Experimental investigation of electrostatic effect on particle motions in gas‐solid fluidized beds

The excess accumulation of charges in the fluidized bed has a severe impact on hydrodynamics. Due to lack of effective experimental methods, electrostatic effects on hydrodynamics have mostly been studied using numerical simulation. By injecting a trace of liquid antistatic agents into a fluidized bed, charges were controlled and electrostatic influences on particle motions were investigated. The average particle–wall impact angles are acquired by developing multiscale wavelet decomposition of acoustic emission signals. The impact angles are significantly influenced by both charge levels and gas velocities. If the electric force is reduced and/or fluid drag is increased, friction dominates the particle–wall interactions. Under a larger gas velocity where fluid drag dominates, charges elimination causes no significant variation in particle impact angles, but particle velocities increase as well as at lower gas velocities. In addition, existence of electrostatic charges influences the ranges of bubble growing zone and jet impacting zone. © 2015 American Institute of Chemical Engineers AIChE J, 61: 3628–3638, 2015     

Particles mixing induced by bubbles in a gas‐solid fluidized bed

The effect of bubble injection characteristics on the mixing behavior of a gas‐solid fluidized bed is investigated using a discrete particle model. The effect of different parameters including gas injection time, velocity, and mode are studied. Simulation results show that injecting gas at a constant gas flow rate in the form of small bubbles results in a better overall particle mixing. It was also found that the injection velocities have limited effect on particle mixing behavior for the same total gas volume injected into the bed. Moreover, the mixing index (MI) of continuous gas jet bubbling regime is compared with the MI obtained in uniform gas injection regime and the results revealed that the MI of continuous jet bubbling regime has a larger value than that of uniform gas injection regime at the fixed total gas flow rate. In both regimes, z‐direction MI is larger than x‐direction index. The differences between two direction indices are more noticeable in continuous jet bubbling in comparison with the uniform gas injection regime. © 2016 American Institute of Chemical Engineers AIChE J, 62: 1430–1438, 2016     

Numerical investigation of gas mixing in gas‐solid fluidized beds

Gas mixing in a tall narrow fluidized bed operated in the slugging fluidization regime is simulated with the aid of computational fluid dynamics. In the first part, a parametric study is conducted to investigate the influence of various parameters on the gas mixing. Among the parameters studied, the specularity coefficient for the partial‐slip solid‐phase wall boundary condition had the most significant effect on gas mixing. It was found that the solid‐phase wall boundary condition needs to be specified with great care when gas mixing is modeled, with free slip, partial slip and no‐slip wall boundary conditions giving substantial differences in the extent of gas back mixing. Axial and radial tracer concentration profiles for different operating conditions are generally in good agreement with experimental data from the literature. Detailed analyses of tracer back mixing are carried out in the second part. Two parameters, the tracer backflow fraction and overall gas backflow fraction, in addition to axial profiles of cross‐sectional averaged tracer concentrations, are evaluated for different flow conditions. Qualitative trends are consistent with reported experimental findings. © 2010 American Institute of Chemical Engineers AIChE J, 2010     

高密度浓相流化床中气泡的兼并与分裂特性

利用先进的高速动态分析系统对二维床中气泡的行为进行了研究,通过对所拍摄图象的分析处理．得到了不同介质流化床内形成的气泡形状、大小、聚并及分裂的基本规律和特点．实验研究表明．气泡的兼并主要是两气泡问的合并、被合并气泡总是从气泡的尾涡区曳入气泡;气泡分裂主要发生在操作气速较大或大气泡中,是由于其顶部粒子流(或“剪切流”)的侵入造成的;操作气速较低,粒度、密度较大粒子形成的流化床更易于造成气泡的湮灭。     

Transient multi gas—solid reactions in a bubbling fluidized bed

A “multimodel” for gas‐solid reactions in a reacting particle has been applied to a bubbling fluidized bed reactor. The particle is tracked and bed and particle variables are determined continuously. The conservation equations of mass and heat with auxiliary relations are solved in an accelerating particle, which may rise or fall. The effects of bulk pressure, velocity and temperature, and particle diameter are studied. Heat and mass transfer coefficients may fluctuate up to 75% and 148% respectively. Doubling the pressure changes h_c by 75% and k_c by ?45%. Increase in pellet diameter reduces both h_c and k_c.     

Characterization on hydrodynamic behavior in liquid‐containing gas‐solid fluidized bed reactor

In many industrial processes involving gas–solid fluidized bed rectors, the addition of a liquid phase significantly alters the hydrodynamics. To fully characterize the hydrodynamics in the fluidized bed, pressure and acoustic measuring techniques were applied to study the behavior of gas bubbles and particles. A camera was used to take pictures to verify the pressure and acoustic results. During the liquid‐addition process, the pressure technique captured the bubble size variation and bubble motion while the acoustic technique reflected particle motion and particle size growth. Hurst and V‐statistics analyses of acoustic emission were used for the first time to detect periodic behavior during the injection process. The new break formation and change trend of V_max were used as the criteria to judge occurrence of abnormal fluidization states, such as agglomeration and gas channeling formation. These measurement techniques are beneficial in the elimination of adverse effects caused by the addition of liquid. © 2012 American Institute of Chemical Engineers AIChE J, 59: 1056–1065, 2013     

Experimental and numerical research for fluidization behaviors in a gas–solid acoustic fluidized bed

The effects of sound assistance on fluidization behaviors were systematically investigated in a gas–solid acoustic fluidized bed. A model modified from Syamlal–O'Brien drag model was established. The original solid momentum equation was developed and an acoustic model was also proposed. The radial particle volume fraction, axial root‐mean‐square of bed pressure drop, granular temperature, and particle velocity in gas–solid acoustic fluidized bed were simulated using computational fluid dynamics (CFD) code Fluent 6.2. The results showed that radial particle volume fraction increased using modified drag model compared with that using the original one. Radial particle volume fraction was revealed as a parabolic concentration profile. Axial particle volume fraction decreased with the increasing bed height. The granular temperature increased with increasing sound pressure level. It showed that simulation values using CFD code Fluent 6.2 were in agreement with the experimental data. © 2009 American Institute of Chemical Engineers AIChE J, 2010     

Borescopy in pressurized gas‐solid fluidized beds

A borescopic technique was used for finding the effect of pressure on the hydrodynamics of gas‐solid fluidized beds. The results showed that solids radial distribution may become more or less uniform with increasing pressure depending on the superficial gas velocity. Moreover, it is found that the solids volume fraction of the emulsion phase may decrease at relatively high pressures, only in the central region of the bed. Additionally, it is observed that with increasing pressure the bubble size generally decreased in the central regions and increased near the wall regions. This trend was more complicated at low excess gas velocities. The number of bubbles increased for the central regions and near the walls for all the performed experiments. However, this parameter showed a different trend at other radial positions. © 2018 The Authors AIChE Journal published by Wiley Periodicals, Inc. on behalf of American Institute of Chemical Engineers AIChE J, 64: 3303–3311, 2018     

Effect of bed size on hydrodynamics in 3‐D gas–solid fluidized beds

It is well known that hydrodynamics observed in large scale gas–solid fluidized beds are different from those observed in smaller scale beds. In this article, an efficient two‐fluid model based on kinetic theory of granular flow is applied, with the goal to highlight and investigate hydrodynamics differences between three‐dimensional fluidized beds of diameter 0.10, 0.15, 0.30, 0.60, and 1.0 m, focusing on the bubble and solids flow characteristics in the bubbling regime. Results for the 0.30 m diameter bed are compared with experimental results from the literature. The bubble size evolution closely follows a correlation proposed by Werther for small beds, and a correlation proposed by Darton for sufficiently large beds. The bubble size increases as the bed diameter is increased from 0.10 to 0.30 m, and remains approximately constant for bed diameters from 0.30 to 1.0 m. Concurrently, an increase in bubble rise velocity is observed, with a much high bubble rise velocity in the largest bed of diameter 1.0 m due to gulf stream circulations. The dynamics in shallow and deep beds is predicted to be different, with marked differences in bubble size and solids circulation patterns. © 2015 American Institute of Chemical Engineers AIChE J, 61: 1492–1506, 2015     

Particle entrainment from gas‐solid fluidized beds: Conductive vs. dielectric fines

Conductive and non‐conductive fine powders were entrained by air at atmospheric temperature and pressure in a fluidization column of diameter 0.15 m made of stainless steel. Under equivalent operating conditions, entrainment of the conductive particles was markedly higher than for non‐conductive species. This finding cannot be explained by hydrodynamic factors. Examining the electrostatic interaction between touching particles reveals that dominance of the inter‐particle attractive forces hinders independent motion of non‐conductive particles in the freeboard. In addition, because of non‐uniform distribution of the electrical charges over the surface of dielectric particles, they are subject to stronger electrostatic forces than for particles made of conductive materials. © 2016 American Institute of Chemical Engineers AIChE J, 63: 1194–1202, 2017     

Realization and control of multiple temperature zones in liquid‐containing gas–solid fluidized bed reactor

Fluidized bed reactors (FBRs) have been developed to establish multiple temperature zones for various industrial processes. To overcome the common weakness, this work proposed to spray liquid into bottom and upper zones, respectively, to realize multiple temperature zones FBR (MTZFBR). Temperature, pressure, and acoustic emission techniques were applied to fully characterize liquid interaction and hydrodynamics. Compared with the bottom liquid‐spraying approach, the upper liquid‐spraying approach showed higher temperature difference (ΔT) and better fluidization stability, thus was selected for further control studies. Effects of liquid flow rate, static bed height, and inlet gas temperature on MTZFBR were studied systematically. The results showed that increasing liquid evaporation behavior or decreasing liquid bridge behavior enhance ΔT and fluidization stability and vice versa. G–L–S fluidization pattern depended mostly on the liquid behaviors and fluidization stability, and thus the stabilized MTZFBR could be regarded as a coexisted mode of two distinctive G–L–S fluidization patterns. © 2016 American Institute of Chemical Engineers AIChE J, 62: 1454–1466, 2016     

On the accuracy of Landweber and Tikhonov reconstruction techniques in gas‐solid fluidized bed applications

As electrical capacitance tomography technique needs a sophisticated reconstruction, the accuracy of two of the most widely used reconstruction techniques (Landweber and Tikhonov) for gas‐fluidized bed applications were assessed. For this purpose, the results of two‐fluid model simulations were used as an input of reconstruction. After finding the optimum reconstruction parameters for the studied system, it is found that both techniques were able to obtain the radial profile and overall value of average volume fraction very well. Conversely, both methods were incapable to determine bubble sizes accurately especially small bubble sizes, unless the Landweber technique with inverted Maxwell concentration model is applied. The probability distribution of the reconstructed results was also smoother in transition between the emulsion and bubble phases compared to the reality. Finally, no significant differences in noise immunity of these two techniques were observed. © 2015 American Institute of Chemical Engineers AIChE J, 61: 4102–4113, 2015     

Two-area model for bubble distribution in a turbulent fluidized bed of fine particles

The flow behavior of gas and solid was investigated in FCC simulator of φ710×4000/φ870×11000mm.The axial and radial distributions were detected with matrix fiber-opticprobes.It was found that the distribution of bubble diameter in the turbulent region of the fluidizedbed of fine particles was different from the results reported for lab-scale experiments.Radially therewere three areas,i.e.,the central(r/R=0-0.4),the intermittent or stable(r/R=0.4-0.8)and thenear wall(r/R=0.8-1.0)areas respectively.It was noticed that bubbles were almost non-existing atthe near wall area.Hence,according to the coalescence and splitting theory of bubbles,a two-areamodel of bubble diameter distribution was proposed and a dimensionless parameter(γ_M)regarded asan index for'quality'of fluidization was deduced.     

Heat transfer between an isolated bubble and the dense phase in a fluidized bed

Heat transfer between the bubble and dense phases of a bubbling fluidized bed plays a very important role in the system performance, especially for applications involving solids drying and gas‐phase combustion. However, very few experimental data are available on this subject in the literature. An experimental and modelling investigation on the heat transfer behaviour of isolated bubbles injected into an incipiently fluidized bed is reported in this paper. A new single‐thermocouple technique was developed to measure the heat transfer coefficient. The effects of bed particle type and size, and bubble size on the heat transfer coefficient were examined. The heat transfer coefficient was found to exhibit a maximum as the bubble size increased in the bubble size range investigated. The bed particle size had a comparatively small effect on the heat transfer coefficient. A simple mathematical model was developed which provides good agreement with experimental data.     

Novel phenomenological discrete bubble model of freely bubbling dense gas–solid fluidized beds: Application to two‐dimensional beds

A phenomenological discrete bubble model has been developed for freely bubbling dense gas–solid fluidized beds and validated for a pseudo‐two‐dimensional fluidized bed. In this model, bubbles are treated as distinct elements and their trajectories are tracked by integrating Newton's equation of motion. The effect of bubble–bubble interactions was taken into account via a modification of the bubble velocity. The emulsion phase velocity was obtained as a superposition of the motion induced by individual bubbles, taking into account bubble–bubble interaction. This novel model predicts the bubble size evolution and the pattern of emulsion phase circulation satisfactorily. Moreover, the effects of the superficial gas velocity, bubble–bubble interactions, initial bubble diameter, and the bed aspect ratio have been carefully investigated. The simulation results indicate that bubble–bubble interactions have profound influence on both the bubble and emulsion phase characteristics. Furthermore, this novel model may become a valuable tool in the design and optimization of fluidized‐bed reactors. © 2012 American Institute of Chemical Engineers AIChE J, 2012     

Experimental and computational study of the bed dynamics of semi‐cylindrical gas–solid fluidized bed

With computational fluid dynamics (CFD) it is possible to get a detailed view of the flow behaviour of the fluidized beds. A profound and fundamental understanding of bed dynamics such as bed pressure drop, bed expansion ratio, bed fluctuation ratio, and minimum fluidization velocity of homogeneous binary mixtures has been made in a semi‐cylindrical fluidized column for gas–solid systems, resulting in a predictive model for fluidized beds. In the present work attempt has been made to study the effect of different system parameters (viz., size and density of the bed materials and initial static bed height) on the bed dynamics. The correlations for the bed expansion and bed fluctuations have been developed on the basis of dimensional analysis using these system parameters. Computational study has also been carried out using a commercial CFD package Fluent (Fluent, Inc.). A multifluid Eulerian model incorporating the kinetic theory for solid particles was applied in order to simulate the gas–solid flow. CFD simulated bed pressure drop has been compared with the experimental bed pressure drops under different conditions for which the results show good agreements.