Microstructure and XRD analysis of FSW joints for copper T2/aluminium 5A06 dissimilar materials

Copper (T2) and aluminium alloy (5A06) were welded by friction stir welding (FSW). The microstructure, mechanical properties and phase constituents of FSW joints were studied by metallography, tensile testing machine and X-ray diffraction. The results indicated that the high quality weld joint could be obtained when tool rotational speed is 950 rpm, and travel speed is 150 mm/min. The maximum value of tensile strength is about 296 MPa. The metal Cu and Al close to copper side in the weld nugget (WN) zone showed a lamellar alternating structure characteristic. However, a mixed structure characteristic of Cu and Al existed in the aluminium side of weld nugget (WN) zone. There were no new Cu-Al intermetallic compounds in the weld nugget zone.     

Lap joint properties of FSWed dissimilar formed 5052 Al and 6061 Al alloys with different thickness

Lap joint friction stir welding (FSW) between dissimilar 5052-H112 (1 mm) and 6061-T6 (2 mm) Al alloys with different thickness was carried out with various tool rotation speeds and welding speeds according to the fixed location of each material on bottom or top sheet. Interface morphology was characterized by pull-up or pull-down from initial joint line. Amount of vertical material transports increased and thickness of 5052 resultantly lessened with increasing tool rotation and decreasing welding speed, which were the conditions of the weak bond. Higher stress concentration on the interface pull-up region, the penetration of unbonded region into the weld zone and the lessened thickness of 5052 Al part might be the reasons for lower fracture load. Higher fracture load was acquired at the lower tool rotation speed and higher welding speed when a thicker 6061 was fixed at retreating side on top sheet. Interface morphology was the most important factor determining the mechanical strength of lap FSW joints and can be manageable using FSW parameters.     

Investigations on the effects of friction stir welding parameters on intermetallic and defect formation in joining aluminum alloy to mild steel

Joints of Al 5186 to mild steel were performed by using friction stir welding (FSW) technique. The effects of various FSW parameters such as tool traverse speed, plunge depth, tilt angle and tool pin geometry on the formation of intermetallic compounds (IMCs), tunnel formation and tensile strength of joints were investigated. At low welding speeds due to the formation of thick IMCs (which was characterized as Al₆Fe and Al₅Fe₂) in the weld zone the tensile strength of joints was very poor. Even at low welding speeds the tunnel defect was formed. As the welding speed increased, the IMCs decreased and the joint exhibited higher tensile strength. The tunnel defect could not be avoided by using cylindrical 4 mm and 3 mm pin diameter. By using a standard threaded M3 tool pin the tunnel was avoided and a bell shape nugget formed. Therefore tensile strength of the joint increased to 90% of aluminum base alloy strength. At higher welding speed and lower tool plunge depth, the joint strength decreased due to lack of bonding between aluminum and steel. Based on the findings, a FSW window has been developed and presented.     

铝/钢异种材料搅拌摩擦焊研究进展

由于铝、钢的物理化学性质存在巨大差异,铝/钢的连接是焊接领域的难点问题。搅拌摩擦焊是低热输入的固态连接方法,能够有效控制铝/钢金属间化合物的生长,且搅拌针强烈的搅拌作用可增加铝/钢异种材料机械咬合程度,得到高质量的铝/钢焊接接头,铝/钢搅拌摩擦焊已经成为了焊接领域的热点问题。文中综述了铝/钢搅拌摩擦焊国内外研究现状,涉及到接头形式、焊缝成形、焊接工艺和力学性能,着重介绍了铝/钢搅拌摩擦焊接头的连接机制,并围绕铝/钢搅拌摩擦焊存在的两大问题,对铝/钢搅拌摩擦焊新技术进行总结,并进一步提出了铝/钢搅拌摩擦焊的基础研究方向。     

Investigation on dissimilar underwater friction stir lap welding of 6061-T6 aluminum alloy to pure copper

Friction stir welding (classical FSW) is considered to offer advantages over the traditional fusion welding techniques in terms of dissimilar welding. However, some challenges still exist in the dissimilar friction stir lap welding of the aluminum/copper (Al/Cu) metallic couple, among which the formation of the Al–Cu intermetallic compounds is the major problem. In the present research, due to the fact that the formation and growth of the intermetallic are significantly controlled by the thermal history, the underwater friction stir welding (underwater FSW) was employed for fabricating the weld, and the weld obtained by underwater FSW (underwater weld) was analyzed via comparing with the weld obtained under same parameters by classical FSW (classical weld). In order to investigate the effect of the external water on the thermal history, the K-type thermocouple was utilized to measure the weld temperature, and it is found that the water could decrease the peak temperature and shorten the thermal cycle time. The XRD results illustrate that the interface of the welds mainly consist of the Al–Cu intermetallic compounds such as CuAl₂ and Cu₉Al₄ together with some amounts of Al and Cu, and it is also found that the amount of the intermetallic in the underwater weld is obvious less than in the classical weld. The SEM images and the EDS line scan results also illustrate that the Al–Cu diffusion interlayer at the Al–Cu interface of the underwater weld was obviously thinner than that of the classical weld.     

铝 / 镁异种金属搅拌摩擦焊研究现状及发展趋势

为进一步优化焊接工艺,提高铝/镁异种金属搅拌摩擦焊接头的性能,促进铝/镁异种金属结构在航空航天、轨道交通、汽车工业等领域的广泛应用,综述了近5年来国内外铝/镁异种金属搅拌摩擦焊接的最新研究成果,对焊接工艺参数、接头的力学性能、微观组织以及异种金属搅拌摩擦焊的新工艺进行了总结和分析。国内外大量研究结果表明,通过选择合适的工艺参数、改变搅拌针的偏移,可以获得抗拉强度较高、焊缝成形良好的铝/镁异种金属搅拌摩擦焊接头,焊缝中存在的金属间化合物是导致焊接接头性能不能满足工程应用的主要因素,但目前对于搅拌摩擦焊接过程中金属间化合物的产生、分布规律缺乏深入研究。     

Microstructure and interface characterization of dissimilar friction stir welded lap joints between Ti–6Al–4V and AISI 304

The feasibility of dissimilar friction stir welding (FSW) in overlap configuration between Ti–6Al–4V alloy (Ti64) and AISI 304 austenitic stainless steels (304SS) was investigated. Sound joints were achieved when placing titanium as the upper workpiece. Joints were successfully produced by employing a welding speed of 1 mm/s and rotational speeds of 300 and 500 rpm. A lamellar microstructure was formed in the stir zone of Ti64, where grain size was found to increase with increasing rotational speed, and austenitic equiaxed grains were obtained near the interface of 304SS coupon. Energy dispersive X-ray spectroscopy (SEM-EDS) of the interface revealed a thin intermixed region and suggested intermetallic compound formation. Microhardness data in the titanium weld zone for both rotational speeds exhibited slightly lower values than the base material, with the lowest values in the heat affected zone, whereas the microhardness values in the stainless steel side around the weld center were found to be higher than those obtained for the base material.     

Material stirring during FSW of Al–Cu: Effect of pin profile

Friction stir welding (FSW) joins the material in solid state, and it gets evolved as a new and effective technique to join dissimilar materials such as aluminum and copper. FSW tool design and configuration critically affect the joint quality. This study has evaluated the effect of different pin profiles used during FSW of AA5754 Al alloy and commercially pure copper in a butt configuration on the microstructure, material movement, and microhardness for the different joints. The joining is performed through the different pin profiles of cylindrical, taper, cylindrical cam, taper cam, and square shape at the rotational and welding speed of 900?rpm and 40?mm/min respectively. Among all joints, the square pin profile provides good joining and microhardness. Square tool pin profile facilitates good amount of mixing at nugget zone, which consequently increases the hardness. The material movement in square tool pin profile joint is also studied on the longitudinal plane to understand the effect of pulsating and stirring action on the material mixing pattern in dissimilar FSW. It is evident that the softer material in the stir zone gets more stirring, and the flow lines are clearly visible for the stirred material.     

Effect of tool rotational speed and pin profile on microstructure and tensile strength of dissimilar friction stir welded AA5083-H111 and AA6351-T6 aluminum alloys

The relatively new welding process friction stir welding (FSW) was applied in this research work to join 6 mm thick dissimilar aluminum alloys AA5083-H111 and AA6351-T6. The effect of tool rotational speed and pin profile on the microstructure and tensile strength of the joints were studied. Dissimilar joints were made using three different tool rotational speeds of 600 rpm, 950 rpm and 1300 rpm and five different tool pin profiles of straight square (SS), straight hexagon (SH), straight octagon (SO), tapered square (TS), and tapered octagon (TO). Three different regions namely unmixed region, mechanically mixed region and mixed flow region were observed in the weld zone. The tool rotational speed and pin profile considerably influenced the microstructure and tensile strength of the joints. The joint which was fabricated using tool rotational speed of 950 rpm and straight square pin profile yielded highest tensile strength of 273 MPa. The two process parameters affected the joint strength due to variations in material flow behavior, loss of cold work in the HAZ of AA5083 side, dissolution and over aging of precipitates of AA6351 side and formation of macroscopic defects in the weld zone.     

焊接速度对 7A52 铝合金 FSW 组织及力学性能的影响

目的在保证搅拌速度一定时,针对8 mm厚的7A52铝合金,在不同焊接速度下采用搅拌摩擦焊(FSW)进行焊接试验,研究其焊接接头的显微组织及力学性能。方法利用搅拌摩擦焊机进行对接焊接,焊后制取金相试样观察焊接接头宏观形貌和显微组织,并测定其力学性能。结果7A52铝合金FSW焊接接头焊核区的面积随着焊接速度的增大而增大,当焊接速度为250mm/min时,焊接接头的焊核区面积最大,焊核区的显微组织都为细小的等轴晶,焊接接头横截面的焊核区呈明显"洋葱环"的形貌,而热力影响区的结构特征则呈现出了较高的塑性变形流线层。焊接接头显微硬度分布都呈现出"W"形变化,在焊接速度为150 mm/min时,焊接接头的平均抗拉强度能达到452 MPa,达到了母材抗拉强度的89%。结论通过对不同焊接速度下7A52铝合金FSW焊接接头的组织和性能进行研究,得到了不同焊接速度下焊接接头组织和力学性能。     

水下搅拌摩擦焊对铝/铜接头组织与性能的影响

目的 采用搅拌摩擦焊,对比分析大气环境和水下环境下铝/铜接头的组织与性能,以期获得力学性能更优异的铝/铜焊接接头。方法 利用搅拌摩擦焊,在焊接速度为40 mm/min、旋转速度为1 000 r/min的条件下,分别在大气环境和水下环境下对厚度为9 mm的6061铝合金板和T2纯铜板进行焊接。然后,对铝/铜界面、焊核区进行扫描电镜及能谱分析,并对铝/铜界面及焊核区进行物相分析,确定产物相组成。最后,对铝/铜试样进行拉伸及硬度检测。结果 铝/铜接头均无裂纹、气孔等缺陷。铜颗粒弥散分布在焊核区,铝/铜界面形成金属间化合物层。水下搅拌摩擦焊下界面元素扩散距离明显变短,且金属间化合物厚度更薄。铝/铜接头的金属间化合物为AlCu和Al4Cu9。大气环境焊接下接头的抗拉强度为130.6 MPa,断裂方式为脆性断裂;水下焊接下接头的抗拉强度为199.5 MPa,断裂方式为韧性断裂。水下环境下的接头硬度值更高,其中热影响区的硬度最低值约为65HV。结论 水下搅拌摩擦焊铝/铜接头无裂纹、气孔等缺陷。组织上,水下搅拌摩擦焊的铝/铜接头界面元素扩散距离更短,硬脆的金属间化合物更少;性能上,水下搅拌摩擦焊的铝/铜接头强度更高,抗拉强度达到199.5 MPa,达到母材的74.4%。     

Process parameters/material location affecting hooking in friction stir lap welding: Dissimilar aluminum alloys

Influence of spindle and weld speeds, metal location, direction of spindle rotation, and tool pin length on hooking in lap FSW of dissimilar aluminum alloys and the effect of hook on tensile and fatigue weld strength was studied. Optical images of the cross-section of the specimen welded at different process parameters were analyzed. The results indicate that increased spindle speed, reduced weld speed, higher tool pin length, clockwise spindle rotation, and locating the stronger material at the bottom of the joint increased the size of the hooking defect. Higher weld speeds and very high spindle speeds resulted in lower hook size on the advancing side (AS) compared to the retreating side (RS) of the joint. Welding with low weld speed would result in higher advancing side hook size compared to the retreating side. Friction stir weld joints fabricated with anti-clockwise spindle rotation has been found to have extremely low hook both on the AS and the RS of the joint. The tensile and fatigue strengths of the weld joints and plates are degraded by the hook. The fatigue strength of welded alloys could be improved by a double pass weld, the second pass welded immediately adjacent to the first pass.     

Friction Stir Welding of Al Alloy Thin Plate by Rotational Tool without Pin

For friction stir welding (FSW), a new idea is put forward in this paper to weld the thin plate of Al alloy by using the rotational tool without pin. The experiments of FSW are carried out by using the tools with inner-concave-flute shoulder, concentric-circles-flute shoulder and three-spiral-flute shoulder, respectively. The experimental results show that the grain size in weld nugget zone attained by the tool with three-spiral-flute shoulder is nearly the same while the grain sizes decrease with the decrease of welding velocity. The displacement of material flow in the heat-mechanical affected zone by the tool with three-spiral-flute shoulder is much larger than that by the tool with inner-concave-flute shoulder or concentric-circles-flute shoulder. The above-mentioned results are verified by numerical simulation. For the tool with three-spiral-flute shoulder, the tensile strength of FSW joint increases with the decrease of welding velocity while the value of tensile strength attained by the welding velocity of 20 mm/min and the rotation speed of 1800 r/min is about 398 MPa, which is 80% more than that of parent mental tensile strength. Those verify that the tool with three-spiral-flute shoulder can be used to join the thin plate of Al alloy.     

A Review on Dissimilar Friction Stir Welding of Copper to Aluminum: Process,Properties, and Variants

Copper and aluminum materials are extensively used in different industries because of its great conductivities and corrosion resistant nature. It is important to join dissimilar materials such as copper and aluminum to permit maximum use of the special properties of both the materials. The joining of dissimilar materials is one of the most advanced topics, which researchers have found from last few years. Friction stir welding (FSW) technology is feasible to join dissimilar materials because of its solid state nature. Present article provides a comprehensive insight on dissimilar copper to aluminum materials joined by FSW technology. FSW parameters such as tool design, tool pin offset, rotational speed, welding speed, tool tilt angle, and position of workpiece material in fixture for dissimilar Cu–Al system are summarized in the present review article. Additionally, welding defects, microstructure, and intermetallic compound generation for Cu–Al FSW system have been also discussed in this article. Furthermore, the new developments and future scope of dissimilar Cu–Al FSW system have been addressed.     

Identification of the pin offset effect on the friction stir welding (FSW) via Taguchi – Grey relational analysis: A Case study for AA 7075 – AA 6013 alloys

The aim of this work is to present a case study relating to the dissimilar friction stir welding (FSW) ability of AA 7075‐T651 and AA 6013‐T6 by applying pin offset technique. An orthogonal array L18 was conducted to perform the overlapped weld seams using three different values of pin offset, welding speed and tool rotational speed along with two different pin profiles determine the impact of welding parameters on the tensile properties of friction stir welded joints. The nugget zone for each of overlapped weld seams exhibited a complex structure and also, the pin offset and profile also were found to have a great impact on the microstructural evolution of the nugget zone. The ultimate tensile strength, elongation at the rapture and bending strength of welded joints were measured in the ranges of 194–215 MPa, 1.79–3.34 % and 203–352 MPa. From the Taguchi based Grey relational analysis, the optimum welding condition was determined for the welded joint performed using a single fluted pin profile with the zero pin offset, tool rotational speed of 630 min^?1 and welding speed of 63 mm/min. Microstructural and macro‐structural observations revealed that welded joints exhibiting lower tensile strength are consistent of various types of defects (e. g. cracks, tunnels and cavities). The fracture location of welded joints was found to be on the heat affected zone and between the heat affected zone and AA 6013‐base metal. The tool and pin wear was not observed during the welding applications     

On the effect of tool offset in hybrid-FSW of copper-aluminium alloy

Tool offset is one the most significant parameters in joining of dissimilar materials by friction stir welding (FSW) process. An investigation is carried out on the effect of tool offset toward thermal history, material flow pattern, mechanical properties, welding force, and weld joint morphology. It was found that offsetting toward aluminum side along with a plasma-assisted heat source is an efficient approach to address one of the most important apprehensions in aluminum-copper solid-state welding process. The offset influences the amount of intermetallic at the joint interface and in-effect impacts on final strength and material flow behavior. The optimum and continuous layer of intermetallic produces the maximum weld joint strength. The specimen welded with optimum tool offset shows the highest strength using 55 A plasma current in hybrid friction stir welding process.     

Effect of Process Parameters on Tensile Strength of Friction Stir Welded Cast LM6 Aluminium Alloy Joints

This paper reports the effect of friction stir welding(FSW)process parameters on tensile strength of cast LM6 aluminium alloy.Joints were made by using dierent combinations of tool rotation speed,welding speed and axial force each at four levels.The quality of weld zone was investigated using macrostructure and microstructure analysis.Tensile strength of the joints were evaluated and correlated with the weld zone hardness and microstructure.The joint fabricated using a rotational speed of 900 r/min,a weldin...     

Microstructure and tensile strength of friction stir welded joints between interstitial free steel and commercially pure aluminium

In the present study, the joining of interstitial free steel and commercial pure aluminium was carried out by friction stir welding (FSW) technique using tool rotational speeds of 600, 900, 1200 rpm and traverse speed of 100 mm/min. The microstructure and micro-hardness of the weld interface have been investigated. Optical microscopy was used to characterize the microstructures of different regions of friction stir welding joints. The scanning electron microscopy-back scattered electron (SEM-BSE) images show the existence of the different reaction layers in the welded zone. The Al₃Fe intermetallic compound has been observed in the weld interface and their thickness increase with the increase in tool rotational speed. Tensile strength was also evaluated and maximum tensile strength of ∼123.2 MPa along with ∼4.5% elongation at fracture of the joint have been obtained when processed at 600 rpm tool rotational speed.     

Dual-Rotation Speed Friction Stir Welding: Experimentation and Modeling

Implementing differential rotation speeds of pin and shoulder in the friction stir welding process is considered. Experimental investigations were carried out using a newly designed and fabricated apparatus for dual-rotation speed friction stir welding. Metallographic studies demonstrated that appropriate selection of separate pin and the shoulder rotation speeds not only results in defect-free joints, but also affects the weld zone by controlling the heat input delivered. An energy model for predicting maximum temperature was extended to the dual-rotation speed friction stir process. The model was verified using the previous experimental results reported in the literature.     

Effect of welding parameters on microstructure and mechanical properties of friction stir welded joints of AA7039 aluminum alloy

A high strength Al–Zn–Mg alloy AA7039 was friction stir welded by varying welding and rotary speed of the tool in order to investigate the effect of varying welding parameters on microstructure and mechanical properties. The friction stir welding (FSW) process parameters have great influence on heat input per unit length of weld, hence on temperature profile which in turn governs the microstructure and mechanical properties of welded joints. There exits an optimum combination of welding and rotary speed to produce a sound and defect free joint with microstructure that yields maximum mechanical properties. The mechanical properties increase with decreasing welding speed/ increasing rotary speed i.e. with increasing heat input per unit length of welded joint. The high heat input joints fractured from heat affected zone (HAZ) adjacent to thermo-mechanically affected zone (TMAZ) on advancing side while low heat input joints fractured from weld nugget along zigzag line on advancing side.