A novel proton conducting Ba0.95K0.05Ce0.6Zr0.2Gd0.16Zn0.04O3−δ for SOFC

A new proton conducting Ba_0.95K_0.05Ce_0.6Zr_0.2Gd_0.16Zn_0.04O_3−δ electrolyte membrane was prepared on NiO-based anode support by suspension spray followed by a co-sintering at 1400 °C for 4 h. Chemical stability test shows that this new proton conductor displays adequate chemical stability against CO₂ at intermediate temperatures. The conductivity of Ba_0.95K_0.05Ce_0.6Zr_0.2Gd_0.16Zn_0.04O_3−δ in humidified H₂ is about 50% higher than that of BaCe_0.6Zr_0.2Gd_0.16Zn_0.04O_3−δ from 500 to 800 °C. With La_0.8Sr_0.2MnO_3−δ cathode, fuel cell with Ba_0.95K_0.05Ce_0.6Zr_0.2Gd_0.16Zn_0.04O_3−δ electrolyte shows 1.02 V of OCV and 354 mW/cm² of maximum power density at 700 °C, respectively. And the cell performance did not degrade after running at least for 10 h.     

Composition-controlled synthesis, structure and magnetic properties of ternary FexCoyNi100−x−y alloys attached on carbon nanotubes

Fe_xCo_yNi_100−x−y alloy nanoparticles with controllable compositions attached on the surface of carbon nanotubes (CNTs) were synthesized using an easy two-step route including adsorption and reduction processes. The nanocomposites have been characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), energy-disperse X-ray spectroscopy (EDS) and vibrating sample magnetometer (VSM). The effect of the alloy composition on microstructure and magnetic properties of ternary FeCoNi alloys attached on carbon nanotubes have been studied. During the nominal composition range (x = 21, 24, 33, 37, 46 and y = 60, 46, 48, 48, 35), Fe_xCo_yNi_100−x−y alloy nanoparticles attached on CNTs are quasi-spherical, fcc–bcc dual phase, and the coercivity (H_c) and saturation magnetization (M_s) vary with the alloy composition. The H_c of Fe_xCo_yNi_100−x−y alloy nanoparticles attached on CNTs decreases and M_s increases with increasing Fe content. These demonstrate that the two-step route is promising for fabricating alloy nanoparticles attached on CNTs for magnetic storage and ultra high-density magnetic recording applications.     

Morphology, optical and magnetic properties of Zn1−xNixO nanorod arrays fabricated by hydrothermal method

Zn_1−xNi_xO (x = 0, 0.05, and 0.1) nanorod arrays were prepared by hydrothermal method. Morphology and structure analysis indicate that the nanorods have single-crystalline wurtzite structure, and no metallic Ni or NiO phase exists. Room temperature ferromagnetism (RTFM) was observed in the Zn_0.9Ni_0.1O nanorods. In addtion, photoluminescence spectra of Zn_1−xNi_xO (x = 0, 0.05, 0.1 and 0.2) samples exhibit near band edge UV emissions and orange-red emissions. And the orange-red emission is confirmed to have originated from the interstitial oxygen defects.     

Investigation of the microwave dielectric properties of Ca1−xMgxLa4Ti5O17 ceramics for application in coplanar patch antenna

In this paper, the dielectric properties of Ca_1−xMg_xLa₄Ti₅O₁₇ ceramics at microwave frequency have been studied. The diffraction peaks of Ca_(1−x)Mg_xLa₄Ti₅O₁₇ ceramics nearly unchanged with x increasing from 0 to 0.03. Similar X-ray diffraction peaks of Ca_0.99Mg_0.01La₄Ti₅O₁₇ ceramic were observed at different sintering temperatures. A maximum density of 5.3 g/cm³ can be obtained for Ca_0.99Mg_0.01La₄Ti₅O₁₇ ceramic sintered at 1500 °C for 4 h. A maximum dielectric constant (_r) and quality factor (Q × f) of Ca_0.99Mg_0.01La₄Ti₅O₁₇ ceramic sintered at 1500 °C for 4 h are 56.3 and 12,300 GHz (at 6.4 GHz), respectively. A near-zero temperature coefficient of resonant frequency (τ_f) of −9.6 ppm/°C can be obtained for Ca_0.99Mg_0.01La₄Ti₅O₁₇ ceramic sintered at 1500 °C for 4 h. The measurement results for the aperture-coupled coplanar patch antenna at 2.5 GHz are presented. With this technique, a 3.33% bandwidth (return loss <−10 dB) with a center frequency at approximately 2.5 GHz has been successfully achieved.     

Thermoelectric properties of novel skutterudites with didymium: DDy(Fe1−xCox)4Sb12 and DDy(Fe1−xNix)4Sb12

In order to improve the thermoelectric properties via efficient phonon scattering Didymium (DD), a mixture of Pr and Nd, was used as a new filler in ternary skutterudites (Fe_1−xCo_x)₄Sb₁₂ and (Fe_1−xNi_x)₄Sb₁₂. DD-filling levels have been determined from combined data of X-ray powder diffraction and electron microprobe analyses (EMPA). Thermoelectric properties have been characterized by measurements of electrical resistivity, thermopower and thermal conductivity in the temperature range from 4.3 to 800 K. The effect of nanostructuring in DD_0.4Fe₂Co₂Sb₁₂ was elucidated from a comparison of both micro-powder (ground in a WC-mortar, 10 μm) and nano-powder (ball-milled, 150 nm), both hot pressed under identical conditions. The figure of merit ZT depends on the Fe/Co and Ni/Co-contents, respectively, reaching ZT > 1. At low temperatures the nanostructured material exhibits a higher thermoelectric figure of merit. The Vickers hardness was measured for all samples being higher for the nanostructured material.     

Fabrication and performance of La0.8Sr0.2MnO3/YSZ graded composite cathodes for SOFC

The performance of multi-layer (1 − x) La_0.8Sr_0.2MnO₃/x YSZ graded composite cathodes was studied as electrode materials for intermediate solid oxide fuel cells (SOFC). The thermal expansion coefficient, electrical conductivity, and electrochemical performance of multi-layer composite cathodes were investigated. The thermal expansion coefficient and electrical conductivity decreased with the increase in YSZ content. The (1 -x)La_0.8Sr_0.2MnO₃/x YSZ composite cathode greatly increased the length of the active triple phase boundary line (TPBL) among electrode, electrolyte, and gas phase, leading to a decrease in polarization resistance and an increase in polarization current density. The polarization current density of the triple-layer graded composite cathode (0.77 A/cm²) was the highest and that of the monolayer cathode (0.13 A/cm²) was the lowest. The polarization resistance (R_p) of the triple-layer graded composite cathode was only 0.182 ω·cm² and that of the monolayer composite cathode was 0.323 ω·cm². The power density of the triple-layer graded composite cathode was the highest and that of the monolayer composite cathode was the lowest. The triple-layer graded composite cathode had superior performance.     

Magnetic properties of (Fe)1−x–(Al2O3)x and (Fe50Ni50)1−x–(Al2O3)x nanocomposite magnetic media synthesized using gel like Al2O3 matrix

Composites with ferromagnetic nanoparticles, Fe and Fe₅₀Ni₅₀, dispersed in Al₂O₃ have been synthesized by a solution phase technique. The structure and magnetic properties of these composites with varying fractions of Al₂O₃ have been investigated. Both Fe and Fe₅₀Ni₅₀ nanoparticles are amorphous in the as-prepared state and become crystalline on heat treating with near equilibrium lattice parameters of 0.287 nm and 0.358 nm respectively. The interparticle distance increases with increasing Al₂O₃ from 0 wt.% to 20 wt.%. The size of Fe nanoparticles is 40 nm while the Fe₅₀Ni₅₀ nanoparticles are 20 nm in size. The Fe and Fe₅₀Ni₅₀ nanoparticles dispersed composites are found to be ferromagnetic at room temperature both in the as-prepared and heat treated conditions with clear coercive fields of 5.5–35 × 10³ A m⁻¹. The saturation magnetization increases by orders of magnitude on heat treatment, for e.g. from <1.0 emu g⁻¹ to 143.4 emu g⁻¹ for Fe–15 wt.% Al₂O₃ and 95.6 emu g⁻¹ for Fe₅₀Ni₅₀–15 wt.% Al₂O₃. The Fe-composites exhibit a Curie transition at 1000 K while the Fe₅₀Ni₅₀ composites exhibit a transition at 880 K, both temperatures close to bulk values.     

Studies on structural and electrical properties of Co1−xNixFe1.9Mn0.1O4 ferrite

Nickel-doped iron-deficient cobalt ferrite with small amount of manganese having the chemical composition Co_1−xNi_xFe_1.9Mn_0.1O₄, with x = 0.2, 0.4, 0.6 and 0.8, were prepared by standard double sintering ceramic method. The spinel phase formation was confirmed by X-ray diffraction (XRD). The DC resistivity measurements with temperature indicate a semiconducting behavior showing a linear decrease with increasing temperature and the doping of Ni enhances the resistivity. Maximum resistivity of the order of 10⁹ Ω cm was found for composition x = 0.8. Room temperature dielectric constant measurements with frequency (100 Hz to 1 MHz), show usual dielectric dispersion. Also, the variation of room temperature AC conductivity as a function of frequency were studied and explained by using Maxwell–Wagner two-layer model. The studies on dielectric constant (′), loss tangent (tan δ) and AC conductivity (σ_AC), at four different frequencies (viz., 1, 10, 100 kHz and 1 MHz), with temperature were made.     

Formation and properties of the Zr75−xAlxNi10Cu10Ti5 bulk metallic glasses

Zr-based bulk metallic glasses (BMGs) exhibit interesting mechanical properties since they combine high fracture stress, elastic strain (up to 2%), significant fracture toughness and good corrosion resistance. Quaternary systems with general composition Zr–Ni–Cu–Ti show wide composition ranges in which BMG can be obtained. The addition of the another element to the quaternary alloys often increases the glass forming ability (GFA). The aim of this work was to study the influence of aluminium content on the GFA and on the mechanical properties of the Zr–Ni–Cu–Ti alloys. Multicomponent Zr_75−xAl_xNi₁₀Cu₁₀Ti₅ (x = 15, 20 at%) alloys were produced by melt spinning method obtaining ribbons, and by casting technique into a copper mould, manufacturing rod shape samples with maximum diameter of 2 mm. Supercooled liquid region depends on chemical composition and exceeds 45 °C. Vickers microhardness of studied alloys is comparable to the highest ones for other Zr-based BMG.     

A polyethylene glycol-assisted route to synthesize Pb(Ni1/3Nb2/3)O3-PbTiO3 in pure perovskite phase

Ferroelectric relaxors (1 − x)Pb(Ni_1/3Nb_2/3)O_3−xPbTiO₃ (PNN-PT) with a composition (x = 0.36) near the morphotropic phase boundary (MPB) were prepared by a polyethylene glycol (PEG)-assisted solid-state reaction route. PEG with a molecular weight of 200 was introduced during the ball milling process of the raw oxide powders. XRD and TG/DSC results demonstrated that the interaction between PbO and PEG favors the transformation of lead-rich pyrochlore to lead-deficient pyrochlore, thus facilitating the formation of perovskite phase. Consequently, pure perovskite powders were synthesized at a relatively low temperature of 850 °C. Ceramics fabricated with the PEG-assisted route show a room temperature dielectric constant of 4987 and a maximum dielectric constant (at T_max) of 24,307 at a frequency of 1 kHz. The piezoelectric constant d₃₃ measured was 460 pC/N.     

Electrochemical performance of LiFe1−xVxPO4/carbon composites prepared by solid-state reaction

LiFe_1−xV_xPO₄/C cathode materials (x = 0, 0.1, 02, 0.3, 0.4) were synthesized by solid-state reaction using polypropylene as the reducing agent and carbon precursor. XRD results show that Li₉Fe₃P₈O₂₉ and Li₃V₂(PO₄)₃ occur when vanadium was added. TEM images show that most of LiFe_1−xV_xPO₄/C particles take on a spherical or quadrate shape with a size less than 200 nm. Electrochemical tests indicate that LiFe_0.9V_0.1PO₄/C and LiFe_0.8V_0.2PO₄/C have a flat discharge plateau at about 3.45 V versus Li⁺/Li and an initial discharge capacity higher than 150 mAh/g at 0.1 C. LiFe_0.8V_0.2PO₄/C also performed relatively good cycle stability which is attributed to their high electronic conductivity as proved by the electrochemical impedance spectroscopy (EIS). Cyclic voltammogram (CV) curves demonstrate that as increase of content of vanadium, LiFe_1−xV_xPO₄/C presents several couples of redox peaks.     

Oxidation behavior of NixFe1−x(OH)2 in Cl-containing solution

The addition of Ni leads to the formation of protective rust layer on steel and subsequently high corrosion resistance of steel in Cl⁻-containing environment. α-FeOOH, β-FeOOH, γ-FeOOH and Fe₃O₄ are formed mainly on steels exposed to Cl⁻-containing atmosphere. It is expected that systematic investigation of the effect of Ni(II) on the formation process of each oxide in solution should lead to elucidation of the role of Ni in the formation of anticorrosive oxide layer. This study reports the oxidation behavior of Ni_xFe_1−x(OH)₂ in Cl⁻-containing solution at two different pH regions (condition I under which solution pH is allowed to decrease and condition II under which solution pH is maintained at 8) where γ-FeOOH and Fe₃O₄ are predominantly formed, respectively, upon the oxidation of Fe(OH)₂. In the presence of Ni(II) in the starting solution, the formation of Ni(II) doped β-FeOOH with very low crystalline was facilitated and the formation of γ-FeOOH was suppressed with increasing Ni(II) content and with increasing oxidation rate of Fe(II). Ni(II) was found to have Fe₃O₄-suppressing effect under condition II.     

Substrates effect on Zn1−xMnxO thin films grown by RF magnetron sputtering

In this paper, we have presented the surface effect of the substrates on Mn doped ZnO (Zn_1−xMn_xO) thin films grown on Si(1 0 0) and sapphire [i.e. Al₂O₃(0 0 0 1)] by RF magnetron sputtering. These grown films have been characterized by X-ray diffraction (XRD), photoluminescence (PL) and vibrating sample magnetometer (VSM) to know its structural, optical and magnetic properties. All these properties have been found to be strongly influenced by the substrate surface on which the films have been deposited. The XRD results show that the Mn doped ZnO films deposited on Si(1 0 0) exhibit a polycrystalline nature whereas the films on sapphire substrate have only (0 0 2) preferential orientations indicating that the films are single crystalline. The studies of room temperature PL spectra reveal that the Zn_1−xMn_xO/Si(1 0 0) system is under severe compressive strain while the strain is almost relaxed in Zn_1−xMn_xO/Al₂O₃(0 0 0 1) system. It has been observed from VSM studies that Zn_1−xMn_xO/Al₂O₃(0 0 0 1) system shows ferromagnetic nature while the paramagnetic behaviour observed in Zn_1−xMn_xO/Si(1 0 0) system.     

Structural, magnetic and electrical transport properties for a series of La1−xSrxFe1−xMnxO3 (0.3 ≤ x ≤ 0.7) compounds

The structural, electrical transport and magnetic properties have been studied for compounds: La_1−xSr_xFe_1−xMn_xO₃ (0.3 ≤ x ≤ 0.7). The lattice parameter, a, first decreases with x, and followed by an increase when Sr²⁺ and Mn⁴⁺ was continuously doped. The cell parameters, b and c, slightly decrease with coupled substitution of Sr²⁺ for La³⁺ and Mn⁴⁺ for Fe³⁺. In the paramagnetic temperature range, formation of magnetic clusters is suggested; the sizes of clusters decrease with x up to 0.5, following that they increase sharply with continuing doping. The electrical behaviors of all specimens demonstrate insulators and the electrical resistivity increases with content of Mn⁴⁺ and Sr²⁺ ions doped. A variable range hopping model is suitable to describe electrical transport process for the compounds at low temperature. At high temperature the electrical transport process can be described by bipolaron model for all compounds.     

Thermoelectric properties of Sn1−x−yTiySbxO2 ceramics

Thermoelectric properties of Sn_1−x−yTi_y Sb_xO₂ ceramics were investigated in detail. The addition of Sb into SnO₂ matrix increased the electric conductivity, σ. The increase in the σ value should be caused by the increase in the carrier concentration. The Seebeck coefficients of all the samples were negative, which means that these samples have n-type conduction. The samples of this study have porous structure. The maximum Z value of all the samples measured in this study was 2.4 × 10⁻⁵ K⁻¹.     

Effect of potassium doping on the structural, magnetic and magnetocaloric properties of La0.7Sr0.3−xKxMnO3 perovskite manganites

We investigate the effect of potassium doping on the structural, magnetic and magnetocaloric properties of La_0.7Sr_0.3−xK_xMnO₃ (x = 0.05, 0.1, 0.15 and 0.2) powder samples. Our polycrystalline compounds were synthesized using the solid-state reaction at high temperature. X-ray diffraction characterizations showed that all our studied samples crystallize in the distorted rhombohedral system with space group. With increasing potassium content, the unit cell volume exhibits a broad maximum around x = 0.15. Magnetization measurements versus temperature showed that all our samples exhibit a paramagnetic to ferromagnetic transition with decreasing temperature. The Curie temperature T_C is found to decrease from 365 K for x = 0 to 328 K for x = 0.2 as well as the saturated magnetization M_sp which shifts from 3.68 μ_B/Mn for x = 0 to 3.05 μ_B/Mn for x = 0.2. The critical exponent γ defined as M_sp (T) = M_sp(0)[1−(T/T_C)]^γ is found to remain almost constant and equal to 0.33 for all our samples. The maximum of magnetic entropy changes |ΔS_max| of La_0.7Sr_0.3−xK_xMnO₃ for x = 0.05 and 0.15 is found to be respectively, 1.37 and 1.2 J kg⁻¹ K⁻¹ under a magnetic field change of 1 T.     

Investigation of hydrogen absorption/desorption properties of ZrMn0.85−xFe1+x alloys

The crystal structures and hydrogen absorption/desorption properties of the ZrMn_0.85−xFe_1+x alloys (x = 0, 0.2, 0.4) were investigated systematically. The pressure–composition (PC) isotherms and absorption kinetics were measured at 273–333 K by the volumetric method. Besides the crystal structure, the plateau pressure and the hydrogen intake capacity, this article also discussed the absorption kinetics, the pulverization resistance and the thermodynamic properties. XRD patterns revealed that ZrMn_0.85Fe and ZrMn_0.65Fe_1.2 were formed as hexagonal C14 laves phase structure while ZrMn_0.45Fe_1.4 possessed cubic C15 laves phase structure. With the increase of Fe and decrease of Mn, the plateau pressure increased while the hydrogen intake capacity lowered and the hydrogen absorption kinetics degraded. On the other hand, the hysteresis alleviated, the pulverization resistance improved and the stability of the hydrides decreased. The decomposition pressure was increased to more than 160 times for ZrMn_0.85Fe and more than 2500 times for ZrMn_0.65Fe_1.2 compared with that of the ZrMn₂ alloy.     

Thermo-physical and thermal cycling properties of plasma-sprayed BaLa2Ti3O10 coating as potential thermal barrier materials

Increased turbine inlet temperature in advanced turbines has promoted the development of thermal barrier coating (TBC) materials with high-temperature capability. In this paper, BaLa₂Ti₃O₁₀ (BLT) was produced by solid-state reaction of BaCO₃, TiO₂ and La₂O₃ at 1500 °C for 48 h. BLT showed phase stability between room temperature and 1400 °C. BLT revealed a linearly increasing thermal expansion coefficient with increasing temperature up to 1200 °C and the coefficients of thermal expansion (CTEs) are in the range of 1 × 10^− 5–12.5 × 10^− 6 K^− 1, which are comparable to those of 7YSZ. BLT coatings with stoichiometric composition were produced by atmospheric plasma spraying. The coating contained segmentation cracks and had a porosity of around 13%. The microhardness for the BLT coating is 3.9–4.5 GPa. The thermo-physical properties of the sprayed coating were investigated. The thermal conductivity at 1200 °C is about 0.7 W/mK, exhibiting a very promising potential in improving the thermal insulation property of TBC. Thermal cycling result showed that the BLT TBC had a lifetime of more than 1100 cycles of about 200 h at 1100 °C. The failure of the coating occurred by cracking at the thermally grown oxide (TGO) layer due to severe oxidation of bond coat. Based on the above merits, BLT could be considered as a promising material for TBC applications.     

Dip coating technique in fabrication of cone-shaped anode-supported solid oxide fuel cells

A simple and cost-effective dip coating technique was successfully developed to fabricate NiO-YSZ anode substrates for cone-shaped anode-supported solid oxide fuel cells. A single cell, NiO-YSZ/YSZ/LSM-YSZ, was assembled and tested to demonstrate the feasibility of the technique applied. Using humidified hydrogen (75 ml/min) as fuel and ambient air as oxidant, the maximum power density of the cell was 0.78 and 1.0 W/cm² at 800 and 850 °C, respectively. The observed open-circuit voltages (OCV) was closed to the theoretical value and the scanning electron microscope (SEM) results revealed that the microstructures of the anode substrate and the cathode layer are porous and the electrolyte film is dense.     

Studies on structural and thermal expansion properties of Ho2−xLnxMo4O15 (Ln = Er, Sm and Ce) solid solutions

Three new series of Ho_2−xEr_xMo₄O₁₅ (x = 0.0–2.0), Ho_2−xSm_xMo₄O₁₅ (x = 0.0–0.6) and Ho_2−xCe_xMo₄O₁₅ (x = 0.0–0.25) solid solutions have been prepared successfully by solid-state reaction and studied by powder X-ray diffraction. All the XRD patterns of these molybdates can be indexed in monoclinic space group P2₁/c. Lattice parameters a, b and c of Ho_2−xLn_xMo₄O₁₅ decrease linearly with increasing erbium content and increase with increasing samarium or cerium content. Thermal expansion behaviors of Ho_2−xLn_xMo₄O₁₅ have been investigated in the 25–500 °C temperature range with high-temperature X-ray diffraction. The temperature dependence of Mo(2)–O14 interaction looks like to be responsible for their thermal expansion behaviors.