Surface Tensions of Carbonated 2‐Amino‐2‐methyl‐1‐propanol and Piperazine Aqueous Solutions

Surface tensions of carbonated 2‐amino‐2‐methyl‐1‐propanol (AMP) and piperazine (PZ) aqueous solutions were measured by a surface tension meter which employs the Wilhemy plate principle. A thermodynamic model was proposed to correlate the surface tensions of both CO₂‐unloaded and CO₂‐loaded aqueous solutions by introducing the contribution of CO₂ loading into the formulation of surface tension. Based on experiments and calculations, the effects of temperature, mass fractions of amines, and CO₂ loading on surface tensions of carbonated aqueous solutions were demonstrated.     

Kinetics of CO2 absorption into a novel 1‐diethylamino‐2‐propanol solvent using stopped‐flow technique

A stopped‐flow apparatus was used to measure the kinetics of carbon dioxide (CO₂) absorption into aqueous solution of 1‐diethylamino‐2‐propanol (1DEA2P) in terms of observed pseudo‐first‐order rate constant (k_o) and second‐order reaction rate constant (k₂), in this work. The experiments were conducted over a 1DEA2P concentration range of 120–751 mol/m³, and a temperature range of 298–313 K. As 1DEA2P is a tertiary amine, the base‐catalyzed hydration mechanism was, then, applied to correlate the experimental CO₂ absorption rate constants obtained from stopped‐flow apparatus. In addition, the pK_a of 1DEA2P was experimentally measured over a temperature range of 278–333 K. The Brønsted relationship between reaction rate constant (obtained from stopped‐flow apparatus) and pK_a was, then, studied. The results showed that the correlation based on the Brønsted relationship performed very well for predicting the absorption rate constant with an absolute average deviation of 5.2%, which is in an acceptable range of less than 10%. © 2014 American Institute of Chemical Engineers AIChE J, 60: 3502–3510, 2014     

Reaction kinetics of 2‐((2‐aminoethyl) amino) ethanol in aqueous and non‐aqueous solutions using the stopped‐flow technique

Observed pseudo‐first‐order rate constants (k_o) for the reaction between CO₂ and 2‐((2‐aminoethyl) amino) ethanol (AEEA) were measured using the stopped‐flow technique in an aqueous system at 298, 303, 308 and 313 K, and in non‐aqueous systems of methanol and ethanol at 293, 298, 303 and 308 K. Alkanolamine concentrations ranged from 9.93 to 80.29 mol m^?3 for the aqueous system, 29.99–88.3 mol m^?3 for methanol and 44.17–99.28 mol m^?3 for ethanol. Experimentally obtained rate constants were correlated with two mechanisms. For both the aqueous‐ and non‐aqueous‐AEEA systems, the zwitterion mechanism with a fast deprotonation step correlated the data well as assessed by the reported statistical analysis. As expected, the reaction rate of CO₂ in the aqueous‐AEEA system was found to be much faster than in methanol or ethanol. Compared to other promising amines and diamines studied using the stopped‐flow apparatus, the pseudo‐first‐order reaction rate constants were found to obey the following order: PZ (cyclic‐diamine) > EDA (diamine) > AEEA (diamine) > 3‐AP (primary amine) > MEA (primary amine) > EEA (primary amine) > MO (cyclic‐amine). The reaction rate constant of CO₂ in aqueous‐AEEA was double that in aqueous‐MEA, and the difference increased with an increase in concentration. All reaction orders were practically unity. With a higher capacity for carbon dioxide and a higher reaction rate, AEEA could have been a good substitute to MEA if not for its high thermal degradation. AEEA kinetic behaviour is still of interest as a degradation product of MEA. © 2012 Canadian Society for Chemical Engineering     

Vapour–liquid equilibrium of CO2 in aqueous solutions of N‐methyl‐2‐ethanolamine

The equilibrium solubility of CO₂ into aqueous solution of sterically hindered N‐methyl‐2‐ethanolamine or methyl amino ethanol (MAE) was investigated in the temperature range of 303.1–323.1 K and total CO₂ pressure in the range of 1–350 kPa. The N‐methyl‐2‐ethanolamine aqueous solutions studied were 0.968, 1.574, 2.240 and 3.125 mol kg^?1 of solvent. © 2011 Canadian Society for Chemical Engineering     

Salting‐out of acetone, 1‐butanol,and ethanol from dilute aqueous solutions

The salting‐out phase equilibria for acetone, 1‐butanol, and ethanol (ABE) from dilute aqueous solutions using potassium carbonate (K₂CO₃) and dipotassium hydrogen phosphate trihydrate (K₂HPO₄?3H₂O) as outstanding salting‐out agents were investigated. Increasing the salt concentration strengthened the salting‐out effects and improved the distribution coefficients of all three solvents (ABE) significantly. Temperature had a slight effect on the phase equilibria. The K₂HPO₄ solution (69 wt %) showed a stronger salting‐out effect than the K₂CO₃ solution (56 wt %) on recovering ABE from dilute aqueous solutions. Dilute aqueous solutions containing more solvents increased the recoveries of acetone and 1‐butanol, while the results showed a negligible effect on the solubility of ABE. The solubility of ABE was also correlated well with the molar number of salt per gram of water in the aqueous phase. A new equation demonstrated this satisfactorily. © 2015 American Institute of Chemical Engineers AIChE J, 61: 3470–3478, 2015     

Kinetics of the absorption of carbon dioxide into mixed aqueous solutions of 2-amino-2-methyl-l-propanol and piperazine

The reaction kinetics of the absorption of CO₂ into aqueous solutions of piperazine (PZ) and into mixed aqueous solutions of 2-amino-2-methyl-l-propanol (AMP) and PZ were investigated by wetted wall column at 30-40 °C. The physical properties such as density, viscosity, solubility, and diffusivity of the aqueous alkanolamine solutions were also measured. The N₂O analogy was applied to estimate the solubilities and diffusivities of CO₂ in aqueous amine systems. Based on the pseudo-first-order for the CO₂ absorption, the overall pseudo first-order reaction rate constants were determined from the kinetic measurements. For CO₂ absorption into aqueous PZ solutions, the obtained second-order reaction rate constants for the reaction of CO₂ with PZ are in a good agreement with the results of Bishnoi and Rochelle (Chem. Eng. Sci. 55 (2000) 5531). For CO₂ absorption into mixed aqueous solutions of AMP and PZ, it was found that the addition of small amounts of PZ to aqueous AMP solutions has significant effect on the enhancement of the CO₂ absorption rate. For the CO₂ absorption reaction rate model, a hybrid reaction rate model, a second-order reaction for the reaction of CO₂ with PZ and a zwitterion mechanism for the reaction of CO₂ with AMP was used to model the kinetic data. The overall absolute percentage deviation for the calculation of the apparent rate constant k_app is 7.7% for the kinetics data measured. The model is satisfactory to represent the CO₂ absorption into mixed aqueous solutions of AMP and PZ.     

Versatile Synthesis of Pyrrole‐2‐acetic Esters and (Pyridine‐2‐one)‐3‐acetic Amides by Palladium‐Catalyzed,Carbon Dioxide‐Promoted Oxidative Carbonylation of (Z)‐(2‐En‐4‐ynyl)amines

The oxidative carbonylation of readily available (Z)‐(2‐en‐4‐ynyl)amines, catalyzed by the PdI₂‐KI system, selectively afforded in satisfactory yields (40–95 %) either pyrrole‐2‐acetic ester or (pyridine‐2‐one)‐3‐acetic amide derivatives, depending on the susbtitution pattern of the substrate and the reaction conditions. The presence of an excess of carbon dioxide proved in most cases to be beneficial to both the reaction rate and product selectivity.     

CO2‐Alkanolamine Reaction Kinetics: A Review of Recent Studies

Alkanolamines are the most popular absorbents used to remove CO₂ from process gas streams. Therefore, the CO₂ reaction with alkanolamines is of considerable importance. The aim of this article is to provide an overview on the kinetics of the reaction of CO₂ with aqueous solutions of alkanolamines. The various reaction mechanisms that are used to interpret experimental kinetic data – zwitterion, termolecular and base‐catalyzed hydration – are discussed in detail. Recently published data on reaction kinetics of individual amine systems and their mixtures are considered. In addition, the kinetic behavior of several novel amine‐based solvents that have been proposed in the literature is analyzed. Generally, the reaction of CO₂ with primary, secondary and sterically hindered amines is governed by the zwitterion mechanism, whereas the reaction with tertiary amines is described by the base‐catalyzed hydration of CO₂.     

The analysis of solubility,absorption kinetics of CO2 absorption into aqueous 1‐diethylamino‐2‐propanol solution

In this present work, the CO₂ absorption performance of aqueous 1‐diethylamino‐2‐propanol (1DEA2P) solution was studied with respect to CO₂ equilibrium solubility, absorption kinetics, and absorption heat. The equilibrium solubility of CO₂ in 2M 1DEA2P solution was measured over the temperature range from 298 to 333 K and CO₂ partial pressure range from 8 to101 kPa. The absorption kinetics data were developed and analyzed using the base‐catalyzed hydration mechanism and artificial neural network models (radial basis function neural network [RBFNN] and back‐propagation neural network [BPNN] models) with an acceptable absolute average deviation of 10% for base‐catalyzed hydration mechanism, 2.6% for RBFNN model and 1.77% for BPNN model, respectively. The CO₂ absorption heat of 1DEA2P was estimated to be ?43.6 kJ/mol. In addition, the ions (1DEA2P, 1DEA2PH⁺, , CO₃^2?) speciation plots of the 1DEA2P‐CO₂‐H₂O system were developed to further understand the reaction process of 1DEA2P with CO₂. Based on a comparison with conventional amines (e.g., MEA, DEA, MDEA) and alternative amines (i.e., 1DMA2P and 4‐(diethylamino)?2‐butanol [DEAB]), 1DEA2P exhibited good performance with respect to CO₂ equilibrium solubility, reaction kinetics, and CO₂ absorption heat. Meanwhile, the overall evaluation of 1DEA2P for application in CCS in terms of absorption and desorption is presented, giving helpful information for the screening of these novel amines. © 2017 American Institute of Chemical Engineers AIChE J, 63: 2694–2704, 2017     

Synthesis and characteristics of a novel aliphatic polycarbonate,poly[(propylene oxide)‐co‐(carbon dioxide)‐co‐(γ‐butyrolactone)]

A novel aliphatic polycarbonate, poly[(propylene oxide)‐co‐(carbon dioxide)‐co‐(γ‐butyrolactone)] [P(PO? CO₂? GBL)], was synthesized by the copolymerization of carbon dioxide, propylene oxide (PO) and γ‐butyrolactone (GBL). The resulting copolymers were determined by FTIR and NMR spectral analysis with viscosity‐average molecular weights (M_v) from 50 000 to 120 000 g mol^?1. According to elemental analysis, the calculated data of elemental contents in P(PO? CO₂? GBL)44 were close to the found data. The result showed that GBL was inserted into the backbone of poly[(propylene oxide)‐co‐(carbon dioxide)] successfully. GBL offered an ester structural unit that gave the copolymer better degradability. The correlations between reaction conditions and properties were studied. When GBL content increased, the M_v and the glass transition temperature (T_g) of the copolymers improved relative to an identical copolymer without GBL. Prolonging the reaction time of the copolymerization resulted in increases in M_v and T_g. P(PO? CO₂? GBL) exhibited a high T_g above 40 °C. The rate of backbone degradation increased with increasing GBL content. Copyright © 2005 Society of Chemical Industry     

A new model for correlation and prediction of equilibrium CO2 solubility in N‐methyl‐4‐piperidinol solvent

In this work, the equilibrium CO₂ solubility in the aqueous tertiary amine, N‐methyl‐4‐piperidinol (MPDL) was measured over a range of temperatures, CO₂ partial pressures and amine concentrations. The dissociation constant of the MPDL solution was determined as well. A new thermodynamic model was developed to predict the equilibrium CO₂ solubility in the MPDL‐H₂O‐CO₂ system. This model, equipped with the correction factor (C_f), can give reasonable prediction with an average absolute deviation of 2.0%, and performs better than other models (i.e., KE model, Li‐Shen model, and Hu‐Chakma). The second‐order reaction rate constant (k₂) of MPDL and the heat of CO₂ absorption (–ΔH_abs) into aqueous MPDL solutions were evaluated as well. Based on the comparison with some conventional amines, MPDL revealed a high‐equilibrium CO₂ loading, reasonably fast absorption rate when compared with other tertiary amines, and a low energy requirement for regeneration. It may, therefore, be considered to be an alternative solvent for CO₂ capture. © 2017 American Institute of Chemical Engineers AIChE J, 63: 3395–3403, 2017     

An experimental/computational study of steric hindrance effects on CO2 absorption in (non)aqueous amine solutions

The reaction kinetics and molecular mechanisms of CO₂ absorption using nonaqueous and aqueous monoethanolamine (MEA)/methyldiethanolamine (MDEA)/2-amino-2-methy-1-propanol (AMP) solutions were analyzed by the stopped-flow technique and ab initio molecular dynamics (AIMD) simulations. Pseudo first-order rate constants (k₀) of reactions between CO₂ and amines were measured. A kinetic model was proposed to correlate the k₀ to the amine concentration, and was proved to perform well for predicting the relationship between k₀ and the amine concentration. The experimental results showed that AMP/MDEA only took part in the deprotonation of MEA-zwitterion in nonaqueous MEA + AMP/MEA + MDEA solutions. In aqueous solutions, AMP can also react with CO₂ through base-catalyzed hydration mechanism beside the zwitterion mechanism. Molecular mechanisms of CO₂ absorption were also explored by AIMD simulations coupled with metadynamics sampling. The predicted free-energy barriers of key elementary reactions verified the kinetic model and demonstrated the different molecular mechanisms for the reaction between CO₂ and AMP.     

An experimental investigation on the influence of phenol on the solubility of CO2 in aqueous solutions of NaOH

Experimental results are presented for the solubility of CO₂ in an aqueous solution of phenol and NaOH (molalties in water: phenol: 0.5; NaOH: 1.0) at (314, 354, and 395) K and pressures up to 10 MPa. The experimental work extends recent investigations on the influence of phenol as well as of (phenol + NaCl) on the solubility of CO₂ in water. In contrast to those previous investigations, the strong electrolyte reacts with carbon dioxide and also with phenol. The experimental results are compared with predictions from a thermodynamic model. That model combines a model for the “chemical” solubility of CO₂ in aqueous solutions of NaOH with a model for the “physical” solubility of CO₂ in aqueous solutions of phenol. An extension is introduced to account for the chemical reaction between the weak acid phenol and the strong base sodium hydroxide. The prediction results nicely agree with the new experimental data. © 2015 American Institute of Chemical Engineers AIChE J, 61: 2832–2840, 2015     

The absorption rate of CO2/SO2/NO2 into a blended aqueous AMP/ammonia solution

The Inter-governmental Panel on Climate Change (IPCC) reported that human activities result in the production of greenhouse gases (CO₂, CH₄, N₂O and CFCs), which significantly contribute to global warming, one of the most serious environmental problems. Under these circumstances, most nations have shown a willingness to suffer economic burdens by signing the Kyoto Protocol, which took effect from February 2005. Therefore, an innovative technology for the simultaneously removal carbon dioxide (CO₂) and nitrogen dioxide (NO₂), which are discharged in great quantities from fossil fuel-fired power plants and incineration facilities, must be developed to reduce these economical burdens. In this study, a blend of AMP and NH₃ was used to achieve high absorption rates for CO₂, as suggested in several publications. The absorption rates of CO₂, SO₂ and NO₂ into aqueous AMP and blended AMP+NH₃ solutions were measured using a stirred-cell reactor at 293, 303 and 313 K. The reaction rate constants were determined from the measured absorption rates. The effect of adding NH₃ to enhance the absorption characteristics of AMP was also studied. The performance of the reactions was evaluated under various operating conditions. From the results, the reactions with SO₂ and NO₂ into aqueous AMP and AMP+NH₃ solutions were classified as instantaneous reactions. The absorption rates increased with increasing reaction temperature and NH₃ concentration. The reaction rates of 1, 3 and 5 wt% NH₃ blended with 30 wt% AMP solution with respect to CO₂/SO₂/NO₂ at 313 K were 6.05～8.49×10^?6, 7.16–10.41×10^?6 and 8.02～12.0×10^?6 kmol m^?2s^?1, respectively. These values were approximately 32.3–38.7% higher than with aqueous AMP solution alone. The rate of the simultaneous absorption of CO₂/SO₂/NO₂ into aqueous AMP+NH₃ solution was 3.83–4.87×10^?6 kmol m^?2s^?1 at 15 kPa, which was an increase of 15.0–16.9% compared to 30 wt% AMP solution alone. This may have been caused by the NH₃ solution acting as an alternative for CO₂/SO₂/NO₂ controls from flue gas due to its high absorption capacity and fast absorption rate.     

Activation of lipase by sol–gel coating with hydrophobic alkyl‐substituted silicates in supercritical carbon dioxide

BACKGROUND: Sol–gel entrapment of lipases is usually performed in an aqueous solution. A novel method of sol–gel coating of lipase in supercritical carbon dioxide (SC‐CO₂) is proposed. RESULTS: Crude lipase powder (Rhizopus oryzae) coated with hydrophobic silicates, derived from dimethyldimethoxysilane and tetramethoxysilane in SC‐CO₂ at 35 °C and 15 MPa, exhibited 5–7 times higher esterification activity than that prepared via an aqueous sol–gel route. Lipase immobilized in a methyl‐substituted silica monolith was also highly activated by sol–gel coating using the same silica precursors in SC‐CO₂. CONCLUSION: Sol– gel coating in SC‐CO₂, of lipases in powder and immobilized forms with hydrophobic alkyl‐substituted silicates provides an efficient tool for the enhancement of enzymatic activities in non‐aqueous media. Copyright © 2009 Society of Chemical Industry     

Investigation on kinetics of carbon dioxide absorption in aqueous solutions of monoethanolamine + 1, 3-diaminopropane

ABSTRACT

Environmental concerns from global warming and climate change demand carbon dioxide separation from post-combustion gases. Important parameters are involved in choosing the suitable solvent for carbon dioxide separation, including the reaction rate of carbon dioxide and the solvent. In this paper, the kinetics of carbon dioxide (CO₂) absorption in aqueous solutions of Monoethanolamine (MEA) + 1,3-Diaminopropane (DAP), a diamine containing two primary amino group, was developed. The measurements were performed in a stirred cell with a horizontal gas-liquid interface in the temperature range of 313.15–333.15 K and aqueous solutions of 10 wt% MEA + 5 wt% DAP and 12.5 wt% MEA + 2.5 wt% DAP. Experiments were conducted in an isothermal batch reactor with a horizontal gas-liquid interface under pseudo-first-order conditions, enabling the determination of the overall kinetic rate constant from the pressure drop method. Second-order reaction rate constants of CO₂ absorption in amine solutions were estimated using the calculated initial absorption rate. It was found that the rate constants in MEA+ DAP solutions were greater than in MEA solutions which means that DAP increases the reaction rate.     

Liquid‐liquid phase split in ionic liquid + toluene mixtures induced by CO2

High pressure carbon dioxide was dissolved in ionic liquid + toluene mixtures to obtain the conditions of pressure and composition where a liquid‐liquid phase split occurs at constant temperature. Ionic liquids (ILs) with four different cations paired with the bis(trifluoromethylsulfonyl)imide ([Tf₂N]^?) anion were selected: 1‐hexyl‐3‐methylimidazolium ([hmim]⁺), 1‐hexyl‐3‐methylpyridinium ([hmpy]⁺), triethyloctylphosphonium ([P₂₂₂₈]⁺), and tetradecyltrihexylphosphonium ([P₆₆₆₁₄]⁺). The solubility of CO₂ was measured in the liquid mixtures at temperatures between 298 and 333 K and at pressures up to 8 MPa, or until the second liquid phase appeared, for initial liquid phase compositions of 0.30, 0.50, and 0.70 mole fraction of IL. Ternary isotherms were compared with the binary solubility of CO₂ in each IL and pure toluene. The lowest pressure for separating toluene in a second liquid phase was achieved by decreasing the temperature of the system, increasing the amount of toluene in the initial liquid mixture and using [hmim][Tf₂N]. © 2015 American Institute of Chemical Engineers AIChE J, 61: 2968–2976, 2015     

Reaction Mechanism and Kinetics of 1,8‐Diazabicyclo[5.4.0]undec‐7‐ene and Carbon Dioxide in Alkanol Solutions

Carbon dioxide‐binding organic liquids (CO₂BOL) are a new class of solvents with advantageous properties such as high boiling points, low specific heats, high absorption capacities, and easily reversible reactions. In order to implement these solvents in processes, the reaction characteristics must be determined a priori. This work presents an analysis of the rate constants and activation energies of the reaction between carbon dioxide and 1,8‐diazabicyclo[5.4.0]undec‐7‐ene (DBU) in 1‐hexanol and 1‐propanol. The reactions were found to comply with a termolecular reaction mechanism and exhibited pseudo‐first‐order behavior in the presence of excess DBU and 1‐alkanol. It was concluded that DBU‐based CO₂BOL are environmentally friendly and easy‐to‐handle solvents that may provide great flexibility and improvements over conventional carbon dioxide absorption processes.     

Mass‐transfer rate enhancement for CO2 separation by ionic liquids: Theoretical study on the mechanism

To promote the development of ionic liquid (IL) immobilized sorbents and supported IL membranes (SILMs) for CO₂ separation, the kinetics of CO₂ absorption/desorption in IL immobilized sorbents was studied using a novel method based on nonequilibrium thermodynamics. It shows that the apparent chemical‐potential‐based mass‐transfer coefficients of CO₂ were in three regions with three‐order difference in magnitude for the IL‐film thicknesses in microscale, 100 nm‐scale, and 10 nm‐scale. Using a diffusion‐reaction theory, it is found that by tailoring the IL‐film thickness from microscale to nanoscale, the process was altered from diffusion‐control to reaction‐control, revealing the inherent mechanism for the dramatic rate enhancement. The extension to SILMs shows that the significant improvement of CO₂ flux can be obtained theoretically for the membranes with nanoscale IL‐films, which makes it feasible to implement CO₂ separation by ILs with low investment cost. © 2015 American Institute of Chemical Engineers AIChE J, 61: 4437–4444, 2015     

Modeling of CO2 equilibrium solubility in a novel 1‐Diethylamino‐2‐Propanol Solvent

In this work, the equilibrium solubility of CO₂ in a 1‐diethylamino‐2‐propanol (1DEA2P) solution was determined as a function of 1DEA2P concentration (over the range of 1–2 M), temperature (in the range of 298–333 K), and CO₂ partial pressure (in the range of 8–101 kPa). These experimental results were used to fit the present correlation for K₂ (Kent‐Eisenberg model, Austgen model, and Li‐Shen model). It was found that all of the models could represent the CO₂ equilibrium solubility in 1DEA2P solution with ADDs for Kent‐Eisenberg model, Austgen model, and Li‐Shen model of 6.3, 7.3, and 12.2%, respectively. A new K₂ correlation model, the Liu‐Helei model, was also developed to predict the CO₂ equilibrium solubility in 1DEA2P solution with an excellent ADD of 3.4%. In addition, the heat of absorption of CO₂ in 1DEA2P solution estimated by using the Gibbs‐Helmholtz equation was found to be ?45.7 ± 3.7 kJ/mol. Information and guidelines about effectively using data for screened solvents is also provided based on the three absorption parameters: CO₂ equilibrium solubility, second order reaction constant (k₂), and CO₂ absorption heat. © 2017 American Institute of Chemical Engineers AIChE J, 63: 4465–4475, 2017