Soft breakdown conduction in ultrathin (3-5 nm) gate dielectrics

Prior to any attempt to model a charge transport mechanism, a precise knowledge of the parameters on which the current depends is essential. In this work, the soft breakdown (SBD) failure mode of ultrathin (3-5 nm) SiO₂ layers in polysilicon-oxide-semiconductor structures is investigated. This conduction regime is characterized by a large leakage current and by multilevel current fluctuations, both at low applied voltages. In order to obtain a general picture of SBD, room-temperature current-voltage (I-V) measurements have been performed on samples with different gate areas, oxide thicknesses and substrate types. An astounding matching between some of these I-V characteristics has been found. The obtained results and the comparison with the final breakdown regime suggest that the current flow through a SBD spot is largely influenced by its atomic-scale dimensions as occurs in a point contact configuration. Experimental data are also presented which demonstrate that specific current fluctuations can be ascribed to a blocking behavior of unstable SBD conduction channels     

Tunneling leakage current in ultrathin (<4 nm) nitride/oxidestack dielectrics

The leakage current in high-quality ultrathin silicon nitride/oxide (N/O) stack dielectric is calculated based on a model of one-step electron tunneling through both the nitride and the oxide layers. The results show that the tunneling leakage current in the N/O stack is substantially lower than that in the oxide layer of the same equivalent oxide thickness (EOT). The theoretical leakage current in N/O stack has been found to be a strong function of the nitride/oxide EOT ratio: in the direct tunneling regime, the leakage current decreases monotonically as the M/O ratio increases, while in the Fowler-Nordheim regime the lowest leakage current is realized with a N/O EOT ratio of 1:1. Due to the asymmetry of the N/O barrier shape, the leakage current under substrate injection is higher than that under gate injection, although such a difference becomes smaller in the lower voltage regime. Experimental data obtained from high quality ultrathin N/O stack dielectrics agree well with calculated results     

MOS C-V characterization of ultrathin gate oxide thickness (1.3-1.8nm)

An equivalent circuit approach to MOS capacitance-voltage (C-V) modeling of ultrathin gate oxides (1.3-1.8 nm) is proposed. Capacitance simulation including polysilicon depletion is based on quantum mechanical (QM) corrections implemented in a two-dimensional (2-D) device simulator; tunneling current is calculated using a one-dimensional (1-D) Green's function solver. The sharp decrease in capacitance observed for gate oxides below 2.0 nm in both accumulation and inversion is modeled using distributed voltage-controlled RC networks. The imaginary components of small-signal input admittance obtained from AC network analysis agree well with measured capacitance     

Robust ultrathin oxynitride dielectrics by NH3nitridation and N2O RTA treatment

In this paper, a method to grow robust ultrathin (E_OT=28 Å) oxynitride film with effective dielectric constant of 5.7 is proposed. Samples, nitridized by NH₃ with additional N₂O annealing, show excellent electrical properties in terms of very low bulk trap density, low trap generation rate, and high endurance in stressing. This novel dielectric appears to be very promising for future ULSI devices     

Performance dependence of CMOS on silicon substrate orientation for ultrathin oxynitride and HfO/sub 2/ gate dielectrics

Dependence of CMOS performance on silicon crystal orientation of [100], [111], and [110] has been investigated with the equivalent gate dielectric thickness less than 3 nm. Hole mobility enhancement of /spl ges/160% has been observed for both oxynitride and HfO/sub 2/ gate dielectrics on [110] surfaces compared with [100]. CMOS drive current is nearly symmetric on [110] orientation without any degradation of subthreshold slope. For HfO/sub 2/ gate dielectrics, an approximately 68% enhancement of pMOSFET drive current has been demonstrated on [110] substrates at L/sub poly/=0.12 /spl mu/m, while current reduction in nMOS is around 26%.     

Furnace grown gate oxynitride using nitric oxide (NO)

Gate oxynitride was grown in NO for the first time. This approach can provide a tight N accumulation near the Si/SiO₂ interface. Much lower thermal budget is required for an NO process than for an N₂O process to produce an oxynitride with useful properties. Submicron MOSFET's with NO oxynitride showed superior current drive characteristics and comparable hot carrier immunity to those with N₂O oxynitride     

Improved method for the oxide thickness extraction in MOSstructures with ultrathin gate dielectrics

An improved method for the assessment of the oxide thickness applicable to advanced CMOS technologies is proposed. To this end, a proper combination of Maserjian's technique and of Vincent's method is used to alleviate the unknown parameter inherent to both extraction procedures and which depends on the employed carrier statistics. The new method has been successfully applied to various technologies with gate oxide thickness ranging from 7 nm to 1.8 nm     

1.6 nm oxide equivalent gate dielectrics using nitride/oxide (N/O)composites prepared by RPECVD/oxidation process

Ultrathin nitride/oxide (~1.5/0.7 nm) dual layer gate dielectrics have been formed using remote plasma enhanced CVD of nitride onto plasma-grown oxide interface layers. High accumulation capacitance (1.72 μF/cm²) is measured and the equivalent oxide thickness is 1.6 nm after quantum effect corrections. Compared to 1.6 nm oxides, a tunneling current reduction of more than 100 fold is found for devices with 1.6 nm N/O dielectrics due to increased film thickness and interface nitridation. Hole channel mobility decreases by about 5%, yielding very good P-MOSFET current drive. Excellent dielectric reliability and interface robustness are also demonstrated for P-MOSFET's with N/O dielectrics     

High quality interpoly dielectrics deposited on thenitrided-polysilicon for nonvolatile memory devices

High quality interpoly dielectrics have been fabricated by using NH₃ and N₂O nitridation on polysilicon and deposition of tetra-ethyl-ortho-silicate (TEOS) oxide with N₂O annealing. The surface roughness of polysilicon is improved and the value of weak bonds is reduced due to nitrogen incorporation at the interface, which improves the integrity of interpoly dielectrics. The improvements include a higher barrier height, breakdown strength, and charge-to-breakdown, and a lower leakage current and charge trapping rate than counterparts. It is found that this method can simultaneously improve both charge-to-breakdown (up to 20 C/cm² ) and electric breakdown field (up to 17 MV/cm)     

Comparison of neutral electron trap generation by hot-carrierstress in n-MOSFET's with oxide and oxynitride gate dielectrics

A comparative study of neutral electron-trap generation due to hot-carrier stress in n-MOSFETs with pure oxide, NH₃-nitrided oxide (RTN), and reoxidized nitrided oxide (RTN/RTO) as gate dielectrics is reported. Results show that neutral electron trap generation is considerably suppressed by nitridation and reoxidation. The nature of neutral traps is described based on the kinetics of trap filling by electron injection into the gate dielectrics immediately after channel hot-electron stress (CHES). Improved endurance of the RTN and RTN/RTO oxides is explained using physical models related to interfacial strain relaxation     

To optimize electrical properties of the ultrathin (1.6 nm)nitride/oxide gate stacks with bottom oxide materials andpost-deposition treatment

The electrical properties affected by the bottom oxide materials and the post-deposition treatment on the ultrathin (down to 1.6 nm) nitride/oxide (N/O) stacks, prepared by rapid thermal chemical vapor deposition (RTCVD) with two-step NH₃/N₂O post-deposition annealing, for deep submicrometer dual-gate MOSFETs have been studied extensively. N/O stack with NO-grown bottom oxide exhibits fewer flat-band voltage shifts and higher hole and electron mobility, but suffers from worse leakage current than that with conventional O₂-grown bottom oxide. In post-deposition treatment, increasing NH₃ nitridation temperature can effectively reduce the equivalent oxide thickness (EOT) and improve leakage current reduction rate, but can result in worse mobility. Furthermore, the subsequent N₂O annealing eliminates the defects and offers a contrary effect on the N/O stack in comparison with the NH₃ nitridation step     

Challenges and performance limitations of high-k and oxynitride gate dielectrics for 90/65 nm CMOS technology

For low power applications, the increase of gate leakage current, caused by direct tunneling in ultra-thin oxide films, is the crucial factor eliminating conventional SiO₂-based gate dielectrics in sub-90 nm CMOS technology development. Recently, promising performance has been demonstrated for poly-Si/high-k and poly-Si/SiON gate stacks in addressing gate leakage requirements for low power applications. However, the use of poly-Si gate electrodes on high-k created additional issues such as channel mobility and reliability degradations, as well as Fermi level pinning of the effective gate work function. Therefore, oxynitride gate dielectrics are being proposed as an intermediate solution toward the sub-65/45 nm nodes. Apparently, an enhanced SiON gate dielectric stack was developed and reported to achieve high dielectric constant and good interfacial properties. The purpose of this paper is to provide a comprehensive review some of the device performance and limitation that high-k and oxynitride as dielectric materials are facing for sub-65/45 nm node.     

High-quality ultrathin (1.6 nm) nitride/oxide stack gatedielectrics prepared by combining remote plasma nitridation and LPCVDtechnologies

Ultrathin nitride/oxide (N/O) gate dielectric stacks with equivalent oxide thickness of 1.6 nm have been fabricated by combining remote plasma nitridation (RPN) and low pressure chemical vapor deposition (LPCVD) technologies. NMOSFETs with these gate stacks exhibit good interface properties, improved subthreshold characteristics, low off-state currents, enhanced reliability, and about one order of magnitude reduction in gate leakage current to their oxide counterparts     

Simplified 0.35-μm flash EEPROM process using high-temperatureoxide (HTO) deposited by LPCVD as interpoly dielectrics and peripheraltransistors gate oxide

A simplified flash EEPROM process was developed using high-temperature LPCVD oxide both as flash cells interpoly dielectrics and as peripheral transistors gate oxide (decoding logic). An O₂ anneal at 850°C lowers charge trapping and interface trap density induced by Fowler-Nordheim injection. However, electron trapping remains slightly higher than with dry thermal oxide. Similar memory charge loss and write-erase endurance are obtained as for ONO-insulated cells. HTO thus proves to have the required quality and reliability to be used in flash EEPROMs     

Atomically smooth ultrathin oxide on Si(1 1 3)

We report the first direct observation of dissociative chemisorption of O₂ molecules on a Si surface. We link this to our other new observation that smooth oxide layers can be grown easily on Si(1 1 3). The initial oxidation is discussed in terms of surface diffusion paths and surface stress. Ab initio calculations help elucidate the favored adsorption sites and the oxidation mechanism.     

Improved radiation hardness of MOS devices with ultrathin nitrided oxide gate dielectrics prepared by rapid thermal processing

The radiation hardness of MOS devices with ultrathin nitrided oxides ( approximately 100 AA) prepared by rapid thermal nitridation (RTD) of thin oxides has been studied. The radiation was performed by exposing devices under X-rays of 50 keV to a dose of 0.5 Mrad(Si). Compared with conventional thermal oxides, the RTN oxide devices exhibit a much smaller increase in both the fixed charge N/sub f/ and the interface state D/sub it/ densities. In addition, it is found that higher RTN temperature and/or longer durations produce smaller Delta N/sub f/ and Delta D/sub it/.<>     

Gate oxide reliabilities in MOS (metal-oxide-semiconductor) structures with Ti-polycide gates

We have investigated the thermal degradation of gate oxide in metal-oxide-semiconductor (MOS) structures with Ti-polycide gates. We found that the Ti-diffusion into the underlying polysilicon and consequently to the gate oxide occurs upon thermal cycling processes, which results in the dielectric breakdown of the gate oxide. We also found that the Ti-diffusion is suppressed by the employment of the thin (about 5 nm) titanium nitride (TiN) diffusion barrier layer, which consequently improved the reliability characterisitics of gate oxide significantly.     

Formation of high quality ultrathin oxide/nitride (ON) stackedcapacitors by in situ multiple rapid thermal processing [DRAMcells]

High quality, ultrathin (<30 Å) SiO₂/Si₃ N₄ (ON) stacked film capacitors have been fabricated by in situ rapid-thermal multiprocessing. Si₃N₄ film was deposited on the RTN-treated poly-Si by rapid-thermal chemical vapor deposition (RTCVD) using SiH₄ and NH₃, followed by in situ low pressure rapid-thermal reoxidation in N₂O (LRTNO) or in O₂ (LRTO) ambient. While the use of low pressure reoxidation suppresses severe oxidation of ultrathin Si₃N₄ film, the use of N₂O-reoxidation significantly improves the quality of ON stacked film, resulting in ultrathin ON stacked film capacitors with excellent electrical properties and reliability     

基于等离子体氮化工艺的超薄栅氧化膜的电学特性和可靠性

介绍了利用MMT等离子体氮化工艺和炉管NO退火氮化工艺制备的超薄栅介质膜的电学特性和可靠性. 结合两种氮化工艺在栅介质膜中形成了双峰和单峰的氮分布. 通过漏极电流、沟道载流子和TDDB的测试,发现栅介质膜中双峰的氮分布可以有效提高器件的电学特性,更为重要的是可以极大提高器件的击穿特性. 这指明了延长掺氮氧化膜在超大规模集成电路器件栅介质层中应用的寿命,使之有可能进一步跟上技术的发展.     

Titanium-aluminum oxynitride (TAON) as high-k gate dielectric for sub-32 nm CMOS technology

High-k insulators for the next generation (sub-32 nm CMOS (complementary metal-oxide-semiconductor) technology), such as titanium-aluminum oxynitride (TAON) and titanium-aluminum oxide (TAO), have been obtained by Ti/Al e-beam evaporation, with additional electron cyclotron resonance (ECR) plasma oxynitridation and oxidation on Si substrates, respectively. Physical thickness values between 5.7 and 6.3 nm were determined by ellipsometry. These films were used as gate insulators in MOS capacitors fabricated with Al electrodes, and they were used to obtain capacitance-voltage (C-V) measurements. A relative dielectric constant of 3.9 was adopted to extract the equivalent oxide thickness (EOT) of films from C-V curves under strong accumulation condition, resulting in values between 1.5 and 1.1 nm, and effective charge densities of about 10¹¹ cm⁻². Because of these results, nMOSFETs with Al gate electrode and TAON gate dielectric were fabricated and characterized by current-voltage (I-V) curves. From these nMOSFETs electrical characteristics, a sub-threshold slope of 80 mV/dec and an EOT of 0.87 nm were obtained. These results indicate that the obtained TAON film is a suitable gate insulator for the next generation (MOS) devices.