Cocatalyst‐Free Photocatalysts for Efficient Visible‐Light‐Induced H2 Production: Porous Assemblies of CdS Quantum Dots and Layered Titanate Nanosheets

Highly efficient, visible‐light‐induced H₂ generation can be achieved without the help of a Pt cocatalyst by new hybrid photocatalysts, in which CdS quantum dots (QDs) (particle size ≈2.5 nm) are incorporated in the porous assembly of sub‐nanometer‐thick layered titanate nanosheets. Due to the very‐limited crystal dimension of component semiconductors, the electronic structure of CdS QDs is strongly coupled with that of the layered titanate nanosheets, leading to an efficient electron transfer between them and the enhancement of the CdS photostability. As a consequence of the promoted electron transfer, the photoluminescence of CdS QDs is nearly quenched after hybridization, indicating the almost‐suppression of electron‐hole recombination. These Pt‐cocatalyst‐free, CdS‐layered titanate nanohybrids show much‐higher photocatalytic activity for H₂ production than the precursor CdS QDs and layered titanate, which is due to the increased lifetime of the electrons and holes, the decrease of the bandgap energy, and the expansion of the surface area upon hybridization. The observed photocatalytic efficiency of these Pt‐free hybrids (≈1.0 mmol g^?1 h^?1) is much greater than reported values of other Pt‐free CdS‐TiO₂ systems. This finding highlights the validity of 2D semiconductor nanosheets as effective building blocks for exploring efficient visible‐light‐active photocatalysts for H₂ production.     

Plasmonic Janus‐Composite Photocatalyst Comprising Au and C–TiO2 for Enhanced Aerobic Oxidation over a Broad Visible‐Light Range

Asymmetric Janus nanostructures containing a gold nanocage (NC) and a carbon–titania hybrid nanocrystal (AuNC/(C–TiO₂)) are prepared using a novel and facile microemulsion‐based approach that involves the assistance of ethanol. The localized surface plasmon resonance of the Au NC with a hollow interior and porous walls induce broadband visible‐light harvesting in the Janus AuNC/(C–TiO₂). An acetone evolution rate of 6.3 μmol h^?1 g^?1 is obtained when the Janus nanostructure is used for the photocatalytic aerobic oxidation of iso‐propanol under visible light (λ = 480–910 nm); the rate is 3.2 times the value of that obtained with C–TiO₂, and in photo‐electrochemical investigations an approximately fivefold enhancement is obtained. Moreover, when compared with the core–shell structure (AuNC@(C–TiO₂) and a gold–carbon–titania system where Au sphere nanoparticles act as light‐harvesting antenna, Janus AuNC/(C–TiO₂) exhibit superior plasmonic enhancement. Electromagnetic field simulation and electron paramagnetic resonance results suggest that the plasmon–photon coupling effect is dramatically amplified at the interface between the Au NC and C–TiO₂, leading to enhanced generation of energetic hot electrons for photocatalysis.     

Piezoelectric‐Effect‐Enhanced Full‐Spectrum Photoelectrocatalysis in p–n Heterojunction

Photoelectrochemical (PEC) water splitting offers a promising strategy for converting solar energy to chemical fuels. Herein, a piezoelectric‐effect–enhanced full‐spectrum photoelectrocatalysis with multilayered coaxial titanium dioxide/barium titanate/silver oxide (TiO₂/BTO/Ag₂O) nanorod array as the photoanode is reported. The vertically grown nanorods ensure good electron conductivity, which enables fast transport of the photogenerated electrons. Significantly, the insertion of a piezoelectric BaTiO₃ (BTO) nanolayer at the p‐type Ag₂O and n‐type TiO₂ interface created a polar charge‐stabilized electrical field. It maintains a sustainable driving force that attract the holes of TiO₂ and the electrons of Ag₂O, resulting in greatly increased separation and inhibited recombination of the photogenerated carriers. Furthermore, Ag₂O as a narrow bandgap semiconductor has a high ultraviolet–visible–near infrared (UV–vis–NIR) photoelectrocatalytic activity. The TiO₂/BTO/Ag₂O, after poling, successfully achieves a prominent photocurrent density, as high as 1.8 mA cm^?2 at 0.8 V versus Ag/Cl, which is about 2.6 times the TiO₂ nanorod photoanode. It is the first time that piezoelectric BaTiO₃ is used for tuning the interface of p‐type and n‐type photoelectrocatalyst. With the enhanced light harvesting, efficient photogenerated electron–hole pairs' separation, and rapid charge transfer at the photoanode, an excellent photoelectrocatalytic activity is realized.     

Enhanced Light‐Harvesting and Photocatalytic Properties in Morph‐TiO2 from Green‐Leaf Biotemplates

The unique structure of green leaves endows them with an extremely high light‐harvesting efficiency. In this work, green leaves are applied as biotemplates to synthesize morph‐TiO₂. The structural features favorable for light harvesting from the macro‐ to the nanoscale are replicated in morph‐TiO₂ through a two‐step infiltration process and the N contained in the original leaves is self‐doped into the resulting samples. The absorbance intensities within the visible‐light range of morph‐TiO₂ derived from different leaves increase by 103–258% and the band‐gap‐absorption onsets at the edge of the UV and visible‐light range show a red‐shift of 25–100 nm compared to those in TiO₂ without the template. The photocatalytic activity of morph‐TiO₂ is also improved, as proven by an electron paramagnetic resonance (EPR) study and degradation of rhodamine dye under irradiation with UV and visible light. The present work, as a new strategy, is of far‐reaching significance in learning from nature, driving us to make full use of the most‐abundant resources and structure‐introduced functions endowed by nature, opening up possibilities for extensive study of the physical and chemical properties of morph‐structured oxides and extending their potential for use in applications such as solar cells, photocatalysts, photoelectrical devices, and photoinduced sensors.     

Boosting Visible Light Harvesting in p‐Type Ternary Oxides for Solar‐to‐Hydrogen Conversion Using Inverse Opal Structure

P‐type semiconductors based on ternary oxides have attracted wide interest owing to their earth‐crust abundance and favorable optoelectronic properties. Among the p‐type ternary oxides, delafossite‐phase CuFeO₂ has received considerable attention because it has the potential to fully harness visible light (<800 nm) owing to its narrow bandgap (1.4–1.6 eV). Despite the favorable optoelectronic properties predicted by theoretical studies, CuFeO₂ photocathodes have low quantum efficiency under visible light near the bandgap edge, which is a major bottleneck for efficient solar‐to‐hydrogen conversion. Herein, a novel method is presented for boosting visible‐light harvesting in the CuFeO₂ photocathode by employing an inverse opal structure as a periodic macrostructure. The periodic macroporous structure allows exceptional near‐bandgap photon harvesting, particularly within the range of 600–700 nm, owing to the enhanced light absorption due to multiple scattering together with the short diffusion distance for minority carriers toward the electrolyte. After surface modification with a low‐cost double hydroxide electrocatalyst, our CuFeO₂‐based photocathode exhibits a record‐breaking photocurrent density of 5.2 mA cm^?2 at ?0.1 V with respect to the reversible hydrogen electrode for water reduction among p‐type ternary oxide‐based photocathodes.     

Efficient TiO2 Photocatalysts from Surface Hybridization of TiO2 Particles with Graphite‐like Carbon

Surface hybridization of TiO₂ with graphite‐like carbon layers of a few molecular layers thickness yields efficient photocatalysts. Photoelectrochemical measurements confirm an electronic interaction between TiO₂ and the graphite‐like carbon. A TiO₂ photocatalyst with a carbon shell of three molecular layers thickness (～1 nm) shows the highest photocatalytic activity which is about two times higher than that of Degussa P25 TiO₂ under UV light irradiation. The mechanism of the enhanced photocatalytic activity under UV irradiation is based on the high migration efficiency of photoinduced electrons at the graphite‐like carbon/TiO₂ interface, which is due to the electronic interaction between both materials. In addition, a high activity under visible light irradiation is observed after graphite‐like carbon hybridization. TiO₂'s response is extended into the visible range of the solar spectrum due to the electronic coupling of π states of the graphite‐like carbon and conduction band states of TiO₂.     

Quantum‐Dot‐Functionalized Poly(styrene‐co‐acrylic acid) Microbeads: Step‐Wise Self‐Assembly,Characterization, and Applications for Sub‐femtomolar Electrochemical Detection of DNA Hybridization

A novel nanoparticle label capable of amplifying the electrochemical signal of DNA hybridization is fabricated by functionalizing poly(styrene‐co‐acrylic acid) microbeads with CdTe quantum dots. CdTe‐tagged polybeads are prepared by a layer‐by‐layer self‐assembly of the CdTe quantum dots (diameter = 3.07 nm) and polyelectrolyte on the polybeads (diameter = 323 nm). The self‐assembly procedure is characterized using scanning and transmission electron microscopy, and X‐ray photoelectron, infrared and photoluminescence spectroscopy. The mean quantum‐dot coverage is (9.54 ± 1.2) × 10³ per polybead. The enormous coverage and the unique properties of the quantum dots make the polybeads an effective candidate as a functionalized amplification platform for labelling of DNA or protein. Herein, as an example, the CdTe‐tagged polybeads are attached to DNA probes specific to breast cancer by streptavidin–biotin binding to construct a DNA biosensor. The detection of the DNA hybridization process is achieved by the square‐wave voltammetry of Cd²⁺ after the dissolution of the CdTe tags with HNO₃. The efficient carrier‐bead amplification platform, coupled with the highly sensitive stripping voltammetric measurement, gives rise to a detection limit of 0.52 fmol L^?1 and a dynamic range spanning 5 orders of magnitude. This proposed nanoparticle label is promising, exhibits an efficient amplification performance, and opens new opportunities for ultrasensitive detection of other biorecognition events.     

Substantial Cyano‐Substituted Fully sp2‐Carbon‐Linked Framework: Metal‐Free Approach and Visible‐Light‐Driven Hydrogen Evolution

Polymeric semiconductors are emerging as a kind of competitive photocatalysts for hydrogen evolution due to their well‐tunable structures, versatile functionalization, and low‐cost processibility. In this work, a series of conjugated porous polymers with substantial cyano‐substituted fully sp²‐carbon frameworks are efficiently synthesized by using electron‐deficient tricyanomesitylene as a key building block to promote an organic base‐catalyzed Knoevenagel condensation with various aldehyde‐substituted arenes. The resulting porous polymers feature donor‐acceptor structures with π‐extended conjugation, rendering them with distinct semiconducting properties. They possess hierarchically porous structures, nanoscale morphologies, and intriguing wettability. These promising physical characters, finely tailorable by varying the arene units, are essentially relevant to the abundant cynao substituents over the whole frameworks. The as‐prepared porous polymers exhibit excellent visible‐light‐driven photocatalytic activity for water‐splitting hydrogen evolution with apparent quantum yield up to 2.0% at 420 nm or 1.9% at 470 nm, among the highest values yet reported for porous polymer‐based photocatalysts, also representing the first example of such kinds of catalysts formed through a metal‐free‐catalyzed carbon–carbon coupling reaction.     

Carbon‐Nanotube‐Cored Cobalt Porphyrin as a 1D Nanohybrid Strategy for High‐Performance Lithium‐Ion Battery Anodes

Redox‐active organic electrode materials have garnered considerable interest as an emerging alternative to currently widespread inorganic‐(or metal)‐based counterparts in lithium‐ion batteries (LIBs). Practical use of these materials, however, has posed a challenge due to their electrically insulating nature, limited specific capacity, and poor electrochemical durability. Here, a new class of multiwalled‐carbon‐nanotube‐(MWCNT)‐cored, meso‐tetrakis(4‐carboxyphenyl)porphyrinato cobalt (CoTCPP) is demonstrated as a 1D nanohybrid (denoted as CC‐nanohybrid) strategy to develop an advanced LIB anode. CoTCPP, which is one of the metalloporphyrins having multielectron redox activities, shows strong noncovalent interactions with MWCNTs due to its conjugated π‐bonds, resulting in successful formation of the CC‐nanohybrids. The structural uniqueness of the CC‐nanohybrid facilitates electron transport and electrolyte accessibility, thereby improving their redox kinetics. Inspired by the 1D structure of the CC‐nanohybrid, all‐fibrous nanomat anode sheets are fabricated through concurrent electrospraying/electrospinning processes. The resulting nanomat anode sheets, driven by their 3D bicontinuous ion/electron conduction pathways, provide fast lithiation/delithiation kinetics, eventually realizing the well‐distinguishable lithiation behavior of CoTCPP. Notably, the nanomat anode sheets exhibit exceptional electrochemical performance (≈226 mAh g_sheet ^?1 and >1500 cycles at 5 C) and mechanical flexibility that lie far beyond those achievable with conventional LIB anode technologies.     

An enhanced visible light active rutile titania–copper/polythiophene nanohybrid material for the degradation of rhodamine B dye

A novel copper doped TiO₂ (TiO₂–Cu)/polythiophene (PTh) nanohybrid material with discrete polymer concentrations is devised by a modified sol–gel technique at low temperature. The XRD outcome revealed that the polythiophene and copper contents do not affect the crystal structure of TiO₂. SEM and TEM images of the TiO₂–Cu and nanohybrid denoted the presence of a nanoparticle sized core–shell structure. UV–visible absorption spectra of nanohybrid catalyst with diverse polymer concentrations broadcasted a broad and strong absorption in the visible region. A strong interaction between the interface of PTh and TiO₂–Cu was confirmed by FT-IR. The presence of Cu²⁺ ion and positively charged sulfur (polarons) throughout the polymer carbon content was manifested by XPS spectra. The photocatalytic activity of nanohybrid catalyst has been evaluated by degradation of Rhodamine B (RhB) under visible light irradiation. The effect of solution pH, catalyst dosage and initial concentration of RhB on the photocatalytic activity of TiO₂–Cu/PTh nanohybrid with different loadings is studied. It has been observed that the rate of degradation of RhB over TiO₂–Cu/PTh nanohybrid is better than TiO₂–Cu metal oxide under visible light irradiation.     

In Situ Formation of Copper‐Based Hosts Embedded within 3D N‐Doped Hierarchically Porous Carbon Networks for Ultralong Cycle Lithium–Sulfur Batteries

Lithium–sulfur (Li–S) batteries are promising energy storage systems due to their large theoretical energy density of 2600 Wh kg^?1 and cost effectiveness. However, the severe shuttle effect of soluble lithium polysulfide intermediates (LiPSs) and sluggish redox kinetics during the cycling process cause low sulfur utilization, rapid capacity fading, and a low coulombic efficiency. Here, a 3D copper, nitrogen co‐doped hierarchically porous graphitic carbon network developed through a freeze‐drying method (denoted as 3D Cu@NC‐F) is prepared, and it possesses strong chemical absorption and electrocatalytic conversion activity for LiPSs as highly efficient sulfur host materials in Li–S batteries. The porous carbon network consisting of 2D cross‐linked ultrathin carbon nanosheets provides void space to accommodate volumetric expansion upon lithiation, while the Cu, N‐doping effect plays a critical role for the confinement of polysulfides through chemical bonding. In addition, after sulfuration of Cu@NC‐F network, the in situ grown copper sulfide (Cu_xS) embedded within Cu_xS@NC/S‐F composite catalyzes LiPSs conversion during reversible cycling, resulting in low polarization and fast redox reaction kinetics. At a current density of 0.1 C, the Cu_xS@NC/S‐F composites' electrode exhibits an initial capacity of 1432 mAh g^?1 and maintains 1169 mAh g^?1 after 120 cycles, with a coulombic efficiency of nearly 100%.     

A DCM‐Type Red‐Fluorescent Dopant for High‐Performance Organic Electroluminescent Devices

2‐(2‐tert‐Butyl‐6‐((E)‐2‐(2,6,6‐trimethyl‐2,4,5,6‐tetrahydro‐1H‐pyrrolo[3,2,1‐ij]quinolin‐8‐yl)vinyl)‐4H‐pyran‐4‐ylidene)malononitrile (DCQTB) is designed and synthesized in high yield for application as the red‐light‐emitting dopant in organic light‐emitting diodes (OLEDs). Compared with 4‐(dicyanomethylene)‐2‐tert‐butyl‐6‐(1,1,7,7,‐tetramethyljulolidyl‐9‐enyl)‐4H‐pyran (DCJTB), one of the most efficient red‐emitting dopants, DCQTB exhibits red‐shifted fluorescence but blue‐shifted absorption. The unique characteristics of DCQTB with respect to DCJTB are utilized to achieve a red OLED with improved color purity and luminous efficiency. As a result, the device that uses DCQTB as dopant, with the configuration: indium tin oxide (ITO)/N,N′‐bis(1‐naphthyl)‐N,N′‐diphenyl‐1,1′‐biphenyl‐4,4′‐diamine (NPB; 60 nm)/tris(8‐quinolinolato) aluminum (Alq₃):dopant (2.3 wt %) (7 nm)/2,9‐dimethyl‐4,7‐diphenyl‐1,10‐phenanthroline (BCP; 12 nm)/Alq₃(45 nm)/LiF(0.3 nm):Al (300 nm), shows a larger maximum luminance (L_max = 6021 cd m^–2 at 17 V), higher maximum efficiency (η_max = 4.41 cd A^–1 at 11.5 V (235.5 cd m^–2)), and better chromaticity coordinates (Commission Internationale de l'Eclairage, CIE, (x,y) = (0.65,0.35)) than a DCJTB‐based device with the same structure (L_max = 3453 cd m^–2 at 15.5 V, η_max = 3.01 cd A^–1 at 10 V (17.69 cd m^–2), and CIE (x,y) = (0.62,0.38)). The possible reasons for the red‐shifted emission but blue‐shifted absorption of DCQTB relative to DCJTB are also discussed.     

A Visible‐ and NIR‐Light Responsive Photothermal Therapy Agent by Chirality‐Dependent MoO3−x Nanoparticles

Chirality‐based semiconducting nanocrystals, as an emerging area, are envisioned to have great potential in chiral sensing, biomedicine, and chiroptical devices. Herein, chiral substoichiometric molybdenum oxide (l /d ‐Cys‐MoO_3?x) nanoparticles are synthesized via step‐by‐step reduction treatment with chiral cysteine molecules. The obtained nanoparticles are used as visible‐ and near‐infrared‐light dual responsive photothermal therapy agent for tumor cell ablation. Notably, the chiral nanoparticles show chiral selectivity for incident light, i.e., when irradiated by left‐circularly polarized light, l ‐Cys‐MoO_3?x is the most sensitive agent giving the highest mortality for HeLa cell ablation in vitro, and vice versa for right‐circularly polarized light with d ‐Cys‐MoO_3?x. In comparison to traditional photothermal therapy with near‐field light source, the investigations with chiral visible light at 532 nm indicate the possibility of chiral Cys‐MoO_3?x nanoparticles for visible light‐based phototherapy via metal–ligand charge transfer chirality, which provides insights for new methods in nanotechnology supported photothermal treatments.     

Glucose‐Responsive Bioinorganic Nanohybrid Membrane for Self‐Regulated Insulin Release

A bioinorganic nanohybrid glucose‐responsive membrane is developed for self‐regulated insulin delivery analogous to a healthy human pancreas. The application of MnO₂ nanoparticles as a multifunctional component in a glucose‐responsive, protein‐based membrane with embedded pH‐responsive hydrogel nanoparticles is proposed. The bio‐nanohybrid membrane is prepared by crosslinking bovine serum albumin (BSA)–MnO₂ nanoparticle conjugates with glucose oxidase and catalase in the presence of poly(N‐isopropyl acrylamide‐co‐methacrylic acid) nanoparticles. The preparation and performance of this new nanocomposite material for a glucose‐responsive insulin release system is presented. The activity and stability of immobilized glucose oxidase and the morphology and mechanical properties of the membrane are investigated. The enzymatic activity is well preserved in the membranes. The use of MnO₂ nanoparticles not only reinforces the mechanical strength and the porous structure of the BSA‐based membrane, but enhances the long‐term stability of the enzymes. The in vitro release of insulin across the membrane is modulated by changes in glucose concentration mimicking possible fluctuations of blood‐glucose level in diabetic patients. A four‐fold increase in insulin permeation is observed when the glucose concentration is increased from normal to hyperglycemic levels, which returns to the baseline level when the glucose concentration is reduced to a normal level.     

Simultaneous Electrochemical Dual‐Electrode Exfoliation of Graphite toward Scalable Production of High‐Quality Graphene

Developing scalable methods to produce large quantities of high‐quality and solution‐processable graphene is essential to bridge the gap between laboratory study and commercial applications. Here an efficient electrochemical dual‐electrode exfoliation approach is developed, which combines simultaneous anodic and cathodic exfoliation of graphite. Newly designed sandwich‐structured graphite electrodes which are wrapped in a confined space with porous metal mesh serve as both electrodes, enabling a sufficient ionic intercalation. Mechanism studies reveal that the combination of electrochemical intercalation with subsequent thermal decomposition results in drastic expansion of graphite toward high‐efficiency production of graphene with high quality. By precisely controlling the intercalation chemistry, the two‐step approach leads to graphene with outstanding yields (85% and 48% for cathode and anode, respectively) comprising few‐layer graphene (1–3 layers, >70%), ultralow defects (I_D/I_G < 0.08), and high production rate (exceeding 25 g h^?1). Moreover, its excellent electrical conductivity (>3 × 10⁴ S m^?1) and great solution dispersibility in N‐methyl pyrrolidone (10 mg mL^?1) enable the fabrication of highly conductive (11 Ω sq^?1) and flexible graphene films by inkjet printing. This simple and efficient exfoliation approach will facilitate the development of large‐scale production of high‐quality graphene and holds great promise for its wide application.     

Transition‐Metal‐Carbide (Mo2C) Multiperiod Gratings for Realization of High‐Sensitivity and Broad‐Spectrum Photodetection

A novel hybrid phototransistor consisting of molybdenum carbide (Mo₂C) and molybdenum disulfide (MoS₂) is proposed. By exploiting the interface properties of MoS₂ and Mo₂C, a highly sensitive and broad‐spectral response photodetector is fabricated. The underlying mechanism of the enhanced performance is the efficient hot carrier injection from Mo₂C to MoS₂. The strong coupling of MoS₂ and Mo₂C at the interface provides the significantly low Schottky barrier height (≈70 meV), which gives rise to the significantly efficient hot carrier transfer from Mo₂C to MoS₂. The grating of metallic Mo₂C produces plasmonic resonance, which provides hot carriers to the MoS₂ channel. By adjusting the grating period of Mo₂C (400–1000 nm), the optimal photoresponse of light can be controlled, from visible to NIR. By integrating various Mo₂C multigrating periods (400–1000 nm) with MoS₂, a novel photodetector is demonstrated with high responsivity (R > 10³ A W^?1) and light‐to‐dark current ratio (>10²) over a broad spectral range (405–1310 nm). The proposed novel hybrid photodetector, 2D semiconductors with multigrating 2D metallic stripes, exhibits high sensitivity and broad spectral detection of light and can overcome the inherent weakness of conventional 2D photodetectors, paving the way forward for next‐generation photoelectric devices.     

3D‐Printed MOF‐Derived Hierarchically Porous Frameworks for Practical High‐Energy Density Li–O2 Batteries

Aprotic Li–O₂ batteries are promising candidates for next‐generation energy storage technologies owing to their high theoretical energy densities. However, their practically achievable specific energy is largely limited by the need for porous conducting matrices as cathode support and the passivation of cathode surface by the insulating Li₂O₂ product. Herein, a self‐standing and hierarchically porous carbon framework is reported with Co nanoparticles embedded within developed by 3D‐printing of cobalt‐based metal–organic framework (Co‐MOF) using an extrusion‐based printer, followed by appropriate annealing. The novel self‐standing framework possesses good conductivity and necessary mechanical stability, so that it can act as a porous conducting matrix. Moreover, the porous framework consists of abundant micrometer‐sized pores formed between Co‐MOF‐derived carbon flakes and meso‐ and micropores formed within the flakes, which together significantly benefit the efficient deposition of Li₂O₂ particles and facilitate their decomposition due to the confinement of insulating Li₂O₂ within the pores and the presence of Co electrocatalysts. Therefore, the self‐standing porous architecture significantly enhances the cell's practical specific energy, achieving a high value of 798 Wh kg^?1_cell. This study provides an effective approach to increase the practical specific energy for Li–O₂ batteries by constructing 3D‐printed framework cathodes.     

High‐Performance Wearable Micro‐Supercapacitors Based on Microfluidic‐Directed Nitrogen‐Doped Graphene Fiber Electrodes

Fiber‐shaped micro‐supercapacitors (micro‐SCs) have attracted enormous interest in wearable electronics due to high flexibility and weavability. However, they usually present a low energy density because of inhomogeneity and less pores. Here, we demonstrate a microfluidic‐directed strategy to synthesize homogeneous nitrogen‐doped porous graphene fibers. The porous fibers‐based micro‐SCs utilize solid‐state phosphoric acid/polyvinyl alcohol (H₃PO₄/PVA) and 1‐ethyl‐3‐methylimidazolium tetrafluoroborate/poly(vinylidenefluoride‐co‐hexafluoropropylene) (EMIBF₄/PVDF‐HFP) electrolytes, which show significant improvements in electrochemical performances. Ultralarge capacitance (1132 mF cm^?2), high cycling‐stability, and long‐term bending‐durability are achieved based on H₃PO₄/PVA. Additionally, high energy densities of 95.7–46.9 µWh cm^?2 at power densities of 1.5–15 W cm^?2 are obtained in EMIBF₄/PVDF‐HFP. The key to higher performances stems from microfluidic‐controlled fibers with a uniformly porous network, large specific surface area (388.6 m² g^?1), optimal pyridinic nitrogen (2.44%), and high electric conductivity (30785 S m^?1) for faster ion diffusion and flooding accommodation. By taking advantage of these remarkable merits, this study integrates micro‐SCs into flexible and fabric substrates to power audio–visual electronics. The main aim is to clarify the important role of microfluidic techniques toward the architecture of electrodes and promote development of wearable electronics.     

High‐Purity‐Blue and High‐Efficiency Electroluminescent Devices Based on Anthracene

Novel blue‐light‐emitting materials, 9,10‐bis(1,2‐diphenyl styryl)anthracene (BDSA) and 9,10‐bis(4′‐triphenylsilylphenyl)anthracene (BTSA), which are composed of an anthracene molecule as the main unit and a rigid and bulky 1,2‐diphenylstyryl or triphenylsilylphenyl side unit, have been designed and synthesized. Theoretical calculations on the three‐dimensional structures of BDSA and BTSA show that they have a non‐coplanar structure and inhibited intermolecular interactions, resulting in a high luminescence efficiency and good color purity. By incorporating these new, non‐doped, blue‐light‐emitting materials into a multilayer device structure, it is possible to achieve luminance efficiencies of 1.43 lm W^–1 (3.0 cd A^–1 at 6.6 V) for BDSA and 0.61 lm W^–1 (1.3 cd A^–1 at 6.7 V) for BTSA at 10 mA cm^–2. The electroluminescence spectrum of the indium tin oxide (ITO)/copper phthalocyanine (CuPc)/1,4‐bis[(1‐naphthylphenyl)‐amino]biphenyl (α‐NPD)/BDSA/tris(9‐hydroxyquinolinato)aluminum (Alq₃)/LiF/Al device shows a narrow emission band with a full width at half maximum (FWHM) of 55 nm and a λ_max = 453 nm. The FWHM of the ITO/CuPc/α‐NPD/BTSA/Alq₃/LiF/Al device is 53 nm, with a λ_max = 436 nm. Regarding color, the devices showed highly pure blue emission ((x,y) = (0.15,0.09) for BTSA, (x,y) = (0.14,0.10) for BDSA) at 10 mA cm^–2 in Commission Internationale de l'Eclairage (CIE) chromaticity coordinates.     

Single‐Crystalline p‐Type Zn3As2 Nanowires for Field‐Effect Transistors and Visible‐Light Photodetectors on Rigid and Flexible Substrates

Zn₃As₂ is an important p‐type semiconductor with the merit of high effective mobility. The synthesis of single‐crystalline Zn₃As₂ nanowires (NWs) via a simple chemical vapor deposition method is reported. High‐performance single Zn₃As₂ NW field‐effect transistors (FETs) on rigid SiO₂/Si substrates and visible‐light photodetectors on rigid and flexible substrates are fabricated and studied. As‐fabricated single‐NW FETs exhibit typical p‐type transistor characteristics with the features of high mobility (305.5 cm² V^?1 s^?1) and a high I_on/I_off ratio (10⁵). Single‐NW photodetectors on SiO₂/Si substrate show good sensitivity to visible light. Using the contact printing process, large‐scale ordered Zn₃As₂ NW arrays are successfully assembled on SiO₂/Si substrate to prepare NW thin‐film transistors and photodetectors. The NW‐array photodetectors on rigid SiO₂/Si substrate and flexible PET substrate exhibit enhanced optoelectronic performance compared with the single‐NW devices. The results reveal that the p‐type Zn₃As₂ NWs have important applications in future electronic and optoelectronic devices.