Ternary Organic Solar Cells with Efficiency >16.5% Based on Two Compatible Nonfullerene Acceptors

A ternary structure has been demonstrated as being an effective strategy to realize high power conversion efficiency (PCE) in organic solar cells (OSCs); however, general materials selection rules still remain incompletely understood. In this work, two nonfullerene small‐molecule acceptors 3TP3T‐4F and 3TP3T‐IC are synthesized and incorporated as a third component in PM6:Y6 binary blends. The photovoltaic behaviors in the resultant ternary OSCs differ significantly, despite the comparable energy levels. It is found that incorporation of 15% 3TP3T‐4F into the PM6:Y6 blend results in facilitating exciton dissociation, increasing charge transport, and reducing trap‐assisted recombination. All these features are responsible for the enlarged PCE of 16.7% (certified as 16.2%) in the PM6:Y6:3TP3T‐4F ternary OSCs, higher than that (15.6%) in the 3TP3T‐IC containing ternary devices. The performance differences are mainly ascribed to the compatibility between the third component and the host materials. The 3TP3T‐4F guest acceptor exhibits an excellent compatibility with Y6, tending to form well‐mixed phases in the ternary blend without disrupting the favored bicontinuous transport networks, whereas 3TP3T‐IC displays a morphological incompatibility with Y6. This work highlights the importance of considering the compatibility for materials selection toward high‐efficiency ternary organic OSCs.     

Over 14% Efficiency in Organic Solar Cells Enabled by Chlorinated Nonfullerene Small‐Molecule Acceptors

To make organic solar cells (OSCs) more competitive in the diverse photovoltaic cell technologies, it is very important to demonstrate that OSCs can achieve very good efficiencies and that their cost can be reduced. Here, a pair of nonfullerene small‐molecule acceptors, IT‐2Cl and IT‐4Cl, is designed and synthesized by introducing easy‐synthesis chlorine substituents onto the indacenodithieno[3,2‐b]thiophene units. The unique feature of the large dipole moment of the C? Cl bond enhances the intermolecular charge‐transfer effect between the donor–acceptor structures, and thus expands the absorption and down shifts the molecular energy levels. Meanwhile, the introduction of C? Cl also causes more pronounced molecular stacking, which also helps to expand the absorption spectrum. Both of the designed OSCs devices based on two acceptors can deliver a power conversion efficiency (PCE) greater than 13% when blended with a polymer donor with a low‐lying highest occupied molecular orbital level. In addition, since IT‐2Cl and IT‐4Cl have very good compatibility, a ternary OSC device integrating these two acceptors is also fabricated and obtains a PCE greater than 14%. Chlorination demonstrates effective ability in enhancing the device performance and facile synthesis route, which both deserve further exploitation in the modification of photovoltaic materials.     

Two Well‐Miscible Acceptors Work as One for Efficient Fullerene‐Free Organic Solar Cells

High‐performance ternary organic solar cells are fabricated by using a wide‐bandgap polymer donor (bithienyl‐benzodithiophene‐alt‐fluorobenzotriazole copolymer, J52) and two well‐miscible nonfullerene acceptors, methyl‐modified nonfullerene acceptor (IT‐M) and 2,2′‐((2Z ,2′Z )‐((5,5′‐(4,4,9,9‐tetrakis(4‐hexylphenyl)‐4,9‐dihydros‐indaceno[1,2‐b :5,6‐b ′]dithiophene‐2,7‐diyl)bis(4‐((2‐ethylhexyl)oxy)thiophene‐5,2‐diyl))bis(methanylylidene))bis(3‐oxo‐2,3‐dihydro‐1H ‐indene‐2,1‐diylidene))dimalononitrile (IEICO). The two acceptors with complementary absorption spectra and similar lowest unoccupied molecular orbital levels show excellent compatibility in the blend due to their very similar chemical structures. Consequently, the obtained ternary organic solar cells (OSC) exhibits a high efficiency of 11.1%, with an enhanced short‐circuit current density of 19.7 mA cm^?2 and a fill factor of 0.668. In this ternary system, broadened absorption, similar output voltages, and compatible morphology are achieved simultaneously, demonstrating a promising strategy to further improve the performance of ternary OSCs.     

A Tandem Organic Solar Cell with PCE of 14.52% Employing Subcells with the Same Polymer Donor and Two Absorption Complementary Acceptors

The tandem structure is an efficient way to simultaneously tackle absorption and thermalization losses of the single junction solar cells. In this work, a high‐performance tandem organic solar cell (OSC) using two subcells with the same donor poly[(2,6‐(4,8‐bis(5‐(2‐ethylhexyl)thiophen‐2‐yl)‐benzo[1,2‐b:4,5‐b′]dithiophene))‐alt‐(5,5‐(1′,3′‐di‐2‐thienyl‐5′,7′‐bis(2‐ethylhexyl)benzo[1′,2′‐c:4′,5′‐c′]dithiophene‐4,8‐dione))] (PBDB‐T) and two acceptors, F‐M and 2,9‐bis(2‐methylene‐(3(1,1‐dicyanomethylene)benz[f ]indanone))7,12‐dihydro‐(4,4,10,10‐tetrakis(4‐hexylphenyl)‐5,11‐diocthylthieno[3′,2′:4,5]cyclopenta[1,2‐b]thieno[2″,3″:3′,4′]cyclopenta[1′,2′:4,5]thieno[2,3‐f][1]benzothiophene (NNBDT), with complementary absorptions is demonstrated. The two subcells show high V_oc with value of 0.99 V for the front cell and 0.86 V for the rear cell, which is the prerequisite for obtaining high V_oc of their series‐connected tandem device. Although there is much absorption overlap for the subcells, a decent J_sc of the tandem cell is still obtained owing to the complementary absorption of the two acceptors in a wide range. With systematic device optimizations, a best power conversion efficiency of 14.52% is achieved for the tandem device, with a high V_oc of 1.82 V, a notable FF of 74.7%, and a decent J_sc of 10.68 mA cm^?2. This work demonstrates a promising strategy of fabricating high‐efficiency tandem OSCs through elaborate selection of the active layer materials in each subcell and tradeoff of the V_oc and J_sc of the tandem cells.     

Recent Progress in Molecular Design of Fused Ring Electron Acceptors for Organic Solar Cells

The quest for sustainable energy sources has led to accelerated growth in research of organic solar cells (OSCs). A solution‐processed bulk‐heterojunction (BHJ) OSC generally contains a donor and expensive fullerene acceptors (FAs). The last 20 years have been devoted by the OSC community to developing donor materials, specifically low bandgap polymers, to complement FAs in BHJs. The current improvement from ≈2.5% in 2013 to 17.3% in 2018 in OSC performance is primarily credited to novel nonfullerene acceptors (NFA), especially fused ring electron acceptors (FREAs). FREAs offer unique advantages over FAs, like broad absorption of solar radiation, and they can be extensively chemically manipulated to tune optoelectronic and morphological properties. Herein, the current status in FREA‐based OSCs is summarized, such as design strategies for both wide and narrow bandgap FREAs for BHJ, all‐small‐molecule OSCs, semi‐transparent OSC, ternary, and tandem solar cells. The photovoltaics parameters for FREAs are summarized and discussed. The focus is on the various FREA structures and their role in optical and morphological tuning. Besides, the advantages and drawbacks of both FAs and NFAs are discussed. Finally, an outlook in the field of FREA‐OSCs for future material design and challenges ahead is provided.     

Eco‐Compatible Solvent‐Processed Organic Photovoltaic Cells with Over 16% Efficiency

Recent advances in nonfullerene acceptors (NFAs) have enabled the rapid increase in power conversion efficiencies (PCEs) of organic photovoltaic (OPV) cells. However, this progress is achieved using highly toxic solvents, which are not suitable for the scalable large‐area processing method, becoming one of the biggest factors hindering the mass production and commercial applications of OPVs. Therefore, it is of great importance to get good eco‐compatible processability when designing efficient OPV materials. Here, to achieve high efficiency and good processability of the NFAs in eco‐compatible solvents, the flexible alkyl chains of the highly efficient NFA BTP‐4F‐8 (also known as Y6) are modified and BTP‐4F‐12 is synthesized. Combining with the polymer donor PBDB‐TF, BTP‐4F‐12 shows the best PCE of 16.4%. Importantly, when the polymer donor PBDB‐TF is replaced by T1 with better solubility, various eco‐compatible solvents can be applied to fabricate OPV cells. Finally, over 14% efficiency is obtained with tetrahydrofuran (THF) as the processing solvent for 1.07 cm² OPV cells by the blade‐coating method. These results indicate that the simple modification of the side chain can be used to tune the processability of active layer materials and thus make it more applicable for the mass production with environmentally benign solvents.     

Efficient Organic Solar Cells with Non‐Fullerene Acceptors

Fullerene‐free OSCs employing n‐type small molecules or polymers as the acceptors have recently experienced a rapid rise with efficiencies exceeding 12%. Owing to the good optoelectronic and morphological tunabilities, non‐fullerene acceptors exhibit great potential for realizing high‐performance and practical OSCs. In this Review, recent exciting progress made in developing highly efficient non‐fullerene acceptors is summarized, mainly correlating factors like absorption, energy loss and morphology of new materials to their correspondent photovoltaic performance.     

16.67% Rigid and 14.06% Flexible Organic Solar Cells Enabled by Ternary Heterojunction Strategy

Ternary heterojunction strategies appear to be an efficient approach to improve the efficiency of organic solar cells (OSCs) through harvesting more sunlight. Ternary OSCs are fabricated by employing wide bandgap polymer donor (PM6), narrow bandgap nonfullerene acceptor (Y6), and PC₇₁BM as the third component to tune the light absorption and morphologies of the blend films. A record power conversion efficiency (PCE) of 16.67% (certified as 16.0%) on rigid substrate is achieved in an optimized PM6:Y6:PC₇₁BM blend ratio of 1:1:0.2. The introduction of PC₇₁BM endows the blend with enhanced absorption in the range of 300–500 nm and optimises interpenetrating morphologies to promote photogenerated charge dissociation and extraction. More importantly, a PCE of 14.06% for flexible ITO‐free ternary OSCs is obtained based on this ternary heterojunction system, which is the highest PCE reported for flexible state‐of‐the‐art OSCs. A very promising ternary heterojunction strategy to develop highly efficient rigid and flexible OSCs is presented.     

Two Well‐Compatible Acceptors with Efficient Energy Transfer Enable Ternary Organic Photovoltaics Exhibiting a 13.36% Efficiency

Organic photovoltaics (OPVs) are fabricated with PM6 as donor and T6Me, IT‐2F, or their mixture as acceptor. A 13.36% power conversion efficiency (PCE) is achieved from the optimized ternary OPVs with 50 wt% IT‐2F in acceptors, which is attributed to the enhanced photon harvesting of ternary active layers and improved exciton utilization efficiency through energy transfer from IT‐2F to T6Me. The efficient energy transfer from IT‐2F to T6Me can be confirmed from the photoluminescence spectra of neat and blend films, which may provide additional channels to enhance exciton utilization efficiency for achieving short‐circuit current density (J_SC) improvement of ternary OPVs. It should be highlighted that the fill factor (FF) of ternary OPVs can be monotonously increased along with the incorporation of IT‐2F, indicating the gradually optimized phase separation degree of ternary active layers. The third component IT‐2F plays a key role in optimizing phase separation as a morphology regulator. Over 8% PCE improvement is achieved in the optimized ternary OPVs compared with the over 12% PCEs of the corresponding binary OPVs, respectively. This work indicates that the performance of ternary OPVs can be well optimized by carefully picking materials with good compatibility and complementary absorption spectra, as well as the appropriate energy levels.     

Morphology Control Enables Efficient Ternary Organic Solar Cells

Ternary organic solar cells are promising alternatives to the binary counterpart due to their potential in achieving high performance. Although a growing number of ternary organic solar cells are recently reported, less effort is devoted to morphology control. Here, ternary organic solar cells are fabricated using a wide‐bandgap polymer PBT1‐C as the donor, a crystalline fused‐ring electron acceptor ITIC‐2Cl, and an amorphous fullerene derivative indene‐C₆₀ bisadduct (ICBA) as the acceptor. It is found that ICBA can disturb π–π interactions of the crystalline ITIC‐2Cl molecules in ternary blends and then help to form more uniform morphology. As a result, incorporation of 20% ICBA in the PBT1‐C:ITIC‐2Cl blend enables efficient charge dissociation, negligible bimolecular recombination, and balanced charge carrier mobilities. An impressive power conversion efficiency (PCE) of 13.4%, with a high fill factor (FF) of 76.8%, is eventually achieved, which represents one of the highest PCEs reported so far for organic solar cells. The results manifest that the adoption of amorphous fullerene acceptor is an effective approach to optimizing the ternary blend morphology and thereby increases the solar cell performance.     

Enhanced and Balanced Charge Transport Boosting Ternary Solar Cells Over 17% Efficiency

Ternary architecture is one of the most effective strategies to boost the power conversion efficiency (PCE) of organic solar cells (OSCs). Here, an OSC with a ternary architecture featuring a highly crystalline molecular donor DRTB-T-C4 as a third component to the host binary system consisting of a polymer donor PM6 and a nonfullerene acceptor Y6 is reported. The third component is used to achieve enhanced and balanced charge transport, contributing to an improved fill factor (FF) of 0.813 and yielding an impressive PCE of 17.13%. The heterojunctions are designed using so-called pinning energies to promote exciton separation and reduce recombination loss. In addition, the preferential location of DRTB-T-C4 at the interface between PM6 and Y6 plays an important role in optimizing the morphology of the active layer.     

Subtle Molecular Tailoring Induces Significant Morphology Optimization Enabling over 16% Efficiency Organic Solar Cells with Efficient Charge Generation

Manipulating charge generation in a broad spectral region has proved to be crucial for nonfullerene-electron-acceptor-based organic solar cells (OSCs). 16.64% high efficiency binary OSCs are achieved through the use of a novel electron acceptor AQx-2 with quinoxaline-containing fused core and PBDB-TF as donor. The significant increase in photovoltaic performance of AQx-2 based devices is obtained merely by a subtle tailoring in molecular structure of its analogue AQx-1. Combining the detailed morphology and transient absorption spectroscopy analyses, a good structure–morphology–property relationship is established. The stronger π–π interaction results in efficient electron hopping and balanced electron and hole mobilities attributed to good charge transport. Moreover, the reduced phase separation morphology of AQx-2-based bulk heterojunction blend boosts hole transfer and suppresses geminate recombination. Such success in molecule design and precise morphology optimization may lead to next-generation high-performance OSCs.     

Nonfullerene Tandem Organic Solar Cells with High Performance of 14.11%

Fabricating solar cells with tandem structure is an efficient way to broaden the photon response range without further increasing the thermalization loss in the system. In this work, a tandem organic solar cell (TOSC) based on highly efficient nonfullerene acceptors (NFAs) with series connection type is demonstrated. To meet the different demands of front and rear sub‐cells, two NFAs named F‐M and NOBDT with a whole absorption range from 300 to 900 nm are designed, when blended with wide bandgap polymer poly[(2,6‐(4,8‐bis(5‐(2‐ethylhexyl)thiophen‐2‐yl)‐benzo[1,2‐b:4,5‐b′]dithiophene))‐alt‐(5,5‐(1′,3′‐di‐2‐thienyl‐5′,7′‐bis(2‐ethylhexyl)benzo[1′,2′‐c:4′,5′‐c′]dithiophene‐4,8‐dione))] (PBDB‐T) and narrow bandgap polymer PTB7‐Th, respectively, the PBDB‐T: F‐M system exhibits a high V_oc of 0.98 V and the PTB7‐Th: NOBDT system shows a remarkable J_sc of 19.16 mA cm^?2, which demonstrate their potential in the TOSCs. With the guidance of optical simulation, by systematically optimizing the thickness of each layer in the TOSC, an outstanding power conversion efficiency of 14.11%, with a V_oc of 1.71 V, a J_sc of 11.72 mA cm^?2, and a satisfactory fill factor of 0.70 is achieved; this result is one of the top efficiencies reported to date in the field of organic solar cells.     

Surpassing 10% Efficiency Benchmark for Nonfullerene Organic Solar Cells by Scalable Coating in Air from Single Nonhalogenated Solvent

The commercialization of nonfullerene organic solar cells (OSCs) critically relies on the response under typical operating conditions (for instance, temperature and humidity) and the ability of scale‐up. Despite the rapid increase in power conversion efficiency (PCE) of spin‐coated devices fabricated in a protective atmosphere, the efficiencies of printed nonfullerene OSC devices by blade coating are still lower than 6%. This slow progress significantly limits the practical printing of high‐performance nonfullerene OSCs. Here, a new and relatively stable nonfullerene combination is introduced by pairing the nonfluorinated acceptor IT‐M with the polymeric donor FTAZ. Over 12% efficiency can be achieved in spin‐coated FTAZ:IT‐M devices using a single halogen‐free solvent. More importantly, chlorine‐free, blade coating of FTAZ:IT‐M in air is able to yield a PCE of nearly 11% despite a humidity of ≈50%. X‐ray scattering results reveal that large π–π coherence length, high degree of face‐on orientation with respect to the substrate, and small domain spacing of ≈20 nm are closely correlated with such high device performance. The material system and approach yield the highest reported performance for nonfullerene OSC devices by a coating technique approximating scalable fabrication methods and hold great promise for the development of low‐cost, low‐toxicity, and high‐efficiency OSCs by high‐throughput production.     

Balanced Partnership between Donor and Acceptor Components in Nonfullerene Organic Solar Cells with >12% Efficiency

Relative to electron donors for bulk heterojunction organic solar cells (OSCs), electron acceptors that absorb strongly in the visible and even near‐infrared region are less well developed, which hinders the further development of OSCs. Fullerenes as traditional electron acceptors have relatively weak visible absorption and limited electronic tunability, which constrains the optical and electronic properties required of the donor. Here, high‐performance fullerene‐free OSCs based on a combination of a medium‐bandgap polymer donor (FTAZ) and a narrow‐bandgap nonfullerene acceptor (IDIC), which exhibit complementary absorption, matched energy levels, and blend with pure phases on the exciton diffusion length scale, are reported. The single‐junction OSCs based on the FTAZ:IDIC blend exhibit power conversion efficiencies up to 12.5% with a certified value of 12.14%. Transient absorption spectroscopy reveals that exciting either the donor or the acceptor component efficiently generates mobile charges, which do not suffer from recombination to triplet states. Balancing photocurrent generation between the donor and nonfullerene acceptor removes undesirable constraints on the donor imposed by fullerene derivatives, opening a new avenue toward even higher efficiency for OSCs.     

Enhancing Performance of Large‐Area Organic Solar Cells with Thick Film via Ternary Strategy

Large‐scale fabrication of organic solar cells requires an active layer with high thickness tolerability and the use of environment‐friendly solvents. Thick films with high‐performance can be achieved via a ternary strategy studied herein. The ternary system consists of one polymer donor, one small molecule donor, and one fullerene acceptor. The small molecule enhances the crystallinity and face‐on orientation of the active layer, leading to improved thickness tolerability compared with that of a polymer‐fullerene binary system. An active layer with 270 nm thickness exhibits an average power conversion efficiency (PCE) of 10.78%, while the PCE is less than 8% with such thick film for binary system. Furthermore, large‐area devices are successfully fabricated using polyethylene terephthalate (PET)/Silver gride or indium tin oxide (ITO)‐based transparent flexible substrates. The product shows a high PCE of 8.28% with an area of 1.25 cm² for a single cell and 5.18% for a 20 cm² module. This study demonstrates that ternary organic solar cells exhibit great potential for large‐scale fabrication and future applications.     

Over 12% Efficiency Nonfullerene All‐Small‐Molecule Organic Solar Cells with Sequentially Evolved Multilength Scale Morphologies

In this paper, two near‐infrared absorbing molecules are successfully incorporated into nonfullerene‐based small‐molecule organic solar cells (NFSM‐OSCs) to achieve a very high power conversion efficiency (PCE) of 12.08%. This is achieved by tuning the sequentially evolved crystalline morphology through combined solvent additive and solvent vapor annealing, which mainly work on ZnP‐TBO and 6TIC, respectively. It not only helps improve the crystallinity of the ZnP‐TBO and 6TIC blend, but also forms multilength scale morphology to enhance charge mobility and charge extraction. Moreover, it simultaneously reduces the nongeminate recombination by effective charge delocalization. The resultant device performance shows remarkably enhanced fill factor and J_sc. These result in a very respectable PCE, which is the highest among all NFSM‐OSCs and all small‐molecule binary solar cells reported so far.