Optical thermophysical characteristics of the condensed phase of combustion products and heatproof materials

An unconventional unit for experimentally studying the optical thermophysical properties of materials over a wide temperature range is described. Results are presented of studying the temperature function and dispersion of the absorption index for the condensed phase of the combustion products of a metalbearing fuel and of the emittance of fiber fireproof materials.Notation K spectral absorption coefficient - D spectral transmission coefficient - spectral absorption index - wavelength - d sample thickness - d_s surface layer thickness - I spectral intensity of radiation - , spectral and total emittances Kirov Polytechnical Institute. Kazan Chemical Engineering Institute, Russia. Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 64, No. 3, pp. 330–336. March, 1993     

A note on the similarity solutions for free convection on a vertical plate

Summary The similarity solutions for free convection on a vertical plate when the (non-dimensional) plate temperature is x and when the (non-dimensional) surface heat flux is –x are considered. Solutions valid for 1 and 1 are obtained. Further, for the first problem it is shown that there is a value ₀, dependent on the Prandtl number, such that solutions of the similarity equations are possible only for >₀, and for the second problem that solutions are possible only for >–1 (for all Prandtl numbers). In both cases the solutions becomes singular as ₀ and as –1, and the natures of these singularities are discussed.     

The athermal α → ω transformation in Zr-2 at% Nb alloy

The athermal transformation in Zr-2 at.% Nb alloy has been investigated by transmission electron microscopy. Analysis of the selected-area diffraction pattern has shown that the orientation relationships between the omega and the parent-phase in quenched Zr-2 at.% Nb alloy are the same as have been previously observed for the reaction in pure zirconium. Thus it was deduced that the direct transition has taken place in the alloy during cooling. The-originated -particles were visualized using the dark-field technique. The formation of the athermal omega in the-region of-stabilized Zr-Nb alloy is discussed in terms of the relative positions of the free energy equilibrium curvesT ₀ ,T ₀ ,T ₀ and the correspondingM _s ,M _s andT _s start curves. It is concluded that the omega phase can occur over a much wider range of alloy compositions than is usually recognized on the basis of transformation data.     

Microstructure and mechanical properties of rapidly quenched L20 and L20+L12 alloys in Ni-Al-Fe and Ni-Al-Co systems

Ductile L2₀-type wires and+L1₂-type duplex wires with high strengths and large elongation in the Ni-Al-Fe and Ni-Al-Co ternary systems have been manufactured directly from the liquid state by an in-rotating-water spinning method. The wire diameter was in the range 80 to 180m and the average grain size was 2 to 4m for the wires and 0.2 to 1.0m for the+ wires. _y, _f and _p of the wires were found to be about 360 to 760 MPa, 560 to 960 MPa, and 0.2 to 5.5%, respectively, for the Ni-Al-Fe system, those of the+ wires were about 395 to 660 MPa, 670 to 1285 MPa, and 3.5 to 17%, respectively, for the Ni-Al-Fe system, and about 260 to 365 MPa, 600 to 870 MPa, and 4.0 to 7.0%, respectively, for the Ni-Al-Co system. Cold-drawing caused a significant increase in _y and _f and the values attained were about 1850 and 2500 MPa, respectively, for Ni-20Al-30Fe and Ni-25Al-30Co wires drawn to about 90% reduction in area. The high strengths, large elongation and good cold-workability of the melt-quenched and+ compound wires have been inferred to be due to the structural change into a low-degree ordered state containing a high density of phase boundaries, suppression of grain-boundary segregation and refinement of grain size.     

A linear differential equation with a time-periodic damping coefficient: stability diagram and an application

In this paper the second-order differential equation with time-dependent damping coefficientx + cos (2t) x + x = 0,will be studied. In particular the coexistence of periodic solutions corresponding with the vanishing of domains of instability is investigated. The coexistence of -periodic solutions occurs for 4n ² where n is integer. This implies that the instability area which is emanating from =4n ² in the – stability diagram disappears. In applications, this equation can be considered as a model equation for the study of rain-wind-induced vibrations of a special oscillator.on leave as a PhD reseacher at Delft University of Technology, The Netherlands     

Magnetic field dependence of zero-sound attenuation close to the pair-breaking edge in3He-B due toJ=1−,J z =±1 collective modes

Our previous theory yielded for the Zeeman splitting of the imaginaryJ=1 collective mode in³He-B the result =2+0.25J _z ( is the effective Larmor frequency). In this paper we take into account the downward shift of the pair-breaking edge from 2 to 2₂– (₂ and ₁ are the longitudinal and transverse gap parameters). This leads to a complex Landé factor: the frequencies of theJ _z =±1 components become =2+0.39J _z , and the linewidths of these resonances become finite: =0.18. The coupling amplitudes of theJ _z =±1 components to density are found to be proportional to gap distortion, (₁–₂/(/)². Our results for the ultrasonic attenuation due to theJ _z =±1,J=1 modes are capable of explaining the field dependence of the attenuation close to the pair-breaking edge as observed by Dobbs, Saunders, et al. The observed peak is caused by theJ _z =–1 component: its height increases due to gap distortion as the field is increased, and the peak shifts downward in temperature and its width increases with the field due to the complex Landé factor. TheJ _z =+1 component gives rise to a corresponding dip relative to the continuum attenuation.     

Interaction between a dislocation and an impurity in KCl: Mg2+ single crystals

The interaction between a dislocation and the impurity in KCl: Mg²⁺ (0.035 mol% in the melt) was investigated at 77–178 K with respect to the two models: one is the Fleischer's model and the other the Fleischer's model taking account of the Friedel relation. The latter is termed the F-F. The dependence of strain-rate sensitivity due to the impurities on temperature for the specimen was appropriate to the Fleischer's model than the F-F. Furthermore, the activation enthalpy, H, for the Fleischer's model appeared to be nearly proportional to the temperature in comparison with the F-F. The Friedel relation between effective stress and average length of the dislocation segments is exact for most weak obstacles to dislocation motion. However, above-mentioned results mean that the Friedel relation is not suitable for the interaction between a dislocation and the impurity in the specimen. Then, the value of H(T _c) at the Fleischer's model was found to be 0.61 eV. H(T _c) corresponds to the activation enthalpy for overcoming of the strain field around the impurity by a dislocation at 0 K. In addition, the Gibbs free energy, G ₀, concerning the dislocation motion was determined to be between 0.42 and 0.48 eV on the basis of the following equation ln / = G ₀/(kT_p0)1 – (T/T _c)^{1/2 –1}(T/T _c)^1/2 + ln ₀/where k is the Boltzmann's constant, T the temperature, T _c the critical temperature at which the effective stress due to the impurities is zero, _p0 the effective shear stress without thermal activation, and ₀ the frequency factor.     

Some expectation on the mechanism of cross-flow instability in a swept wing flow

Summary Three-dimensional boundary layer transition on axisymmetric rotating bodies is the subject of a comprehensive experimental study. Based on this study, hypotheses are made on the mechanism of cross-flow instability for swept wing flow. These new results are combined with past explanations to provide a rough sketch for the entire flow field over the swept wing. From this new viewpoint there appears the mechanism of traveling waves, being induced by a stationary disturbance. Some uncertainties appearing in recent papers concerning this flow field are discussed. Among these uncertainties for which an explanation is provided, is the discrepancy of frequencies between the hot wire signal and the visualized flow pattern.Nomenclature x direction along a potential flow stream line - y direction normal to a potential flow stream line - z direction normal to bothx andy directions - U mean velocity inx-direction - V mean velocity iny-direction - x direction along a disturbance - y direction normal tox direction - u, v, w fluctuating velocity components inx, y, z directions - U velocity inx-direction with wall fixed coordinate - U _e velocity of outer edge of boundary-layer - U uniform flow velocity normal to leading edge - V uniform flow velocity parallel to leading edge - Q upstream velocity - N rotation speed of an axisymmetric body - P arbitrary point on a disk surface - r radius to a pointP - R ₀ radius of a disk or a cylinder - U _p phase velocity of ring like vortices - T position where wall streaks appear in the case of oil flow visualization - Re _c,t critical and transitional Reynolds numbers - angle of the spiral disturbance - boundary-layer thickness - angular velocity - sweep angle of a body - wave length of disturbance - kinematic viscosity of a fluid With 11 Figures     

Theory of RF SQUIDs Operating in the Presence of Large Thermal Fluctuations

A comprehensive analytical theory is presented for non-hysteretic RF SQUIDs operating in the adiabatic mode in the presence of large thermal fluctuations. When 1 ( = 2LI_c/₀ is the hysteresis parameter, L is the SQUID inductance, I_c is the critical current of the Josephson junction, and ₀ is the flux quantum) the theory is applicable also for RF SQUIDs operating in the non-adiabatic mode. In contrast to previous theories in which the noise is treated perturbatively and which therefore are applicable only if the product 1 ( = 2k_BT/ ₀ I_c is the noise parameter, k_B is the Boltzmann constant, and T is the absolute temperature)—the case of small thermal fluctuations—the present theory is valid for around unity or higher. In the limit 0 the theory reproduces the results of small thermal fluctuations theories. It has been found that in the presence of large thermal fluctuations the screening current in the SQUID inductance is suppressed by a factor that increases with increasing . Taking into account this new basic fact, all SQUID characteristics (output signal, transfer function, noise spectral density and energy sensitivity) have been recalculated and a good agreement with experimental data has been obtained. It has been also found that RF SQUIDs can be operated with substantially higher values of the inductance and of the noise parameter than DC SQUIDs. These two aspects, which are of particular importance at liquid nitrogen temperature, make high T_c RF SQUIDs very attractive.     

Thermal Expansion and Isothermal Compressibility of TlIn1 – xNdxSe2 (0 ≤ x≤ 0.08) Crystals

The thermal expansion coefficient () and isothermal compressibility ( _T ) of TlIn_{1 – x} Nd _x Se₂(0 x 0.08) crystals were measured between 77 and 400 K. In the range 77–160 K, both and _T increase with temperature, the increase in being much steeper. At higher temperatures, and _T change very little. The observed composition dependences of and _T are interpreted in terms of energy-band structure.     

Martensitic transformations in Ti-Mo alloys

A detailed investigation has been made of the structure of alloys of the Ti-Mo system containing up to 10wt% Mo, water-quenched from the-phase region. With increase in molybdenum content, the martensite structure changes from hexagonal () to orthorhombic () at 4 wt% Mo, and at 10 wt% Mo, the structure is completely retained . For alloy compositions <4 wt% Mo, there is a diffusional component in the transformation of the -phase at the quench rates employed. There is a transition, with increase in molybdenum content, in morphology (from massive to acicular) and in substructure (from dislocations to twins). However, the transitions in crystallography, morphology and sub-structure are not directly related to one another except for an abrupt loss of dislocation substructure at the/ transition. The to crystallographic transition has the characteristics of a second order transformation, and evidence has been obtained of the existence of a spinodal within the metastable orthorhombic system. The orthorhombic martensites of Ti-6 and 8 wt% Mo decompose during quenching producing a fine modulated structure within the martensite plates, consistent with a proposed spinodal mode of decomposition.     

Convection in a shallow laterally heated cavity with conducting boundaries

Shallow cavity flows driven by horizontal temperature gradients are analysed over a range of Rayleigh numbersR and Prandtl numbers , whereR is comparable in size to the aspect ratioL(1). Eigenvalue calculations show the existence of a critical Prandtl number R > R _c (), below which the parallel core-flow structure is destroyed for Rayleigh numbersR>R _c(). For other Rayleigh numbers and Prandtl numbers the horizontal scale of influence of the end walls of the cavity is determined.     

Surface tension of helium at the superfluid critical end-point

The singularity in the vapor-liquid interfacial tension, (T), of helium at the transition to superfluidity is analyzed theoretically. The universal amplitude ratio R ⁺ =K₊( ₀ ⁺ )^d–1/k _B T , where K₊ and K_– are the amplitudes of the |T–T|^µ singularity in , with =1.34 ₃ , is known from recent work to first order in =4–d for the general n-vector model in d dimensions. Extrapolation to d=3 for n=2 indicates R ⁺ =0.05–0.08, which is shown to be consistent with the experimental data. Further analysis of the experiments establishes that the universal ratio Q=K₊/K _– exceeds 0.35, and is consistent with the recent prediction Q0.9; this demonstrates the inadequacies of earlier theoretical treatments. The existence in the observed surface tension of an anomalous, negative contribution of unknown origin at a few millikelvin beneath T is stressed.     

The influence of antimony-additions on the creep behaviour of a 25wt% Cr-20wt% Ni austenitic stainless steel

The effect of antimony on the creep behaviour (dislocation creep) of a 25 wt% Cr-20 wt% Ni stainless steel with ~ 0.005 wt% C was studied with a view to assessing the segregation effect. The antimony content of the steel was varied up to 4000 ppm. The test temperature range was 1153 to 1193 K, the stress range, 9.8 to 49.0 MPa, and the grain-size range, 40 to 600m. The steady state creep rate, , decreases with increasing antimony content, especially in the range of intermediate grain sizes (100 to 300m). Stress drop tests were performed in the secondary creep stages and the results indicate that antimony causes dislocations in the substructure to be immobile, probably by segregating to them, reducing the driving stress for creep.Nomenclature _a Creep stress in a constant load creep test without stress-drop - _A Initial applied stress in stress-drop tests - Stress decrement - ( _A-) Applied stress after a stress decrement, - t _i Incubation time after stress drop (by the positive creep) - _C Strain-arrest stress - _i Internal stress - _{s s}-component (= _i- _c) - Steady state creep rate (average value) in a constant load creep test - Strain rate at time,t, in a constant load creep test - New steady state creep rate (average value) after stress drop from _A to ( _A-) - Strain rate at time,t, after stress drop.     

Thermal transport properties of helium near the superfluid transition. II. Dilute3He-4He mixtures in the superfluid phase

Measurements of the average thermal conductivity _exp hQ/T and of the thermal relaxation time to reach steady-state equilibrium conditions are reported in the superfluid phase for dilute mixtures of³He in⁴He. Hereh is the cell height,Q is the heat flux, andT is the temperature difference across the fluid layer. The measurements were made over the impurity range 2×10^–9<X(³He)<3×10^–2 and with heat fluxes 0.3<Q<160 µW/cm². Assuming the boundary resistanceR _b , measured forX<10^–5, to be independent ofX over the whole range ofX, a calculation is given for _exp. ForQ smaller than a well-defined critical heat fluxQ _c (X) X ^0.9, _exp is independent of Q and can be identified with the local conductivity _eff, which is found to be independent of the reduced temperature = (T–T)/T for –10^–2. Its extrapolated value at T is found to depart forX10^–3 from the prediction X ^–1 , tending instead to a weaker divergence X ^–a witha0.08. A finite conductivity asX tends to zero is not excluded by the data, however. ForQ >Q _c (X), a nonlinear regime is entered. ForX10^–6, the measurements with the available temperature resolution are limited to the nonlinear conditions, but can be extrapolated into the linear regime forX2×10^–7. The results for _exp(Q),Q _c (X), and _eff(XX) are found to be internally consistent, as shown by comparison with a theory by Behringer based on Khalatnikov's transport equations. Furthermore, the observed relaxation times (X) in the linear regime are found to be consistent forX>10^–5 with the hydrodynamic calculations using the measured _eff(X). ForX<10^–5, a faster relaxation mechanism than predicted seems to dominate. The transport properties in the nonlinear regimes are presented and unexplained observations are discussed.     

Dislocation structures in Zr3Al-based alloys

Transmission electron microscopy has been used to investigate dislocation structures in deformed binary and ternary Zr₃Al-based alloys. In the binary alloy deformed at temperatures between 293 and 673 K the dislocations in the Zr₃Al phase consisted of a/31 1 2-type partial dislocations bounding superlattice intrinsic stacking fault on {1 1 1} planes. The {111} a/31 1 ¯2 stacking fault energy was approximately 2mJ m^–2 at 673 K. In binary specimens deformed between 873 and 1073 K cube slip predominated. Dislocations consisted mainly of a/2 1 1 0 pairs separated by antiphase boundary. For this temperature range the {1 0 0} a/201 1 antiphase boundary energy was between 30 and 45 mJ m^–2. Alloying with niobium or titanium was found to increase the {111} a/31 1¯2 stacking fault energy and thus increase the propensity for antiphase boundary-type dissociation.     

The thermal conductivity of AISI 304L stainless steel

A compilation and critical analysis of the thermal conductivity () of AISI 304 stainless steel (SS) between 100 and 1707 K has been given in the literature. The author represented his recommended values of by an inflection in the A versus temperature relationship between 300 and 500 K. Because a physical mechanism had not been identified that would produce such a temperature dependence in of 304 SS, interest was generated in the possible existence of an as yet undiscovered phenomenon that might cause such an inflection. Consequently, experimental verification of the inflection was sought. The present paper presents recent measurements of , the electrical resistivity, and the absolute Seebeck coefficient of 304L SS from 300 to 1000 K and of the thermal diffusivity () from 297 to 423 K. The values computed from the a measurements were within ± 1.6% of the directly measured An inflection was not observed in the temperature dependence of between 300 and 500 K. After careful evaluation and because a physical mechanism still has not been identified which would produce such an inflection, the authors conclude that the inflection in the vs T relationship reported in the literature was caused by the data analysis technique.     

Anisotropic Pair-breaking by Impurity Doping in High-Tc Cuprates: Modification of Interlayer Coupling

Impurity (Zn/Ni) doping effects on the superconducting coherence length and the penetration depth have been studied for the in-plane and the out-of-plane directions of YBa ₂ Cu ₃ O _y single crystals. We determined from diamagnetic susceptibility in the reversible region and from optical conductivity spectra. It was found that both in and the ac-anisotropy ratio is reduced with impurity doping. Both changes can be explained by assuming an increase in Josephson coupling strength due to impurity doping.     

McMillan tunneling model of the superconducting proximity effect. Specific heat jump

The McMillan tunneling model of the superconducting proximity effect has been used to calculate the specific heat jumps on the S side and on the N side of a proximity composite. The case of the BCS interaction constant on the N side, _N being identically zero and the case _N 0 have both been studied. The detailed dependence of the normalized specific heat jumps on the McMillan parameters _S and _N and on the transition temperature of the composite has been computed. A reasonable agreement between our theoretical values and recent experimental data of Bevolo et al. is obtained.Work supported in part by a grant from the Natural Sciences and Engineering Research Council of Canada.     

Effect of phase fluctuations upon penetration depth

The temperature dependence of the static penetration (T) has been used as a guide to the nature of the superconducting state in high-T _c materials. It has been argued that an algebraic temperature dependence in the ratio (T)/(0) [(T) — (0)]/(0) at low temperature is evidence for d-wave pairing. This paper examines the effect of superconducting phase fluctuations upon (T) and finds an algebraic dependence over a broad range of temperature.