimental approach allows for selective excitation of distinct morphological features of a conjugated polymer within a single BHJ film, providing insight into the morphological origin of recombination losses.     

Influence of Solvent Mixing on the Morphology and Performance of Solar Cells Based on Polyfluorene Copolymer/Fullerene Blends

The influence of the solvent on the morphology and performance of polymer solar cells is investigated in devices based on blends of the polyfluorene copolymer, poly(2,7‐(9,9‐dioctyl‐fluorene)‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole)), and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester. The blends are spin‐coated from chloroform or from chloroform mixed with small amounts of xylene, toluene, or chlorobenzene. The devices are characterized under monochromatic light and solar illumination AM1.5 (AM: air mass). An enhancement of the photocurrent density is observed in diodes made from chloroform mixed with chlorobenzene, and reduced photocurrent density is observed in diodes made from chloroform mixed with xylene or toluene, compared to diodes made from neat chloroform. The open‐circuit voltages are almost the same in all diodes. The surfaces of the active layers are imaged using atomic force microscopy. Height images indicate that a finer and more uniform distribution of domains corresponds to the diodes with enhanced photocurrent that are made from chloroform mixed with chlorobenzene, while a structure with larger domains is associated with the lower photocurrents in the diodes made from chloroform mixed with xylene or toluene. The influence of the morphology on the excited‐state dynamics and charge generation is investigated using time‐resolved spectroscopy. Fast formation of bound charge pairs followed by their conversion into free charge carriers is resolved, and excitation‐intensity‐dependent non‐geminate recombination of free charges is observed. A significant enhancement in free‐charge‐carrier generation is observed on introducing chlorobenzene into chloroform. Imaging photocurrent generation from the solar cells with a light‐pulse technique shows an inhomogeneous photocurrent distribution, which is related to the undulations in the thickness of the active layer. Thicker parts of the diodes yield higher photocurrent values.     

Identifying a Threshold Impurity Level for Organic Solar Cells: Enhanced First‐Order Recombination Via Well‐Defined PC84BM Traps in Organic Bulk Heterojunction Solar Cells

Small amounts of impurity, even one part in one thousand, in polymer bulk heterojunction solar cells can alter the electronic properties of the device, including reducing the open circuit voltage, the short circuit current and the fill factor. Steady state studies show a dramatic increase in the trap‐assisted recombination rate when [6,6]‐phenyl C₈₄ butyric acid methyl ester (PC₈₄BM) is introduced as a trap site in polymer bulk heterojunction solar cells made of a blend of the copolymer poly[N‐9″‐hepta‐decanyl‐2,7‐carbazole‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole) (PCDTBT) and the fullerene derivative [6,6]‐phenyl C₆₁ butyric acid methyl ester (PC₆₀BM). The trap density dependent recombination studied here can be described as a combination of bimolecular and Shockley–Read–Hall recombination; the latter is dramatically enhanced by the addition of the PC₈₄BM traps. This study reveals the importance of impurities in limiting the efficiency of organic solar cell devices and gives insight into the mechanism of the trap‐induced recombination loss.     

Charge Density Dependent Nongeminate Recombination in Organic Bulk Heterojunction Solar Cells

Apparent recombination orders exceeding the value of two expected for bimolecular recombination have been reported for organic solar cells in various publications. Two prominent explanations are bimolecular losses with a carrier concentration dependent prefactor due to a trapping limited mobility and protection of trapped charge carriers from recombination by a donor–acceptor phase separation until re‐emission from these deep states. In order to clarify which mechanism is dominant temperature‐ and illumination‐dependent charge extraction measurements are performed under open circuit and short circuit conditions at poly(3‐hexylthiophene‐2,5‐diyl):[6,6]‐phenyl‐C₆₁ butyric acid methyl ester (P3HT:PC₆₁BM) and PTB7:PC₇₁BM (poly[[4,8‐bis[(2‐ethylhexyl)oxy]benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl][3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]thieno[3,4‐b]thiophenediyl]]) solar cells in combination with current–voltage characteristics. It is shown that the charge carrier density n dependence of the mobility μ and the recombination prefactor are different for P3HT:PC₆₁BM at temperatures below 300 K and PTB7:PC₇₁BM at room temperature. Therefore, in addition to μ(n), a detrapping limited recombination in systems with at least partial donor–acceptor phase separation is required to explain the high recombination orders.     

Energy level alignment in PCDTBT:PC70BM solar cells: Solution processed NiOx for improved hole collection and efficiency

Solution-based NiO_x outperforms PEDOT:PSS in device performance and stability when used as a hole-collection layer in bulk-heterojunction (BHJ) solar cells formed with poly[N-9′-heptadecanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole) (PCDTBT) and PC₇₀BM. The origin of the enhancement is clarified by studying the interfacial energy level alignment between PCDTBT or the 1:4 blended heterojunctions and PEDOT:PSS or NiO_x using ultraviolet and inverse photoemission spectroscopies. The 1.6 eV electronic gap of PEDOT:PSS and energy level alignment with the BHJ result in poor hole selectivity of PEDOT:PSS and allows electron recombination at the PEDOT:PSS/BHJ interface. Conversely, the large band gap (3.7 eV) of NiO_x and interfacial dipole (?0.6 eV) with the organic active layer leads to a hole-selective interface. This interfacial dipole yields enhanced electron blocking properties by increasing the barrier to electron injection. The presence of such a strong dipole is predicted to further promote hole collection from the organic layer into the oxide, resulting in increased fill factor and short circuit current. An overall decrease in recombination is manifested in an increase in open circuit voltage and power conversion efficiency of the device on NiO_x versus PEDOT:PSS interlayers.     

Solution processable,precursor based zinc oxide buffer layers for 4.5% efficient organic tandem solar cells

In this work we present regular and inverted organic tandem solar cells from poly[N-9′-hepta-decanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole): [6,6]-phenyl C₇₀-butyric acid methyl ester (PCDTBT:PC₇₁BM) with power conversion efficiencies of up to 4.5%. The recombination zone comprises an electron conducting, precursor based zinc oxide buffer layer that was applied from solution under ambient conditions and at moderate processing temperatures. Optimized active layer thicknesses in both subcells were derived from optical Transfer Matrix simulations. The short circuit current density of the tandem cell exceeds half the short circuit current density of the single absorber cells indicating a real gain in quantum yield when utilizing the tandem architecture.     

Comparison of the Operation of Polymer/Fullerene,Polymer/Polymer,and Polymer/Nanocrystal Solar Cells: A Transient Photocurrent and Photovoltage Study

We utilize transient techniques to directly compare the operation of polymer/fullerene, polymer/nanocrystal, and polymer/polymer bulk heterojunction solar cells. For all devices, poly(3‐hexylthiophene) (P3HT) is used as the electron donating polymer, in combination with either the fullerene derivative phenyl‐C₆₁‐butyric acid methyl ester (PCBM) in polymer/fullerene cells, CdSe nanoparticles in polymer/nanocrystal cells, or the polyfluorene copolymer poly((9,9‐dioctylfluorene)‐2,7‐diyl‐alt‐[4,7‐bis(3‐hexylthien‐5‐yl)‐2,1,3‐benzothiadiazole]‐2,2‐diyl) (F8TBT) in polymer/polymer cells. Transient photocurrent and photovoltage measurements are used to probe the dynamics of charge‐separated carriers, with vastly different dynamic behavior observed for polymer/fullerene, polymer/polymer, and polymer/nanocrystal devices on the microsecond to millisecond timescale. Furthermore, by employing transient photocurrent analysis with different applied voltages we are also able to probe the dynamics behavior of these cells from short circuit to open circuit. P3HT/F8TBT and P3HT/CdSe devices are characterized by poor charge extraction of the long‐lived carriers attributed to charge trapping. P3HT/PCBM devices, in contrast, show relatively trap‐free operation with the variation in the photocurrent decay kinetics with applied bias at low intensity, consistent with the drift of free charges under a uniform electric field. Under solar conditions at the maximum power point, we see direct evidence of bimolecular recombination in the P3HT/PCBM device competing with charge extraction. Transient photovoltage measurements reveal that, at open circuit, photogenerated charges have similar lifetimes in all device types, and hence, the extraction of these long‐lived charges is a limiting process in polymer/nanocrystal and polymer/polymer devices.     

Relating the Morphology of Poly(p‐phenylene vinylene)/Methanofullerene Blends to Solar‐Cell Performance

The performance of bulk‐heterojunction solar cells based on a phase‐separated mixture of donor and acceptor materials is known to be critically dependent on the morphology of the active layer. Here we use a combination of techniques to resolve the morphology of spin cast films of poly(p‐phenylene vinylene)/methanofullerene blends in three dimensions on a nanometer scale and relate the results to the performance of the corresponding solar cells. Atomic force microscopy (AFM), transmission electron microscopy (TEM), and depth profiling using dynamic time‐of‐flight secondary ion mass spectrometry (TOF‐SIMS) clearly show that for the two materials used in this study, 1‐(3‐methoxycarbonyl)propyl‐1‐phenyl‐[6,6]‐methanofullerene (PCBM) and poly[2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐1,4‐phenylene vinylene] (MDMO‐PPV), phase separation is not observed up to 50 wt.‐% PCBM. Nanoscale phase separation throughout the film sets in for concentrations of more than 67 wt.‐% PCBM, to give domains of rather pure PCBM in a homogenous matrix of 50:50 wt.‐% MDMO‐PPV/PCBM. Electrical characterization, under illumination and in the dark, of the corresponding photovoltaic devices revealed a strong increase of power conversion efficiency when the phase‐separated network develops, with a sharp increase of the photocurrent and fill factor between 50 and 67 wt.‐% PCBM. As the phase separation sets in, enhanced electron transport and a reduction of bimolecular charge recombination provide the conditions for improved performance. The results are interpreted in terms of a model that proposes a hierarchical build up of two cooperative interpenetrating networks at different length scales.     

Homocoupling Defects in a Conjugated Polymer Limit Exciton Diffusion

Copolymers such as PCDTBT (poly(N‐9′‐heptadecanyl‐2,7‐carbazole‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole))) are commonly employed as donor material in bulk heterojunction solar cells. Recently, chemical defects such as homocouplings have been shown to form at the material synthesis stage, strongly reducing the short circuit current in organic photovoltaics. Here it is shown that both low molecular weight and homocoupling defects reduce the short circuit current of solar cells because of limited exciton diffusion. A model that unites and explains the influence of both chemical parameters with the distribution of conjugation lengths is proposed. The connection between limited exciton diffusion and short circuit current is revealed via kinetic Monte Carlo simulation of bulk heterojunctions. The findings are likely applicable for copolymers in general.     

Effects of Photo‐oxidation on the Performance of Poly[2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐1,4‐phenylene vinylene]:[6,6]‐Phenyl C61‐Butyric Acid Methyl Ester Solar Cells

A study of the photo‐oxidation of films of poly[2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐1,4‐phenylene vinylene] (MDMO‐PPV) blended with [6,6]‐phenyl C₆₁‐butyric acid methyl ester (PCBM), and solar cells based thereon, is presented. Solar‐cell performance is degraded primarily through loss in short‐circuit current density, J_SC. The effect of the same photodegradation treatment on the optical‐absorption, charge‐recombination, and charge‐transport properties of the active layer is studied. It is concluded that the loss in J_SC is primarily due to a reduction in charge‐carrier mobility, owing to the creation of more deep traps in the polymer during photo‐oxidation. Recombination is slowed down by the degradation and cannot therefore explain the loss in photocurrent. Optical absorption is reduced by photo‐bleaching, but the size of this effect alone is insufficient to explain the loss in device photocurrent.     

Origin of the Reduced Fill Factor and Photocurrent in MDMO‐PPV:PCNEPV All‐Polymer Solar Cells

The photogeneration mechanism in blends of poly[2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐1,4‐phenylene vinylene] (MDMO‐PPV) and poly[oxa‐1,4‐phenylene‐(1‐cyano‐1,2‐vinylene)‐(2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐1,4‐phenylene)‐1,2‐(2‐cyanovinylene)‐1,4‐phenylene] (PCNEPV) is investigated. The photocurrent in the MDMO‐PPV:PCNEPV blends is strongly dependent on the applied voltage as a result of a low dissociation efficiency of the bound electron–hole pairs. The dissociation efficiency is limited by low carrier mobilities, low dielectric constant, and the strong intermixing of the polymers, leading to a low fill factor and a reduced photocurrent at operating conditions. Additionally, electrons trapped in the PCNEPV phase recombine with the mobile holes in the MDMO‐PPV phase at the interface between the two polymers, thereby affecting the open‐circuit voltage and increasing the recombination losses. At an intensity of one sun, Langevin recombination of mobile carriers dominates over trap‐assisted recombination.     

Trap‐Assisted Recombination via Integer Charge Transfer States in Organic Bulk Heterojunction Photovoltaics

Organic photovoltaics are under intense development and significant focus has been placed on tuning the donor ionization potential and acceptor electron affinity to optimize open circuit voltage. Here, it is shown that for a series of regioregular‐poly(3‐hexylthiophene):fullerene bulk heterojunction (BHJ) organic photovoltaic devices with pinned electrodes, integer charge transfer states present in the dark and created as a consequence of Fermi level equilibrium at BHJ have a profound effect on open circuit voltage. The integer charge transfer state formation causes vacuum level misalignment that yields a roughly constant effective donor ionization potential to acceptor electron affinity energy difference at the donor–acceptor interface, even though there is a large variation in electron affinity for the fullerene series. The large variation in open circuit voltage for the corresponding device series instead is found to be a consequence of trap‐assisted recombination via integer charge transfer states. Based on the results, novel design rules for optimizing open circuit voltage and performance of organic bulk heterojunction solar cells are proposed.     

Improving the Photovoltage of Dithienopyrrole Dye‐Sensitized Solar Cells via Attaching the Bulky Bis(octyloxy)biphenyl Moiety to the Conjugated π‐Linker

The judicious design of 3D giant organic dye molecules to enable the formation of a porous photoactive layer on the surface of titania is one of the viable tactics to abate the adverse interfacial charge recombination in dye‐sensitized solar cells (DSCs) employing outer‐sphere redox couples. Here 2′,6′‐bis(octyloxy)‐biphenyl substituted dithieno[3,2‐b:2′,3′‐d]pyrrole segment is constructed and employed as the π‐linker of a high molar absorption coefficient organic push‐pull dye. With respect to its congener possessing the hexyl substituted dithieno[3,2‐b:2′,3′‐d]pyrrole linker, the new dye can self‐assemble on the surface of titania to afford a porous organic coating, which effectively slow down the kinetics of charge recombination of titania electrons with both outer‐sphere tris(1,10‐phenanthroline)cobalt(III) ions and photooxidized dye molecules, improving the cell photovoltage. In addition, the diminishments of charge recombination via modulating the microstructure of interfacial functional zone can also overcompensate the disadvantageous impact of reduced light‐harvesting and evoke an enhanced photocurrent output, bringing forth an efficiency improvement from 7.5% to 9.3% at the 100 mW cm^?2, simulated AM1.5 conditions.     

Bimolecular Crystals of Fullerenes in Conjugated Polymers and the Implications of Molecular Mixing for Solar Cells

The performance of polymer:fullerene bulk heterojunction solar cells is heavily influenced by the interpenetrating nanostructure formed by the two semiconductors because the size of the phases, the nature of the interface, and molecular packing affect exciton dissociation, recombination, and charge transport. Here, X‐ray diffraction is used to demonstrate the formation of stable, well‐ordered bimolecular crystals of fullerene intercalated between the side‐chains of the semiconducting polymer poly(2,5‐bis(3‐tetradecylthiophen‐2‐yl)thieno[3,2‐b]thiophene. It is shown that fullerene intercalation is general and is likely to occur in blends with both amorphous and semicrystalline polymers when there is enough free volume between the side‐chains to accommodate the fullerene molecule. These findings offer explanations for why luminescence is completely quenched in crystals much larger than exciton diffusion lengths, how the hole mobility of poly(2‐methoxy‐5‐(3′,7′‐dimethyloxy)‐p‐phylene vinylene) increases by over 2 orders of magnitude when blended with fullerene derivatives, and why large‐scale phase separation occurs in some polymer:fullerene blend ratios while thermodynamically stable mixing on the molecular scale occurs for others. Furthermore, it is shown that intercalation of fullerenes between side chains mostly determines the optimum polymer:fullerene blending ratios. These discoveries suggest a method of intentionally designing bimolecular crystals and tuning their properties to create novel materials for photovoltaic and other applications.     

8.91% Power Conversion Efficiency for Polymer Tandem Solar Cells

A power conversion efficiency of up to 8.91% is obtained for a solution‐processed polymer tandem solar cells based on a large‐bandgap polymer, poly(4,4‐dioctyldithieno(3,2‐b:2′,3′‐d)silole)‐2,6‐diyl‐alt‐(2,1,3‐benzothiadiazole)‐4,7‐diyl) with a polymeric interconnecting layer to electrically connect the front and rear subcells, demonstrating that proper device and interface engineering are can improve the performance of polymer tandem solar cells.     

Origin of Reduced Bimolecular Recombination in Blends of Conjugated Polymers and Fullerenes

Bimolecular charge carrier recombination in blends of a conjugated copolymer based on a thiophene and quinoxaline (TQ1) with a fullerene derivative ((6,6)‐phenyl‐C₇₁‐butyric acidmethyl ester, PC₇₁BM) is studied by two complementary techniques. TRMC (time‐resolved microwave conductance) monitors the conductance of photogenerated mobile charge carriers locally on a timescale of nanoseconds, while using photo‐CELIV (charge extraction by linearly increasing voltage) charge carrier dynamics are monitored on a macroscopic scale and over tens of microseconds. Despite these significant differences in the length and time scales, both techniques show a reduced Langevin recombination with a prefactor ζ close to 0.05. For TQ1:PC₇₁BM blends, the ζ value is independent of temperature. On comparing TRMC data with electroluminescence measurements it is concluded that the encounter complex and the charge transfer state have very similar energetic properties. The ζ value for annealed poly(3‐hexylthiophene) (P3HT):(6,6)‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) is approximately 10^?4, while for blend systems containing an amorphous polymer ζ values are close to 1. These large differences can be related to the extent of charge delocalization of opposite charges in an encounter complex. Insight is provided into factors governing the bimolecular recombination process, which forms a major loss mechanism limiting the efficiency of polymer solar cells.     

Dopant‐Free Spiro‐Triphenylamine/Fluorene as Hole‐Transporting Material for Perovskite Solar Cells with Enhanced Efficiency and Stability

Chemical doping is often used to enhance electric conductivity of the conjugated molecule as hole‐transporting material (HTM) for the application in optoelectronics. However, chemical dopants can promote ion migration at the electrical field, which deteriorates the device efficiency as well as increases the fabrication cost. Here, two star HTMs, namely 2,2′,7,7′‐tetrakis(N,N‐di‐p‐methoxyphenyl‐amine) 9,9′‐spirobifluorene (Spiro‐OMeTAD) and poly(triarylamine) are subjeted to chemical combination to yield dopant‐free N2,N2,N2′,N2′,N7,N7,N7′,N7′‐octakis(4‐methoxyphenyl)‐10‐phenyl‐10H‐spiro[acridine‐9,9′‐fluorene]‐2,2′,7,7′‐tetraamine (SAF‐OMe). The power conversion efficiencies (PCEs) of 12.39% achieved by solar cells based on pristine, dopant‐free SAF‐OMe are among the highest reported for perovskite solar cells and are even comparable to devices based on chemically doped Spiro‐OMeTAD (14.84%). Moreover, using a HTM comprised of SAF‐OMe with an additional dopant results in a record PCE of 16.73%. Compared to Spiro‐OMeTAD‐based devices, SAF‐OMe significantly improves stability.     

Enhancing Photovoltaic Performance Using an All‐Conjugated Random Copolymer to Tailor Bulk and Interfacial Morphology of the P3HT:ICBA Active Layer

Bulk heterojunction (BHJ) solar cells are fabricated using active material blends of poly(3‐hexylthiophene) (P3HT) donor, indene‐C₆₀ bisadduct (ICBA) acceptor, and an all‐conjugated random copolymer (RCP) additive. By optimizing RCP loading, power conversion efficiencies (PCEs) up to 20% higher than those of a binary P3HT:ICBA mixture are achieved. The improved device characteristics are rationalized in terms of the differences between the photoactive thin film morphologies. Energy‐filtered transmission electron micro­scopy reveals that incorporation of the RCP improves the degree of structural order of the BHJ fibrillar network and increases the extent of microphase separation between P3HT and ICBA. Additionally, a combination of atomic force microscopy and X‐ray photoelectron spectroscopy analysis indicates segregation of the RCP at the free interface, leading to a shift in the surface potentials measured by Kelvin probe force microscopy. These changes, both in the bulk morphology and in the interfacial composition/energetics, are correlated to improved carrier collection efficiency due to a reduction of non‐geminate recombination, which is measured by charge extraction of photo­generated carriers by linearly increasing voltage.