共查询到20条相似文献,搜索用时 93 毫秒
1.
本文指出了许多电热远红外烤漆设备采用调节加热器供电电压的方式来实现恒温控制,或采用改变被加热工件的辐照距离的方式来实现工件区域性恒温存在的缺点。以我们设计和研制的大型电热远红外烤漆烘房为例,证实了加热器采用恒压供电、烘房进行气体交换的自动恒温方式,以及对工件辐照距离、角度进行优选,更有利于发挥远红外辐射加热的特长和充分挖掘远红外辐射加热的潜力。 相似文献
2.
远红外加热是辐射加热,但又不是一般的辐射加热,两者区别在于,远红外加热关心的是辐射与吸收间良好的匹配,而一般辐 相似文献
3.
随着工农业的发展,使用远红外线进行加热,已经广泛深入地开展起来了。使用远红外线进行加热比传统的加热方式所呈现出的很多优点已为实践所证实,并为许多单位所采用。产生这些优点的原因,归纳起来就是:(1)把原加热设备的电热丝用一些旁热材料(例如碳化硅、氧化镁、锆英石等等)包起来,以期降低直接辐射表面的温度,从而使所辐射的红外线能量比起电热丝来,较多地集中在波长较长的红外区域。这就是所谓“远红外加热”名称的由来。(2)在这种加热元件的旁热材料表面上,再涂上一层辐射率较高的涂料,以期增加外加能源转换成红外线的转换效率。也就是说,在相同条件下,能够得到较多的红外线。(3)被加热工件在远红外波段范围内往往又有较好的吸收特性。根据(1)、(2)两点所述可知,辐射元件所辐射的红外线能够较多地集中在被加热工件吸收特性较好的波段范 相似文献
4.
5.
6.
俞福堂 《红外与毫米波学报》1983,2(4)
全书共分六章,分别阐述红外辐射的基础理论和应用理论、远红外辐射材料和器件、远红外烘炉设计、远红外辐射加热实例,书末附有大量参考数据和光谱图。本书可供从事红外辐射加热的科技人员参考。 相似文献
7.
大型客车车身涂装工艺过程中远红外加热技术的应用 总被引:1,自引:1,他引:0
通过在远红外辐射和空气对流加热条件下的对比测试,证明在大型客车车身涂装工艺过程中,采用远红外辐射的烘干方式,可以提高烘干质量并可取得明显的节能效果。 相似文献
8.
9.
远红外辐射涂层的研制 总被引:1,自引:0,他引:1
《红外技术》1980,(1)
一、前言加热和干燥工序是许多生产过程中不可缺少的环节。热能通常以传导、对流和辐射三种途径进行传递。由于辐射传热一般较快,加之许多有机高分子材料和含水物质对火于3微米波长的红外线(俗称远红外线,下同)的吸收比较强烈,因而采用远红外辐射加 相似文献
10.
远红外加热技术的核心,在于制造高效、耐用的远红外辐射器。本文介绍的HL型涂层,是以磷酸为主体,以氧化铜等化学物质为粘接剂,按比例加入一种或多种远红外辐射材料而制成的;SG-1型管是将HL型涂料涂于金属表面而制成的远红外辐射器。本文介绍了HL型涂层的制备和SG-1型管的制造和应用。涂层的辐射峰值波长在3.5—5.5μm之间。SG-1型管比碳化硅管,其升温时间快一倍,比不涂HL型涂料的铁管,节省电能约40%。 相似文献
11.
提高MCVD工艺单模光纤生产率的新技术 总被引:1,自引:0,他引:1
光通信迅速发展,对单模光纤的需求急剧增长,以传统的MCVD工艺生产单模光纤,生产率受到限制。本文首先简要分析了这些限制因素,然后综述克服这些限制因素的新技术,其中包括使用合成石英管,各种混合工艺以及可取代氩-氧焰的新加热技术。最后,对我国光纤制造业的发展提出了建议。 相似文献
12.
C. O. Jeong N. S. Roh S. G. Kim H. S. Park C. W. Kim D. S. Sakong J. H. Seok K. H. Chung W. H. Lee Dongwen Gan Paul S. Ho B. S. Cho B. J. Kang H. J. Yang Y. K. Ko J. G. Lee 《Journal of Electronic Materials》2002,31(6):610-614
The Ag-alloy films have been investigated as source/drain materials applicable to thin-film transistor liquid-crystal displays
(TFT-LCDs). The Ag-alloy consisting of 0.9at.%Pd, 1.7at.%Cu (designated APC) showed a resistivity that was lower than one-half
that of AlNd. It also had good contact characteristics with amorphous Si (a-Si). In addition, the Ag/Si was stable after heating
to above 700°C, requiring no diffusion barrier to prevent reaction between Ag and Si. Pure Ag films deposited on glass by
DC magnetron sputtering showed severe hillock formation, hole growth, and agglomeration upon annealing in air. In comparison,
the APC-alloy film exhibited improved resistance to agglomeration. Further, inverted-staggered back-channel-etch hydrogenated
amorphous silicon (a-Si:H) TFTs using an APC-alloy film as a source/drain material had a threshold voltage of 4 V. A structure
of single layers of gate-APC alloys and source/drain-APC alloys leads to lower costs and productivity improvements of large-area,
high-resolution, active-matrix LCDs, such as 40-in. size panels through process simplification. 相似文献
13.
14.
15.
A computer simulation of tissue heating is used to examine the heating pattern produced by a focused ultrasound transducer scanned over the tumor. It is shown that, a large area transducer is required to give preferential heating at depth and the heating pattern is not given by the path of the focal volume. The effect of varying the heating pattern with time by pulsing or scanning is investigated using an estimate of thermal dose which takes into account the. nonlinear dependence of heat damage on temperature, and it is found that temperature fluctuations tend to reduce the therapeutic ratio and so should be avoided. The implications of these results on the design of ultrasound heating systems are discussed. 相似文献
16.
近年来,微波加热以其高效性和内部加热等优点在各领域得到广泛应用。然而,微波加热的不均匀性限制了其大规模工业应用的发展。高均匀性和高效率是微波加热领域研究的重点。效率低会造成能源的浪费,而不均匀加热会导致加热品质差、甚至热失控等现象。本文提出一种双端口选频加热方法,通过在腔体中内置两个正交极化天线方式进行馈电。并且利用扫频来分析各频点的加热效率以及不同频率对加热效果的影响。最后选择性地对其中高效率的频点进行选频加热,使其在维持加热高效率的前提下提高加热的均匀性。 相似文献
17.
本文提出了一种计算电磁脉冲加热Debye媒质的快速算法。从麦克斯韦方程组和Debye方程出发,重新定义了Debye媒质中的瞬态耗散功率。该定义能有效避免传统定义中瞬态耗散功率为负的情况。通过时间尺度变换,把电磁场的计算和热场的计算统一到同一时间尺度下,这样就可以节省大量的计算时间。另外,研究了长时间脉冲加热的效率和均匀性。结果表明,在同样的重复频率下,脉冲加热的效率与均匀性均低于连续微波。 相似文献
18.
硅纳米线的固-液-固热生长及升温特性研究 总被引:4,自引:0,他引:4
该文报道一种直接在硅片上热生长硅纳米线的新方法。与传统的VLS生长机制不同,该方法在生长硅纳米线的过程中没有引入任何气态或液态硅源.是一种全新的固液固(SLS)生长机制。实验中使用了Ni,Au等金属作为催化剂,由Ar,H2等作为载流气体.系统压强为2.5104Pa,生长温度为950-1000℃.生长出的硅纳米线表面光滑,呈纯非晶态,直径为10-40 nm,长度可达数十微米,升温特性对硅纳米线SLS热生长起重要作用。研究了各项实验参数(包括气氛压强,加热温度及加热时间等)对硅纳米线生长的影响。 相似文献
19.
Tokunaga T Narushima T Yonezawa T Sudo T Okubo S Komatsubara S Sasaki K Yamamoto T 《Journal of electron microscopy》2012,61(4):223-227
The temperature distribution on a centre-holed thin foil of molybdenum, used as a sample and heated using a sample-heating holder for electron microscopy, was measured using an infrared thermal camera. The temperature on the heated foil area located near the heating stage of the heating holder is almost equal to the temperature on the heating stage. However, during the measurement of the temperature at the edge of the hole of the foil located farthest from the heating stage, a drop in temperature should be taken into consideration; however, so far, no method has been developed to locally measure the temperature distribution on the heated sample. In this study, a method for the accurate measurement of temperature distribution on heated samples for electron microscopy is discussed. 相似文献
20.
微波加热植物油的红外光谱分析 总被引:1,自引:0,他引:1
利用傅里叶变换红外光谱法并结合二维相关光谱技术对微波加热及传统加热下的三种植物油进行分析。对加热过程中红外光谱的峰位、峰形、峰强进行比较,一维红外光谱图没有明显的区别,而二维相关谱图中,同步、异步图差异比较明显。根据自动峰强度可比较同一植物油在不同加热方式下其分子结构变化的异同。另外与一维红外光谱相比,二维相关光谱的分辨率较高,在揭示分子内或分子间的相互作用研究中发挥了作用,增强了对谱图的识别能力。初步实验表明微波加热与传统加热过程中,植物油的分子结构变化是不一样的。 相似文献