Nanoporous Ultra‐Low‐Dielectric‐Constant Fluoropolymer Films via Selective UV Decomposition of Poly(pentafluorostyrene)‐block‐Poly(methyl methacrylate) Copolymers Prepared Using Atom Transfer Radical Polymerization

Block copolymers of poly(pentafluorostyrene) (PFS) and poly(methyl methacrylate) (PMMA) (PFS‐b‐PMMA) have been synthesized using atom transfer radical polymerization (ATRP). Then, nanoporous fluoropolymer films have been prepared via selective UV decomposition of the PMMA blocks in the PFS‐b‐PMMA copolymer films. The chemical composition and structure of the PFS homopolymers and copolymers have been characterized using nuclear magnetic resonance (NMR) spectroscopy, thermogravimetric analysis (TGA), X‐ray photoelectron spectroscopy (XPS), time‐of‐flight secondary‐ion mass spectrometry (ToF‐SIMS), and molecular‐weight measurements. The cross‐sectional and surface morphologies of the PFS‐b‐PMMA copolymer films before and after selective UV decomposition of the PMMA blocks have been studied using field‐emission scanning electron microscopy (FESEM). The nanoporous fluoropolymer films with pore sizes in the range 30–50 nm and porosity in the range 15–40 % have been obtained from the PFS‐b‐PMMA copolymers of different PMMA content. Dielectric constants approaching 1.8 have been achieved in the nanoporous fluoropolymer films which contain almost completely decomposed PMMA blocks.     

Ultra‐Low‐Power Differential ISFET/REFET Readout Circuit

A novel ultra‐low‐power readout circuit for a pH‐sensitive ion‐sensitive field‐effect transistor (ISFET) is proposed. It uses an ISFET/reference FET (REFET) differential pair operating in weak‐inversion and a simple current‐mode metal‐oxide semiconductor FET (MOSFET) translinear circuit. Simulation results verify that the circuit operates with excellent common‐mode rejection ability and good linearity for a single pH range from 4 to 10, while only 4 nA is drawn from a single 1 V supply voltage.     

多信道非线性平面光波导的空间光弧子开关

本文考虑在横向具有正弦形周期折射率调制的非线性平面光波导，它构成平行的多信道系统。分别用解析法和BPM数值方法探索在该系统中稳定传输的空间光弧子实现开关的可能性。研究结果表明：只要控制光点强度超过某一阈值，开关是可以发生的。     

Low‐Voltage,High‐Performance Organic Field‐Effect Transistors with an Ultra‐Thin TiO2 Layer as Gate Insulator

We report on our latest improvements in organic field‐effect transistors (OFETs) using ultra‐thin anodized gate insulators. Anodization of titanium (Ti) is an extremely cheap and simple technique to obtain high‐quality, very thin (～ 7.5 nm), pinhole‐free, and robust gate insulators for OFETs. The anodized insulators have been tested in transistors using pentacene and poly(triarylamine) (PTAA) as active layers. The fabricated devices display low‐threshold, normally “off” OFETs with negligible hysteresis, good carrier mobility, high gate capacitance, and exceptionally low inverse subthreshold slope. Device performance is improved via chemical modification of TiO₂ with an octadecyltrichlorosilane (OTS) self‐assembled monolayer (SAM). As the result of this combination of favorable properties, we have demonstrated OFETs that can be operated with voltages well below 1 V.     

A Low‐Bandgap Semiconducting Polymer for Photovoltaic Devices and Infrared Emitting Diodes

A novel low‐bandgap conjugated polymer (PTPTB, E_g = ∼ 1.6 eV), consisting of alternating electron‐rich N‐dodecyl‐2,5‐bis(2′‐thienyl)pyrrole (TPT) and electron‐deficient 2,1,3‐benzothiadiazole (B) units, is introduced for thin‐film optoelectronic devices working in the near infrared (NIR). Bulk heterojunction photovoltaic cells from solid‐state composite films of PTPTB with the soluble fullerene derivative [6,6]‐phenyl C₆₁ butyric acid methyl ester (PCBM) as an active layer shows promising power conversion efficiencies up to 1 % under AM1.5 illumination. Furthermore, electroluminescent devices (light‐emitting diodes) from thin films of pristine PTPTB show near infrared emission peaking at 800 nm with a turn on voltage below 4 V. The electroluminescence can be significantly enhanced by sensitization of this material with a wide bandgap material such as the poly(p‐phenylene vinylene) derivative MDMO‐PPV.     

InP‐Based Polarization‐Insensitive Planar Waveguide Concave Grating Demultiplexer with Flattened Spectral Response

InP‐based planar waveguide 48‐channel concave grating demultiplexers with a channel spacing of 0.8 nm (100 GHz) are described and demonstrated. Polarization insensitivity and flattened spectral response are successfully achieved by the introduction of a polarization compensator and a two‐focus grating, respectively. The fabricated device shows a polarization‐dependent wavelength shift of less than 20 pm and a ?3 dB spectral width of about 0.55 nm (68.75 GHz) over all channels.     

Light‐Guiding Biomaterials for Biomedical Applications

Optical techniques used in medical diagnosis, surgery, and therapy require efficient and flexible delivery of light from light sources to target tissues. While this need is currently fulfilled by glass and plastic optical fibers, recent emergence of biointegrated approaches, such as optogenetics and implanted devices, calls for novel waveguides with certain biophysical and biocompatible properties and desirable shapes beyond what the conventional optical fibers can offer. To this end, exploratory efforts have begun to harness various transparent biomaterials to develop waveguides that can serve existing applications better and enable new applications in future photomedicine. Here, the recent progress in this new area of research for developing biomaterial‐based optical waveguides is reviewed. It begins with a survey of biological light‐guiding structures found in plants and animals, a source of inspiration for biomaterial photonics engineering. The review then describes natural and synthetic polymers and hydrogels that offer appropriate optical properties, biocompatibility, biodegradability, and mechanical flexibility have been exploited for light‐guiding applications. Finally, perspectives on biomedical applications that may benefit from the unique properties and functionalities of light‐guiding biomaterials are discussed briefly.     

Reprintable Polymers for Digital Light Processing 3D Printing

3D printing is becoming a disruptive technology and shows great potential for various practical applications. Specially, digital light processing (DLP) 3D printing demonstrates advantages in high resolution and high efficiency. However, extensive production of infusible and insoluble thermosets in DLP printing causes serious resource waste and environmental problems after its disposal. Herein, a reprintable linear polymer is reported for repeatable DLP printing. Taking advantage of the dissolution of linear polymer in its monomer, printed objects can be recycled into liquid resin and reprinted via the same DLP. Polymerization kinetics and printing resolution of recycled resins and mechanical properties of reprinted polymers retain identical as the original. The thermoplastic nature of linear polymer endows 3D objects with welding and reshaping property. Recyclable composites are also successfully fabricated, and sustainable usage of high-value fillers comes true. This strategy helps to address environmental issues arising from unprocessable thermosets and may contribute to an efficient materials recycling.     

Optimization of Solubility,Film Morphology and Photodetector Performance by Molecular Side‐Chain Engineering of Low‐Bandgap Thienothiadiazole‐Based Polymers

A series of donor–acceptor (D‐A) type low‐bandgap polymers containing the terthiophene and thieno[3,4‐b]thiadiazole units in the main chain but different numbers of identical side chains are designed and synthesized in order to study the effect of side chain on the polymer properties and optimize the performance of polymer photodetectors. Variation in the side chain content can influence the polymer solubility, molecular packing, and film morphology, which in turn affects the photodetector performance, particularly with regard to the photoresponsivity and dark current. X‐ray diffraction patterns indicate that molecular ordering increases with more side chains. Atomic force microscopy shows that appropriate morphology of the active layer in the polymer photodetector is necessary for high photocurrent and low dark current. Using BCP as a hole blocking layer (10 nm), the photodetector based on P4 exhibits the optimized performance with specific detectivity of 1.4 × 10¹² Jones at 800 nm, which is among the best reported values for polymer photodetectors and even comparable to that of a silicon photodetector.     

Low‐Work‐Function Surface Formed by Solution‐Processed and Thermally Deposited Nanoscale Layers of Cesium Carbonate

Nanostructured layers of Cs₂CO₃ are shown to function very effectively as cathodes in organic electronic devices because of their good electron‐injection capabilities. Here, we report a comprehensive study of the origin of the low work function of nanostructured layers of Cs₂CO₃ prepared by solution deposition and thermal evaporation. The nanoscale Cs₂CO₃ layers are probed by various characterization methods including current–voltage (I–V) measurements, photovoltaic studies, X‐ray photoelectron spectroscopy (XPS), UV photoelectron spectroscopy (UPS), and impedance spectroscopy. It is found that thermally evaporated Cs₂CO₃ decomposes into CsO₂ and cesium suboxides. The cesium suboxides dope CsO₂, yielding a heavily doped n‐type semiconductor with an intrinsically low work function. As a result, devices fabricated using thermally evaporated Cs₂CO₃ are relatively insensitive to the choice of the cathode metal. The reaction of thermally evaporated Cs₂CO₃ with Al can further reduce the work function to 2.1 eV by forming an Al–O–Cs complex. Solution‐processed Cs₂CO₃ also reduces the work function of Au substrates from 5.1 to 3.5 eV. However, devices prepared using solution‐processed Cs₂CO₃ exhibit high efficiency only if a reactive metal such as Al or Ca is used as the cathode metal. A strong chemical reaction occurs between spin‐coated Cs₂CO₃ and thermally evaporated Al. An Al–O—Cs complex is formed as a result of this chemical reaction at the interface, and this layer significantly reduces the work function of the cathode. Finally, impedance spectroscopy results prove that this layer is highly conductive.     

Ultra‐Thin Self‐Assembled Protein‐Polymer Membranes: A New Pore Forming Strategy

Self‐assembled membranes offer a promising alternative for conventional membrane fabrication, especially in the field of ultrafiltration. Here, a new pore‐making strategy is introduced involving stimuli responsive protein‐polymer conjugates self‐assembled across a large surface area using drying‐mediated interfacial self‐assembly. The membrane is flexible and assembled on porous supports. The protein used is the cage protein ferritin and resides within the polymer matrix. Upon denaturation of ferritin, a pore is formed which intrinsically is determined by the size of the protein and how it resides in the matrix. Due to the self‐assembly at interfaces, the membrane constitutes of only one layer resulting in a membrane thickness of 7 nm on average in the dry state. The membrane is stable up to at least 50 mbar transmembrane pressure, operating at a flux of about 21 000–25 000 L m^?2 h^?1 bar^?1 and displayed a preferred size selectivity of particles below 20 nm. This approach diversifies membrane technology generating a platform for “smart” self‐assembled membranes.     

Ultra‐Smooth and Ultra‐Strong Ion‐Exchanged Glass as Substrates for Organic Electronics

The introduction of new substrate materials into the world of electronics has previously opened up new possibilities for novel applications and device designs. Here, the use of ion‐exchanged sodium aluminosilicate (NAS) glass is presented as a new type of substrate that is not only highly damage resistant, but also allows the fabrication of high performance organic electronic devices. The smoothness of the NAS glass surface enables favorable growth of the semiconductor layer, enabling high charge carrier mobilities for typical organic semiconductors, such as pentacene or C60, and a polymer semiconductor. No degradation of the device performance is observed as a result of ion migration into the active device region, and no compromise in substrate strength due to the processing conditions is made. This work suggests the possibility of new, highly durable electronic devices on glass in large area format.     

Low‐Power‐Photon Up‐Conversion in Dual‐Dye‐Loaded Polymer Nanoparticles

Sensitized triplet–triplet annihilation in multicomponent organic systems is already demonstrated to be suitable for obtaining efficient up‐conversion in solution with excitation power densities comparable to solar irradiance, but loses efficiency in the solid state. Here, it is demonstrated that it is possible to reduce this limitation by incorporating a standard bicomponent system in polymer nanoparticles. The confinement of all of the involved photophysical processes in a nanometer‐scale volume makes each nanoparticle a single and isolated high‐efficiency up‐converting unit. As a consequence, these dual‐dye‐loaded nanoparticles can be used to produce drop‐cast films, as well as dopants for polymeric matrices, preserving the performances of the starting moieties in solution.     

High‐Efficiency and Color Stable Blue‐Light‐Emitting Polymers and Devices

Novel fluorene‐based blue‐light‐emitting copolymers with an ultraviolet‐blue‐light (UV‐blue‐light) emitting host and a blue‐light emitting component, 4‐N,N‐diphenylaminostilbene (DPS) have been designed and synthesized by using the palladium‐ catalyzed Suzuki coupling reaction. It was found that both copolymers poly [2,7‐(9,9‐dioctylfluorene)‐alt‐1,3‐(5‐carbazolphenylene)] (PFCz) DPS1 and PFCz‐DPS1‐OXD show pure blue‐light emission even with only 1 % DPS units because of the efficient energy transfer from the UV‐blue‐light emitting PFCz segments to the blue‐light‐emitting DPS units. Moreover, because of the efficient energy transfer/charge trapping in these copolymers, PFCz‐DPS1 and PFCz‐DPS1‐OXD show excellent device performance with a very stable pure blue‐light emission. By using a neutral surfactant poly[9,9‐bis(6'‐(diethanolamino)hexyl)‐fluorene] (PFN‐OH) as the electron injection layer, the device based on PFCz‐DPS1‐OXD5 with the configuration of ITO/PEDOT:PSS/PVK/polymer/PFN‐OH/Al showed a maximum quantum efficiency of 2.83 % and a maximum luminous efficiency of 2.50 cd A^–1. Its CIE 1931 chromaticity coordinates of (0.156, 0.080) match very well with the NTSC standard blue pixel coordinates of (0.14, 0.08). These results indicate that this kind of dopant/host copolymer could be a promising candidate for blue‐light‐emitting polymers with high efficiency, good color purity, and excellent color stability.     

Heat‐Assisted Photoacidic Oxidation Method for Tailoring the Surface Chemistry of Polymer Dielectrics for Low‐Power Organic Soft Electronics

The use in low‐power soft electronics of the appropriate insulating polymer materials with a high dielectric constant (k) is considered a practical alternative to that of inorganic dielectric materials, which are brittle and have high processing temperatures. However, the polar surfaces of typical high‐k polymer insulators are problematic. Further, it is a huge challenge to control their surface properties without damage because of their soft and chemically fragile nature. Here, a heat‐assisted photoacidic oxidation method that can be used to effectively oxidize the outermost surfaces of high‐k rubbery polymer films without degradation is presented. The oxidized surfaces prepared with the developed method contain large numbers of hydroxyl groups that enable the subsequent growth of dense and ordered self‐assembled monolayers (SAMs) consisting of organosilanes. The whole process modifies the surface characteristics of polymer dielectrics effectively. The mechanisms of the oxidation of polymer surfaces and the subsequent SAM growth process are investigated. The resulting surface‐tailored rubbery dielectrics exhibit superior electrical characteristics when used in organic transistors. These results demonstrate that this method can be used to realize practical soft organic electronics based on high‐k polymer dielectrics.     

Amino N‐Oxide Functionalized Conjugated Polymers and their Amino‐Functionalized Precursors: New Cathode Interlayers for High‐Performance Optoelectronic Devices

A series of amino N‐oxide functionalized polyfluorene homopolymers and copolymers (PNOs) are synthesized by oxidizing their amino functionalized precursor polymers (PNs) with hydrogen peroxide. Excellent solubility in polar solvents and good electron injection from high work‐function metals make PNOs good candidates for interfacial modification of solution processed multilayer polymer light‐emitting diodes (PLEDs) and polymer solar cells (PSCs). Both PNOs and PNs are used as cathode interlayers in PLEDs and PSCs. It is found that the resulting devices show much better performance than devices based on a bare Al cathode. The effect of side chain and main chain variations on the device performance is investigated. PNOs/Al cathode devices exhibit better performance than PNs/Al cathode devices. Moreover, devices incorporating polymers with para‐linkage of pyridinyl moieties exhibit better performance than those using polymers with meta‐linked counterparts. With a poly[(2,7‐(9,9‐bis(6‐(N,N‐diethylamino)‐hexyl N‐oxide)fluorene))‐alt‐(2,5‐pyridinyl)] (PF6NO25Py) cathode interlayer, the resulting device exhibits a luminance efficiency of 16.9 cd A^?1 and a power conversion efficiency of 6.9% for PLEDs and PSCs, respectively. These results indicate that PNOs are promising new cathode interlayers for modifying a range of optoelectronic devices.     

Solvent‐Assisted Low‐Temperature Crystallization of SnO2 Electron‐Transfer Layer for High‐Efficiency Planar Perovskite Solar Cells

A high‐quality polycrystalline SnO₂ electron‐transfer layer is synthesized through an in situ, low‐temperature, and unique butanol–water solvent‐assisted process. By choosing a mixture of butanol and water as a solvent, the crystallinity is enhanced and the crystallization temperature is lowered to 130 °C, making the process fully compatible with flexible plastic substrates. The best solar cells fabricated using these layers achieve an efficiency of 20.52% (average 19.02%) which is among the best in the class of planar n–i–p‐type perovskite (MAPbI₃) solar cells. The strongly reduced crystallization temperature of the materials allows their use on a flexible substrate, with a resulting device efficiency of 18%.     

On‐Chip Super‐Resolution Imaging with Fluorescent Polymer Films

Wide field‐of‐view (FOV), label‐free, super‐resolution imaging is demonstrated using a specially designed waveguide chip that can illuminate a sample with multicolor evanescent waves travelling along different directions. The method is enabled by a polymer fluorescent film that emits over a broad wavelength range. Its polygonal geometry ensures coverage over all illumination directions, enabling high‐fidelity image reconstruction while minimizing distortion and image blurring. By frequency shifting and iterative stitching of different spatial frequencies in Fourier space, the reconstruction of 2D samples is achieved without distortion over wide FOVs. The fabrication process is facile and compatible with conventional semiconductor‐fabrication methods. The super‐resolution chip (SRC) can thus be produced with high yield, offering opportunities for potential conjunction of super‐resolution techniques integrated optical circuits or for the development of single‐use diagnostic kits.     

Acylhydrazones as Reversible Covalent Crosslinkers for Self‐Healing Polymers

The utilization of dynamic covalent and noncovalent bonds in polymeric materials offers the possibility to regenerate mechanical damage, inflicted on the material, and is therefore of great interest in the field of self‐healing materials. For the design of a new class of self‐healing materials, methacrylate containing copolymers with acylhydrazones as reversible covalent crosslinkers are utilized. The self‐healing polymer networks are obtained by a bulk polymerization of an acylhydrazone crosslinker and commercially available methacrylates as comonomers to fine‐tune the T_g of the systems. The influence of the amount of acylhydrazone crosslinker and the self‐healing behavior of the polymers is studied in detail. Furthermore, the basic healing mechanism and the corresponding mechanical properties are analyzed.     

Dual‐Functionalized Polymer Nanotubes as Substrates for Molecular‐Probe and DNA‐Carrier Applications

Bifunctionalized polymer nanotubes have been fabricated using vapor‐deposition polymerization in FeCl₃‐adsorbed anodic aluminum oxide membranes followed by attachment of amine‐functionalized silica nanoparticles. The prepared bifunctionalized polymer nanotubes are applied as both a molecular probe and a DNA carrier by conjugating pyreneacetic acid with the amine groups and immobilizing DNA with the carboxylic acid groups on the surface. The number of amine functional groups on the nanotubes' surface can be measured by means of the photoluminescence intensity of pyreneacetic acid conjugated with amine groups, and the number of the residual carboxylic acid groups is calculated by titration with sodium hydroxide. Fourier‐transform infrared spectroscopy, X‐ray photoelectron spectroscopy, transmission electron microscopy, scanning electron microscopy, and confocal laser scanning microscopy have been performed to confirm the complete polymerization of the monomer and the attachment of photoluminescent molecules and single‐stranded DNA.