Ab initio study of electronic structures and absorption properties of pure and Fedoped anatase TiO2

Using the first-principles calculations, the band structure, total and partial density of states (DOS) and absorption properties of anatase TiO₂, Fe³⁺ doped TiO₂ and FeTiO₃ were calculated by a plane-wave pseudopotential method based on density functional theory (DFT). From the calculated results, the band gaps of anatase TiO₂, Fe³⁺ doped TiO₂ and FeTiO₃ are about 2.4, 0.32 and 0.28 eV, respectively. The states of the valence bands and conduction bands of undoped and Fe³⁺ doped TiO₂ with anatase structure were calculated. As shown in the absorption spectra, the FeTiO₃ has the strongest absorption and the Fe-TiO₂ has the weakest absorption. Effect of Fe³⁺ dopant on the absorption property of the anatase TiO₂ is explained in detail based on the calculations using the first-principles. The Fe³⁺ doped anatase TiO₂ could be a potential candidate for photocatalyst because of the absorption ability of visible light.     

Enhanced bio-hydrogen production from sugarcane juice by immobilized Clostridium butyricum on sugarcane bagasse

Immobilized Clostridium butyricum TISTR 1032 on sugarcane bagasse improved hydrogen production rate (HPR) approximately 1.2 times in comparison to free cells. The optimum conditions for hydrogen production by immobilized C. butyricum were initial pH 6.5 and initial sucrose concentration of 25 g COD/L. The maximum HPR and hydrogen yield (HY) of 3.11 L H₂/L substrate·d and 1.34 mol H₂/mol hexose consumed, respectively, were obtained. Results from repeated batch fermentation indicated that the highest HPR of 3.5 L H₂/L substrate·d and the highest HY of 1.52 mol H₂/mol hexose consumed were obtained at the medium replacement ratio of 75% and 50% respectively. The major soluble metabolites in both batch and repeated batch fermentation were butyric and acetic acids.     

The effect of Ni,Fe and Mg concentration on photo-hydrogen production by Rhodopseudomonas faecalis RLD-53

In the present study, the effect of Ni²⁺ (0–10 μmol/l), Fe²⁺ (0–200 μmol/l) and Mg²⁺ (0–15 mmol/l) concentration on photo-hydrogen production from acetate was investigated by batch culture. Results showed that under a proper concentration range, Ni²⁺ was able to enhance the hydrogen production rate and the hydrogen yield; Fe²⁺ was able to increase the hydrogen yield, and hydrogen production rate was enhanced only when the culturing time was 24–72 h. Ni²⁺ and Fe²⁺ at a higher concentration inhibited cell growth. When Ni²⁺ and Fe²⁺ concentrations were 4 μmol/l and 80 μmol/l, respectively, maximal hydrogen yield of 2.87 and 2.78 mol H₂/mol acetate was obtained when batch culturing at 35 °C with initial pH 7.0. Mg²⁺ did not significantly affect hydrogen production and hydrogen yield which maintained at about 2.45 mol H₂/mol acetate, but it was favorable to cell growth.     

Ag3PO4 photocatalyst: Hydrothermal preparation and enhanced O2 evolution under visible-light irradiation

Visible-light-driven semiconducting photocatalysts of Ag₃PO₄ were prepared by a hydrothermal method, and were optimized by adjusting reaction conditions, i.e., temperature, pH of reaction solution, concentration of feedstock, and time of hydrothermal process. The obtained photocatalysts were then systematically characterized by different instruments, such as XRD, UV–vis, FESEM, and BET, to reveal the physicochemical properties. Furthermore, activities of photocatalysts for visible-light-driven O₂ evolution were evaluated, demonstrating that the photocatalytic activity of Ag₃PO₄ prepared by hydrothermal reaction (initial rate of O₂ evolution, 1156 μmol g⁻¹ h⁻¹) was more than two times as that of sample prepared by room-temperature reaction (initial rate of O₂ evolution, 533 μmol g⁻¹ h⁻¹), which could be attributed to its better ability to utilize visible light and more regulated morphology.     

Highly solar active Fe(III) immobilised alumina for the degradation of Acid Violet 7

The hetero-Fenton catalyst Fe(III)-Al₂O₃ was prepared and characterised by ICP-AES, FT-IR and SEM-EDX. A detailed investigation of photocatalytic degradation of Acid Violet 7 (AV 7) using this Fenton immobilised Al₂O₃ catalyst was carried out. The optimal reaction conditions for the photodegradation of AV 7 with this catalyst are reported. Higher efficiency of the catalyst in solar light than in UV light makes this heterophoto-Fenton degradation, a green technological process. The catalyst is found to be stable and reusable. The completion of degradation has also been confirmed by chemical oxygen demand (COD) measurements.     

Self-doped Ti@TiO2 visible light photocatalyst: Influence of synthetic parameters on the H2 production activity

Self-doped TiO₂ shows visible light photocatalytic activity, while pristine TiO₂ is only UV responsive. Ti³⁺ has been demonstrated to be responsible for this improvement. We systematically studied various experimental parameters, such as the amount of reducing agent imidazole, types of imidazoles and Ti sources, and determined effects of these parameters on the combustion process and final materials. The phase composition, Ti³⁺ concentration, light absorption, surface area, and crystallinity of the product are significantly affected by the amount of imidazoles. Through comparing different imidazoles, we found that only flammable/combustible imidazoles are able to convert Ti⁴⁺ into Ti³⁺. This result is very helpful in understanding the mechanism and reactions in combustion process. Titanium precursors also have a great influence in production of Ti³⁺ doped TiO₂ materials. Titanium alkoxides allow the successful synthesis of blue partially reduced TiO₂, while TiCl₄ only lead to white pristine TiO₂.     

Influence of impregnation with lactic acid on sugar yields from steam pretreatment of sugarcane bagasse and spruce, for bioethanol production

Lignocellulosic biomass can be utilized to produce ethanol, a promising alternative energy source produced through fermentation of sugars. However, in order to achieve high sugar and ethanol yields, the lignocellulosic material must be pretreated before the enzymatic hydrolysis and fermentation. Dilute acid pretreatment, using SO₂, is one of the most promising methods of pretreatment for softwood and agricultural residues. However, handling the high acidity of the slurry obtained from pretreatment and difficulty in recycling/degradation of the impregnating agent are some of the drawbacks of the dilute acid processes. In the present study the influence of utilization of a weak organic acid (lactic acid), as impregnating agent, on the sugar yield from pretreatment, with and without addition of SO₂, was investigated. The efficiency of pretreatment was assessed by enzymatic hydrolysis of the slurry obtained by pretreatment, using sugarcane bagasse and spruce, stored for one and two months in the presence of lactic acid separately, as feedstocks. Pretreatment of bagasse after storage with 0.5% lactic acid resulted in an overall glucose yield, i.e. after enzymatic hydrolysis, of 79% of theoretical based on the amount available in the raw material. This was as good as pretreatment using SO₂ as impregnating agent. However, storage of spruce with lactic acid before pretreatment, with and without addition of SO₂, was not efficient and resulted in lower sugar yields than pretreatment using SO₂ only.     

Morphological, optical and photocatalytic properties of TiO2–Fe2O3 multilayers

Morphological, optical and photocatalytic properties of TiO₂, Fe₂O₃ and TiO₂–Fe₂O₃ samples (formed by 1, 3 and 5 coatings) were studied. The layers were deposited on glass substrate by the sol–gel method. The catalytic activity of the samples was studied by the photodecomposition of methylene blue (MB) under visible light illumination. The FTIR results indicate that all samples present surface OH radicals that are bound either to the Ti or Fe atoms. This effect is better visualized at larger number of coatings in the TiO₂–Fe₂O₃/glass systems. Also, two mechanisms are observed during the photodecomposition of the MB.     

Photoelectrochemical study on charge transfer properties of nanostructured Fe2O3 modified by g-C3N4

Novel photocatalysts, which consist of two visible light responsive semiconductors including graphite-like carbon nitride (g-C₃N₄) and Fe₂O₃, were successfully synthesized via electrodeposition followed by chemical vapor deposition. The morphology of the g-C₃N₄/Fe₂O₃ can be tuned from regular nanosheets to porous cross-linked nanostructures. Remarkably, the optimum activity of the g-C₃N₄/Fe₂O₃ is almost 70 times higher than that of individual Fe₂O₃ for photoelectrochemical water splitting. The enhancement of photoelectrochemical activity could be assigned to the morphology change of the photocatalysts and the effective separation and transfer of photogenerated electrons and holes originated from the intimately contacted interfaces. The g-C₃N₄/Fe₂O₃ composites could be developed as high performance photocatalysts for water splitting and other optoelectric devices.     

Rate-controlling species for the sintering of LiTi2(PO4)3

A series of Li deficient LiTi₂(PO₄)₃ samples were prepared and sintered and the density was measured to determine the rate-controlling species for sintering of LiTi₂(PO₄)₃. It was observed that as the Li content decreased the density decreased. This result suggests that oxygen does not control sintering. A comparison of the LiTi₂(PO₄)₃ sintering data to sintering and diffusion data in olivine, which exhibits a similar framework structure to LiTi₂(PO₄)₃, suggests that P is the species which controls sintering. This suggestion was confirmed by the density results of a Li excess LiTi₂(PO₄)₃ sample.     

Synthesis and characterization of Li3V(2 − 2x/3)Mgx(PO4)3/C cathode material for lithium-ion batteries

Li₃V_{(2 − 2x/3)}Mg_x(PO₄)₃/C (x = 0, 0.15, 0.30, 0.45) composites have been synthesized by the sol-gel assisted solid state method, using adipic acid C₆H₁₀O₄ (hexanedioic acid) as carbon source. The particle size of the composites is ∼1 μm. During the pyrolysis process, Li₃V_{(2 − 2x/3)}Mg_x(PO₄)₃/C network structure is formed. The effect of Mg²⁺ doped on the electrochemical properties of Li₃V₂(PO₄)₃/C positive materials has been studied. Li₃V_1.8Mg_0.30(PO₄)₃/C as the cathode materials of Li-ion batteries, the retention rate of discharge capacity is 91.4% (1 C) after 100 cycles. Compared with Li₃V₂(PO₄)₃/C, Li₃V_{(2 − 2x/3)}Mg_x(PO₄)₃/C composites have shown enhanced capacity and retention rate capability. The long-term cycles and ex situ XRD tests disclose that Li₃V_1.8Mg_0.30(PO₄)₃ exhibits higher structural stability than the undoped system.     

Electrochemical properties of LiFe0.9Mn0.1PO4/Fe2P cathode material by mechanical alloying

LiFePO₄, olivine-type LiFe_0.9Mn_0.1PO₄/Fe₂P composite was synthesized by mechanical alloying of carbon (acetylene back), M₂O₃ (M = Fe, Mn) and LiOH·H₂O for 2 h followed by a short-time firing at 900 °C for only 30 min. By varying the carbon excess different amounts of Fe₂P second phase was achieved. The short firing time prevented grain growth, improving the high-rate charge/discharge capacity. The electrochemical performance was tested at various C/x-rate. The discharge capacity at 1C rate was increased up to 120 mAh g⁻¹ for the LiFe_0.9Mn_0.1PO₄/Fe₂P composite, while that of the unsubstituted LiFePO₄/Fe₂P and LiFePO₄ showed only 110 and 60 mAh g⁻¹, respectively. Electronic conductivity and ionic diffusion constant were measured. The LiFe_0.9Mn_0.1PO₄/Fe₂P composite showed higher conductivity and the highest diffusion coefficient (3.90 × 10⁻¹⁴ cm² s⁻¹). Thus the improvement of the electrochemical performance can be attributed to (1) higher electronic conductivity by the formation of conductive Fe₂P together with (2) an increase of Li⁺ ion mobility obtained by the substitution of Mn²⁺ for Fe²⁺.     

Study on photocurrent of bilayers photoanodes using different combination of WO3 and Fe2O3

Bilayer photoanodes were prepared onto glass substrates (FTO) in order to improve generated photocurrents using UV-vis light by water splitting process. A comparative study of photocatalytic was performed over the films surface using Fe₂O_3, WO₃ and mixture of bicomponents (Fe₂O₃:WO₃). Different types of films were prepared using Fe₂O_3, WO₃ and bicomponents (mixture) on FTO substrates. The films were grown by sol gel method with the PEG-300 as the structure-directing agent. The photo-generated of the samples were determined by measuring the currents and voltages under illumination of UV-vis light. The morphology, structure and related composition distribution of the films have been characterized by SEM, XRD and EDX respectively. Photocurrent measurements indicated surface roughness as the effective parameter in this study. The deposited surfaces by bicomponents or mixture are flat without any feature on the surface while the deposited surfaces by WO₃ appears rough surface as small round (egg-shaped particles) and cauliflower-like. The surface deposited by Fe₂O₃ show rough no as well as WO₃ surface. The deposited surfaces by WO₃ reveal the higher value of photocurrent measurement due to surface roughness. Indeed, the roughness can be effective in increasing contact surface area between film and electrolyte and diffuse reflection (light scattering effect). The solution (Fe₂O₃:WO₃) shows the low photocurrent value in compare to WO₃ and Fe₂O₃ hat it may be due to decomposition the compound at 450 ± 1 °C to iron-tungstate Fe₂(WO₄)₃.     

Formation of multilayer-Eosin Y-sensitized TiO2 via Fe coupling for efficient visible-light photocatalytic hydrogen evolution

An efficient visible-light active photocatalyst of multilayer-Eosin Y-sensitized TiO₂ is prepared through linkage of Fe³⁺ between not only TiO₂ and Eosin Y but also different Eosin Y molecules to form three-dimensional polymeric dye structure. The multilayer-dye-sensitized photocatalyst is found to have high light harvesting efficiency and photocatalytic activity for hydrogen evolution under visible light irradiation (λ > 420 nm). On the optimum conditions (1:1 initial molar ratio of Eosin Y to Fe(NO₃)₃, initial 10 × 10⁻³ M Eosin Y, and 1.0 wt% Pt deposited by in situ photoreduction), its maximal apparent quantum yield for hydrogen evolution is 19.1% from aqueous triethanolamine solution (TEOA aq). The present study highlights linking between dye molecules via metal ions as a general way to develop efficient visible-light photocatalyst.     

Novel synthesis of LiFePO4-Li3V2(PO4)3 composite cathode material by aqueous precipitation and lithiation

LiFePO₄-Li₃V₂(PO₄)₃ composite cathode material is synthesized by aqueous precipitation of FeVO₄·xH₂O from Fe(NO₃)₃ and NH₄VO₃, following chemical reduction and lithiation with oxalic acid as the reducer and carbon source. Samples are characterized by XRD, SEM and TEM. XRD pattern of the compound synthesized at 700 °C indicates olivine-type LiFePO₄ and monoclinic Li₃V₂(PO₄)₃ are co-existed. TEM image exhibits that LiFePO₄-Li₃V₂(PO₄)₃ particles are encapsulated with a carbon shell 5-10 nm in thickness. The LiFePO₄-Li₃V₂(PO₄)₃ compound cathode shows good electrochemical performance, and its discharge capacity is about 139.1 at 0.1 C, 135.5 at 1 C and 116 mA h g⁻¹ at 3 C after 30 cycles.     

Improved separation efficiency of photogenerated carriers for Fe2O3/SrTiO3 heterojunction semiconductor

To investigate the mechanisms of the improvement on separation efficiency of photogenerated carriers, a Fe₂O₃/SrTiO₃ heterojunction semiconductor with an improved separation efficiency was successfully prepared. The heterojunction semiconductor was characterized with X-ray diffraction (XRD), UV–vis absorption spectrum, scanning electron microscope (SEM) and surface photovoltage (SPV) spectroscopy. The energy band diagrams of Fe₂O₃ and SrTiO₃ were determined with X-ray photoelectron spectroscopy (XPS), based on which the conduction band offset (CBO) between Fe₂O₃ and SrTiO₃ was quantified to be 1.26 ± 0.03 eV. The recombination of photogenerated carriers was investigated with photoluminescence (PL) spectrum, which indicates that the formation of Fe₂O₃/SrTiO₃ decreases the recombination. Thus the improved separation efficiency is mainly due to the energy difference between the conduction band edges of Fe₂O₃ and SrTiO₃, and the decreased electron-hole recombination for Fe₂O₃/SrTiO₃.     

Optimized solid-state synthesis of LiFePO4 cathode materials using ball-milling

Olivine-type LiFePO₄ cathode materials were synthesized by a solid-state reaction method and ball-milling. The ball-milling time, heating time and heating temperature are optimized. A heating temperature higher than 700 °C resulted in the appearance of impurity phase Fe₂P and growth of large particle, which was shown by high resolution X-ray diffraction and field emission scanning electron microscopy. The impurity phase Fe₂P exhibited a considerable capacity loss at the 1st cycle and a gradual increase in discharge capacity upon cycling. Moreover, it exhibited an excellent high-rate capacity of 104 mAh g⁻¹ at 3 C in spite of the large particle size. The optimum synthesis conditions for LiFePO₄ were ball-milling for 24 h and heat-treatment at 600 °C for 3 h. LiFePO₄/Li cells showed an enhanced cycling performance and a high discharge capacity of 160 mAh g⁻¹ at 0.1 C.     

Understanding the effect of TiO2, VCl3, and HfCl4 on hydrogen desorption/absorption of NaAlH4

The main objective of this work was to investigate the different effects of transition metals (TiO₂, VCl₃, HfCl₄) on the hydrogen desorption/absorption of NaAlH₄. The HfCl₄ doped NaAlH₄ showed the lowest temperature of the first desorption at 85 °C, while the one doped with VCl₃ or TiO₂ desorbed at 135 °C and 155 °C, respectively. Interestingly, the temperature of desorption in subsequent cycles of the NaAlH₄ doped with TiO₂ reduced to 140 °C. On the contrary, in the case of NaAlH₄ doped with HfCl₄ or VCl₃, the temperature of desorption increased to 150 °C and 175 °C, respectively. This may be because Ti can disperse in NaAlH₄ better than Hf and V; therefore, this affected segregation of the sample after the desorption. The maximum hydrogen absorption capacity can be restored up to 3.5 wt% by doping with TiO₂, while the amount of restored hydrogen was lower for HfCl₄ and VCl₃ doped samples. XRD analysis demonstrated that no Ti-compound was observed for the TiO₂ doped samples. In contrast, there was evidence of Al–V alloy in the VCl₃ doped sample and Al–Hf alloy in the HfCl₄ doped sample after subsequent desorption/absorption. As a result, the V- or Hf-doped NaAlH₄ showed the lower ability to reabsorb hydrogen and required higher temperature in the subsequent desorptions.     

Organic–inorganic hybrid solar cells based on conducting polymer and SnO2 nanoparticles chemically modified with a fullerene derivative

Organic–inorganic hybrid solid solar cells were fabricated by using a conjugated polymer (MDMO-PPV) and SnO₂ nanoparticles chemically modified with C₆₀C(COOH)₂. The cell performance was improved by the chemical modification, suggesting that the modification with photoelectrochemically active organic materials is useful for establishing good electronic junction at the organic–inorganic interface. The short-circuit current density J_SC increased with increasing thickness of MDMO-PPV up to 40 nm, and then decreased gradually. This thickness dependence was explained by the fluorescence quenching of MDMO-PPV by Au electrode and the film resistance of MDMO-PPV.     

Landfill leachate treatment by solar-driven AOPs

Sanitary landfill leachate resulting from the rainwater percolation through the landfill layers and waste material decomposition is a complex mixture of high-strength organic and inorganic compounds which constitutes serious environmental problems. In this study, different heterogeneous (TiO₂/UV, TiO₂/H₂O₂/UV) and homogenous (H₂O₂/UV, Fe²⁺/H₂O₂/UV) photocatalytic processes were investigated as an alternative for the treatment of a mature landfill leachate. The addition of H₂O₂ to TiO₂/UV system increased the reduction of the aromatic compounds from 15% to 61%, although mineralization was almost the same. The DOC and aromatic content abatement is similar for the H₂O₂/UV and TiO₂/H₂O₂/UV processes, although the H₂O₂ consumption is three times higher in the H₂O₂/UV system. The low efficiency of TiO₂/H₂O₂/UV system is presumably due to the alkaline leachate solution, for which the H₂O₂ becomes highly unstable and self-decomposition of H₂O₂ occurs. The efficiency of the TiO₂/H₂O₂/UV system increased 10 times after a preliminary pH correction to 4. The photo-Fenton process is much more efficient than heterogeneous (TiO₂, TiO₂/H₂O₂/UV) or homogeneous (H₂O₂/UV) photocatalysis, showing an initial reaction rate more than 20 times higher, and leading to almost complete mineralization of the wastewater. However, when compared with TiO₂/H₂O₂/UV with acidification, the photo-Fenton reaction is only two times faster.The optimal initial iron dose for the photo-Fenton treatment of the leachate is 60 mg Fe²⁺ L⁻¹, which is in agreement with path length of 5 cm in the photoreactor. The kinetic behaviour of the process (60 mg Fe²⁺ L⁻¹) comprises a slow initial reaction, followed by a first-order kinetics (k = 0.020 , r₀ = 12.5 mg ), with H₂O₂ consumption rate of k_H2O2 = 3.0 mmol H₂O₂, and finally, the third reaction period, characterized by a lower DOC degradation and H₂O₂ consumption until the end of the experiment, presumably due to the formation of low-molecular-weight carboxylic groups. A total of 306 mM of H₂O₂ was consumed for achieving 86% mineralization (DOC_final = 134 mg L⁻¹) and 94% aromatic content reduction after 110 kJ_UV L⁻¹, using an initial iron concentration of 60 mg Fe²⁺ L⁻¹.