Transimpedance amplifier with a compression stage for wide dynamic range optical applications

A high dynamic input transimpedance amplifier was implemented in 130 nm CMOS technology. The proposed TIA is an inverter with a diode connected NMOS and a gate controlled PMOS loads which is cascode connected with the inverter. The square law compression NMOS increases the input photocurrent up to 10 mA. The TIA has an integrated input referred noise current of 135 nA, 227 MHz bandwidth. The TIA shows a transimpedance gain of 59 dBΩ and a 97 dB dynamic range. The TIA consumes 2.3 mA from 1.5 V voltage supply.     

An inductorless wideband common-gate LNA with dual capacitor cross-coupled feedback and negative impedance techniques

A wideband common-gate (CG) low-noise amplifier (LNA) with dual capacitor cross-coupled (CCC) feedback and negative impedance techniques is presented for multimode multiband wireless communication applications. Double CCC technique boosts the input transconductance of the LNA, and low power consumption is obtained by using current-reuse technique. Negative impedance technique is employed to alleviate the correlation between the transconductance of the matching transistors and input impedance. Meanwhile, it also allows us to achieve a lower noise figure (NF). Moreover, current bleeding technique is adopted to allow the choice of a larger load resistor without sacrificing the voltage headroom. The proposed architecture achieves low noise, low power and high gain simultaneously without the use of bulky inductors. Simulation results of a 0.18-μm CMOS implementation show that the proposed LNA provides a maximum voltage gain of 25.02 dB and a minimum NF of 2.37 dB from 0.1 to 2.25 GHz. The input-referred third-order intercept point (IIP3) and input 1-dB compression point (IP_1dB) are better than –7.8 dBm and –19.2 dBm, respectively, across the operating bandwidth. The circuit dissipates 3.24 mW from 1.8 V DC supply with an active area of 0.03 mm².     

A novel low voltage very low power CMOS class AB current output stage with ultra high output current drive capability

In this paper a novel low voltage (LV) very low power (VLP) class AB current output stage (COS) with extremely high linearity and high output impedance is presented. A novel current splitting method is used to minimize the transistors gate–source voltages providing LV operation and ultra high current drive capability. High linearity and very high output impedance are achieved employing a novel resistor based current mirror avoiding conventional cascode structures to be used. The operation of the proposed COS has been verified through HSPICE simulations based on TSMC 0.18 μm CMOS technology parameters. Under supply voltage of ±0.7 V and bias current of 5 μA, it can deliver output currents as high as 14 mA with THD better than ?53 dB and extremely high output impedance of 320 MΩ while consuming only 29 μW. This makes the proposed COS to have ultra large current drive ratio (I_outmax/I_bias or the ratio of peak output current to the bias current of output branch transistors) of 2800. By increasing supply voltage to ±0.9 V, it can deliver extremely large output current of ±24 mA corresponding to 3200 current drive ratio while consuming only 42.9 μW and exhibiting high output impedance of 350 MΩ. Interestingly, the proposed COS is the first yet reported one with such extremely high output current and a THD even less than ?45 dB. Such ultra high current drive capability, high linearity and high output impedance make the proposed COS an outstanding choice for LV, VLP and high drive current mode circuits. The superiority of the proposed COS gets more significance by showing in this work that conventional COS can deliver only ±3.29 mA in equal condition. The proposed COS also exhibits high positive and negative power supply rejection ratio (PSRR+/PSRR?) of 125 dB and 130 dB, respectively. That makes it very suitable for LV, VLP mixed mode applications. The Monte Carlo simulation results are provided, which prove the outstanding robust performance of the proposed block versus process tolerances. Favorably the proposed COS resolves the major limitation of current output stages that so far has prevented designing high drive current mode circuits under low supply voltages. In brief, the deliberate combination of so many effective novel methods presents a wonderful phenomenal COS block to the world of science and engineering.     

A broadband Low Noise Amplifier with built-in linearizer in 0.13-µm CMOS process

A linearized ultra-wideband (UWB) CMOS Low Noise Amplifier (LNA) is presented in this paper. The linearity performance is enhanced by exploiting PMOS–NMOS common-gate (CG) inverter as a built-in linearizer which leads to cancel out both the second- and third-order distortions. Two inductors are placed at the drain terminals of CG transistors in the built-in linearizer to adjust the phase and magnitude of the third-order distortion. A second-order band-pass Chebyshev filter is utilized in the input port of common-source (CS) configuration to provide broadband input matching at 3.1–10.6 GHz frequency range to a 50-Ω antenna. Series and shunt peaking techniques are employed to extend the bandwidth (BW) and to flatten the gain response. Simulated in 0.13 µm CMOS technology, the CMOS LNA exhibits state of the art performance consuming 17.92 mW of dc power. The CMOS LNA features a maximum gain of 10.24 dB, 0.9–4.1 dB noise figure (NF), and a third-order input intercept point (IIP3) of 6.8 dBm at 6.3 GHz.     

A novel low power UWB cascode SiGe BiCMOS LNA with current reuse and zero-pole cancellation

A low power cascode SiGe BiCMOS low noise amplifier (LNA) with current reuse and zero-pole cancellation is presented for ultra-wideband (UWB) application. The LNA is composed of cascode input stage and common emitter (CE) output stage with dual loop feedbacks. The novel cascode-CE current reuse topology replaces the traditional two stages topology so as to obtain low power consumption. The emitter degenerative inductor in input stage is adopted to achieve good input impedance matching and noise performance. The two poles are introduced by the emitter inductor, which will degrade the gain performance, are cancelled by the dual loop feedbacks of the resistance-inductor (RL) shunt–shunt feedback and resistance-capacitor (RC) series–series feedback in the output stage. Meanwhile, output impedance matching is also achieved. Based on TSMC 0.35 μm SiGe BiCMOS process, the topology and chip layout of the proposed LNA are designed and post-simulated. The LNA achieves the noise figure of 2.3–4.1 dB, gain of 18.9–20.2 dB, gain flatness of ±0.65 dB, input third order intercept point (IIP₃) of ?7 dBm at 6 GHz, exhibits less than 16 ps of group delay variation, good input and output impedances matching, and unconditionally stable over the whole band. The power consumption is only 18 mW.     

A high performance differential input CMOS current buffer

In this paper, a high accuracy CMOS differential input current buffer (CB) is proposed which employs super source followers (SSF) as input stage and regulated cascode (RGC) current mirrors as output stage. High accuracy requires very high output resistance and low input resistance. Small signal analysis is performed and it is shown that the proposed CB circuit has very low input impedances at ports n and p due to SSF transistors and also very high output impedance at output port due to RGC current mirrors. The simulation results show 9.72 Ω input resistances at ports n and p, 454 MΩ output resistance at output port with only 625 μW power consumption under ±0.9 V power supplies. The simulations are performed with HSpice using TSMC 0.18 μm process parameters and it is shown that the simulation results are in very good agreement with the theoretical ones.     

A UWB CMOS low-noise amplifier with noise reduction and linearity improvement techniques

In this paper, a highly linear CMOS low noise amplifier (LNA) for ultra-wideband applications is presented. The proposed LNA improves both input second- and third-order intercept points (IIP2 and IIP3) by canceling the common-mode part of all intermodulation components from the output current. The proposed LNA structure creates equal common-mode currents with the opposite sign by cascading two differential pairs with a cross-connected output. These currents eliminate each other at the output and improve the linearity. Also, the proposed LNA improves the noise performance by canceling the thermal noise of the input and auxiliary transistors at the output. Detailed analysis is provided to show the effectiveness of the proposed LNA structure. Post-layout circuit level simulation results using a 90 nm RF CMOS process with Spectre-RF reveal 9.5 dB power gain, -3 dB bandwidth (BW_−3dB) of 8 GHz from 2.4 GHz to 10.4 GHz, and mean IIP3 and IIP2 of +13.1 dBm and +42.8 dBm, respectively. The simulated S₁₁ is less than −11 dB in whole frequency range while the LNA consumes 14.8 mW from a single 1.2 V power supply.     

High rectifier output voltages with printed organic charge pump circuit

It is known that in many wireless organic electronic applications the required supply voltage is higher than the accessible signal amplitude. Therefore, voltage multiplier circuits are needed in many cases. We report a gravure printed organic charge pump circuit operating at 13.56 MHz suitable for rectified voltage amplification in printed electronic devices. The circuit, consisting of four diodes and four capacitors, has been monolithically printed using only high volume production compatible manufacturing methods. With 10 V AC input the output of the circuit at 13.56 MHz is 8.4 V and 11.8 V using 1 MΩ and 10 MΩ output loads, respectively. At 13.56 MHz the output voltage of the charge pump is three times higher than the output of a half-wave rectifier. The results demonstrate the possibility to print efficient high frequency (HF) charge pump circuits to meet the supply voltage requirements of the printed electronic applications.     

0.4-V bulk-driven differential-difference amplifier

A new solution for an ultra-low-voltage, low-power, bulk-driven fully differential-difference amplifier (FDDA) is presented in the paper. Simulated performance of the overall FDDA for a 50 nm CMOS process and supply voltage of 0.4 V, shows dissipation power of 31.8 μW, the open loop voltage gain of 58.6 dB and the gain-bandwidth product (GBW) of 2.3 MHz for a 20 pF load capacitance. Despite the very low supply voltage, the FDDA exhibits rail-to-rail input/output swing. The circuit performance has also been tested in two applications; the differential voltage follower and the second-order band-pass filter, showing satisfactory accuracy and dynamic range.     

A wideband balun–LNA

In this paper a wideband Low Noise Amplifier (LNA) is introduced which also converts the single-ended input to differential signal at the output. It is based on common-source amplifier with active-feedback to provide input matching. The proposed amplifier has the input matched from 500 MHz to 2.5 GHz. It achieves the maximum voltage gain of 24 dB in this band, while the minimum noise figure (NF) is 2.35 dB. The simulated OIP3 of this amplifier is equal to 21 dBm. The LNA has been designed and simulated in a 0.18 μm CMOS process.     

A high-performance 1.2 V–99 μW rail-to-rail CMOS class AB amplifier

This paper presents a compact, reliable 1.2 V low-power rail-to-rail class AB operational amplifier (OpAmp) suitable for integrated battery powered systems which require rail-to-rail input/output swing and high slew-rate while maintaining low power consumption. The OpAmp, fabricated in a standard 0.18 μm CMOS technology, exhibits 86 dB open loop gain and 97 dB CMRR. Experimental measurements prove its correct functionality operating with 1.2 V single supply, performing very competitive characteristics compared with other similar amplifiers reported in the literature. It has rail-to-rail input/output operation, 5 MHz unity gain frequency and a 3.15 V/μs slew-rate for a capacitive load of 100 pF, with a power consumption of 99 μW.     

A high-gain low-power 2–14 GHz ultra-wide-band CMOS LNA for wireless receivers

In this paper, a 2–14 GHz CMOS LNA for ultra-wide-band (UWB) wireless systems is presented. To achieve a good and flat high power gain along with a low noise figure and a high input return loss, the proposed LNA adopts a capacitive cross-coupling common-gate (CG) topology with extra cascaded transistors and inductance. Over the entire 2–14 GHz bandwidth, it exhibits a return loss less than ?10 dB and a small-signal gain of 9 dB. With an input intercept point of ?3 dBm at 5 GHz, it consumes only 9 mW from a 1.5 V supply voltage.     

Low power high gain CMOS LNA based on inverter cell and self-body bias for UWB receivers

A low-power low-noise amplifier (LNA) utilized a resistive inverter configuration feedback amplifier to achieve the broadband input matching purposes. To achieve low power consumption and high gain, the proposed LNA utilizes a current-reused technique and a splitting-load inductive peaking technique of a resistive-feedback inverter for input matching. Two wideband LNAs are implemented by TSMC 0.18 μm CMOS technology. The first LNA operates at 2–6 GHz. The minimum noise figure is 3.6 dB. The amplifier provides a maximum gain (S₂₁) of 18.5 dB while drawing 10.3 mW from a 1.5-V supply. This chip area is 1.028×0.921 mm². The second LNA operates at 3.1–10.6 GHz. By using self-forward body bias, it can reduce supply voltage as well as save bias current. The minimum noise figure is 4.8 dB. The amplifier provides a maximum gain (S₂₁) of 17.8 dB while drawing 9.67 mW from a 1.2-V supply. This chip area is 1.274×0.771 mm².     

Efficient biasing circuit strategies for inductorless wideband low noise amplifiers with feedback

This paper presents a comparative study among different biasing circuits of inductorless low-area Low Noise Amplifier (LNAs) with feedback. This study intends to determine the most suitable biasing circuit to achieve the best LNA performance for wideband applications. The main performance metrics are analyzed and a comparison is carried out based on electrical simulations. To this purpose, two different CMOS technology processes are considered: 130 nm and 90 nm. In both cases, the supply voltage is 1.2 V. The best LNA designed in 130 nm achieves a bandwidth of 2.94 GHz with a flat voltage gain (A_v) of 16.5 dB and a power consumption of 3.2 mW. The same LNA topology designed in 90 nm technology has a bandwidth of 11.2 GHz, featuring a voltage gain of 16.6 dB and consuming 1.9 mW. Both LNAs are input-impedance matched and have a noise figure below 2.4 dB measured at 2.4 GHz. As a case study, the layout of the best-performance LNA circuit has been implemented in a 130 nm technology, achieving an area of 0.012 mm², which is near the size of a pad or an inductor. It is demonstrated that the bandwidth of this circuit can be notably increased by simply adding a small inductance in the feedback path.¹     

A new CMOS differential current-mode AGC on the division operation based

A new CMOS differential current-mode AGC on the division operation based is presented. The operation principle consists in detection of both positive and negative envelopes of the differential input signal cycles, respectively. The output signal with constant magnitude is obtained by dividing the differential input signal to the difference between the positive and negative detected envelopes. The new current-mode architecture of the proposed AGC (composed only by an envelope detector and a divider stage) diminishes significantly the settling time, the circuit complexity and the power consumption. The circuit yields an input dynamic range of 15 dB and provides a constant magnitude output signal in the frequency range from 10 MHz to 70 MHz. The current consumption is 5 mA from a single 3.3 V supply voltage. The simulations performed in 0.13 µm CMOS process confirm the theoretically obtained results.     

A low-distortion multi-bit sigma–delta ADC with mismatch-shaping DACs for WLAN applications

A low-distortion feed-forward MASH2_4b-2_4b sigma–delta analog-to-digital converter (ADC) for wireless local area network (WLAN) applications was presented. The converter exhibits improved performances than the ADCs which have been presented to date by adding a feedback factor in the second stage and employing a 2nd-order noise-shaping dynamic element matching (DEM) scheme. The feedback factor induces a zero in the noise transfer function (NTF) and therefore improves the in-band signal to noise and distortion ratio (SNDR) of the modulator. The mismatch-shaping DEM was introduced and applied to the 4-bit DACs in this paper to improve the resolution and linearity of the ADC. Fabricated in a 0.18 μm CMOS process with single 1.8 V supply voltage, the converter achieves a peak SNDR of 85.4 dB over a 10 MHz bandwidth which implies an effective number of bits (ENOB) of 13.90-bit. The spurious free dynamic range (SFDR) is –94 dB for a 1.25 MHz@–6dBFS input signal at 160 MHz sampling frequency. The occupied area is 0.44 mm² and dissipation power 23.4 mW.     

An improved 860–960 MHz fully integrated CMOS power amplifier designation for UHF RFID transmitter

An improved design of 860–960 MHz fully integrated CMOS power amplifier (PA) for UHF RFID transmitter is presented in this paper. It utilizes three stage differential structure, including common-source structure applying RC feedback circuit to improve linearity, cascade structure adopting self-biased cascode technique and self-forward-body-bias (SFBB) technique to overcome shortcomings of low breakdown voltage and to reduce supply voltage respectively in order to obtain high output power, high efficiency and low supply voltage. By integrating these techniques organically, simulation results demonstrate that the circuit provides 21 dBm output power and 35% power-added efficiency (PAE) with 3 V supply. A comparison with other PAs operating in similar frequencies shows the proposed LNA has advantages of higher output power, higher PAE, higher linearity and lower supply voltage.     

A low-transconductance OTA with improved linearity suitable for low-frequency Gm-C filters

A fully differential operational transconductance amplifier is presented in this paper with enhanced linearity and low transconductance, suitable for low-frequency Gm-C filters. This paper also proposes a new common-mode feedback scheme that presents low sensitivity to large differential voltage swings at the OTA outputs. The proposed OTA was employed in the design of a fully-integrated Gm-C low-pass filter with a cutoff frequency of 30 kHz. The Gm-C filter was fabricated in a 0.35 μm CMOS technology and presented a THD at the output less than 1% for input signals with differential amplitudes up to 3.2 V.     

Low power high output impedance high bandwidth QFGMOS current mirror

Current mirror is a basic block of any mixed-signal circuit for example in an analog-to-digital converter. Its precise performance is the key requirement for analog circuits where offset is a measure issue. The key parameter which defines the performance of current mirror is its input/output impedance, input swing, and bandwidth. In this paper, a low power design of current mirror using quasi-floating gate MOS transistor is presented. The proposed current mirror boosts its output impedance in range of giga-ohm through use of regulated cascode structure followed by super-cascode. Another improvement is done in reduced input compliance voltage limits with the help of level shifter. The proposed current mirror operates well for input current range 0–700 $\mathrm{\mu }A$ with an input and output impedance of 160 $\Omega$ and 8.55 $\mathrm{G}\Omega$ respectively and high bandwidth of 4.05 $\mathrm{GHz}$. The total power consumption of the proposed current mirror is about 0.84 mW. The low power consumption with enhanced output impedance and bandwidth suits proposed current mirror for various high-speed analog designs. Performance of the presented current mirror circuit is verified using HSpice simulations on 0.18 $\mathrm{\mu }m$ mixed-mode twill-well technology at a supply voltage of ±0.5 V.     

On practical construction of electronically controllable compact current amplifier based on commercially available elements and its application

This paper presents a new concept of a current amplifier (CA) with electronically adjustable features (input resistance and current gain) implemented using commercially available devices. Several variations of basic structure are studied, described and the selected solutions verified by PSpice simulations and, moreover, also by lab experiments. Saving one discrete active device in comparison to already known similar topologies of single-input and single-output version (CA-SISO) is significant benefit whereas all other qualitative features remain very similar to previously reported ones. Simple modification of CA concept to multiple-output version (CA-SIMO), having independent adjustable current gain in each of output branches, is easily available. Experimental tests of features of discussed concepts yield adjustability range of input resistance from 100 Ω to more than 10 kΩ and current gain adjusting from 0.1 to 3.5 with bandwidth (−3 dB) of CA transfer response up to 16 MHz. As an example of application, proposed CA was successfully implemented in quadrature oscillator with a very wide tunability range from 29 kHz to 4.94 MHz. It was achieved by electronic control of several adjustable parameters of proposed CA.