碳化硅和氧化铝陶瓷的热等静压氮化

通过对无压烧结、热压烧结和热等静压烧结ＳＩＣ陶瓷以及热压烧结的ＳｉＣ粒子补强Ａｌ２Ｏ３基复相陶瓷（ＳｉＣｐ－Ａｌ２Ｏ３）和ＳｉＣ粒子与ＳｉＣ晶须共同增强的Ａｌ２Ｏ３基复合材料（ＳｉＣｐ－ＳｉＣｗ－Ａｌ２Ｏ３）在氮气氛中进行高温氮化处理，成功地实现了这些材料的开口气孔表面裂纹的愈合。研究表明：热等静压氯化工艺可以显著提高ＳｉＣ和Ａｌ２Ｏ３陶瓷的抗弯强度，对断裂韧性也有较大的改善作用。对于热等静压烧结ＳｉＣ陶瓷，在１８５０℃和２００ＭＰａ氮气压力下氯化处理１小时后，其抗弯强度和断裂韧性分别由５８２ＭＰａ和５．７ＭＰａ·ｍ１／２提高到９０７ＭＰａ和８．４ＭＰａ·ｍ１／２；对于热压烧结的ＳｉＣｐ－Ａｌ２Ｏ３复相陶瓷和ＳｉＣｐ－ＳｉＣｗ－Ａｌ２Ｏ３复合材料，在１７００℃和１５０ＭＰａ氮气压力下氮化处理１小时后，其室温抗弯强度分别由４６０和７０５ＭＰａ提高到８９５和１０３３ＭＰａ。     

晶种对自增韧Si3N4显微结构和性能的影响

采用热压烧结－高温气压处理的方法研究了棒状β－Ｓｉ３Ｎ４晶种对Ｌａ２Ｏ３－Ｙ２Ｏ３系自增韧Ｓｉ３Ｎ４显微结构和性能的影响。结果表明,加入晶种将在组织中引入粗大柱状β－Ｓｉ３Ｎ４晶粒,分布均匀;随着晶种加入量的增加,粗大柱状β－Ｓｉ３Ｎ４晶粒数量增加,组３织明显粗化。当晶种加入量较小时（１０ｖｏｌ％）,材料具有较高的断裂韧性（￣１２ＭＰａｍ＾１／２）,同时保持较高的强度（８００￣９００ＭＰａ）,而当晶种加入量较大时,则表现为抗弯强度的明显下降。分析表明,大晶粒直径及其面积百分数是影响断裂韧性的主要因素。     

SiO2-Si3N4复合材料的力学性能及其增韧机理

采用热压工艺制备了ＳｉＯ２－Ｓｉ３Ｎ４复合材料，其抗弯强度和断裂韧性达到１４３ＭＰａ和１．７ＭＰａ．ｍ＾１／２，比基体ＳｉＯ２材料分别提高１０７％和７０％，复合材料改善是由于高弹性模量的Ｓｉ３Ｎ４引入以及ＳｉＯ２和Ｓｉ３Ｎ４热膨胀系数不匹配导致的残余应力。     

SiC—AlN—Y2O3复相陶瓷的制备与性能

通过热压烧结技术，ＳｉＣ、ＡｌＮ和Ｙ２Ｏ３粉末混合体在１９２０￣２０５０℃、Ａｒ气氛下形成了致密的复相陶瓷。在室温下ＳｉＣ－ＡｌＮ－Ｙ２Ｏ３复相材料的抗弯强度和断裂韧性分别达到６００ＭＰａ和７ＭＰａ·ｍ＾１／２以上。运用ＸＲＤ、ＳＥＭ和ＴＥＭ分析致密样品的断裂裂纹、形貌和组成。ＳｉＣ－ＡｌＮ－Ｙ２Ｏ３复相陶瓷在１３７０℃氧化试验３０ｈ，其氧化产物为莫来石。     

三维碳化硅/碳化硅陶瓷基编织体复合材料

采用化学气相浸渗法（ＣＶＩ）,制备出三维Ｈｉ－ＮｉｃａｌｏｎＳｉＣ／ＳｉＣ陶瓷基编织体复合材料．经３０ｈ ＣＶＩ致密化处理后,复合材料的密度达到 ２５９·ｃｍ－３,所研制的三维 ＳｉＣ／ＳｉＣ复合材料不仅具有较高的强度,而且表现出优异的韧性和类似金属材料非灾难性的断裂特征．复合材料的主要力学性能指标为：弯曲强度 ８６０ＭＰａ,断裂位移 １．２ｍｍ,断裂韧性４１．５ＭＰａ·ｍ１／２,断裂功２８．１ｋＪ·ｍ－２,冲击韧性３６．０ｋＪ·ｍ－２．     

二价离子替代的Nasicon及其应用研究

含二价阳离子的Ｎａｓｉｃｏｎ，Ｍ￣（２＋）Ｎａｓｉｃｏｎ（Ｍ＝Ｍｇ、Ｃａ、Ｓｒ、Ｚｎ）可由母体Ｎａ＿３Ｚｒ＿２Ｓｉ＿２ＰＯ＿（１２）（Ｎａｓｉｃｏｎ）为起始原料与相应的二价离子的盐浓液或熔盐进行离子交换而制得。Ｘ射线衍射分析结果表明离子交换后的产物Ｍ￣（２＋）－Ｎａｓｉｃｏｎ大多保持原母体的Ｃ＿（２／ｃ）结构。交流阻抗技术测定的电导率数据显示含不同的二价替代离子的Ｎａｓｉｃｏｎ的电导率相差甚大。其中最好的是Ｍｇ￣（２＋）－Ｎａｓｉｃｏｎ，其电导率在４００℃时可达到１．４８×１０￣（－２）Ｓ／ｃｍ。Ｍｇ￣（２＋）－Ｎａｓｉｃｏｎ用作微功率固态电池Ｍｇ／ＣｕＣｌ的电解质，该电池的开路电压为２．０７Ｖ，短路电流为１ｍＡ。平均放电电压为１．６Ｖ，电池的放电容量是３．４ｍＡＨ。     

SiC－AlN－Y_2O_3复相陶瓷的制备与性能

通过热压烧结技术，ＳｉＣ、ＡｌＮ和Ｙ２Ｏ３粉末混合作在１９２０～２０５０℃、Ａｒ气氛下形成了致密的复相陶瓷．在室温下ＳｉＣ－ＡｌＮ－Ｙ２Ｏ３复相材料的抗弯强度和断裂韧性分别达到６００ＭＰａ和７ＭＰａ·ｍ１／２以上运用ＸＲＤ、ＳＥＭ和ＴＥＭ分析致密样品的断裂裂纹、形貌和组成．ＳｉＣ－ＡｌＮ－Ｙ２Ｏ３复相陶瓷在１３７０℃氧化试验３０ｈ，其氧化产物为莫来石．     

结构陶瓷的高温疲劳强度衰减理论

提出了陶瓷材料疲劳强度衰减理论并由此导出了各种疲劳关系式。建立了疲劳基本方程ｄσ＿ｒ／ｄ＿ｉ＝一Ａσ（ｔ）￣ｎｔ￣（－ｍ），得出了疲劳寿命公式Ｔ＝Ｍ（σ＿０－σ）／Ａσ￣ｎ（静疲劳时Ｍ＝１，连续增载疲劳时Ｍ＝ｎ＋１，循环疲劳时Ｍ＝（ｎ＋１）／（１＋Ｒ＋Ｒ￣２＋……＋Ｒ￣ｎ），逐级加载时，并导出不同疲劳方式下疲劳寿命间的关系。同时，用多种Ｓｉ＿３Ｎ＿４材料在高温中作了论证试验，结果与理论一致。     

Si3N4／SiC（n）／SiC（w）纳米复合材料力学性能研究

采用热压烧结工艺制备了纳米ＳｉＣ颗粒和ＳｉＣ晶须协同补强增韧的Ｓｉ３Ｎ４基纳米复合陶瓷材料,并对其微观结构和力学性能进行了研究。结果表明：该复合材料室温抗弯强度达１０８０ＭＰａ,断裂韧性Ｋ１ｃ值达１１．７ＭＰａｍ＾１／２。纳米ＳｉＣ颗粒和ＳｉＣ晶须对Ｓｉ３Ｎ４基体具有较好的协同补强增韧作用。     

常压烧结ZTM／Al2O3复合陶瓷的力学性能

采用干法成型、常压烧结工艺制得致密的ＺＴＭ／Ａｌ２Ｏ３复合陶瓷材料。通过引入大颗粒的氧化铝，使ＺＴＭ陶瓷（氧化锆增韧莫来石陶瓷）的力学性能有明显提高。组成２０Ｖｏｌ．％Ａｌ２Ｏ３－２０Ｖｏｌ．％ＺｒＯ２－ｍｕｌｌｉｔｅ陶瓷材料，其断裂韧性为６．０６ＭＰａ·ｍ＾１／２，抗弯强度为４０３ＭＰａ。实验结果表明：Ａｌ２Ｏ３的弥散强化和ＺｒＯ２的相变增韧及微裂纹增韧是ＺＴＭ／Ａｌ２Ｏ３陶瓷的主要增韧机理。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Synthesis of Alumina-Zirconia Nanocomposites by Solgel Process

Al₂O₃-ZrO₂ nanocomposites were developed starting with the solgel process. Composite alumina-zirconia nanopowders were synthesized from metallorganic precursors (Aluminium secondary butoxide and zirconium Iso propoxide) using the solgel process. The parameters affecting the synthesis—solvent, concentration of precursor, R/H ratio (i.e., dilution of water in solvent)—were varied as also the temperature and pH. BET and TEM were used to measure nanosize. Diffuse reflectance spectroscopy and also qualitative optical absorption led to identical particle size estimate. The variation of process parameters was used to study the effect and interdependence of process parameters. Artificial Neural Networks was used to rigorously analyze the process. Although this led to confirmation of interdependence of parameters, the presence of a single overwhelming solvent variable was also established. Then the optimal process was used to synthesize more nanopowder. To produce bulk nanocomposite the nanopowders were sintered by varying the temperature and time period. The sintered lithoids were probed with a vickers hardness tester to measure elastic modulus, hardness, and fracture toughness. The results showed high elastic modulus, modest hardness, and very high fracture toughness.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.