Adsorption of benzoic acid by CTAB exchanged montmorillonite

This paper reports the adsorption of benzoic acid from water on cetyl trimethylammonium exchanged montmorillonite (CTAB-montmorillonite). Important factors are the adsorbent concentration, ionic strength, equilibrium time and pH. The largest adsorption is at pH 9. The adsorption kinetics data fitted the pseudo-second-order equation. The adsorption isotherms at different pH were linear indicating a partition mechanism. Up to about 61% of the dissolved benzoic acid was adsorbed by CTAB-montmorillonite. These results indicate that CTAB-montmorillonite is a potential adsorbent for benzoic acid.     

Removal of metal ions from aqueous solution by adsorption onto activated carbon cloths: adsorption competition with organic matter

Activated carbon cloths are recent adsorbents whose adsorption properties are well known for monocomponent solutions of organics or metal ions. However, to treat wastewaters with these materials, their performance has to be determined in multicomponent solution. This work studies adsorption competition between metal ions (Cu²⁺, Pb²⁺) and organic matter (benzoic acid). The first part investigates adsorption equilibrium of monocomponent metal ions solutions and shows the dependence of adsorption capacities on adsorbent porosity and metal ions chemical properties (molecular weight, ionic radius and electronegativity). The influence of pH is also demonstrated. The second part focuses on adsorption competition: (1) between both metal ions (a decrease of adsorption capacities is observed, whose value is related to adsorption kinetics of metal ions); (2) between metal ions and organic matter, in solution or adsorbed onto the activated carbon cloth (a strong influence of pH is shown: when benzoic acid is under benzoate form, in both cases adsorption is increased due to the formation of ligands between adsorbed benzoate ions and metals).     

腐植酸在含酚废水处理中的实验研究

对腐植酸吸附剂处理含酚废水进行了实验研究,考察了吸附时间、温度、pH值对吸附率的影响,通过改变腐植酸用量与化学耗氧量(CODCr)的关系探讨了其在工业应用的可能性。结果表明,腐植酸对含酚废水有较好的处理效果,在pH=1.0时,室温下吸附12h,吸附率可达95%以上;腐植酸用量为0.5g/10mL废水时,CODCr值可降至50mg/L以下。     

Synthesis of polyelectrolyte-modified ordered nanoporous carbon for removal of aromatic organic acids from purified terephthalic acid wastewater

In this work polyelectrolyte (polydiallyldimethylammonium chloride) modified ordered mesoporous carbon (CMK-1/PDDA) has been synthesized and has been employed in removal of major aromatic compounds present in purified terephthalic acid wastewater, such as p-toluic acid, benzoic acid, 4-carboxybenzaldehyde, phthalic acid and terephthalic. The adsorption behavior of these acidic impurities has been studied through batch experiments and using UV-spectrophotometric technique. The results show that CMK-1/PDDA is very effective in selective removal of acidic compounds from PTA-waste aqueous solutions. The electrostatic interaction was considered to be the main mechanism for the adsorption of acidic compounds. The effects of chemical modification, contact time, initial concentrations, adsorbent dose, agitation speed, solution pH and reaction temperature have been optimized. The sorption equilibrium was reached within 5 min. The sorption of acidic compounds on the CMK-1/PDDA slightly decreases with increasing pH, and temperature, indicating an exothermic process. The experimental isotherm data were analyzed using the Langmuir and Freundlich equations. The equilibrium data were best represented by the Langmuir isotherm.     

Preparation, Characterization and Adsorption Performance of Cetyl Pyridine Bromide Modified Bentonites

Benzoic acid removal is important for the water treatment and adsorption is an effective treatment process. Cetyl pyridine bromide-modified bentonites (CPB-Bent) and hydroxy-aluminum-pillared bentonites (Al(OH)-Bent) were prepared and characterized by XRD, FTIR and BET. Adsorption experiments were conducted on the adsorption of benzoic acid onto natural bentonites, sodium bentonites (Na-Bent), Al(OH)-Bent and CPB-Bent in batch experiments. Benzoic acid removal onto CPB-Bent is pH dependent and the optimum adsorption is observed at pH ~3.5. The adsorption rate was fast and equilibrium was established within 90-min. The adsorption rate of benzoic acid on CPB-Bent fit a pseudo-second order kinetics model well (R ² = 0.999). The results were analyzed according to the Henry, Langmuir, Freundlich, and Dubinin-Radushkevich isotherm model equations. The adsorption data is well interpreted by the Langmuir isotherm model. Benzoic acid solution at a concentration of 0.5 mmol/L was adsorbed by CPB-Bent; and, the final adsorption efficiency was greater than 90%. The results show that benzoic acid adsorption capability of CPB-Bent is high with the maximum adsorption capability of 94.34 mg/g, which suggests that CPB-Bent is an excellent adsorbent for effective benzoic acid removal from water.     

水滑石及其焙烧产物对水中苯甲酸根的吸附研究

为了脱除水中的苯甲酸根,以苯甲酸作为吸附质,研究了水滑石及其焙烧产物的吸附作用。考察了吸附剂的镁铝摩尔比、初始pH值、苯甲酸浓度、吸附剂添加量、吸附时间和温度对吸附效果的影响,并对比考察水滑石和焙烧水滑石对苯甲酸的吸附。结果表明,水滑石及其焙烧产物对苯甲酸的最优吸附条件均为酸性环境下,镁铝摩尔比3∶1,吸附质浓度220 mg/L,吸附剂的量0.06 g;水滑石吸附时间20 h,吸附温度为60℃时,对苯甲酸的去除效果最好;而焙烧水滑石在室温下吸附苯甲酸8 h达到最高去除率;在同样条件下,水滑石焙烧产物比水滑石对苯甲酸的吸附大得多。     

Removal of fluoride from drinking water by adsorption onto alum-impregnated activated alumina

The ability of the alum-impregnated activated alumina (AIAA) for removal of fluoride from water through adsorption has been investigated in the present study. All the experiments are carried out by batch mode. The effect of various parameters viz. contact time, pH effect (pH 2–8), adsorbent dose (0.5–16 g/l), initial fluoride concentration (1–35 mg/l) has been investigated to determine the adsorption capacity of AIAA. The adsorbent dose and isotherm data are correlated to the Bradley equation. The efficacy of AIAA to remove fluoride from water is found to be 99% at pH 6.5, contact time for 3 h, dose of 8 g/l, when 20 mg/l of fluoride is present in 50 ml of water. Energy-dispersive analysis of X-ray shows that the uptake of fluoride at the AIAA/water interface is due to only surface precipitation. The desorption study reveals that this adsorbent can be regenerated following a simple base–acid rinsing procedure, however, again impregnation of the regenerated adsorbent (rinsed residue) is needed for further defluoridation process.     

The defluoridation of water by acidic alumina

Fluoride is considered as a major inorganic pollutant present in drinking water. To remove this excess fluoride, defluoridation was done by alumina. In the present study, alumina used was acidic in nature and hence considered as a good fluoride removing adsorbent. Characterization of the adsorbent was done by XRD, SEM, BET and FTIR with BET surface area of 144.27 m²/g. Systematic adsorption experiments were carried out with different process parameters such as contact time, adsorbent mass, pH, temperature and stirring speed. Fluoride adsorption by alumina was highly pH dependent. Maximum fluoride was removed from water at pH 4.4. At very low and very high pH, fluoride removal efficiency was affected. The study of thermodynamic parameters inferred that physical adsorption was dominant with activation energy of 95.13 kJ/mol and endothermic behavior of the process. The kinetics study concluded that pseudo second order kinetics was followed by the adsorption process. Adsorption equilibrium was studied with Langmuir and Freundlich isotherm models. The adsorption process followed Langmuir isotherm with an adsorption capacity of 8.4 mg/g. A regeneration study was proposed in order to reuse the adsorbent for better economy of the process. Finally, a process design calculation was reported to know the amount of adsorbent required for efficient removal of fluoride from aqueous medium.     

EFFECT OF TEMPERATURE ON THE ADSORPTION OF METHYLENE BLUE DYE ONTO SULFURIC ACID–TREATED ORANGE PEEL

The present study explains the preparation and application of sulfuric acid–treated orange peel (STOP) as a new low-cost adsorbent in the removal of methylene blue (MB) dye from its aqueous solution. The effects of temperature on the operating parameters such as solution pH, adsorbent dose, initial MB dye concentration, and contact time were investigated for the removal of MB dye using STOP. The maximum adsorption of MB dye onto STOP took place in the following experimental conditions: pH of 8.0, adsorbent dose of 0.4 g, contact time of 45 min, and temperature of 30°C. The adsorption equilibrium data were tested by applying both the Langmuir and Freundlich isotherm models. It is observed that the Freundlich isotherm model fitted better than the Langmuir isotherm model, indicating multilayer adsorption, at all studied temperatures. The adsorption kinetic results showed that the pseudo-second-order model was more suitable to explain the adsorption of MB dye onto STOP. The adsorption mechanism results showed that the adsorption process was controlled by both the internal and external diffusion of MB dye molecules. The values of free energy change (ΔG ^o) and enthalpy change (ΔH ^o) indicated the spontaneous, feasible, and exothermic nature of the adsorption process. The maximum monolayer adsorption capacity of STOP was also compared with other low-cost adsorbents, and it was found that STOP was a better adsorbent for MB dye removal.     

Removal of Fluoride from Aqueous Solution Using Aluminum-Impregnated Chitosan Biopolymer

Abstract

Aluminum impregnated chitosan (AIC) was prepared and applied as an adsorbent for the removal of fluoride from aqueous solutions. The process involved two stages: (i) isolation of chitosan from chitin, (ii) impregnation of aluminum in isolated chitosan at fixed pH. SEM and EDS techniques were used to characterize the composition of adsorbent AIC. Dynamic adsorption experiments on AIC were carried out at various pH, contact times, adsorption dosages, and initial fluoride concentration to determine optimum adsorption properties. The experimental data were analyzed using two adsorption models, Langmuir and Freundlich, with the later system providing the best fit. Thermodynamic parameters showed the adsorption process as spontaneous and endothermic. The adsorption process follows first-order kinetics for which a mechanism has been proposed. Reusability of the AIC was tested up to four consecutive cycles. The desorption experiment showed 92% elution of adsorbed fluoride at a pH of 12. Finally, the performance of the adsorbent material was studied on field water samples collected from a fluorosis endemic-region.     

Removal of toxic metal Cr(VI) from aqueous solutions using sawdust as adsorbent: Equilibrium, kinetics and regeneration studies

In the present study, a low-cost adsorbent is developed from the naturally and abundantly available sawdust which is biodegradable. The removal capacity of Cr(VI) from aqueous solutions and from the synthetically prepared industrial effluent of electroplating and tannery industries is obtained. The batch experiments are carried out to investigate the effect of the significant process parameters such as initial pH, change in pH during adsorption, contact time, adsorbent amount, and the initial Cr(VI) concentration. The maximum adsorption of Cr(VI) on sawdust is obtained at an initial pH value of 1. The value of pH increases with increase in contact time and initial Cr(VI) concentration. The equilibrium data for the adsorption of Cr(VI) on sawdust is tested with various adsorption isotherm models such as Langmuir, Freundlich, Redlich–Peterson, Koble–Corrigan, Tempkin, Dubinin–Radushkevich and Generalized equation. The Langmuir isotherm model is found to be the most suitable one for the Cr(VI) adsorption using sawdust and the maximum adsorption capacity obtained is 41.5 mg g⁻¹ at a pH value of 1. The adsorption process follows the second-order kinetics and the corresponding rate constants are obtained. Desorption of Cr(VI) from sawdust using acid and base treatment exhibited a higher desorption efficiency by more than 95%. A feasible solution is proposed, for the disposal of the contaminant (acid and base solutions) containing high concentration of Cr(VI) obtained during the desorption process. The interference of other ions which are generally present in the electroplating and tannery industrial effluent streams on the Cr(VI) removal is investigated.     

均匀设计优化油页岩原矿吸附去除水中铜离子

采用均匀设计优化实验方案并确定了油页岩吸附水中 Cu2+的最优条件.设定吸附时间(X1)、初始浓度(X2)、吸附剂投加量(X3)、溶液 pH(X4)和水浴温度(X5)为5个影响因子,通过均匀设计设定了5因素12×6×6×6×3水平的实验.逐步回归分析表明,对油页岩吸附 Cu2+有显著影响的因素依次是 pH、吸附时间、吸附剂投加量和吸附温度.初始浓度对吸附效果起负作用.极大值回归分析确定吸附的最佳条件为 pH=5.15, Cu2+初始浓度为28.49 mg/L,吸附剂投加量为0.28 g,吸附时间为162 min,吸附温度32.5℃.在此条件下,实测 Cu2+的吸附率达99%.     

Investigation of Cationic Dye Adsorption from Water onto Acetic Acid Lignin

An adsorbent was prepared from acetic acid lignin (AAL) to investigate the adsorption mechanism of methylene blue (MB) from water. AAL was first deacetylated in NaOH aqueous solution and then fractionated by methanol to prepare adsorbents with various acidic hydroxy groups. The adsorption capacities of MB increased with the increase in initial pH and with the decrease in adsorbent dosage. The results of adsorption kinetics indicated the dye uptake process is a chemisorption. The adsorption capacity of lignin for MB adsorption increased from 18.2 to 63.3 mg g^?1 as AAL was deacetylated and fractionated.     

Adsorption of humic acid onto pillared bentonite

Pillared bentonite, a clean and cost-effective adsorbent with high specific areas of 111.3 m²/g and high basalspacing of 1.98 nm, was prepared for the removal of humic acid from water. It is effective for the removal of humic acid with a high adsorption capacity of 537 mg/g, and adsorption is favored under acid conditions. Adsorption is dependent on ionic strength and dissolved NaCl enhanced adsorption. Over 97% removal was observed under natural pH conditions from humic acid solutions containing 10 mg/L Ca²⁺ or Mg²⁺, which suggests that pillared bentonite can be an effective adsorbent for the removal of humic acid for drinking water purification. Pillared bentonite can be regenerated with NaOH, and the regeneration efficiency reaches 83% and 85% when the concentration of NaOH reaches 0.025 and 0.05 mol/L. The mechanism for adsorption of humic acid to pillared bentonite is discussed.     

Sorption equilibrium of Cr(VI) ions on oak wood charcoal (Carbo Ligni) and charcoal ash as low-cost adsorbents

The aim of this study is to demonstrate the potential of oak wood charcoal (WC) and oak wood charcoal ash (WCA) as a low-cost adsorbent for environmental protection applications of Cr(VI) ion. The influence of contact time, solution pH, initial metal concentration, amount of adsorbent and ionic strength on the removal of Cr(VI) ion was studied. The adsorption of Cr(VI) with (WC) and (WCA) was investigated in a batch arrangement. The Cr(VI) ions sorbed onto the adsorbents were determined by a UV-Visible Spectrophotometer. The sorption of Cr(VI) on the adsorbent surface depends strongly on the pH and Cr(VI) ion-sorption increased with a decreasing pH until pH 2 and increase in the concentration of this metal in solution phase. The adsorption of Cr(VI) was higher between pH 2.0 and 2.5 for both adsorbents. The Freundlich adsorption isotherm was used to describe observed sorption phenomena. The maximum adsorption capacity of 30.10 mg of Cr(VI)/g for (WC) and 46.17 mg of Cr(VI)/g for (WCA) was obtained at pH of 2 and 2.5 respectively.     

Phosphate adsorption characteristics of alunite to be used as a cement additive

The adsorption of phosphate from aqueous solution by alunite has been investigated as a function of calcination temperature, particle size, pH, agitation time and initial phosphate concentration. Phosphate adsorption was seen to increase with increasing calcination temperature, decreasing adsorbent particle size and pH. The adsorption isotherm data were fitted to the Langmuir isotherm. The alunite exhibited the highest phosphate uptake capacity at 1073 K calcination temperature, at a particle size of 90-150 μm, at the initial pH of 5.0, at an equilibrium time of 60 min and at the initial phosphate concentration of 20×10⁻⁴ mol/l. The adsorption capacity, Q, was 4.697×10⁻³ mol/g at initial pH 5.0.     

Copper and zinc sorption by treated oil shale ash

Jordanian oil shale ash was used as an adsorbent for the removal of copper and zinc from aqueous solution. This ash was treated with either hydrochloric, nitric, sulfuric or phosphoric acids followed by washing and/or neutralization with sodium hydroxide in order to enhance its adsorption capacity. The sample that was treated with nitric acid showed the highest cation exchange capacity (CEC) of 146 meq/100 g, while the one that was treated with sulfuric acid showed a value of 32 meq/100 g. Different adsorption isotherm data for both copper and zinc were obtained using the nitric acid-treated sample at different pH values. Freundlich and BET models were used to fit the experimental data, which showed that BET best-fitted these data. The separation factor for these isotherms shows unfavorable adsorption type at lower pH value.     

Adsorption study of hexavalent chromium using tamarind hull-based adsorbents

The adsorption characteristics of hexavalent chromium was studied with an adsorbent developed from waste tamarind hull. Experiments were conducted in batch mode to observe the influence of different parameters such as initial concentration of metal ions, adsorbent dosage, adsorbent particle size, stirrer speed, temperature and pH of the solution. Acidic pH strongly favored the adsorption. With decreasing the pH of the solution from 5.0 to 1.0, the removal of chromium was enhanced from 33% to 99%. The adsorption process was found to follow a pseudo-first-order rate mechanism and the rate constant was evaluated at 30 °C. The Freundlich, Redlich–Peterson and the Fritz–Schlunder isotherm fit the equilibrium data satisfactorily. Adsorption of chromium was found to increase with increase in the process temperature. Using an adsorbent dosage of 1.0 g/L and an acidic pH (2.0), the equilibrium adsorption capacity of the prepared adsorbent was found to be about 70 mg/g at 30 °C, which increased to about 81 mg/g at 50 °C. The entropy change, free energy change and heats of adsorption were determined for the process.     

Preparation and characterization of an IPN type chelating resin containing amino and carboxyl groups for removal of Cu(II) from aqueous solutions

A novel IPN type chelating resin, amino-functionalized poly (glycidyl methacrylate)/poly (acrylic acid), (pGMA/pAA), was synthesized by a combination of serial reactions including, conventional radical polymerization, amination and photopolymerization. To assess the efficacy and characteristics of the resin in removal of Cu (II), batch adsorption experiments were carried out, and the effects of different parameters such as contact time, adsorbent dosage, initial metal ion concentration, temperature, and pH on the adsorption process were investigated. The results showed that 0.5 g/L dosage and pH 5 are the optimum values to achieve the maximum adsorption capacity and the adsorption kinetic of Cu (II) was well represented by pseudo-second-order kinetic model. In addition, it was found that the adsorption was mainly controlled by the film diffusion mechanism, along with a considerable contribution of the intra-particle diffusion mechanism, and Langmuir, Freundlich and Dubinin–Radushkevich (D–R) isotherm models can be used for interpreting the adsorption process. Moreover, FT-IR analysis results and the mean free energies of adsorption clearly indicate that the ion exchange and chelation mechanisms took place as dominating mechanisms simultaneously during the adsorption process. It was also found to be that IPN resin could be used at least four times without losing its original activity.     

Synthesis of a novel functional group-bridged magnetized bentonite adsorbent:Characterization,kinetics, isotherm,thermodynamics and regeneration

A novel magnetic adsorbent was synthesized by magnetizing bentonite by APTES-Fe_3O_4 via a functional groupbridged interaction. The characterization of APTES-Fe_3O_4/bentonite was conducted via transmission electron microscope(TEM), X-ray diffraction(XRD), Fourier transform infrared spectrophotometer(FT-IR), thermal gravimetric analysis(TGA), vibrating sample magnetometer(VSM), zeta potential analysis and Brunner–Emmet–Teller(BET). The APTES-Fe_3O_4/bentonite was assessed as adsorbents for methylene blue(MB) with a high adsorption capacity(91.83 mg·g~(-1)). Factors affecting the adsorption of MB(such as p H, equilibrium time, temperature and initial concentration) were investigated. The adsorption process completely reaches equilibrium after 120 min and the maximum sorption is achieved at p H 8.0. The adsorption trend follows the pseudosecond order kinetics model. The adsorption data gives good fits with Langmuir isotherm model. The parameter factor RLfalls between 0 and 1, indicating the adsorption of MB is favorable. The adsorption process is endothermic with positive ΔH~0 values. The positive values of ΔG~0 confirm the affinity of the adsorbent towards MB, and suggest an increased randomness at the solid–liquid interface during the adsorption process. Regeneration of the saturated adsorbent was easily carried out via gamma-irradiation.