Partial Oxidation of Methane to Syngas in a Packed Bed Catalyst Membrane Reactor

The planar membrane reactor configuration was explored for partial oxidation of methane (POM) to syngas. A supported membrane composed of yttria‐stabilized zirconia and La_0.8Sr_0.2Cr_0.5Fe_0.5O_3‐δ was sealed to a stainless holder, and a Ni/Al₂O₃ catalyst bed was placed under the membrane plane with a small slit between them. This reactor configuration would facilitate the POM reaction via oxidation‐reforming mechanism: the oxidation reaction occurring at the membrane surface and the reforming reaction taking place in the catalyst bed. At 800°C and a methane feed rate of 32 mL min^?1, the reactor attained methane throughput conversion over 90%, CO and H₂ selectivity both over 95%, and an equivalent oxygen permeation rate 1.4 mL cm^?2 min^?1. The membrane and catalyst remained intact after the POM testing. The planar membrane reactor configuration explored in this study may lead to the development of a compact reactor for syngas production. © 2016 American Institute of Chemical Engineers AIChE J, 62: 2170–2176, 2016     

A novel porous‐dense dual‐layer composite membrane reactor with long‐term stability

A porous‐dense dual‐layer composite membrane reactor was proposed. The dual‐layer composite membrane composed of dense 0.5 wt % Nb₂O₅‐doped SrCo_0.8Fe_0.2O_3‐δ (SCFNb) layer and porous Ba_0.3Sr_0.7Fe_0.9Mo_0.1O_3‐δ (BSFM) layer was prepared. The stability of SCFNb membrane reactor was improved significantly by the porous‐dense dual‐layer design philosophy. The porous BSFM surface‐coating layer can effectively reduce the corrosion of the reducing atmosphere to the membrane, whereas the dense SCFNb layer permeated oxygen effectively. Compared with single‐layer dense SCFNb membrane reactor, no degradation of performance was observed in the dual‐layer membrane reactor under partial oxidation of methane during continuously operating for 1500 h at 850°C. At 900°C, oxygen flux of 18.6 mL (STP: Standard Temperature and Pressure) cm^?2 min^?1, hydrogen production of 53.67 mL (STP) cm^?2 min^?1, CH₄ conversion of 99.34% and CO selectivity of about 94% were achieved. © 2013 American Institute of Chemical Engineers AIChE J, 59: 4355–4363, 2013     

Carbon dioxide separation and dry reforming of methane for synthesis of syngas by a dual‐phase membrane reactor

High‐temperature CO₂ selective membranes offer potential for use to separate flue gas and produce a warm, pure CO₂ stream as a chemical feedstock. The coupling of separation of CO₂ by a ceramic–carbonate dual‐phase membrane with dry reforming of CH₄ to produce syngas is reported. CO₂ permeation and the dry reforming reaction performance of the membrane reactor were experimentally studied with a CO₂–N₂ mixture as the feed and CH₄ as the sweep gas passing through either an empty permeation chamber or one that was packed with a solid catalyst. CO₂ permeation flux through the membrane matches the rate of dry reforming of methane using a 10% Ni/γ‐alumina catalyst at temperatures above 750°C. At 850°C under the reaction conditions, the membrane reactor gives a CO₂ permeation flux of 0.17 mL min^?1 cm^?2, hydrogen production rate of 0.3 mL min^?1 cm^?2 with a H₂ to CO formation ratio of about 1, and conversion of CO₂ and CH₄, respectively, of 88.5 and 8.1%. © 2013 American Institute of Chemical Engineers AIChE J, 59: 2207–2218, 2013     

High‐rate hydrogen separation using an MIEC oxygen permeable membrane reactor

In this study, we propose using mixed ionic‐electronic conducting (MIEC) oxygen permeable membrane to separate hydrogen via the water splitting reaction. To do that, steam was fed to one side of the membrane (side I) and a low‐purity hydrogen was fed to the other side (side II). Oxygen from water splitting on side I permeates through the membrane driven by an oxygen chemical potential gradient across the membrane to react with the low‐purity hydrogen on side II. After condensation and drying, high‐purity hydrogen is acquired from side I. Thus, the hydrogen separation process is realized based on the fact that the low‐purity hydrogen is consumed and high‐purity hydrogen is acquired. We achieved a high hydrogen separation rate (13.5 mL cm^?2 min^?1) at 950°C in a reactor equipped with a 0.5‐mm‐thick Ba_0.98Ce_0.05Fe_0.95O_3‐δ membrane. This research proofed that it is feasible to upgrade hydrogen purity using an MIEC oxygen permeable membrane. © 2016 American Institute of Chemical Engineers AIChE J, 63: 1278–1286, 2017     

Design of mixed conducting ceramic membranes/reactors for the partial oxidation of methane to syngas

The performance of mixed conducting ceramic membrane reactors for the partial oxidation of methane (POM) to syngas has been analyzed through a two‐dimensional mathematical model, in which the material balance, the heat balance and the momentum balance for both the shell and the tube phase are taken into account. The modeling results indicate that the membrane reactors have many advantages over the conventional fixed bed reactors such as the higher CO selectivity and yield, the lower heating point and the lower pressure drop as well. When the methane feed is converted completely into product in the membrane reactors, temperature flying can take place, which may be restrained by increasing the feed flow rate or by lowering the operation temperature. The reaction capacity of the membrane reactor is mainly determined by the oxygen permeation rate rather than by the POM reaction rate on the catalyst. In order to improve the membrane reactor performance, reduction of mass transfer resistance in the catalyst bed is necessary. Using the smaller membrane tubes is an effective way to achieve a higher reaction capacity, but the pressure drop is a severe problem to be faced. The methane feed velocity for the operation of mixed conducting membrane reactors should be carefully regulated so as to obtain the maximum syngas yield, which can be estimated from their oxygen permeability. The mathematical model and the kinetic parameters have been validated by comparing modeling results with the experimental data for the La_0.6Sr_0.4Co_0.2Fe_0.8O_3‐α (LSCF) membrane reactor. © 2009 American Institute of Chemical Engineers AIChE J, 2009     

Evaluation of mixed‐conducting lanthanum‐strontium‐cobaltite ceramic membrane for oxygen separation

In this study, La_0.4Sr_0.6CoO_3‐δ (LSC) oxide was synthesized via an EDTA‐citrate complexing process and its application as a mixed‐conducting ceramic membrane for oxygen separation was systematically investigated. The phase structure of the powder and microstructure of the membrane were characterized by XRD and SEM, respectively. The optimum condition for membrane sintering was developed based on SEM and four‐probe DC electrical conductivity characterizations. The oxygen permeation fluxes at various temperatures and oxygen partial pressure gradients were measured by gas chromatography method. Fundamental equations of oxygen permeation and transport resistance through mixed conducting membrane were developed. The oxygen bulk diffusion coefficient (D_v) and surface exchange coefficient (K_ex) for LSC membrane were derived by model regression. The importance of surface exchange kinetics at each side of the membrane on oxygen permeation flux under different oxygen partial pressure gradients and temperatures were quantitatively distinguished from the oxygen bulk diffusion. The maximum oxygen flux achieved based on 1.6‐mm‐thick La_0.4Sr_0.6CoO_3‐δ membrane was ～4.0 × 10^?7 mol cm^?2 s^?1at 950°C. However, calculation results show theoretical oxygen fluxes as high as 2.98 × 10^?5 mol cm^?2 s^?1 through a 5‐μm‐thick LSC membrane with ideal surface modification when operating at 950°C for air separation. © 2009 American Institute of Chemical Engineers AIChE J, 2009     

Einsatz von perowskitischen Hohlfasermembranen in einem Mikrowellenplasma

For the first time the combination of a separation process with a plasma process was successfully tested. In this case, a mixed‐conducting perovskite membrane separates the oxygen. At 1 kW a permeation of 2.24 mL min^?1cm^?2 could be achieved. Corresponding perovskite membranes have been manufactured as hollow fibers with a very good CO₂ stability. The hollow fibers showed a constant permeation over more than 200 h. Furthermore, a spinning process with a sulphur‐free polymer binder has been established.     

Partial oxidation of methane in BaCe0.1Co0.4Fe0.5O3−δ membrane reactor

A new perovskite material, BaCe_0.1Co_0.4Fe_0.5O_3?δ used as dense oxygen permeable membrane for partial oxidation of methane (POM) reaction was investigated. In order to improve the synergetic effects between membrane and catalyst, LiLaNiO/γ-Al₂O₃ catalyst was directly packed onto the surface of the membrane to carry out POM. In BaCe_0.1Co_0.4Fe_0.5O_3?δ membrane reactor, high oxygen permeation flux, high CH₄ conversion and CO selectivity were obtained. At 950 °C, oxygen flux of 9.5 ml cm^?2 min^?1, CH₄ conversion of 99% and CO selectivity of 93% were achieved with a membrane thickness of 1.0 mm. There was an induction process at the initial stage of POM, which was related to the reduction of NiO to Ni⁰ in LiLaNiO/γ-Al₂O₃ catalyst. Experiments illustrated that higher reaction temperature would shorten the induction time. During continuously operating for 1000 h at 875 °C, no degradation of performance of the membrane reaction was observed. SEM characterization also demonstrated that the membrane disc maintained an integral structure without any cracks after long-term operation.     

Partial oxidation of methane in hollow‐fiber membrane reactors based on alkaline‐earth metal‐free CO2‐tolerant oxide

The U‐shaped alkaline‐earth metal‐free CO₂‐stable oxide hollow‐fiber membranes based on (Pr_0.9La_0.1)₂(Ni_0.74Cu_0.21Ga_0.05)O_4+δ (PLNCG) are prepared by a phase‐inversion spinning process and applied successfully in the partial oxidation of methane (POM) to syngas. The effects of temperature, CH₄ concentration and flow rate of the feed air on CH₄ conversion, CO selectivity, H₂/CO ratio, and oxygen permeation flux through the PLNCG hollow‐fiber membrane are investigated in detail. The oxygen permeation flux arrives at approximately 10.5 mL/min cm² and the CO selectivity is higher than 99.5% with a CH₄ conversion of 97.0% and a H₂/CO ratio of 1.8 during 140 h steady operation. The spent hollow‐fiber membrane still maintains a dense microstructure and the Ruddlesden‐Popper K₂NiF₄‐type structure, which indicates that the U‐shaped alkaline‐earth metal‐free CO₂‐tolerant PLNCG hollow‐fiber membrane reactor can be steadily operated for POM to syngas with good performance. © 2014 American Institute of Chemical Engineers AIChE J, 60: 3587–3595, 2014     

基于Ba-Ce-Co-Fe-O膜反应器的甲烷部分氧化反应研究

为开发稳定性和透氧量俱佳并适用于甲烷部分氧化反应(POM)的透氧膜材料,采用溶胶凝胶工艺合成了具有纯相钙钛矿结构的BaCe0.1Co0.4Fe0.5O3-δ混合导体陶瓷材料。POM操作结果表明:BaCe0.1Co0.4Fe0.5O3-δ膜反应器透氧量高于同类材料,875℃时透氧量达到了8.9 mL/(cm2.m in)。在1 000 h寿命实验中,膜反应器各项反应指标没有出现任何衰减,反应性能稳定,甲烷转化率和CO的选择性都在97%以上。SEM表征表明,反应后膜片表面微观结构的变化虽然不可避免,但是其仍然保持比较完整的结构。因此,该材料良好的透氧量和稳定性说明其具有较好的应用前景。     

Oxygen permeability and structural stability of a novel tantalum‐doped perovskite BaCo0.7Fe0.2Ta0.1O3−δ

Dense BaCo_0.7Fe_0.2Ta_0.1O_3?δ (BCFT) perovskite membranes were successfully synthesized by a simple solid state reaction. In situ high‐temperature X‐ray diffraction indicated the good structure stability and phase reversibility of BCFT at high temperatures. The thermal expansion coefficient (TEC) of BCFT was determined to amount 1.02 × 10^?5 K^?1, which is smaller than those of Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3?δ (BSCF) (1.15 × 10^?5 K^?1), SrCo_0.8Fe_0.2O_3?δ (SCF) (1.79 × 10^?5 K^?1), and BaCo_0.4Fe_0.4Zr_0.2O_3?δ (BCFZ) (1.03 × 10^?5 K^?1). It can be seen that the introduction of Ta ions into the perovskite framework could effectively lower the TEC. Thickness dependence studies of oxygen permeation through the BCFT membrane indicated that the oxygen permeation process was controlled by bulk diffusion. A membrane reactor made from BCFT was successfully operated for the partial oxidation of methane to syngas at 900°C for 400 h without failure and with the relatively high, stable oxygen permeation flux of about 16.8 ml/min cm². © 2009 American Institute of Chemical Engineers AIChE J, 2010     

钙钛矿型混合导体透氧膜SrFe0.6Cu0.3Ti0.1O3－δ的制备与表征

Dense membrane with the composition of SrFe0.6Cu0.3Ti0.1O3-δ （SFCTO） was prepared by solid state reaction method. Oxygen permeation flux through this membrane was investigated at operating temperature ranging from 750℃ to 950℃ and different oxygen partial pressure. XRD measurements indicated that the compound was able to form single-phased perovskite structure in which part of Fe was replaced by Cu and Ti. The oxygen desorption and the reducibility of SFCTO powder were characterized by thermogravimetric analysis and temperature programmed reduction analysis, respectively. It was found that SFCTO had good structure stability under low oxygen pressure at high temperature. The addition of Ti increased the reduction temperature of Cu and Fe. Performance tests showed that the oxygen permeation flux through a 1.5 mm thick SFCTO membrane was 0.35-0.96 ml·min ^-1·cm^-2 under air/helium oxygen partial pressure gradient with activation energy of 53.2 kJ·mol^-1. The methane conversion of 85%, CO selectivity of 90% and comparatively higher oxygen permeation flux of 5 ml·min^-1·cm^- 2 were achieved at 850℃, when a SFCTO membrane reactor loaded with Ni-Ce/Al2O3 catalyst was applied for the partial oxidation of methane to syngas.     

Novel and Ideal Zirconium-Based Dense Membrane Reactors for Partial Oxidation of Methane to Syngas

A novel and ideal dense catalytic membrane reactor for the reaction of partial oxidation of methane to syngas (POM) was constructed from the stable mixed conducting perovskite material of BaCo_0.4Fe_0.4Zr_0.2O_3– and the catalyst of LiLaNiO/-Al₂O₃. The POM reaction was performed successfully. Not only was a short induction period of 2 h obtained, but also a high catalytic performance of 96–98% CH₄ conversion, 98–99% CO selectivity and an oxygen permeation flux of 5.4–5.8 mlcm^–2min^–1 (1.9–2.0 molm^–2S^–1Pa^–1) at 850°C were achieved. Moreover, the reaction has been steadily carried out for more than 2200 h, and no interaction between the membrane material and the catalyst took place.     

Oxygen permeation through a CO2‐tolerant mixed conducting oxide (Pr0.9La0.1)2(Ni0.74Cu0.21Ga0.05)O4+δ

A novel K₂NiF₄‐type oxide based on (Pr_0.9La_0.1)₂(Ni_0.74Cu_0.21Ga_0.05)O_4+δ (PLNCG) dense mixed conducting ceramic membrane was successfully prepared through a sol–gel route. The oxygen permeation flux through the membrane swept by pure CO₂ was comparative to that swept by He. The oxygen permeation and the stability of PLNCG under pure CO₂ were investigated in detail. A membrane with a thickness of 0.8 mm was steadily operated for 230 h with a constant oxygen permeation flux of 0.32 mL/(min cm²) at 975^°C using pure CO₂ as sweep gas. X‐ray diffraction shows that PLNCG can maintain its fluorite phase, and no carbonates were observed, even when it was exposed to pure CO₂ for a long time. © 2011 American Institute of Chemical Engineers AIChE J, 58: 2473–2478, 2012     

La0.6Sr0.4Co0.8Ga0.2O3‐δ (LSCG) hollow fiber membrane reactor: Partial oxidation of methane at medium temperature

In this study, La_0.6Sr_0.4Co_0.8Ga_0.2O_3‐δ (LSCG) hollow fiber membrane reactor was integrated with Ni/LaAlO₃‐Al₂O₃ catalyst for the catalytic partial oxidation of methane (POM) reaction. The process was successfully carried out in the medium temperature range (600–800°C) for reaction of blank POM with bare membrane, catalytic POM reaction and swept with H₂:CO gas mixture. For the catalytic POM reaction, enhancement in selectivity to H₂ and CO is obtained between 650–750°C when O₂:CH₄ <1. High CH₄ conversion of 97% is achieved at 750°C with corresponding H₂ and CO selectivity of about 74 and 91%. The oxygen flux of the membranes also increased with the increase in oxygen partial pressure gradient across the membrane. The postreacted membranes were tested via XRD and FESEM‐EDX for their crystallinity and surface morphology. XPS analysis was further used to investigate the O1s, Co 2p and Sr 3d binding energies of the segregated elements from the reducing reaction environment. © 2013 American Institute of Chemical Engineers AIChE J, 59: 3874–3885, 2013     

Performance of Ba0.5Sr0.5Co0.8Fe0.2O3 + δ membrane after laser ablation for methane conversion

A cross-shaped pattern was formed on the surface of Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3 − δ oxygen permeation membrane by laser ablation. A membrane reactor made from this membrane was operated for partial oxidation of methane to syngas in the presence of Ni/ZrO₂ catalyst. The CH₄ conversion and CO selectivity of the membrane reactor were 98.8% and 91.5%, respectively, and the oxygen permeation flux through the membrane was 11.0 ml/cm² min at 850 °C. The effects of space velocity (SV) on CH₄ conversion and CO selectivity in such reactor were discussed. The mechanism of POM in such membrane reactor may follow the combustion and reforming mechanism.     

High CO2 resistance of indium-doped cobalt-free 60 wt.%Ce0.9Pr0.1O2-δ-40 wt.%Pr0.6Sr0.4Fe1-xInxO3-δ oxygen transport membranes

The oxygen transport membrane (OTM) has huge application prospects in gas separation and carbon neutralization based on oxygen enriched combustion. In this paper, the family 60 wt.%Ce_0.9Pr_0.1O_2-δ-40 wt.%Pr_0.6Sr_0.4Fe_1-xIn_xO_3-δ (CPO-PSF_1-xI_xO, x = 0.01, 0.025, 0.05, 0.075, 0.1) cobalt-free dual-phase MIEC OTMs doped with indium have been successfully prepared by Pechini method. The phase structure, surface morphology, element distribution, oxygen permeability, and long-term operation stability of these OTMs are systematically explored. Among these OTMs, the champion oxygen permeable flux of CPO-PSF_0.99I_0.01O reaches 1.07 mL min^?1·cm^?2 and 0.80 mL min^?1·cm^?2 at 1000 °C under air/He gradient and air/CO₂ gradient. Meanwhile, CPO-PSF_0.99I_0.01O maintains the value of 0.80 mL min^?1·cm^?2 steadily at 1000 °C for 100 h when pure CO₂ as the sweep gas. The surface element distribution and phase structure of the OTMs after long-term oxygen permeability reaction are investigated by XRD, SEM combining with EDS, where the spent membranes retain the same structure and component as the fresh membranes, demonstrating that the In-doped OTMs have an excellent CO₂ tolerance. Suitable indium substitution for iron of these OTMs not only improves the oxygen permeability, but also maintains the long-term reaction stability of the material.     

Performance of an oxygen-permeable membrane reactor for partial oxidation of methane in coke oven gas to syngas

Perovskite-type oxygen-permeable membrane reactors of BaCo_0.7Fe_0.2Nb_0.1O_3−δ packed with Ni-based catalyst had high oxygen permeability and could be used for syngas production by partial oxidation of methane in coke oven gas (COG). The BCFNO membrane itself had a poor catalytic activity to partial oxidation of CH₄ in COG. After the catalyst was packed on the membrane surface, 92% of methane conversion, 90% of H₂ selectivity, 104% of CO selectivity and as high as 15 ml/cm²/min of oxygen permeation flux were obtained at 1148 K. During continuously operating for 550 h at 1148 K, no degradation of performance of the BCFNO membrane reactor was observed under the condition of hydrogen-rich COG. The possible reaction pathways were proposed to be an oxidation-reforming process. The oxidation of H₂ in COG with the surface oxygen on the permeation side improves the oxygen flux through the membrane, and H₂O reacts with CH₄ by reforming reactions to form H₂ and CO.     

Partial oxidation of methane to syngas in BaCe0.15Fe0.85O3−δ membrane reactors

Dense planar Ba_0.15Ce_0.85FeO_3−δ (BCF1585) membrane reactors were investigated to produce syngas from methane. Firstly, the membrane itself catalytic activity to methane was investigated using a blank BCF1585 without any catalysts. Then a LiLaNi/γ-Al₂O₃ catalyst was packed on the BCF1585 membrane surface to test the synergetic effects of the membrane and catalyst. It was found that the membrane itself has a poor catalytic activity to methane. The main products are CO₂ and C₂, and methane conversion is low due to the low oxygen permeation flux. However, after the catalyst was packed on the membrane surface, both methane conversion and oxygen permeation flux were greatly improved by the synergetic effect between the membrane and catalyst. Carbon monoxide selectivity reached at 96% with methane conversion of up to 96%. The oxygen permeation flux reached at 3.0 mL/cm² min at 850 °C for a 1.5 mm disk membrane and can effectively be increased by reducing the thickness of the membranes. After operation for 140 h at 850 °C, the used membrane was examined with SEM and EDXS. The results revealed that the decomposition of the membrane materials could not be avoided under such conditions. Oxygen partial pressure gradient across the membranes is suggested as a critical factor to accelerate the kinetic decomposition of the materials.     

Improving the POM performance of YBa2Cu3O7−δ membrane reactor by Co doping

The performance of Co doped YBa₂Cu₃O_7−δ (YBCO) membrane reactor have been investigated in a process of the partial oxidation of methane (POM) to syngas. The results shows that doping YBCO membrane with a little Co can enhance its oxygen permeation flux and improve its stability in reducing atmosphere noticeably. At 900 °C, with feed flow at 50 ml/min, CH₄ 6.0 v%, SV = 12,000 h⁻¹, and Ni/ZrO₂ catalyst, CH₄ conversion rate, CO selectivity, and oxygen permeation flux can reach to 98%, 92% and 1.41 ml min⁻¹ cm⁻² respectively.