啁啾光纤光栅补偿光纤色散的研究

啁啾光纤光栅被认为是目前最有实用价值的色散补偿方案之一。分析了啁啾光纤光栅补偿色散的基本原理,从简单模型出发分析了啁啾光纤光栅的色散补偿能力,用数值法研究了啁啾光纤光栅的时延及色散特性,并比较了变迹型与非变迹型啁啾光纤光栅。结果表明要获得较大的色散,要求光纤光栅有较长的长度和较小的啁啾。同时为了消除色散曲线的振荡还必须采取适当的变迹方法。     

线性啁啾光纤光栅变迹函数的研究

文中利用传输矩阵法对我们构造的四种变迹函数所描述的线性啁啾光纤光栅的光学特性进行了数值计算,并与常用的高斯型变迹线性啁啾光纤光栅的最佳光学特性进行了比较和分析,得出了一些有意义的结论,为设计和制作合适的线性啁啾光纤光栅用作色散补偿器提供了一定的理论依据。     

相位掩模板接缝相差对光栅时延纹波的影响

电子束刻蚀啁啾相位掩模板采用的是分步啁啾法,而掩模板制造过程中分步之间的接缝误差是啁啾光纤光栅产生时延纹波的一个重要因素。该文以分步步长1 mm,总长度140 mm的相位掩模板为例,理论分析和比较了不同接缝误差对啁啾光纤光栅时延纹波的影响。分析表明,最大相位误差为0.05 rad和0.08 rad时,光栅时延纹波的统计平均分别为14.491 ps和22.38 ps。进行相关试验研究以上相位掩模板写入光栅的时延特性,得出结论与理论分析一致。     

电子束刻蚀分步啁啾相位掩模板的优化

掩模板制造过程中采用的是分步啁啾方法,分步间长度容易出现误差,这种接缝误差是引起啁啾光纤光栅（CFBG）时延纹波的系统误差。理论分析了相位掩模板的接缝误差对CFBG时延纹波的影响。分析表明,对长度为140mm的掩模板采用1．4mm的步长,接缝误差影响最小。并进行了实验验证。     

利用啁啾光纤光栅实现10Gb/s WDM系统色散补偿

利用二次曝光法制作的啁啾光纤光栅在国内首次邮１０Ｇｂ／ｓｅ ＷＤＭ系统单路色散补偿,经１８０ｋｍ传输后色散补偿的功率代价为１ｄＢ。     

利用线性啁啾光纤光栅进行脉冲压缩的研究

利用光纤－线性啁啾光纤光栅进行光脉冲的压缩,首先讨论了线性啁啾光纤光栅的色散特性,并给出耦合系数为反高斯函数的线性啁啾光纤光栅的色散特性;然后利用此种光纤光栅与正常色散光纤结合进行光脉冲的压缩,通过理论和数值分析,得出一简单设计规则;最后利用此规划设计一个压缩因子为１０的光纤－线性啁啾光纤光栅压缩器。     

线性源啁啾对孤子脉冲压缩的影响

通过线性源啁啾对孤子脉冲压缩影响的研究,发现泵浦脉冲和孤子脉冲的源啁啾参量地脉冲压缩产生重要影响,且孤子脉冲压缩存在最佳光纤长度。在泵浦功率一定的条件下,选取负啁啾的泵浦脉冲正啁啾的孤子脉冲可以获得高压缩因子的光脉冲;同时选取负啁啾的泵浦脉冲和正啁啾的孤子脉冲易于产生更短的压缩光脉冲。     

Investigation on reflection spectr a of chirped and phase-shifted fiber Bragg gratings

The characteristics of chirped and phase-shifted fiber Bragg gratings have been investigated by the use of transfer matrix formulation. While the characteristics of a chirped and phase-shifted fiber Bragg grating are the same as those of non- chirped one in some important aspects, both the reflection and transmission windows of a chirped and phase-shifted fiber Bragg grating can be broadened in a wide range. Therefore, chirped and phase-shifted fiber Bragg gratings will have applications in WDM or DWDM optical communication systems. The work in this paper can be used to design the new devices based on chirped and phase-shifted fiber Bragg gratings.     

利用梯度曲率梁实现光纤光栅啁啾化

提出了一种新颖的利用梯度曲率梁将光纤光栅调制成啁啾光栅的方法,给出了设计方法,并从理论上进行了分析.实验中获得了5.10 nm的啁啾带宽,而且中心波长不变.     

啁啾光纤光栅色散补偿变迹函数的研究

本文理论地研究了啁啾光纤光栅色散补偿迹耦合函数,将两个耦合方程推导一个Ｒｉｃｃａｔｉ微分方程然后通过Ｒｕｎｇｅ－Ｋｕｔｔａ法求解在不同耦合函数下啁啾光纤光栅的反射,色散和群时延,系统地讨论了和比较了两种合函数下的啁光纤光栅补偿性能。     

Calculation of the Figure of Merit of Linearly Chirped Fiber Gratings for Dispersion Compensation

1IntroductionBecauseoftheadventoferbium-dopedamplifiers,thelengthoftheophcalfiberlinksisnolongerlicitedbytheabsorphon,butratherbythechromaticdispersionofthefiber.Especially'theophcalsignalshapeissoseriouslydestroyedthatthebit-error-rate(BER)isratherhigherinthelonghaulhigh-bit-rateophcalcommunicationsystem.Sothedispersionoffibermustbecompensatedbyvariouskindsofdevices.Amongthem,thecompensatorusingthelinearlychirpedfibergratingshascausedagreatinterestindispersioncompensatingdeVices11-5].Onemus…     

啁啾光栅解调的准分布式光纤Bragg光栅传感器

为了提高光纤Bragg光栅(FBG)的应用范围.提出一种线性啁啾光栅(CFBG)解调的准分布式FBG传感系统.利用波导理论分析了CFBG特性;利用传输矩阵法推导了CFBG反射谱模型及波长与相位延迟的关系,并给出了相位延迟曲线.实验表明:所设计的系统应变测量范围为0～2000 με,温度测最范围为0～80℃;相位变化与被...     

线性啁啾光纤布喇格光栅反射谱的数值模拟

为了研究线性啁啾光纤布喇格光栅的特性,并进一步把它用于光纤激光器上,介绍了线性啁啾光纤布喇格光栅的耦合模理论,采用4阶Runge-Kutta法和传输矩阵法结合控制变量法,对线性啁啾光纤布喇格光栅反射率与啁啾系数、半峰全宽与光栅长度、反射率与直流纤芯折射率改变量之间的关系进行了数值模拟。结果表明,线性啁啾光纤布喇格光纤可以展宽带宽。基于这个结论,提出了利用线性啁啾光纤布喇格光栅作为光纤激光器腔镜,使输出谱线展宽,从而可作为宽带光源使用的方案。     

平方型啁啾光纤光栅高阶色散补偿器的理论设计

对周期保持恒定,而其有效折射率大小随其长度按平方律变化的啁啾光 纤光栅提出了一个理论设计模型,从该模型出发,得到了光栅有效折射率分布函数与光栅色散量之间的关系,最后将该模型的计算结果与传输矩阵法的计算机模拟结果进行了比较,二者基本上一致。     

Dual-Wavelength DFB Fiber Laser Based on a Chirped Structure and the Equivalent Phase Shift Method

A chirped phase-shifted structure is demonstrated for compact multiwavelength distributed feedback (DFB) fiber laser at room temperature for the first time. The chirped structure provides separated resonance cavities and then the stable multiwavelength operation. The equivalent phase shift method is demonstrated to realize the desired chirp and phase shifts simply and flexibly. A 44-pm-spaced dual-wavelength DFB fiber laser is then achieved experimentally, which is the narrowest spacing ever reported for a compact multiwavelength fiber laser.     

色散管理光纤锁模激光器在近零色散域的非线性优化

目前,飞秒激光脉冲因脉冲宽度窄和峰值功率高的特点被广泛运用在多种领域中。其中,色散管理光纤锁模激光器因其特有的腔内呼吸机制使输出的激光脉冲能量更高,光谱更宽、脉宽更窄。使用啁啾布拉格光纤光栅进行色散管理的光纤锁模激光器能够实现真正的全光纤结构,提升激光器的紧凑性和稳定性,因此基于啁啾布拉格光纤光栅进行色散管理的光纤锁模激光器具有更加实际的应用意义。采用数值模拟的方法,研究了基于啁啾布拉格光纤光栅进行色散管理的掺镱光纤锁模激光器中单模光纤在腔内的不同分布对脉冲动力学过程和输出脉冲参数的影响。系统分析了谐振腔内净色散值不同时,腔内单模光纤的分布对脉冲在腔内的动力学过程的影响。模拟结果表明,在腔内净色散值为负时,啁啾布拉格光纤光栅与增益光纤间的单模光纤越短,光纤激光器维持稳定单脉冲运行的最大泵浦强度更高且输出光谱更宽,从而能够获得脉宽更窄的去啁啾脉冲;腔内净色散值越接近零时,啁啾布拉格光纤光栅与增益光纤间的单模光纤长度对输出脉冲参数作用的影响越显著;腔内净色散值为正时,单模光纤在腔内的分布对输出脉冲影响逐渐减弱,优化单模光纤分布提升锁模激光器性能并不明显。最后,提出了一种通过改变单模光纤在腔内的分布来提高激光器输出性能的优化方法。     

Group delay ripple reduction and reflectivity increase in a chirpedfiber Bragg grating by multiple-overwriting of a phase mask with anelectron-beam

The phase errors in electron-beam-written step-chirped masks can be reduced by using a method based on the continuous movement approach and overwriting a pattern at the same place on the substrate several times. The group delay ripple of chirped fiber Bragg gratings fabricated by a four-times-overwritten phase mask is comparable with that of gratings obtained using a holographically written chirped phase mask     

线性啁啾对布拉格光纤光栅反射谱的影响

以耦合模理论为基础,采用分段均匀和传输矩阵法,得到分析啁啾非均匀光纤光栅光谱特性教学物理模型,讨论了啁啾系数对高斯型切趾光栅和相移光栅滤波特性的影响。     

二类取样NLCFG的多波长色散补偿特性

根据非线性啁啾光纤光栅可用于对光通信系统中一阶和二阶色散进行补偿的原理 ,系统地研究了二类取样型非线性啁啾光纤光栅的反射谱及时延特性 ,并进行了数值仿真。提出了计算二类取样光栅产生的信道数的计算方法。     

Continuous True-Time-Delay System Employing a Novel Tunable Chirped Fiber Grating Delay Line and a Sampled Grating Based Multiwavelength Fiber Laser

A photonics true-time-delay system for phased array antenna beam steering employing a novel tunable chirped fiber grating delay line and a multi-wavelength erbium-doped fiber ring laser source based on a sampled grating filter is proposed. The tunable chirped fiber grating, which act as a continuous time-delay element, is achieved by bending a uniform fiber Bragg grating bonded at a slant onto the lateral surface of a simply supported beam. This technique allows the dynamic control of the chirp rate and spectral width of the grating without center wavelength shift. By adjusting the chirp rate of the fiber grating via bend strain, this kind of tunable chirped fiber grating could achieve very low and adjustable delay times, therefore provides higher angle resolution for scanning microwave beam, even the wavelengths of laser source are fixed and un-tunable. The true-time-delay system using proposed tunable chirped fiber grating delay element and sampled grating based laser source is constructed and demonstrated experimentally.