Bipolar Charge Transport in PCPDTBT‐PCBM Bulk‐Heterojunctions for Photovoltaic Applications

An experimental study of the transport properties of a low‐bandgap conjugated polymer giving high photovoltaic quantum efficiencies in the near infrared spectral region (E_g‐opt ～ 1.35 eV) is presented. Using a organic thin film transistor geometry, we demonstrate a relatively high in‐plane hole mobility, up to 1.5 · × 10^?2 cm² V^?1 s^?1 and quantify the electron mobility at 3 × · 10^?5 cm² V^?1 s^?1 on a SiO₂ dielectric. In addition, singular contact behavior results in bipolar quasi‐Ohmic injection both from low and high workfunction metals like LiF/Al and Au. X‐ray investigations revealed a degree of interchain π‐stacking that is probably embedded in a disordered matrix. Disorder also manifests itself in a strong positive field dependence of the hole mobility from the electric field. In blends made with the electron acceptor methanofullerene [6,6]‐phenyl C₆₁ butyric acid methyl ester (PCBM), the transistor characteristics suggest a relatively unfavorable intermixing of the two components for the application to photovoltaic devices. We attribute this to a too fine dispersion of [C60]‐PCBM in the polymer matrix, that is also confirmed by the quenching of the photoluminescence signal measured in PCPDTBT [C60]‐PCBM films with various composition. We show that a higher degree of phase separation can be induced during the film formation by using 1,8‐octanedithiol (ODT), which leads to a more efficient electron percolation in the [C60]‐PCBM. In addition, the experimental results, in combination with those of solar cells seem to support the correlation between the blend morphology and charge recombination. We tentatively propose that the drift length, and similarly the electrical fill factor, can be limited by the recombination of holes with electrons trapped on isolated [C60]‐PCBM clusters. Ionized and isolated [C60]‐PCBM molecules can modify the local electric field in the solar cell by build‐up of a space‐charge. The results also suggest that further improvements of the fill factor may also be limited by a strong electrical‐field dependence of the hole transport.     

Ultrafast Hole‐Transfer Dynamics in Polymer/PCBM Bulk Heterojunctions

Ultrafast dynamics of the hole‐transfer process from methanofullerene to a polymer in a polymer/PCBM bulk heterojunction are directly resolved. Injection of holes into MDMO‐PPV is markedly delayed with respect to [60]PCBM excitation. The fastest component of the delayed response is attributed to the PCBM–polymer hole‐transfer process (30 ± 10 fs), while the slower component (～150 fs) is provisionally assigned to energy transfer and/or relaxation inside PCBM nanoclusters. The charge generation through the hole transfer is therefore as fast and efficient as through the electron‐transfer process. Exciton harvesting efficiency after PCBM excitation crucially depends on the concentration of the methanofullerene in the blend, which is related to changes in the blend morphology. Ultrafast charge generation is most efficient when the characteristic scale of phase separation in the blend does not exceed ～20 nm. At larger‐scale phase separation, the exciton harvesting dramatically declines. The obtained results on the time scales of the ultrafast charge generation after PCBM excitation and their dependence on blend composition and morphology are instrumental for the future design of fullerene‐derivative‐based photovoltaic devices.     

Near IR Sensitization of Organic Bulk Heterojunction Solar Cells: Towards Optimization of the Spectral Response of Organic Solar Cells

The spectroscopic response of a poly(3‐hexylthiophene)/[6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (P3HT/PCBM)‐based bulk heterojunction solar cell is extended into the near infrared region (NIR) of the spectrum by adding the low bandgap polymer poly[2,6‐(4,4‐bis‐(2‐ethylhexyl)‐4H‐cyclopenta[2,1‐b;3,4‐b´]‐dithiophene)‐alt‐4,7‐(2,1,3‐benzothiadiazole)] [PCPDTBT] to the blend. The dominant mechanism behind the enhanced photosensitivity of the ternary blend is found to be a two‐step process: first, an ultrafast and efficient photoinduced charge transfer generates positive charges on P3HT and PCPDTBT and a negative charge on PCBM. In a second step, the positive charge on PCPDTBT is transferred to P3HT. Thus, P3HT serves two purposes. On the one hand it is involved in the generation of charge carriers by the photoinduced electron transfer to PCBM, and, on the other hand, it forms the charge transport matrix for the positive carriers transferred from PCPDTBT. Other mechanisms, such as energy transfer or photoinduced charge transfer directly between the two polymers, are found to be absent or negligible.     

Formation Mechanism of Fullerene Cation in Bulk Heterojunction Polymer Solar Cells

The charge carrier dynamics in blend films of [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) and conjugated polymers with different ionization potentials are measured using transient absorption spectroscopy to study the formation mechanism of PCBM radical cation, which was previously discovered for blend films of poly[2‐methoxy‐5‐(3,7‐dimethyloctyloxy)‐1,4‐phenylenevinylene] (MDMO‐PPV) and PCBM. On a nanosecond time scale after photoexcitation, polymer hole polaron and PCBM radical anion are observed but no PCBM radical cation is found in the blends. Subsequently, the fraction of polymer hole polarons decreases and that of PCBM radical cations increases with time. Finally, the fraction of PCBM radical cations becomes constant on a microsecond time scale. The final fraction of PCBM radical cation is dependent on the ionization potential of polymers but independent of the excitation wavelength. These findings show that the formation of PCBM radical cation is due to hole injection from polymer to PCBM domains. Furthermore, the energetic conditions for such hole injection in polymer/PCBM blend films are discussed on the basis of Monte Carlo analysis for hole hopping in a disordered donor/acceptor heterojunction with varying energetic parameters.     

The Relation Between Open‐Circuit Voltage and the Onset of Photocurrent Generation by Charge‐Transfer Absorption in Polymer : Fullerene Bulk Heterojunction Solar Cells

Photocurrent generation by charge‐transfer (CT) absorption is detected in a range of conjugated polymer–[6,6]‐phenyl C₆₁ butyric acid methyl ester (PCBM) based solar cells. The low intensity CT absorption bands are observed using a highly sensitive measurement of the external quantum efficiency (EQE) spectrum by means of Fourier‐transform photocurrent spectroscopy (FTPS). The presence of these CT bands implies the formation of weak ground‐state charge‐transfer complexes in the studied polymer–fullerene blends. The effective band gap (E_g) of the material blends used in these photovoltaic devices is determined from the energetic onset of the photocurrent generated by CT absorption. It is shown that for all devices, under various preparation conditions, the open‐circuit voltage (V_oc) scales linearly with E_g. The redshift of the CT band upon thermal annealing of regioregular poly(3‐hexylthiophene):PCBM and thermal aging of poly(phenylenevinylene)(PPV):PCBM photovoltaic devices correlates with the observed drop in open‐circuit voltage of high‐temperature treated versus untreated devices. Increasing the weight fraction of PCBM also results in a redshift of E_g, proportional with the observed changes in V_oc for different PPV:PCBM ratios. As E_g corresponds with the effective bandgap of the material blends, a measurement of the EQE spectrum by FTPS allows us to measure this energy directly on photovoltaic devices, and makes it a valuable technique in the study of organic bulk heterojunction solar cells.     

Effect of Alkyl Side‐Chain Length on Photovoltaic Properties of Poly(3‐alkylthiophene)/PCBM Bulk Heterojunctions

The morphological, bipolar charge‐carrier transport, and photovoltaic characteristics of poly(3‐alkylthiophene) (P3AT):[6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM) blends are studied as a function of alkyl side‐chain length m, where m equals the number of alkyl carbon atoms. The P3ATs studied are poly(3‐butylthiophene) (P3BT, m = 4), poly(3‐pentylthiophene) (P3PT, m = 5), and poly(3‐hexylthiophene) (P3HT, m = 6). Solar cells with these blends deliver similar order of photo‐current yield (exceeding 10 mA cm^?2) irrespective of side‐chain length. Power conversion efficiencies of 3.2, 4.3, and 4.6% are within reach using solar cells with active layers of P3BT:PCBM (1:0.8), P3PT:PCBM (1:1), and P3HT:PCBM (1:1), respectively. A difference in fill factor values is found to be the main source of efficiency difference. Morphological studies reveal an increase in the degree of phase separation with increasing alkyl chain length. Moreover, while P3PT:PCBM and P3HT:PCBM films have similar hole mobility, measured by hole‐only diodes, the hole mobility in P3BT:PCBM lowers by nearly a factor of four. Bipolar measurements made by field‐effect transistor showed a decrease in the hole mobility and an increase in the electron mobility with increasing alkyl chain length. Balanced charge transport is only achieved in the P3HT:PCBM blend. This, together with better processing properties, explains the superior properties of P3HT as a solar cell material. P3PT is proved to be a potentially competitive material. The optoelectronic and charge transport properties observed in the different P3AT:PCBM bulk heterojunction (BHJ) blends provide useful information for understanding the physics of BHJ films and the working principles of the corresponding solar cells.     

Photoconductivity of a Low‐Bandgap Conjugated Polymer

The photoconductive properties of a novel low‐bandgap conjugated polymer, poly[2,6‐(4,4‐bis‐(2‐ethylhexyl)‐4H‐cyclopenta[2,1‐b;3,4‐b′]dithiophene)‐alt‐4,7‐(2,1,3‐benzothiadiazole)], PCPDTBT, with an optical energy gap of E_g ～ 1.5 eV, have been studied. The results of photoluminescence and photoconductivity measurements indicate efficient electron transfer from PCPDTBT to PCBM ([6,6]‐phenyl‐C61 butyric acid methyl ester, a fullerene derivative), where PCPDTBT acts as the electron donor and PCBM as the electron acceptor. Electron‐transfer facilitates charge separation and results in prolonged carrier lifetime, as observed by fast (t > 100 ps) transient photoconductivity measurements. The photoresponsivities of PCPDTBT and PCPDTBT:PCBM are comparable to those of poly(3‐hexylthiophene), P3HT, and P3HT:PCBM, respectively. Moreover, the spectral sensitivity of PCPDTBT:PCBM extends significantly deeper into the infrared, to 900 nm, than that of P3HT. The potential of PCPDTBT as a material for high‐efficiency polymer solar cells is discussed.     

Effects of Photo‐oxidation on the Performance of Poly[2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐1,4‐phenylene vinylene]:[6,6]‐Phenyl C61‐Butyric Acid Methyl Ester Solar Cells

A study of the photo‐oxidation of films of poly[2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐1,4‐phenylene vinylene] (MDMO‐PPV) blended with [6,6]‐phenyl C₆₁‐butyric acid methyl ester (PCBM), and solar cells based thereon, is presented. Solar‐cell performance is degraded primarily through loss in short‐circuit current density, J_SC. The effect of the same photodegradation treatment on the optical‐absorption, charge‐recombination, and charge‐transport properties of the active layer is studied. It is concluded that the loss in J_SC is primarily due to a reduction in charge‐carrier mobility, owing to the creation of more deep traps in the polymer during photo‐oxidation. Recombination is slowed down by the degradation and cannot therefore explain the loss in photocurrent. Optical absorption is reduced by photo‐bleaching, but the size of this effect alone is insufficient to explain the loss in device photocurrent.     

Charge‐Separation Dynamics in Inorganic–Organic Ternary Blends for Efficient Infrared Photodiodes

Knowledge about the working mechanism of the PbS:P3HT:PCBM [P3HT=poly(3‐hexylthiophene), PCBM=[6,6]‐phenyl‐C₆₁ ‐butyric acid methyl ester] hybrid blend used for efficient near‐infrared photodiodes is obtained from time‐resolved photoluminescence (PL) studies. To understand the role of each component in the heterojunction, the PL dynamics of the ternary (PbS:P3HT:PCBM) blend and the binary (PbS:P3HT, PbS:PCBM and P3HT:PCBM) blends are compared with the PL of the pristine PbS nanocrystals (NCs) and P3HT. In the ternary blend the efficiency of the charge transfer is significantly enhanced compared to the one of PbS:P3HT and PbS:PCBM blends, indicating that both hole and electron transfer from excited NCs to the polymer and fullerene occur. The hole transfer towards the P3HT determines the equilibration of their population in the NCs after the electron transfer towards PCBM, allowing their re‐excitation and new charge transfer process.     

Organic Field‐Effect Devices as Tool to Characterize the Bipolar Transport in Polymer‐Fullerene Blends: The Case of P3HT‐PCBM

In organic bulk heterojunction solar cells (oBHJ) the blend morphology in combination with the charge transport properties of the individual components controls the extracted photocurrent. The organic field‐effect transistor (OFET) has been proved as a powerful instrument to evaluate the unipolar carrier transport properties in a wide range of cases. In our work we extend the OFET concept to the evaluation of the bipolar transport properties in polymer‐fullerenes blends and propose a method to improve the accuracy of the evaluation. The method is based on capacitance–voltage (C–V) measurements on MOS structures prepared on the same blends and delivers complementary information on the bulk heterojunction to the one obtained with FETs. The relevance for photovoltaic applications is investigated through the correlation between the current–voltage behavior of solar cells and the bipolar mobility for composites with varying polymer molecular weight and processed from different solvents. In particular the transport features of solar cells produced from o‐Xylene (oX), a non chlorinated solvent more suitable to production requirements, have been compared to the one of devices cast from Chlorobenzene (CB) solution. For the P3HT‐PCBM blend a consistent correlation between the mobility and the electrical fill factor and power performance was found. A significant asymmetry in the bipolar carrier mobility, together with low electron mobility dependent on the M_w value, affects the performances of thick o‐Xylene cast devices. In the case of devices processed from Chlorobenzene the slower carrier has higher mobility and the small electrical losses detected are eventually more related to the formation of space‐charge and eventually to surface recombination. This results in an efficient charge collection that is almost thickness independent. We report a dependence of the slow‐carrier type (electrons or holes) and their mobility on the specific combination of molecular weight and solvent. The mobility data and the solar cell performance coherently fit to the prediction of a device model only based on the drift of carriers under the built‐in electric field originated in the donor‐acceptor oBHJ.     

Hole Transport in Poly(phenylene vinylene)/Methanofullerene Bulk‐Heterojunction Solar Cells

A fundamental limitation of the photocurrent of solar cells based on a blend of poly(2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐p‐phenylene vinylene) (MDMO‐PPV) and [6,6]‐phenyl C₆₁‐butyric acid methyl ester (PCBM) is caused by the mobility of the slowest charge‐carrier species, the holes in the MDMO‐PPV. In order to allow the experimentally observed photocurrents electrostatically, a hole mobility of at least 10^–8 m² V^–1 s^–1 is required, which exceeds the observed hole mobility in pristine MDMO‐PPV by more than two orders of magnitude. However, from space‐charge‐limited conduction, admittance spectroscopy, and transient electroluminescence measurements, we found a hole mobility of 2 × 10^–8 m² V^–1 s^–1 for the MDMO‐PPV phase in the blend at room temperature. Consequently, the charge‐carrier transport in a MDMO‐PPV:PCBM‐based solar cell is much more balanced than previously assumed, which is a necessary requirement for the reported high fill factors of above 50 %.     

Nanomorphology and Charge Generation in Bulk Heterojunctions Based on Low‐Bandgap Dithiophene Polymers with Different Bridging Atoms

Carbon bridged (C‐PCPDTBT) and silicon‐bridged (Si‐PCPDTBT) dithiophene donor–acceptor copolymers belong to a promising class of low bandgap materials. Their higher field‐effect mobility, as high as 10^?2 cm² V^?1 s^?1 in pristine films, and their more balanced charge transport in blends with fullerenes make silicon‐bridged materials better candidates for use in photovoltaic devices. Striking morphological changes are observed in polymer:fullerene bulk heterojunctions upon the substitution of the bridging atom. XRD investigation indicates increased π–π stacking in Si‐PCPDTBT compared to the carbon‐bridged analogue. The fluorescence of this polymer and that of its counterpart C‐PCPDTBT indicates that the higher photogeneration achieved in Si‐PCPDTBT:fullerene films (with either [C60]PCBM or [C70]PCBM) can be correlated to the inactivation of a charge‐transfer complex and to a favorable length of the donor–acceptor phase separation. TEM studies of Si‐PCPDTBT:fullerene blended films suggest the formation of an interpenetrating network whose phase distribution is comparable to the one achieved in C‐PCPDTBT:fullerene using 1,8‐octanedithiol as an additive. In order to achieve a balanced hole and electron transport, Si‐PCPDTBT requires a lower fullerene content (between 50 to 60 wt%) than C‐PCPDTBT (more than 70 wt%). The Si‐PCPDTBT:[C70]PCBM OBHJ solar cells deliver power conversion efficiencies of over 5%.     

Nanoscale Morphology of Conjugated Polymer/Fullerene‐Based Bulk‐ Heterojunction Solar Cells

The relation between the nanoscale morphology and associated device properties in conjugated polymer/fullerene bulk‐heterojunction “plastic solar cells” is investigated. We perform complementary measurements on solid‐state blends of poly[2‐methoxy‐5‐(3,7‐dimethyloctyloxy)]‐1,4‐phenylenevinylene (MDMO‐PPV) and the soluble fullerene C₆₀ derivative 1‐(3‐methoxycarbonyl) propyl‐1‐phenyl [6,6]C₆₁ (PCBM), spin‐cast from either toluene or chlorobenzene solutions. The characterization of the nanomorphology is carried out via scanning electron microscopy (SEM) and atomic force microscopy (AFM), while solar‐cell devices were characterized by means of current–voltage (I–V) and spectral photocurrent measurements. In addition, the morphology is manipulated via annealing, to increase the extent of phase separation in the thin‐film blends and to identify the distribution of materials. Photoluminescence measurements confirm the demixing of the materials under thermal treatment. Furthermore the photoluminescence of PCBM clusters with sizes of up to a few hundred nanometers indicates a photocurrent loss in films of the coarser phase‐separated blends cast from toluene. For toluene‐cast films the scale of phase separation depends strongly on the ratio of MDMO‐PPV to PCBM, as well as on the total concentration of the casting solution. Finally we observe small beads of 20–30 nm diameter, attributed to MDMO‐PPV, in blend films cast from both toluene and chlorobenzene.     

“Solvent Annealing” Effect in Polymer Solar Cells Based on Poly(3‐hexylthiophene) and Methanofullerenes

The self‐organization of the polymer in solar cells based on regioregular poly(3‐hexylthiophene) (RR‐P3HT):[6,6]‐phenyl C₆₁‐butyric acid methyl ester (PCBM) is studied systematically as a function of the spin‐coating time t_s (varied from 20–80 s), which controls the solvent annealing time t_a, the time taken by the solvent to dry after the spin‐coating process. These blend films are characterized by photoluminescence spectroscopy, UV‐vis absorption spectroscopy, atomic force microscopy, and grazing incidence X‐ray diffraction (GIXRD) measurements. The results indicate that the π‐conjugated structure of RR‐P3HT in the films is optimally developed when t_a is greater than 1 min (t_s ～ 50 s). For t _s < 50 s, both the short‐circuit current (J_SC) and the power conversion efficiency (PCE) of the corresponding polymer solar cells show a plateau region, whereas for 50 < t_s < 55 s, the J_SC and PCE values are significantly decreased, suggesting that there is a major change in the ordering of the polymer in this time window. The PCE decreases from 3.6 % for a film with a highly ordered π‐conjugated structure of RR‐P3HT to 1.2 % for a less‐ordered film. GIXRD results confirm the change in the ordering of the polymer. In particular, the incident photon‐to‐electron conversion efficiency spectrum of the less‐ordered solar cell shows a clear loss in both the overall magnitude and the long‐wavelength response. The solvent annealing effect is also studied for devices with different concentrations of PCBM (PCBM concentrations ranging from 25 to 67 wt %). Under “solvent annealing” conditions, the polymer is seen to be ordered even at 67 wt % PCBM loading. The open‐circuit voltage (V_OC) is also affected by the ordering of the polymer and the PCBM loading in the active layer.     

Formation of Methanofullerene Cation in Bulk Heterojunction Polymer Solar Cells Studied by Transient Absorption Spectroscopy

Photogenerated charge carriers for blend films of poly[2‐methoxy‐5‐(3,7‐dimethyloctyloxy)‐1,4‐phenylenevinylene] (MDMO‐PPV) and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) have been investigated by transient absorption spectroscopy. The blend film with a low PCBM fraction (<10 wt %) exhibits a wide absorption that ranges from 900 to 1000 nm, which is characteristic of the MDMO‐PPV hole polaron and PCBM radical anion. On the other hand, the blend film with a higher PCBM fraction (> 30 wt %) exhibits a major absorption band at ∼900 nm, which is characteristic of the PCBM radical cation. For identification of charge carriers, the absorption spectrum and molar absorption coefficient of each charged species have been evaluated separately using various combinations of electron donor and acceptor materials. Consequently, the MDMO‐PPV hole polaron has been found to have a broad absorption at ∼950 nm and the PCBM radical anion and cation show a distinct absorption at 1020 and 890 nm, respectively. On the basis of these absorption spectra, the transient spectra observed for the blend films have been simulated. The spectrum for a low PCBM fraction is well reproduced by superposition of the absorption spectra of the MDMO‐PPV hole polaron and PCBM radical anion. On the other hand, the spectrum for a high PCBM fraction is well reproduced by superposition of the absorption spectra of the MDMO‐PPV hole polaron, PCBM radical anion, and PCBM radical cation, which indicates that the PCBM radical cation is formed in the blend films with PCBM at a high concentration. Possible mechanisms for the formation of the PCBM radical cation in the blend are also discussed.     

All‐Polymer Bistable Resistive Memory Device Based on Nanoscale Phase‐Separated PCBM‐Ferroelectric Blends

All polymer nonvolatile bistable memory devices are fabricated from blends of ferroelectric poly(vinylidenefluoride–trifluoroethylene (P(VDF‐TrFE)) and n‐type semiconducting [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM). The nanoscale phase separated films consist of PCBM domains that extend from bottom to top electrode, surrounded by a ferroelectric P(VDF‐TrFE) matrix. Highly conducting poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) polymer electrodes are used to engineer band offsets at the interfaces. The devices display resistive switching behavior due to modulation of this injection barrier. With careful optimization of the solvent and processing conditions, it is possible to spin cast very smooth blend films (R_rms ≈ 7.94 nm) and with good reproducibility. The devices exhibit high I_on/I_off ratios (≈3 × 10³), low read voltages (≈5 V), excellent dielectric response at high frequencies (?_r ≈ 8.3 at 1 MHz), and excellent retention characteristics up to 10 000 s.     

The Effect of Thermal Treatment on the Morphology and Charge Carrier Dynamics in a Polythiophene–Fullerene Bulk Heterojunction

The influence of various thermal treatment steps on the morphology and the photoconductive properties of a non‐contacted, 50 nm thick blend (50:50 wt.‐%) of [6,6]‐phenyl C₆₁‐butyric acid methyl ester (PCBM) and poly(3‐hexyl thiophene) (P3HT) spin‐coated from chloroform has been studied using transmission electron microscopy (TEM) and the electrodeless time‐resolved microwave conductivity technique. After annealing the film for 5 min at 80 °C, TEM images show the formation of crystalline fibrils of P3HT due to a more ordered packing of the polymer chains. The thermal treatment results in a large increase of the photoconductivity, due to an enhancement of the hole mobility in these crystalline P3HT domains from 0.0056 cm² V^–1 s ^–1 for the non‐annealed sample to 0.044 cm² V^–1 s ^–1 for the sample annealed at 80 °C. In contrast, the temporal shape of the photoconductivity, with typical decay half‐times, τ_1/2, of 1 μs for the lowest excitation intensities, is unaffected by the temperature treatment. Further annealing of the sample at 130 °C results in the formation of three different substructures within the heterojunction: a PCBM:P3HT blend with PCBM‐rich clusters, a region depleted of PCBM, and large PCBM single crystals. Only a minor increase in the amplitude, but a tenfold rise of the decay time of the photoconductivity, is observed. This is explained by the formation of PCBM‐rich clusters and large PCBM single crystals, resulting in an increased diffusional escape probability for mobile charge carriers and hence reduced recombination.     

Effects of Annealing on the Nanomorphology and Performance of Poly(alkylthiophene):Fullerene Bulk‐Heterojunction Solar Cells

The evolution of nanomorphology within thin solid‐state films of poly(3‐alkylthiophene):[6,6]‐phenyl‐C₆₁ butyric acid methyl ester (P3AT:PCBM) blends during the film formation and subsequent thermal annealing is reported. In detail, the influence of the P3AT's alkyl side chain length on the polymer/fullerene phase separation is discussed. Butyl, hexyl, octyl, decyl, and dodecyl side groups are investigated. All of the P3ATs used were regioregular. To elucidate the nanomorphology, atomic force microscopy (AFM), X‐ray diffraction, and optical spectroscopy are applied. Furthermore, photovoltaic devices of each of the different P3ATs have been constructed, characterized, and correlated with the nanostructure of the blends. It is proposed that the thermal‐annealing step, commonly applied to these P3AT:PCBM blend films, controls two main issues at the same time: a) the crystallization of P3AT and b) the phase separation and diffusion of PCBM. The results show that PCBM diffusion is the main limiting process for reaching high device performances.     

Ambipolar Charge Transport in Films of Methanofullerene and Poly(phenylenevinylene)/Methanofullerene Blends

Herein, we report experimental studies of electron and hole transport in thin films of [6,6]‐phenyl C61 butyric acid methyl ester (PCBM) and in blends of poly[2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐1,4‐phenylenevinylene] (MDMO‐PPV) with PCBM. The low‐field hole mobility in pristine MDMO‐PPV is of the order of 10^–7 cm² V^–1 s^–1, in agreement with previous studies, whereas the electron mobility in pristine PCBM was found by current‐density–voltage (J–V) measurements to be of the order of 10^–2 cm² V^–1 s^–1, which is about one order of magnitude greater than previously reported. Adding PCBM to the blend increases both electron and hole mobilities, compared to the pristine polymer, and results in less dispersive hole transport. The hole mobility in a blend containing 67 wt.‐% PCBM is at least two orders of magnitude greater than in the pristine polymer. This result is independent of measurement technique and film thickness, indicating a true bulk property of the material. We therefore propose that PCBM may assist hole transport in the blend, either by participating in hole transport or by changing the polymer‐chain packing to enhance hole mobility. Time‐of‐flight mobility measurements of PCBM dispersed in a polystyrene matrix yield electron and hole mobilities of similar magnitude and relatively non‐dispersive transport. To the best of our knowledge, this is the first report of hole transport in a methanofullerene. We discuss the conditions under which hole transport in the fullerene phase of a polymer/fullerene blend may be expected. The relevance to photovoltaic device function is also discussed.