Rheological properties in blends of poly(aryl ether ether ketone) and liquid crystalline poly(aryl ether ketone)

Rheological properties of the blends of poly(aryl ether ether ketone) (PEEK) with liquid crystalline poly(aryl ether ketone) containing substituted 3‐trifluoromethylbenzene side group (F‐PAEK), prepared by solution precipitation, have been investigated by rheometer. Dynamic rheological behaviors of the blends under the oscillatory shear mode are strongly dependent on blend composition. For PEEK‐rich blends, the systems show flow curves similar to those of the pure PEEK, i.e., dynamic storage modulus G′ is larger than dynamic loss modulus G″, showing the feature of elastic fluid. For F‐PAEK‐rich systems, the rheological behavior of the blends has a resemblance to pure F‐PAEK, i.e., G″ is greater than G′, showing the characteristic of viscous fluid. When the PEEK content is in the range of 50–70%, the blends exhibit an unusual rheological behavior, which is the result of phase inversion between the two components. Moreover, as a whole, the complex viscosity values of the blends are between those of two pure polymers and decrease with increasing F‐PAEK content. However, at 50% weight fraction of PEEK, the viscosity‐composition curves exhibit a local maximum, which may be mainly attributed to the phase separation of two components at such a composition. The changes of G′ and G″ with composition show a trend similar to that of complex viscosity. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4040–4044, 2006     

Molecular weight determination of poly(phenylene sulfide ether)

Poly(phenylene sulfide ether) and poly(phenylene sulfoxide ether sulfide ether) (PPSOESE) were successfully prepared and their structures were proved by several analytical techniques in the present work. The molecular weight (MW) of PPSOESE, a soluble polymer in common organic solvent at room temperature, was determined by gel permeation chromatography. Based on the conversion reaction of the two polymers, the MW of PPSE was calculated and correlated with its intrinsic viscosity. As a result, the Mark‐Houwink equation for PPSE was concluded. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Comparison of interdiffusion at polystyrene–poly(vinyl methyl ether) and polystyrene–poly(isobutyl vinyl ether) interfaces

The effect of polymer–polymer compatibility on interdiffusion at polymer interfaces with dissimilar mobilities was investigated by attenuated total internal reflectance infrared spectroscopy. The polymer pair consisting of polystyrene and poly(vinyl methyl ether) was used to study interdiffusion at the interface of compatible polymers. The polymer pair consisting of polystyrene and poly(isobutyl vinyl ether) was used to study interdiffusion at the interface of incompatible polymers. Results indicate that the extent of interdiffusion is controlled by the polymer–polymer compatibility parameter, irrespectively of the differences in the mobility of the polymers.     

Synthesis and characterization of thermotropic liquid crystalline poly(aryl ether ketone) copolymers with pendant 3‐(trifluoromethyl) phenyl groups

Novel poly(aryl ether ketone) copolymers with pendant 3‐(trifluoromethyl)phenyl groups were synthesized by the reaction of a crystal‐disrupting monomer, 3‐(trifluoromethyl)phenylhydroquinone (FH) and a mesogenic monomer, 4,4′‐biphenol (BP) with 1,4‐bis(p‐fluorobenzoyl)benzene (BF). Thermotropic liquid crystalline behavior of the copolymers was investigated by means of differential scanning calorimetry, polarized optical microscope and wide‐angle X‐ray diffraction. As a result, the copolymers with the respective molar ratios of FH/BP/BF of 0/100/100–10/90/100 and 80/20/100–100/0/100 were semi‐crystalline without liquid crystalline properties, and amorphous polymers, respectively. In contrast, copolymers with the molar ratio of FH/BP/BF of 20/80/100–70/30/100 had liquid crystalline characteristics. Interestingly, the formation of a highly ordered smectic phase was confirmed for copolymers with the molar ratio of FH/BP/BF of 20/80/100–50/50/100, respectively. All the liquid crystalline copolymers had a wide liquid crystalline temperature range (57–75 °C). Copyright © 2006 Society of Chemical Industry     

高分子量聚醋酸乙烯酯的醇解研究

探讨了催化剂浓度、醇解温度和反应时间等对高分子量聚醋酸乙烯酯醇解的影响,得出高分子量聚醋酸乙烯酯醇解的适合条件。     

Development of stealth nanoparticles coated with poly(2-methoxyethyl vinyl ether) as an alternative to poly(ethylene glycol)

Poly(ethylene glycol) (PEG) modification, also known as PEGylation, has been extensively used to improve the stability of nanoparticles for nanomedical applications. However, PEG exhibits antigenicity in some formulations, motivating researchers to explore alternative polymers. Herein, poly(vinyl ether) (PVE) derivatives are highlighted as promising alternatives to PEG because they form intermediate water molecules that suppress non-specific protein adsorption and platelet adhesion to the material surface. We prepared a water-soluble PVE derivative, poly(2-methoxyethyl vinyl ether) (PMOVE), and utilized it as a surface modifier for gold nanoparticles (AuNPs) as model nanoparticles. PMOVE with a thiol terminus was synthesized and confirmed to form an intermediate water molecule using differential scanning calorimetry. Similar to the synthesis of PEGylated AuNPs (PEG-AuNPs), PMOVE-modified AuNPs (PMOVE-AuNPs) were successfully fabricated with an appreciably high density of PMOVE palisades via a thiol-gold coordination reaction. Similar to PEG-AuNPs, PMOVE-AuNPs showed reduced serum protein adsorption and prolonged blood circulation. Additionally, no significant cytotoxicity was observed after incubation of a murine macrophage cell line, RAW264.7, with PMOVE-AuNPs. Our results indicate that the PMOVE modification increases the stealthiness of nanoparticles that is equivalent to that achieved by PEGylation.     

Blends of phenolphthalein poly(ether ether ketone) and a thermotropic liquid crystalline copolyester

Blends of phenolphthalein poly(ether ether ketone) (PEK-C) and a thermotropic liquid crystalline copolyester (LCP), poly[(1-phenylethyl-p-phenylene terephthalate)-co-(1-cumyl-p-phenylene terephthalate)], was prepared via melt mixing. The studies of differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) indicate that the PEK-C/LCP blends display two glass transition temperatures which correspond to those of PEK-C- and LCP-rich phases, respectively. The PEK-C/LCP blends were judged to be partially miscible. Scanning electron microscopy (SEM) was employed to examine the morphology of the blends, and it was observed that all the PEK-C/LCP blends displayed a phase-separated structure. The interface between the PEK-C- and LCP-rich phases is poor. The Young's modulus of the PEK-C/LCP blends was found to increase with LCP content due to the high modulus of the LCP. However, the tensile strength and the elongation at break of the blends greatly decreases with increase of LCP content, owing to the poor interfacial adhesion. From the thermogravity analysis (TGA), it was observed that all the blends exhibited a two-step weight loss mechanism, and the thermal degradation onset temperature of the blends was lowered with the addition of LCP content. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1923–1931, 1998     

Formation of polymer-polymer complexes and blends in the system poly(acrylic acid)-poly(vinyl methyl ether)

The formation of a 1:1 polymer-polymer complex from poly(acrylic acid) and poly(vinyl methyl ether) has been detected by viscosity measurements in aqueous solution, and the glass transition temperature of the isolated complex has been determined. Infrared spectroscopy indicates that specific hydrogen bonding occurs between the components of the complex. Miscible blends of the two polymers can also be formed (at all compositions) and, although hydrogen bonding occurs, the structures of the blends are likely to be dissimilar to that of the complex.     

Reinforced poly(ether sulfone) materials by blending with a semiaromatic liquid crystalline copolyester

Blends based on poly(ether sulfone) (PES) and a semiaromatic liquid crystalline copolyester (R5) were obtained by injection molding across the entire composition range. The blends showed two pure amorphous phases. The fibrillar structure of the skin led to enhancements in the stiffness. The break properties, however, decreased at low LCP contents, due to the expected lack of adhesion between the phases. The increase in the modulus at increasing LCP content led to improvements in tensile strength. The notch sensitivity of PES decreased after the addition of low LCP levels, giving rise to enhancements of almost 600% in the notched impact strength. The unusually enhanced performance of the 20/80 blend, which has been seen previously in another thermoplastic/LCP blend, suggests that the dispersed PES phase in this blend may act as rubber particles do in rubber toughened thermoplastics. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 52–59, 2004     

Effect of stereoregularity and molecular weight on the mechanical properties of poly(vinyl alcohol) hydrogel

The effect of the stereoregularity and molecular weight of poly(vinyl alcohol) (PVA) on the mechanical properties of hydrogel was investigated. Compressive strength, creep behavior, and dynamic viscoelasticity were measured on hydrogels of syndiotacticity‐rich PVA derived from poly(vinyl pivalate) (D_p = 1690 diad‐syndiotacticity = 61%, D_p = 8020 diad‐syndiotacticity = 62%) and atactic PVA (D_p = 1750 diad‐syndiotacticity = 54%, D_p = 7780 diad‐syndiotacticity = 54%). Increasing the molecular weight of molecular chains constituting the gel improved the compressive strength of atactic PVA hydrogel. The stereoregularity of PVA had a greater effect than molecular weight on the strength of the hydrogel. Gel prepared from 8.8 g/dL syndiotacticity‐rich PVA had a high compressive modulus of 10 kPa, and the compressive modulus of the gel prepared from 3.3 g/dL was comparable with that of atactic PVA hydrogel prepared with more than 6 g/dL. The dynamic storage modulus of the gel derived from syndiotacticity‐rich PVA was remarkably higher than that of the atactic PVA gel and remained constant up to 60°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

氯化橡胶与氯醚树脂的合成与应用

介绍了氯化橡胶的应用及其合成方法,以及作为取代氯化橡胶应用于防腐材料中的氯醚树脂的主要合成方法。通过使用2种材料制成的漆的性能比较发现,氯醚树脂这种环保性更好的材料完全可以取代氯化橡胶,并且有更好的发展前景。     

Characteristics of poly(ether ether ketone) microporous membranes prepared via thermally induced phase separation (TIPS)

The morphology and bulk properties of microporous membranes based on poly (ether ether ketone) (PEEK) have been investigated as a function of initial casting composition and thermal and mechanical processing history. Membranes were prepared via solid—liquid phase separation of miscible blends of PEEK and polyetherimide (PEI), with subsequent extraction of the PEI diluent. Scanning electron microscopy studies revealed a microporous morphology with two distinct pore size scales corresponding to diluent extraction from interfibrillar and interspherulitic regions, respectively. The membrane structure was sensitive to both initial blend composition and crystallization temperature, with the resulting pore size distribution reflecting the kinetics of phase separation. For membranes prepared with lower initial diluent content or at lower crystallization temperatures, mercury intrusion porosimetry indicated a relatively narrow distribution of fine interfibrillar pores, with an average pore size of approximately 0.04 microns. Membranes prepared at higher diluent content or at higher crystallization temperatures displayed a broad pore distribution, with a sizeable population of coarse, interspherulitic pores (0.1 to 1 μm in size). Uniaxial drawing led to a fibrillated network structure with markedly higher water flux characteristics compared to the as-cast membranes. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 2347–2355, 1997     

Iodination of plasticized poly(vinyl chloride) in aqueous media via phase transfer catalysis

Nucleophilic substitution of chlorine on plasticized poly(vinyl chloride) (PVC) was carried out using potassium iodide (KI) in the presence of a phase transfer catalyst (PTC) in aqueous media. Iodination was confirmed using energy dispersive X‐ray analysis (EDAX). The extent of iodination was studied with respect to time, temperature, concentration of the reactants, as well as different PTCs. Among the different PTCs examined, tetrabutylammonium bromide (TBAB) and tetrabutylammonium hydrogen sulfate (TBAH) were found to be highly efficient for the reaction. About 25% increase in weight was observed for PVC sheets iodinated under optimal reaction conditions. The thermal stability of the modified PVC was found to be impaired upon iodination. The iodinated PVC released iodide ions when kept in distilled water, as evidenced by UV spectroscopy. Sustained release of iodide ion in distilled water was followed up for about 30 days. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 493–499, 2002; DOI 10.1002/app.10176     

Fine poly(ether ether ketone) powders

The physical form of polymers is often important for carrying out subsequent processing operations. For example, fine powders are desirable for molding and sintering compounds because they consolidate to produce void free components. The objective of this work is to prepare fine polymeric particulates suitable for processing into fiber reinforced polymer matrix composites. Micron size particles of poly(ether ether ketone) (PEEK) were prepared by rapidly quenching solutions of these materials. PEEK pellets were dissolved at temperatures near the PEEK melting point in a mixture of terphenyls and quaterphenyls; then the solution was quenched to a temperature between the T_g and T_m (≈ 225°C) by adding a room temperature eutectic mixture of diphenyl ether and biphenyl. A supersaturated, metastable solution of PEEK resulted, causing rapid nucleation. Fine PEEK particles rapidly crystallized from this solution. The average particle size was measured using transmission electron microscopy, atomic force microscopy, and by light scattering of aqueous suspensions which had been fractionated by centrifugation. The average particle diameter was about 0.6 μm. Three dimensional photomicrographs obtained via atomic force microscopy showed some aggregates in the suspensions. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 63: 1571–1578, 1997     

Synthesis and properties of thio‐containing poly(ether ether ketone)s

A series of thio‐containing poly(ether ether ketone) (PEESK) polymers was synthesized by the introduction of thio groups from 4,4′ thiodiphenol (TDP) into the poly(ether ether ketone) (PEEK) structure via reaction between the phenol and aromatic fluoride groups. The effect of the thio groups on the properties of the PEESK materials was investigated. Differential scanning calorimetry (DSC) analysis and X‐ray diffraction (XRD) patterns show a depression in the crystallinity of the PEESKs with incorporation of the content of thio groups in the backbones. The crystalline structure was identified as an orthorhombic structure with lattice constants of a = 7.52 Å, b = 5.86 Å and c = 10.24 Å for all crystallizable PEESKs. The crystalline structures of the thio‐containing PEEK polymers were the same as that of the neat PEEK, which means the thio‐containing block in the whole thio‐containing PEEK molecule is almost excluded from the crystalline structure and the crystals are completely formed by ‘non‐thio’ blocks only. Due to the glass transition temperature (T_g) and melting temperature (T_m) depression with increase in the TDP content in the reaction system, the processability of the resultant thio‐containing PEEKs could be effectively improved. Copyright © 2004 Society of Chemical Industry     

CO2-permselective membranes of crosslinked poly(vinyl ether)s bearing oxyethylene chains

Cationic copolymerizations of vinyl ether monomers having a triethylene glycol segment [2-(2-(2-methoxyethoxy)ethoxy)ethyl vinyl ether (TEGMVE)] with vinyl ether monomer having a methacrylate unit [2-(2-vinyloxyethoxy)ethyl methacrylate: VEEM] were performed to obtain crosslinkable copolymers [poly(TEGMVE-VEEM)] with different composition rates. Methacrylate groups in poly(TEGMVE-VEEM)s partially reacted to give crosslinked polymer membranes. The free-standing membranes of poly(TEGMVE-VEEM)s obtained at monomer feed ratios of 6:1, 10:1, and 14:1 were too brittle, while their composite membranes with PTFE sheet were tough enough to measure gas permeability. All the membranes of poly(TEGMVE-VEEM) showed high CO₂/N₂ selectivity (PCO₂/PN₂$P_{{\text{CO}}_2}/P_{{\text{N}}_2}$ = 35–54) because of their high CO₂ solubility selectivity (SCO₂$S_{{\text{CO}}_2}$/SN₂$S_{{\text{N}}_2}$ = 38–61). The gas permeability increased as the composition ratio of VEEM decreased, and the composite membrane of poly(TEGMVE-VEEM)(14:1) showed the highest CO₂ permeability (PCO₂$P_{{\text{CO}}_2}$ = 410 barrers) among the present polymer membranes.     

Impact behavior of phenolphthalein poly(ether sulfone)/ultrahigh molecular weight polyethylene blends

This work presents the structure and impact properties of phenolphthalein poly(ether sulfone) blended with ultrahigh molecular weight polyethylene (PES-C/UHMWPE) at different compositions. The addition of UHMWPE can considerably improve the Charpy and Izod impact strength of the blends. The fracture surface is examined to demonstrate the toughening mechanics related to the modified PES-C resin. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67: 113–118, 1998     

Thermal properties of melt‐blended poly(ether ether ketone) and poly(ether imide)

The thermal properties of blends of poly(ether ether ketone) (PEEK) and poly(ether imide) (PEI) prepared by screw extrusion were investigated by differential scanning calorimetry. From the thermal analysis of amorphous PEEK–PEI blends which were obtained by quenching in liquid nitrogen, a single glass transition temperature (T_g) and negative excess heat capacities of mixing were observed with the blend composition. These results indicate that there is a favorable interaction between the PEEK and PEI in the blends and that there is miscibility between the two components. From the Lu and Weiss equation and a modified equation from this work, the polymer–polymer interaction parameter (χ₁₂) of the amorphous PEEK–PEI blends was calculated and found to range from −0.058 to −0.196 for the extruded blends with the compositions. The χ₁₂ values calculated from this work appear to be lower than the χ₁₂ values calculated from the Lu and Weiss equation. The χ₁₂ values calculated from the T_g method both ways decreased with increase of the PEI weight fraction. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 733–739, 1999     

Properties of branched and network poly(vinyl alcohols) prepared with poly(vinyl alcohol) having aldehyde groups at the chain ends

Branched and network poly(vinyl alcohols) (PVAs) were prepared with inter-acetalization of the PVA with aldehyde groups at the chain ends which was prepared by the cleavage of 1,2 glycol bonds in commercial PVA. The numbers of branches estimated from molecular weights were compared with those estimated by theory. Huggins' constant and crystallinity decreased with increasing branch number. Dissolution of branched PVAs into dimethylsulphoxide was not so easy compared with commercial PVA. The colour of branched PVA–iodine complex decreased rapidly with standing while that of commercial PVA decreased gradually. Network PVAs with Young's modulus of 1–8 MPa were prepared.