CMC-g-PAA/APT/HA复合高吸水性树脂的制备与溶胀性能

以羧甲基纤维素(CMC)为基质,丙烯酸(AA)为单体,凹凸棒黏土(APT)和腐植酸(HA)为复合组分,采用水溶液聚合法制备了羧甲基纤维素接枝聚丙烯酸/凹凸棒黏土/腐植酸(CMC-g-PAA/APT/HA)环境友好复合高吸水性树脂,用红外光谱(FTIR)进行了结构表征。考查了APT和HA含量对树脂吸水倍率和吸水速率的影响,研究了树脂在不同pH溶液中的溶胀行为以及反复吸水性能。试验结果表明,APT和HA通过其表面的活性基团参与了接枝共聚反应,在体系中引入HA和APT能够显著提高复合高吸水性树脂的吸水能力。在HA含量为5%(质量分数),APT含量为30%(质量分数)时,树脂可达到最优吸蒸馏水倍率为582g/g。该复合高吸水性树脂在pH值在4～11范围内时具有较高的吸水性能,表现出优异的pH稳定性。经过5次反复溶胀后,该复合吸水树脂仍能达到424g/g的吸水倍率,较不含APT和HA样品提高了近44%。     

GG-g-PAA／SH高吸水性树脂的制备与缓释性能研究

以天然瓜尔胶（GG）、丙烯酸（AA）和腐植酸钠（SH）为原料,过硫酸铵为引发剂,N,N’-亚甲基双丙烯酰胺为交联剂,采用水溶液聚合法制备了环境友好的多功能瓜尔胶接枝聚丙烯酸／腐植酸钠（GG-g—PAA／SH）高吸水性树脂。考察了腐植酸钠含量对树脂吸水性能的影响,评价了树脂在沙土中的实际保水性能、反复溶胀性能和腐植酸钠肥料缓释性能。结果表明,在体系中引入廉价的腐植酸钠,不但降低生产成本,还能提高树脂的吸水能力,当腐植酸钠含量为15wt％时,高吸水性树脂吸蒸馏水和生理盐水的倍率分别为532g／g和62g／g。在沙土中加入高吸水性树脂能显著提高其保水性能,30d后仍能保持13％的水分。此外,GG-g-PAA／SH高吸水性树脂还具有较优的反复溶胀性能和腐植酸钠肥料缓释功能,可用作兼具吸水、保水和缓释性能的新型节水材料。     

PVA/PAA/CMC高吸水树脂的合成和性能研究

以聚乙烯醇(PVA)、丙烯酸(AA)和羧甲基纤维素钠(CMC)为原料,过硫酸钾(KPS)为引发剂,N,N-亚甲基双丙烯酰胺(MBA)为交联剂,采用超声辐射法合成了PVA/PAA/CMC高吸水树脂,利用FTIR对树脂进行了表征。考察了PVA、CMC、MBA、KPS用量和中和度对高吸水树脂吸水倍率的影响,研究了树脂在去离子水、不同盐溶液和pH溶液的吸水速率。实验结果表明:PVA、CMC和AA之间发生了共聚反应,在实验最优合成条件下,制备的高吸水树脂对去离子水和生理盐水的吸水倍率分别为835 g/g和86 g/g。适量引入PVA和CMC可以显著提高树脂的吸水倍率以及改善树脂的耐盐性能,树脂具有较高的吸水速率。     

聚丙烯酸钠吸水树脂的合成及性能研究

用NaOH中和后的丙烯酸为单体,以过硫酸钾K_2S_2O_8为引发剂,以N,N-亚甲基双丙烯酰胺为交联剂,采用水溶液聚合法合成了聚丙烯酸钠吸水树脂,考查了中和度,引发剂用量,交联剂用量对聚丙烯酸钠吸水树脂性能的影响,吸水倍率测试结果表明,当丙烯酸的中和度为80%、K_2S_2O_8用量为占丙烯酸单体质量分数的0.18%、N,N-亚甲基双丙烯酰胺用量为占丙烯酸单体质量分数的0.02%时,聚丙烯酸钠吸水树脂的吸水性能最佳,为165 g/g,该树脂对质量分数为20%的NaCl盐水的吸收倍率为31.6 g/g。     

微波辐射制备阿拉伯胶接枝2-丙烯酰胺基-2-甲基丙磺酸高吸水树脂及溶胀性能

以阿拉伯胶(GA),2-丙烯酰胺基-2-甲基丙磺酸(AMPS)为原料,N,N-亚甲基双丙烯酰胺(NMBA)为交联剂,过硫酸钾(APS）为引发剂,采用微波辐射方法制备了GA-g-PAMPS 高吸水性树脂。探讨了单体配比、交联剂用量、引发剂用量、中和度、微波功率和辐射时间对吸水倍率的影响,研究了树脂的溶胀性能,并用FTIR对吸水性树脂的结构进行了表征。结果表明：最佳合成条件下树脂吸去离子水倍率为683g/g,吸生理盐水倍率为137g/g。树脂的吸水倍率随着无机盐溶液浓度的增加而减小,在不同价态金属离子盐溶液中,树脂的吸水倍率顺序为NaCl>BaCl2> FeCl3,树脂具有较高的吸水速率和较好的重复吸水性能。     

微波辐射阿拉伯胶接枝2-丙烯酰胺基-2-甲基丙磺酸制备高吸水树脂及溶胀性能

以阿拉伯胶(GA)、2-丙烯酰胺基-2-甲基丙磺酸(AMPS)为原料,N,N-亚甲基双丙烯酰胺(NMBA)为交联剂,过硫酸钾(APS)为引发剂,采用微波辐射方法制备了GA-g-PAMPS高吸水性树脂。探讨了单体配比、交联剂用量、引发剂用量、中和度、微波功率和辐射时间对吸水倍率的影响,研究了树脂的溶胀性能,并用FTIR对吸水性树脂的结构进行了表征。结果表明:最佳合成条件下得到的树脂吸去离子水倍率为683 g/g,吸生理盐水倍率为137 g/g。树脂的吸水倍率随着无机盐溶液浓度的增加而减小,在不同价态金属离子盐溶液中,树脂的吸水倍率从大到小的顺序为Na ClBa Cl2Fe Cl3,树脂具有较高的吸水速率和较好的重复吸水性能。     

微波辐射制备阿拉伯胶接枝2-丙烯酰胺基-2-甲基丙磺酸高吸水树脂及溶胀性能

以阿拉伯胶(GA),2-丙烯酰胺基-2-甲基丙磺酸(AMPS)为原料,N,N-亚甲基双丙烯酰胺(NMBA)为交联剂,过硫酸钾(APS）为引发剂,采用微波辐射方法制备了GA-g-PAMPS 高吸水性树脂。探讨了单体配比、交联剂用量、引发剂用量、中和度、微波功率和辐射时间对吸水倍率的影响,研究了树脂的溶胀性能,并用FTIR对吸水性树脂的结构进行了表征。结果表明：最佳合成条件下树脂吸去离子水倍率为683g/g,吸生理盐水倍率为137g/g。树脂的吸水倍率随着无机盐溶液浓度的增加而减小,在不同价态金属离子盐溶液中,树脂的吸水倍率顺序为NaCl>BaCl2> FeCl3,树脂具有较高的吸水速率和较好的重复吸水性能。     

淀粉/钠基蒙脱土/聚丙烯酸高吸水树脂的制备研究

本文以丙烯酸(AA)、淀粉等为原料,复合钠基蒙脱土,利用水溶液聚合法,合成制备一种复合型高吸水树脂油田堵漏剂,并在此基础上探索影响吸水树脂吸水性能的因素。最佳吸水性能的工艺条件为:70℃条件下调单体中和度至70%、N,N’-亚甲基双丙烯酰胺0.065 g、过硫酸钾为0.044 g,蒙脱土3 g。所得产品:吸水倍率251.3 g/g、吸盐倍率69.2 g/g。最佳吸盐水配方条件为:60℃条件下调单体中和度至75%、N,N’-亚甲基双丙烯酰胺0.075 g、过硫酸钾为0.049 g、蒙脱土3 g;所得产品:吸水倍率238.2 g/g、吸盐倍率81.5 g/g。样品吸水后为无色透明块状胶体,烘干粉碎后为淡黄色颗粒。     

大颗粒吸水树脂的制备工艺及其性能

采用反相悬浮聚合制备了大颗粒聚丙烯酰胺-丙烯酸-丙烯酸钠[P(AM-AA-SA)]树脂微球,考察了搅拌速率与乳化剂对树脂微球粒径的影响,交联剂用量、单体配比和丙烯酸中和度对330μm树脂微球吸水倍率的影响,丙烯酸丁酯的用量对树脂吸水速率的影响以及树脂微球在80℃下的保水性能.结果表明:制备的树脂吸去离子水量达983.0 g/g,对NaCl和CaCl2溶液的吸水倍率最大值分别为91 3,15.6 g/g,在80℃下有良好的保水性能,丙烯酸丁酯的加入可将吸水饱和时间延长2倍.     

P(AA/AM/APEG)/纳米二氧化硅复合高吸水树脂的合成及性能

以丙烯酸(AA)、丙烯酰胺(AM)、烯丙基聚氧乙烯醚(APEG)为单体,再引入纳米二氧化硅(nano-SiO_2),以过硫酸铵为引发剂,N,N-亚甲基双丙烯酰胺(MBA)为交联剂,采用水溶液聚合法制备了P(AA/AM/APEG)/纳米二氧化硅有机/无机复合高吸水性树脂,考察了交联剂加量、引发剂加量、纳米二氧化硅加量对树脂吸水倍率的影响,并用红外光谱和扫描电镜对产物进行了表征。结果表明:合成最佳条件加入纳米二氧化硅能提高树脂的吸水性能,粒径在80~120目时,复合树脂吸水倍率达到1 865 g/g,P(AA/AM/APEG)树脂吸水倍率为1 681g/g;温度在20~60℃时,复合吸水树脂吸水倍率变化幅度不大;pH在6~8时,其吸水性能最好,吸水倍率为1 865~1 444 g/g;此外,复合树脂具有较好的保水性能,树脂常温下保存15 d,其保水率达到83.2%。红外光谱和扫描电镜分析表明,纳米二氧化硅成功接枝到聚合物上并形成海绵状结构。     

Synthesis,swelling behaviors,and slow‐release characteristics of a guar gum‐g‐poly(sodium acrylate)/sodium humate superabsorbent

Superabsorbents used in agricultural and ecological projects with low‐cost, slow‐release fertilizers and environmentally friendly characteristics have been extensively studied. The use of a natural polymer as the matrix and then further polymerization with some functional material has become the preferred method. In this work, with natural guar gum (GG), partially neutralized acrylic acid, and sodium humate (SH) as the raw materials, ammonium persulfate as the initiator, and N,N′‐methylenebisacrylamide (MBA) as the crosslinker, GG‐g‐poly(sodium acrylate) (PNaA)/SH superabsorbents were synthesized through a solution polymerization reaction and were characterized with Fourier transform infrared spectroscopy, scanning electron microscopy, and thermogravimetric analysis. The effects of the SH content and MBA concentration on the water absorbency were investigated. The results showed that the introduction of SH into the GG‐g‐PNaA system could improve the water absorbency, swelling rate, pH‐resistant property, and reswelling capability, and the superabsorbent containing 15 wt % SH had the highest water absorbency of 532 g/g of sample in distilled water and 62 g/g of sample in a 0.9 wt % NaCl solution. The slow release in water and water retention in sandy soil tests revealed that the superabsorbent could act as a fertilizer as well as an effective water‐saving material for agricultural applications. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

静态溶液聚合法合成SA-IP-SPS型高吸水性树脂

采用氯磺酸磺化法制备了聚乙烯醇硫酸钠（SPS）,以工业级丙烯酸和SPS为原料采用静态溶液聚合法合成了具有良好吸水、吸盐水性能及较高热稳定性的聚丙烯酸（盐）-聚乙烯醇硫酸钠互穿网络型高吸水性树脂（SA-IP-SPS）,红外光谱、热重分析、硫含量分析结果表明了SA-IP-SPS互穿网络结构的形成.对SPS含量、PVA分子量的考察结果表明：PVA相对分子质量在90000～124000,SPS含量在3%左右时得到的SA-IP-SPS高吸水性树脂吸附性能最高（吸水900g·g^-1,吸0.9%食盐水97 g·g^-1）.     

Preparation and slow‐release property of a poly(acrylic acid)/attapulgite/sodium humate superabsorbent composite

A novel poly(acrylic acid)/attapulgite (APT)/sodium humate (SH) superabsorbent composite was synthesized through the graft copolymerization reaction of acrylic acid on APT micropowder and SH with N,N′‐methylene bisacrylamide as a crosslinker and ammonium persulfate as an initiator in an aqueous solution. Various effects on the water absorbency, including the amounts of the crosslinker, initiator, APT, and SH, were investigated. The superabsorbent composite was characterized with Fourier transform infrared spectroscopy and scanning electron microscopy. The superabsorbent composite synthesized under optimal synthesis conditions with an APT concentration of 20% and an SH concentration of 20% exhibited absorption of 583 g of H₂O/g of sample and 63 g of H₂O/g of sample in distilled water and in a 0.9 wt % NaCl solution, respectively. The slow‐release property of SH from the superabsorbent composite into water was measured, and a test of the water retention of the superabsorbent composite in soil was also carried out experimentally with and without the superabsorbent composite. The results showed that the superabsorbent composite had not only good water retention but also an additional slow‐release property of SH. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 37–45, 2007     

Study on superabsorbent composites. XVIII. Preparation,characterization, and property evaluation of poly(acrylic acid‐co‐acrylamide)/organomontmorillonite/sodium humate superabsorbent composites

A series of novel multifunctional poly (acrylic acid‐co‐acrylamide) (PAA‐AM)/organomontmorillonite (O‐MMT)/sodium humate (SH) superabsorbent composites were synthesized by the graft copolymerization reaction of partially neutralized acrylic acid and acrylamide on O‐MMT micropowder and SH with N,N′‐methylene bisacrylamide as a crosslinker and ammonium persulfate as an initiator in an aqueous solution. The superabsorbent composites were characterized by means of Fourier transform infrared spectroscopy, X‐ray diffraction, scanning electron microscopy, and thermogravimetric analysis. The effect of the relative weight ratio of SH to O‐MMT on the water absorbency was studied, and the results indicated that the best water absorbency of 591 g/g in distilled water was obtained when an O‐MMT content of 20 wt % and an SH content of 30 wt % were incorporated. The superabsorbent composite possessed a good capacity for water retention; even after 30 days, 24.4 wt % of water could still be saved by the sand soil containing 1.0 wt % superabsorbent composite. The results from this study show that the water absorbency of a superabsorbent composite is improved by the simultaneous introduction of O‐MMT and SH into a PAA‐AM network in comparison with the incorporation of only O‐MMT or SH. Also, in comparison with PAA‐AM/MMT/SH, an appropriate amount of O‐MMT can benefit the developed composites with respect to their water absorbency, salt resistance, and capacity for water retention in sand soil. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Enhanced oxygen‐barrier and water‐resistance properties of poly(vinyl alcohol) blended with poly(acrylic acid) for packaging applications

To enhance the oxygen‐barrier and water‐resistance properties of poly(vinyl alcohol) (PVA) and expand its food packaging applicability, five crosslinked poly(vinyl alcohol)/poly(acrylic acid) (PVA/PAA) blend films were prepared via esterification reactions between hydroxyl groups in PVA and carboxylic acid groups in PAA. The physical characteristics of the blends, including the thermal, barrier, mechanical and optical properties, were investigated as a function of PAA ratio. With increasing PAA content, the crosslinking density was significantly increased, resulting in changes in the chemical structure, morphology and crystallinity of the films. The oxygen transmission rate of pure PVA decreased from 5.91 to 1.59 cc m^?1 day^?1 with increasing PAA ratio. The water resistance, too, increased remarkably. All the blend films showed good optical transparency. The physical properties of the blend films were strongly correlated with the chemical structure and morphology changes, which varied with the PAA content. © 2016 Society of Chemical Industry     

Dual-responsive release behavior of pH-sensitive PVA/PAAc hydrogels containing temperature-sensitive PVA/PNIPAAm microcapsules

Both temperature and pH responsive drug delivery system was prepared by combining temperature-sensitive poly(vinyl alcohol) (PVA)/poly(N-isopropylacrylamide) (PNIPAAm) microcapsules and pH-sensitive PVA/poly(acrylic acid) (PAAc) hydrogels. The release of drug from the composite hydrogels increased as the pH increased due to the repulsion among the carboxylate anions in the PVA/PAAc hydrogels. The release of drug from the composite hydrogels also increased as the temperature decreased due to the higher hydrophilicity generated below the lower critical solution temperature of PNIPAAm. The compression moduli of composite hydrogels increased with increasing the content of PVA/PNIPAAm microcapsules. The biocompatibility of composite hydrogels was confirmed by the cytotoxicity test.     

Electrospinning of chitosan/poly(vinyl alcohol)/acrylic acid aqueous solutions

Chitosan bicomponent fibers were prepared via the electrospinning of chitosan/poly(vinyl alcohol)/acrylic acid aqueous solutions with different concentrations. With a 4% acrylic acid aqueous solution, when the chitosan/poly(vinyl alcohol) mass ratios were lower than 80/20, electrospinning nanofibers could be obtained. With a 90% acrylic acid aqueous solution, when the chitosan/poly(vinyl alcohol) mass ratios were less than 95/5, good nanofibers could be electrospun. The average diameter of the nanofibers gradually decreased, and its distribution became narrower as the poly(vinyl alcohol) concentration increased. Chitosan/poly(vinyl alcohol)/acrylic acid aqueous solutions could be electrospun at various concentrations by the adjustment of the chitosan and poly(vinyl alcohol) concentrations. The effects of the viscosity and conductivity of the blend solution on the morphologies of the fiber mats were also investigated. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5692–5697, 2006     

Synthesis and Characterization Superabsorbent Polymers Made of Starch,Acrylic Acid,Acrylamide, Poly(Vinyl Alcohol), 2-Hydroxyethyl Methacrylate, 2-Acrylamido-2-methylpropane Sulfonic Acid

Three polymers with excellent absorption properties were synthesized by graft polymerization: soluble starch-g-poly(acrylic acid-co-2-hydroxyethyl methacrylate), poly(vinyl alcohol)/potato starch-g-poly(acrylic acid-co-acrylamide), poly(vinyl alcohol)/potato starch-g-poly(acrylic acid-co-acrylamide-co-2-acrylamido-2-methylpropane sulfonic acid). Ammonium persulfate and potassium persulfate were used as initiators, while N,N′-methylenebisacrylamide was used as the crosslinking agent. The molecular structure of potato and soluble starch grafted by synthetic polymers was characterized by means of Fourier Transform Infrared Spectroscopy (FTIR). The morphology of the resulting materials was studied using a scanning electron microscope (SEM). Thermal stability was tested by thermogravimetric measurements. The absorption properties of the obtained biopolymers were tested in deionized water, sodium chroma solutions of various concentrations and in buffer solutions of various pH.     

Synthesis and Swelling Behavior of Superabsorbents Cross-Linked with N-Maleyl Chitosan

A kind of superabsorbent based on the monomers maleic anhydride (MA) and acrylic acid (AA) was prepared by solution polymerization using ammonium peroxodisulfate (AP) and sodium bisulfite (NaHSO₃) as initiator, and N-maleyl chitosan (N-MACH) as cross-linker. Effects of process parameters such as the amount of cross-linker, mass ratio of MA to AA, and neutralization degree of AA on the water absorbency of superabsorbents are discussed. The results indicated the water absorbency of superabsorbents increased and then decreased with the increase of MA content, the amount of the N-MACH cross-linker, and the neutralization degree of AA. Under the optimal conditions, the water absorbency of superabsorbents could reach l560.42 g/g and 83.7 g/g in distilled water and in 0.9% NaCl solution, respectively. In addition, to enhance the water absorbency of superabsorbents in 0.9% NaCl solution, polyvinyl alcohol (PVA) was introduced as interpenetrating polymer in the network and 2-acrylamido-2-methyl propane sulfonic acid (AMPS) was introduced as comonomer. It was proved that PVA and AMPS could effectively improve the water absorbency of superabsorbents both in distilled water and 0.9% NaCl solution.