The effect of system pressure on gas‐liquid slug flow in a microchannel

Characteristics of gas‐liquid two‐phase flow under elevated pressures up to 3.0 MPa in a microchannel are investigated to provide the guidance for microreactor designs relevant to industrial application. The results indicate that a strong leakage flow through the channel corners occurs although the gas bubbles block the channel. With a simplified estimation, the leakage flow is shown to increase with an increase in pressure, leading to a bubble formation shifting from transition regime to squeezing regime. During the formation process, the two‐phase dynamic interaction at the T‐junction entrance would have a significant influence on the flow in the main channel as the moving velocity of generated bubbles varies periodically with the formation cycle. Other characteristics such as bubble formation frequency, bubble and slug lengths, bubble velocities, gas hold‐up, and the specific surface area are also discussed under different system pressures. © 2013 American Institute of Chemical Engineers AIChE J, 60: 1132–1142, 2014     

Formation of liquid–liquid slug flow in a microfluidic T‐junction: Effects of fluid properties and leakage flow

Characteristics of liquid–liquid slug flow are investigated in a microchannel with focus on the leakage flow that bypasses droplets through channel gutters. The results show that the leakage flow rate varies in a range of 10.7–53.5% and 8.3–30.9% of the feed flow rate, during the droplet formation (i.e., at T‐junction) and downstream flow (i.e., in the main channel), respectively, which highly depends on Ca number and wetting condition. Empirical correlations are proposed to predict them for perfectly and partially wetting conditions. Leakage flow contribution is further used to improve the Garstecki model for size scaling in order to extend its suitability for both squeezing and shearing regimes. The instantaneous flow rates of the immiscible phases are found to fluctuate periodically with the formation cycles, but in opposite behavior. The effect of the presence of leakage flow on such fluctuation are investigated and compared with gas–liquid systems. © 2017 American Institute of Chemical Engineers AIChE J, 63: 346–357, 2018     

Bubble/droplet formation and mass transfer during gas–liquid–liquid segmented flow with soluble gas in a microchannel

Microchannels have great potential in intensification of gas–liquid–liquid reactions involving reacting gases, such as hydrogenation. This work uses CO₂–octane–water system to model the hydrodynamics and mass transfer of such systems in a microchannel with double T‐junctions. Segmented flows are generated with three inlet sequences and the size laws of dispersed phases are obtained. Three generation mechanisms of dispersed gas bubbles/water droplets are identified: squeezing by the oil phase, cutting by the droplet/bubble, cutting by the water–oil/gas–oil interface. Based on the gas dissolution rate, the mass transfer coefficients are calculated. It is found that water droplet can significantly enhance the transfer of CO₂ into the oil phase initially. When bubble‐droplet cluster are formed downstream the microchannel, droplet will retard the mass transfer. Other characteristics such as phase hold‐up, bubble velocity and bubble dissolution rate are also discussed. The information is beneficial for microreactor design when applying three‐phase reactions. © 2016 American Institute of Chemical Engineers AIChE J, 63: 1727–1739, 2017     

The effect of liquid viscosity and modeling of mass transfer in gas–liquid slug flow in a rectangular microchannel

Both chemical (by adding 0.05 M NaOH) and physical absorption of CO₂ into aqueous glycerol solutions with viscosity up to 45.6 mPa·s in a microchannel are investigated. The concentration distribution pattern, absorption time, and mass transfer coefficient are analyzed and discussed. A new concentration distribution pattern is observed with the lowest concentration locating at the channel center. It is shown for the first time that presents a positive relationship with liquid viscosity, which is explained by the essential role of the mass exchange between the liquid film and bulk liquid slug. This mass exchange may lead to a rise in k _L when increasing the liquid viscosity under some cases in chemical absorption. A mass transfer model is successfully applied to predict the bubble size evolution in physical absorption. The model also shows about 10–46% of the mass transfer contribution from liquid films before saturation.     

微通道内气-液弹状流动及传质特性研究进展

气-液弹状流,又称Taylor流,是一种以长气泡和液弹交替形式流动的流动形态。微通道内气-液弹状流因其气泡与液弹尺寸分布均一、停留时间分布窄、径向混合强等优点,是一种适于强化气-液反应的理想流型。本文首先介绍了微通道内气泡的生成机理、气泡和液弹长度,以及气泡生成阶段的传质特征。其次系统综述了主通道中弹状流动及传质过程的研究进展,包括气泡形状与液膜厚度、液弹内循环和泄漏流特征、气-液传质系数的测量与预测,以及物理与化学吸收过程中的传质特性等方面内容。最后阐述了当前研究的不足并展望了气-液弹状流的研究方向。     

Influence of hydrodynamics on liquid mixing during Taylor flow in a microchannel

The miscible liquid‐liquid two phases based on Taylor flow in microchannels was investigated by high‐speed imaging techniques and Villermaux/Dushman reaction. The mixing based on Taylor flow was much better compared with that without introducing gas in microchannels, even the ideal micromixing performance could be obtained under optimized superficial gas and liquid velocities. In the mixing process based on Taylor flow, the superficial gas and liquid velocities affected the lengths and the velocities of Taylor bubble and liquid slug, and finally the micromixing performance. The formation process of Taylor flow in the inlets, the initial uniform distribution of reactants and the internal circulations in the liquid slug, and the thin liquid films all improved the mixing performance. Furthermore, a modified Peclet number that represented the relative importance of diffusion and convection in the mixing process was proposed for explaining and anticipating micromixing efficiency. © 2011 American Institute of Chemical Engineers AIChE J, 58: 1660–1670, 2012     

Bubble splitting under gas–liquid–liquid three‐phase flow in a double T‐junction microchannel

Gas–aqueous liquid–oil three‐phase flow was generated in a microchannel with a double T‐junction. Under the squeezing of the dispersed aqueous phase at the second T‐junction (T2), the splitting of bubbles generated from the first T‐junction (T1) was investigated. During the bubble splitting process, the upstream gas–oil two‐phase flow and the aqueous phase flow at T2 fluctuate in opposite phases, resulting in either independent or synchronous relationship between the instantaneous downstream and upstream bubble velocities depending on the operating conditions. Compared with two‐phase flow, the modified capillary number and the ratio of the upstream velocity to the aqueous phase velocity were introduced to predict the bubble breakup time. The critical bubble breakup length and size laws of daughter bubbles/slugs were thereby proposed. These results provide an important guideline for designing microchannel structures for a precise manipulation of gas–liquid–liquid three‐phase flow which finds potential applications among others in chemical synthesis. © 2017 American Institute of Chemical Engineers AIChE J, 63: 376–388, 2018     

Liquid flow pattern around Taylor bubbles in an etched rectangular microchannel

Liquid flow around Taylor bubbles and the motion of bubble interface in a rectangular microchannel etched on a microfluidic chip were investigated using a three-dimensional particle tracking method. The Taylor bubbles were generated by releasing the dissolved air in working the liquid (water) through heating the microfluidic chip to 35–55 °C and had low velocities (15–1500 μm/s). Three-dimensional velocity distributions of liquid recirculation flows surrounding the Taylor bubble head and tail were obtained by tracking submicron fluorescent particles seeded in the working liquid and the motion of the bubble interface was analyzed by monitoring the motions of the particles attached on the bubble interface. The high velocity film flow through the microchannel corners acted as a liquid jet in front of bubble head and drainage into the corners behind the bubble tail to drive the liquid recirculation flows. The bubble interface near the microchannel corners was also moved by the strong liquid shear induced from the high velocity liquid flow in the microchannel corners. This high velocity liquid flow through the corners could be considered to be driven by the pressure drop over the Taylor bubble. The pressure drop resulted from the decrease of bubble surface mobility due to tracer surfactant in the gas–liquid interface.     

Droplet breakup in the square microchannel with a short square constriction to generate slug flow

Droplet breakup in microconstrictions is an important phenomenon in industrial applications. This work aimed to investigate the droplet breakup in the square microchannel with a short square constriction to generate the slug flow, which drew little attention before. Mechanism analysis indicated that this breakup process included the shear-force-dominated, squeezing-force-dominated, and pinch-off stages. Nonuniform daughter droplets were generated in the constriction with their interface restricted in the horizontal and perpendicular directions by the microchannel walls. The average relative deviation of the daughter droplet size was <30%, much lower than that for the breakup with the daughter droplet restricted only in one direction. An empirical equation with a deviation of <20% was provided to show the dependence of the daughter droplet size on the operation conditions. The comparison results suggested that the different restriction effects of microchannel wall on daughter droplets led to the different breakup mechanisms in different constrictions.     

蛇形微通道内泄漏流特性

微流体系统通常具备极大的比表面积、易于控制等优势,在气-液相传质、传热、反应等方面具有良好的应用前景。本文考察了6个气液相体系在矩形截面蛇形微通道中的气液两相泰勒流流动情况以及气泡和液弹的动态行为,以气泡截面形状的几何模型为基础,得到了微通道中净泄漏流的量化方程。同时发现在较大的操作区间内,蛇形微通道对泄漏流的可控性优于直形微通道。并且详细分析了不同气液相流量、液相物性（表面张力和黏度）和气泡长度对蛇形微通道主通道净泄漏流的具体影响。     

The effect of gas diffusion layer compression on gas bypass and water slug motion in parallel gas flow channels

Water slugs form in the gas flow channels of polymer electrolyte membrane fuel cells (PEMFCs) which hinder reactant transport to the catalyst layer. We report a study correlating video images of slug formation and motion with pressure/flow measurements in parallel gas flow channels. Slugs move when the differential gas pressure exceeds the force to advance the contact lines of the slug with the channel walls. Water slugs can divert the gas flow through the gas diffusion layer (GDL) beneath the ribs to adjacent channels. The flow diversion can cause slugs to stop moving. Slug size and motion has been correlated with in situ GDL permeabilities as functions of GDL compression. Compression reduces the GDL permeability under the ribs much more than the GDL permeability under the channel. A model is presented to describe the spatio‐temporal location of slugs in a PEMFC flow field. © 2014 American Institute of Chemical Engineers AIChE J, 61: 355–367, 2015     

水平管油气两相段塞流及其传热特性

海底油气管道的冷却传热过程是结蜡、水合物等海洋石油工业流动保障问题的关键控制因素。采用电容探针与热电偶、热电阻等流动及温度测量手段对不同冷却条件下空气-油段塞流的流动参数和传热参数进行实验测量,分析了空气-油段塞流流动参数对传热特性的影响,并与空气-水对流换热进行对比。结果表明,空气-油段塞流对流传热系数主要受液相折算速度的影响,且冷却液温度越低,管底热流体黏度越大,导致热边界层越厚,传热系数降低;受黏性力及边界层影响,对流传热系数远小于空气-水;沿管壁周向,从管顶到管底的对流传热系数不断增大。提出了适用于冷却条件下的油气段塞流传热关联式和传热模型。     

十字聚焦型微通道内弹状液滴在黏弹性流体中的生成与尺寸预测

利用高速摄像仪对十字聚焦微通道内液滴在黏弹性流体中的生成过程进行了实验研究。微通道截面为600μm×600 μm 的正方形结构,采用硅油作为分散相,含0.3%表面活性剂十二烷基硫酸钠(SDS)的聚环氧乙烷(PEO)水溶液(质量分数分别为0.1%,0.3%,0.6%)为连续相。实验观察到了弹状流、滴状流和喷射流3 种流型。对弹状流型下液滴生成过程的颈部动力学进行了研究,考察了两相流率、连续相毛细数及弹性数对液滴尺寸的影响。结果表明:弹状液滴尺寸随连续相流率、毛细数及弹性数的增加而减小,随分散相流率的增加而增加,连续相弹性对液滴尺寸的影响相对较小。以油水两相流率比和连续相的毛细数及Reynolds 数为变量建立了弹状液滴尺寸的预测关联式,预测值与实验值吻合良好。     

微通道壁面浸润性对气-液两相流的影响规律研究

通道壁面浸润性对微通道内的气-液两相流具有重要影响。利用等离子体辅助接枝改性,将甲基丙烯酰乙基磺基甜菜碱（SBMA）及1H, 1H, 2H, 2H-全氟癸基三乙氧基硅烷接枝在聚甲基丙烯酸甲酯（PMMA）材料表面,得到了10°、40°、70°和110°四种接触角的微通道,并考察了浸润性对流型、气泡长度和压降的影响。结果表明,随接触角增大,气泡截断位置下移,膨胀阶段缩短,挤压阶段变长;低流量时,气泡长度随接触角增加而增大,高流量时则减小;建立了与材料表面水接触角相关的气泡尺寸预测关联式,与Garstecki经典预测关联式相比,预测精度更高;θ<90°时,接触角增加,压降减小;θ>90°时,三相接触线使流动阻力和压降增加。     

水平管气液两相段塞流的波动特性

气液两相段塞流是液塞和长气泡在空间和时间上的交替,在流动过程中表现出间歇性和不稳定性。系统地研究了水平管中段塞流持液率、压力和压差的波动特性。结果表明,段塞流持液率的概率密度分布为双峰分布,高持液率峰对应于液塞区,低持液率峰对应于液膜区;在压力的概率密度分布中,当压力测试点到管道出口之间的段塞单元数目少时,压力分布出现双峰分布;当压力测试点到管道出口之间的段塞单元数目多时,压力分布出现单峰分布;压差信号分布呈单峰分布。这些特征为流型识别提供了可靠的段塞流标识。     

Aerobic oxidation of benzyl alcohol in a slug flow microreactor: Influence of liquid film wetting on mass transfer

Homogeneous Co/Mn/Br catalyzed aerobic oxidation of benzyl alcohol in acetic acid to benzaldehyde was performed in polytetrafluoroethylene microreactors operated under slug flow at temperatures up to 150°C and pressures up to 5 bar. Depending on the bubble velocity and length, a wetted or dewetted slug flow was observed, characterized typically by a complete or partially wetting liquid film around the bubble body. The latter flow suffered from a limited interfacial area for mass transfer. Experiments at temperatures up to ca. 90°C were under kinetic control given no product yield difference under wetted and dewetted slug flows and were used to establish a simplified kinetic expression (first order in benzyl alcohol and zero order in oxygen). This allows to develop a mass transfer model combined with an instantaneous reaction regime that well described the experimental results at higher temperatures where mass transfer was limiting in the dewetted slug flow.     

Liquid‐liquid two‐phase flow patterns in a new helical microchannel device

Flow patterns of liquid‐liquid two‐phase fluids in a new helical microchannel device were presented in this paper. Three conventional systems were considered: kerosene‐water, n‐butyl acetate‐water, and butanol‐water. Six different flow patterns, slug flow, continuous parallel flow, discontinuous deformation parallel flow, discontinuous deformation parallel‐droplet flow, droplet‐slug flow, and filiform‐droplet flow, were observed. The influence of interfacial tension, microchannel structure, and rotation rate on two‐phase flow patterns were studied, and a universal flow pattern map was presented and discussed. The systems without mass transfer (0.1 g/g (10 %) tri‐n‐butyl phosphate (TBP)‐water, 0.2 g/g (20 %) TBP‐water, and 0.8 g/g (80 %) TBP‐water) and the system with mass transfer (0.8 g/g (80 %) TBP‐0.62 g/g (62 %) H₃PO₄) were used to verify the validity of the proposed universal flow pattern map in predicting flow patterns. The results showed that the former compared with the latter can be predicted more accurately by the universal flow pattern map.     

Motion of a magnetic flow follower in two‐phase flow — application to the study of airlift reactor hydrodynamics

A low‐cost and simple magnetic particle tracer method was adapted to characterize the hydrodynamic behavior of an internal‐ and an external‐loop airlift reactor (ALR). The residence time distribution of three magnetic particles differing in diameter (5.5, 11.0 and 21.2 mm) and with a density very close to that of water was measured in individual reactor sections. The measured data were analyzed and used to determine the velocity of the liquid phase. Validation of the experimental results for liquid velocity was done by means of the data obtained by an independent reference method. Furthermore, analysis of the differences found in the settling velocity of the particle in single‐liquid and gas‐liquid phases was carried out, using a simplified 3D momentum transfer model. The model considering particle‐bubble interaction forces resulting from changes in the liquid velocity field due to bubble motion was able to predict satisfactorily the increase in the particle settling velocity in the homogeneous bubbly regime. The effective drag coefficient in two‐phase flow was found to be directly dependent on particle Reynolds number to the power of ? 2 but independent of gas flow‐rate for all particle diameters studied. Based on the experimental and theoretical investigations, the valid exact formulation of the effective buoyancy force necessary for the calculation of the correct particle settling velocity in two‐phase flow was done. In addition, recommendations concerning the use of flow‐following particles in internal‐loop ALRs for liquid velocity measurements are presented. Copyright © 2006 Society of Chemical Industry     

Scaling of the bubble/slug length of Taylor flow in a meandering microchannel

In order to reduce or avoid the fluctuations from interface breakup, a meandering microchannel with curved multi-bends (44 turns) is fabricated, and investigations of scaling bubble/slug length in Taylor flow in a rectangular meandering microchannel are systematically conducted. Based on considerable experimental data, quantitative analyses for the influences of two important characteristic times, liquid phase physical properties and aspect ratio are made on the prediction criteria for the bubble/slug length of Taylor flow in a meandering microchannel. A simple principle is suggested to predict the bubble formation period by using the information of Rayleigh time and capillary time for six gas-liquid systems with average deviation of 10.96%. Considering physical properties of the liquid phase and cross-section configuration of the rectangular mcirochannel, revised scaling laws for bubble length are established by introducing Ca, We, Re and W/h whether for the squeezing-driven or shearing-driven of bubble break. In addition, a simple principle in terms of Garstecki-type model and bubble formation period is set-up to predict slug lengths. A total of 107 sets of experimental data are correlated with the meandering microchannel and operating range:0.001 < Ca_TP < 0.05, 0.06 < We_TP < 9.0, 18 < Re_TP < 460 using the bubble/slug length prediction equation from current work. The average deviation between the correlated data and the experimental data for bubble length and slug length is about 9.42% and 9.95%, respectively.