γ ? α2 Phase transformation in fractured high temperature stress rupture Ti-48Al-2Nb(at.%)

The ₂ phase transformation in fractured high temperature stress rupture Ti-48Al-2Nb(at.%) alloy has been studied by analytical electron microscopy. ₂ and phases were found at grain boundaries. ₂ layers that suspended in layers and interfacial ledge higher than 2d ₍₁₁₁₎ at /₂ interfaces were observed in the lamellar grains. These facts indicated that ₂ phase transformation and dynamic recrystallization have occurred during high temperature stress rupture deformation. It can be concluded that deformation induced ₂ phase transformation and dynamic recrystallization resulted in the presence of particles at grain boundaries. A structural and compositional transition area between deformation-induced ₂(or ) and its adjacently original (or ₂) phases was found by HREM and EDS and is suggested as a way to transform between and ₂ phase during high temperature stress rupture deformation. The transition area was formed by slide of partial dislocations on close-packed planes and diffusion of atoms.     

Ultrasonic attenuation of longitudinal and shear waves in superconducting lead

Longitudinal and shear wave ultrasonic attenuations have been measured in high-purity Pb on two single crystals obtained from the same ingot. The measurements were done at low temperatures, at different frequencies, and in transverse magnetic fields, up to a field of 7.3 kG. The propagation directions in the two crystals were along [100] and [110]. For some propagation and polarization directions the _s / _n ratio is found to be frequency-independent, while for others, large divergences in the _s / _n ratios at different frequencies are observed. A sharp decrease of _s / _n nearT _c is observed for a particular longitudinal wave propagation, but not in any shear wave propagation. In some cases _s / _n is found to be abnormally high and this feature is associated with a peak in attenuation _n and a relatively high _n at 7.2 K. None of the _s / _n curves fits closely to any BCS energy gap. For longitudinal waves the high magnetic field (H) dependence of the normal state attenuation was found to agree qualitatively with the free electron theory for propagation along [100], but not for propagation along [110]. For shear waves the high-field attenuations do not extrapolate to zero asH tends to infinity. For all propagation and polarization directions the high-field attenuations show 1/H ² field dependence.     

Analytical electron microscopy of Al2O3 implanted with iron ions

Single crystals of -Al₂O₃ were implanted with iron ions at room temperature to fluences ranging from 4×10¹⁶ Fe cm^–2 to 1×10¹⁷ Fe cm^–2. The microstructure and composition in the implanted region were examined using analytical electron microscopy techniques. Special emphasis was placed on monitoring the microstructural changes which take place during post-implantation annealing. Clusters of metallic -Fe were identified in the specimen after implantation to a dose of 1×10¹⁷ Fe cm^–2. Analytical electron microscopy of implanted specimens annealed in oxygen revealed the redistribution of the implanted iron and the formation of surface precipitates of -Fe₂O₃, subsurface precipitates of various forms of spinel, and, in some cases, subsurface precipitates of iron, depending on the annealing temperature. Examination of implanted specimens annealed under reducing conditions revealed the presence of precipitates of -Fe.     

Growth of Gray Tin Crystals

A method is proposed for growing large -Sn single crystals without their disintegration as a result of the phase transition. -Sn crystals are prepared by freezing the closed system water–Sn–seed in such a way that the pressure exerted by the expanding ice minimizes the amount of -Sn nuclei and reduces the growth rate.     

Investigations of the copper isotope effect in oxygen-deficient YBa2Cu3O7−δ

We present data on the copper isotope effect (⁶³Cu-⁶⁵Cu), C_u =-nT_c/nm_Cu, for two isotopic pairs of oxygen-deficient YBa₂Cu₃O_7–, where varies between 0.06 and 0.52. _Cu is below 0.01 at =0.06 (fully oxygenated), it takes values between –0.14 and –0.34 in the 60 K plateau. Larger negative values of _Cu are observed away from the plateau. The dependence of _Cu is similar to that of the pressure effect dnT_c/dP.     

Formation of nanocrystalline phases in the Cu-Zn system during mechanical alloying

The evolution of various nanocrystalline phases in the Cu-Zn system during the course of mechanical alloying of elemental powder blends, manifests a similar sequence of phase formation in all the compositions. Zinc-rich phases were always first to form, which can be attributed to the diversities of diffusivities and diffusion distances in the constituents. The extent of zinc in -phase becomes significant only after turns nanocrystalline. The crystallite size of reached a minimum (18 nm) near the - phase boundary, while the and phases showed quite coarse crystallite size due to their low melting points. Alloying was sluggish during dry milling compared to wet milling, or at lower milling speed, which demonstrates the effects of oxidation during milling and lower milling energy.     

Eutectoid decomposition mechanisms in hypoeutectoid Ti-X alloys

A TEM study has been made of the bainite reaction in five hypoeutectoid Ti-X alloys, where X was successively cobalt, chromium, copper, iron and nickel. Rational orientation relationships were demonstrated amongst eutectoid , eutectoid intermetallic compound and the matrix in Ti-Ni, Ti-Co and Ti-Cr. Formation of Ti₂Co at : boundaries was observed. Eutectoid in bainite was found to be slightly misoriented with respect to proeutectoid , indicating that it is separately nucleated, perhaps sympathetically, rather than the result of the continued growth of proeutectoid . Eutectoid Ti₂Co and Ti₂Cu crystals in bainite were approximately equiaxed whereas Ti-Cr₂ crystals were elongated, a result ascribed to a ledge height-to-spacing ratio / at intermetallic compound crystal: boundaries approaching that of eutectoid (: boundaries in Ti-Cr but not in the other two systems. In the Ti-Fe alloy, eutectoid and eutectoid TiFe were directly observed to have ledged interphase boundaries with their matrix, but with different inter-ledge spacings and growth directions. Observation of pearlite lamellae growing normal to the broad faces of proeutectoid plates in the Ti-Ni alloy indicates that this mode of eutectoid decomposition, like that of bainite, can develop from partially coherent interphase boundaries. The suggestion was offered that pearlite forms when approachesh at the nucleating proeutectoid : interface and that bainite develops when h at this interface.     

Solid state phase transformation of BaB2O4 during the isothermal annealing process

Solid-state phase transformation of BaB₂O₄ during the isothermal annealing process for both to and to were investigated using a platinum crucible. For the -phase crystal at the -phase stable temperature (> 925 °C), the phase transforms to the phase perfectly below the melting temperature of 1100 °C. Meanwhile, for the -phase crystal at the -phase stable temperature (< 925 °C), the phase transforms to the phase perfectly above 800 °C. There is some difference in phase transformation behaviour between bulk-shape crystals and the powder, caused by thermal stress.     

Heat transfer in plane film formation

A mathematical model is obtained for the process of cooling with formation of a planar film. The solution obtained is verified experimentally.Notation mean axial velocity gradient - v_x current axial velocity - v_o initial polymer velocity - v₁ sampling velocity - K draw ratio - deformation rate tensor - x, y, z spatial coordinates - X, Y dimensionless coordinates - L() differential operator - T temperature - T_o initial temperature - T_c temperature of surrounding medium - dimensionless temperature - dimensionless temperature averaged over film thickness - thermal-diffusivity coefficient - 2_o initial film thickness - thermal conductivity - heat-transfer coefficient - f(X) distance function - Bi Biot criterion, Bi_o, Biot criterion calculated for initial film thickness - Gz* modified Graetz criterion - V dimensionless velocity - ₁, ₂, ₃ heat-transfer coefficients produced by radiation, free convection, and forced convection - v_c, _c mean velocity and film half-thickness in formation zone - T₁ calculated temperature value - T₂ experimental temperature value - l formation zone length Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 37, No. 5, pp. 854–858, November, 1979.     

Effects of silica on the bioactivity of calcium phosphate composites <Emphasis Type="Italic">in vitro</Emphasis>

In the present study, silica-calcium phosphate composites (SiO₂-CaP composites) were developed by mixing the starting materials (SiO₂ and CaHPO₄) in different ratios with the addition of 0.1% w/v NaOH solution. The phase composition of the SiO₂-CaP composites was determined by XRD and FTIR. After thermal treatment at 350 ^C/1 h and at 1000 ^C/3.5 h; all SiO₂-CaP composites composed of -quartz, -cristobalite and -Ca2P2O7. The presence of calcium phosphate enhanced the transformation of -quartz into -cristobalite at 1000 ^C. SEM observation indicated favorable attachment and spreading of neonatal rat calvaria osteoblasts onto the surface of silica-rich SiO₂-CaP composites. After attachment, these cells produced significantly higher amount of protein and expressed higher AP activity than cells attached to silica-poor samples. Results of the study suggested that the silica-based composites are more bioactive than calcium phosphate-based composites. Silica promoted the expression of osteoblast phenotype by both solution-mediated effect and direct interaction with the surface of the substrate.     

Flux-line cutting in type II superconductors

Experimental evidence for flux-line cutting in superconductors (intersection and cross-joining of singly quantized vortices) is briefly reviewed. The interaction energy between two straight vortices tilted at an angle ( 0)is then shown to be finite in the London model, i.e., in the limit of vanishing core radius. Next, the activation energy and maximum interaction force are calculated for the vortices in an analytic approximation to the Ginzburg-Landau theory. Here two competing interactions determine the behavior. Electromagnetic repulsion (0 < < /2) varies as cos and decays over distances scaled by the penetration depth , while core attraction is independent of and varies over distances scaled by the coherence length . The force is always repulsive at large flux-line separation (0 < < /2) and its maximum decreases rapidly as decreases, so that flux-line cutting isexpected to be more probable in low- materials. The calculations provide a basis for explaining longitudinal flux-flow resistance as well as some intriguing magnetization behavior in the same configuration.This work was supported by the U.S. Department of Energy, Office of Basic Energy Sciences, Materials Sciences Division, and by the Deutsche Forschungsgemeinschaft.On leave from Max-Planck-Institut für Metallforschung, Institut für Physik, Stuttgart, West Germany.On leave from New University of Ulster, Coleraine, Northern Ireland.     

Preferentially orientated precipitation in MnTiO3 single crystals

Preferentially orientated precipitation of -TiO₂ (rutile) needles in single crystals of MnTiO₃ grown by a floating-zone method under a controlled atmosphere of oxygen fugacity was studied. Optical microscopy and X-ray analysis revealed that the orientation relation between the -TiO₂ precipitates and the MnTiO₂ matrix is: {000 1}MnTiO₃// {111}-TiO₂ and 11¯20MnTiO₃// 110-TiO₂. The precipitation phenomenon was explained by introducing a nucleation and growth mechanism which was experimentally supported by heat treating experiments.     

Specific analysis of EBSD data to study the texture inheritance due to the β → α phase transformation

A specific processing of EBSD data is proposed to study the texture inheritance of titanium or zirconium alloys. A non standard misorientation map is calculated to localise the colonies inherited from the same parent grain. The calculation of the parent orientation from its inherited variants detailed in previous works has been adapted to the data obtained from an automated EBSD analysis. Finally, a method to derive the orientation map of the parent phase from that of the inherited phase is proposed. The resulting and COMs are used to study some aspects of the variant selection occurring in the transformation of a T40 sample.     

Anisotropic grain growth of R-α-sialon (R = Nd and Er)

Two R--sialon (R_0.6Si_9.3Al_2.7O_0.9N_15.1, R=Nd and Er) compositions were first fired at 1750°C/25 min and 1650°C/2 h respectively for completion of the phase transformation. Elongated -sialon grain morphology was developed in both samples after being re-fired at 1800°C for different periods of time. The growth in width of R--sialon grains is controlled by diffusion in the liquid, while the length growth tends to be interfacial reaction controlled. The anisotropic growth of R--sialon is attributed to the large difference in the growth rate constant between the length and the width directions of the grain.     

Effect of Intense Self-Irradiation on the Phase Composition of Metallic Plutonium

The crystal structure of film samples of "high-level" (based on ²³⁸Pu) and low-level (based on ²³⁹Pu) metallic plutonium during their prolonged (up to 343 days) storage (self-irradiation) at room temperature was studied by X-ray diffraction. In the samples of high-level plutonium, the -Pu and -Pu lattices coexist. In the period of 40-60 days, the other known crystal modifications of plutonium (-Pu, -Pu, -Pu, and -Pu) are also present. Low-level plutonium had only the -Pu lattice. A possible origin of this phenomenon is discussed.     

On the analysis of tunneling data for A15 superconductors

We examine the applicability of the standard McMillan inversion of Eliashberg's equations for superconductors with a nonconstant electronic density of statesN(). We do this usign simple models forN() and a realistically shapedN() taken from recent band structure work for Nb₃Sn. It turns out that peak structure inN() near _F may lead to gross errors in the derived Eliashberg function ²F() when the energy dependence ofN() is omitted in the inversion procedure. For Nb₃Sn, this leads to a 40% overestimate of when ²F() is evaluated via the standard McMillan program.     

Structural studies of nylon 13,13

A structural study of nylon 13,13 has been carried out by means of X-rays and electron microscopy. Both X-ray and electron diffraction data, obtained from oriented films as well as from lamellar crystals prepared in solution, evidenced that nylon 13,13 adopts a structure in a monoclinic lattice of parameters a _o=0.488 nm, b _o=0.473 nm, c _o=3.40 nm, ==90°, =121°. As expected from the constitution of the nylon, no trace of structure with chains in fully extended conformation (-form) was observed throughout this study.     

Thermal Expansion and Isothermal Compressibility of TlIn1 – xNdxSe2 (0 ≤ x≤ 0.08) Crystals

The thermal expansion coefficient () and isothermal compressibility ( _T ) of TlIn_{1 – x} Nd _x Se₂(0 x 0.08) crystals were measured between 77 and 400 K. In the range 77–160 K, both and _T increase with temperature, the increase in being much steeper. At higher temperatures, and _T change very little. The observed composition dependences of and _T are interpreted in terms of energy-band structure.     

Mössbauer studies of α″-Fe16N2 and α′-Fe8N films

Conversion-electron Mössbauer spectra of epitaxial -Fe₁₆N₂ and -Fe₈N films have been studied and their differences are discussed in detail. The Mössbauer spectrum of -Fe₁₆N₂ can be decomposed into three subspectra, which correspond to the 4d, 8h and 4c sites. The Mössbauer spectrum of -Fe₈N can be fitted using four spectra based on a nitrogen-atom-random-distribution model. The average hyperfine field is larger (3%) for -Fe₁₆N₂ than for -Fe₈N, which is approximately consistent with a 4.1% enhancement of the magnetic moments for -Fe₁₆N₂. The iron moments tend to locate in the film plane for -Fe₁₆N₂ and to arrange perpendicularly to the film plane for -Fe₈N.     

Effects of the variation in α-phase volume fraction on the thermal stability of TiAl alloys with a lamellar microstructure

The thermal stability of two-phase ( + ) lamellar microstructure in Ti-Al-Mo PST (polysynthetically twinned that has single colony) crystals, containing C or Si, was investigated. In addition, the variation of -phase volume fraction in Ti-Al-Mo-(C,Si) systems was investigated at several temperatures. Ti-46Al-1.5Mo-0.2C and Ti-46Al-1.5Mo-1.0Si alloys did not recrystallized (stable in this paper) during heat treatments at various heating rates and temperatures. Moreover, the -phase volume fractions of Ti-46Al-1.5Mo-0.2C and Ti-46Al-1.5Mo-1.0Si alloys which were stable compositions, changed less than those of Ti-47Al and Ti-46Al-1.5Mo alloys which were unstable compositions. The instability of the latter alloys was caused by their relatively higher variation of -phase volume fraction during heating. Therefore, it is suggested that the variation of -phase volume fraction is an important factor in controlling the thermal stability of lamellar microstructure.