A structural–thermodynamic study of triphenylsilylcellulose

The purpose of this article is to report the characterization of a solution of triphenylsilylcellulose (TPSC) in terms of its rheologic properties by osmometry and viscometry to better understand processing parameters and conditions. This work is an extension of previous similar work on trimethylsilylcellulose (TMSC). TPSC was prepared in a medium of dimethylformamide (DMF) plus pyridine, under heterogeneous starting conditions and nitrogen atmosphere, by silylation of activated celluloses with triphenylchlorosilane at 115–120 °C. The isolated and purified ethers were characterized according to their polydispersities and their substitution degrees, by osmometry and viscometry in various solvents. The Mark–Houwink–Sakurada equation coefficients were evaluated in 1,1,1‐trichloroethane, chloroform, and o‐xylene at 30 °C and in o‐xylene over the 30–70 °C temperature range. The values of 2.12–2.18 obtained for exponent “a” correlated with the very low values of pre‐exponential factor (of 10^?12 order), indicating a high stiffness of the macromolecular chains. The viscous flow parameters for dilute solutions of TPSC in o‐xylene were determined in the temperature range 30–70 °C. The temperature dependence of the dynamic viscosity of the solutions obeys an Arrhenius‐type equation in which the apparent activation energy is linearly dependent on both the concentration and molecular weight of the solution. No significant dependence on concentration and molecular weight was found for the pre‐exponential factor. This behavior was attributed to the great stiffness of the macromolecular chains. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2875–2884, 2002     

Viscosity‐molecular weight relationship for cellulose solutions in either NMMO monohydrate or cuen

The intrinsic viscosities, [η], of nine cellulose samples, with molar masses from 50 × 10³ to 1 390 × 10³ were determined in the solvents NMMO*H₂O (N‐methyl morpholin N‐oxide hydrate) at 80°C and in cuen (copper II‐ethlenediamine) at 25°C. The evaluation of these results with respect to the Kuhn–Mark–Houwink relations shows that the data for NMMO*H₂O fall on the usual straight line in the double logarithmic plots only for M ≤ 158 10³; the corresponding [η]/M relation reads log ([η]/mL g⁻¹) = –1.465 + 0.735 log M. Beyond that molar mass [η] remains almost constant up to M ≈ 10⁶ and increases again thereafter. In contrast to NMMO*H₂O the cellulose solutions in cuen behave normal and the Kuhn–Mark–Houwink relation reads log ([η]/mL g⁻¹) = −1.185 + 0.735 log M. Possible reasons for the dissimilarities of the behavior of cellulose in these two solvents are being discussed. The comparison of three different methods for the determination of [η] from viscosity measurements at different polymer concentrations, c, demonstrates the advantages of plotting the natural logarithm of the relative viscosities as a function of c. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of quaternary ammonium ionomers

The cationic monomers, MPDMAC₁₆ and MPDMAC₁₈, were obtained by quaternization of methacrylamidopropyl–N,N′‐dimethylamine with n‐alkyl iodides (1‐iodohexadecane and 1‐iodooctadecane) in ethyl acetate. Hydrophobic ionomers of MPDMAC₁₆ and MPDMAC₁₈ with N‐substituted acrylamides were prepared at 60 ± 0.1°C in DMF using AIBN initiator. The cationic monomers and ionomers were characterized by ¹H‐ and ¹³C‐NMR spectroscopy. The copolymer composition was evaluated from elemental analysis data using carbon/nitrogen (C/N) ratio. The molecular weight distributions of ionomers were obtained from GPC analysis. Both the dilute solution and concentrated solution properties of ionomers were studied by viscometry at 30°C. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1100–1105, 2005     

Synthesis and characterization of new soluble poly(ester‐imide)s containing noncoplanar 2,2′‐dimethyl‐4,4′‐biphenylene unit

A new diimide–diacid chloride (3) containing a noncoplanar 2,2′‐dimethyl‐4,4′‐biphenylene unit was synthesized by treating 2,2′‐dimethyl‐4,4′‐diamino‐biphenylene with trimellitic anhydride followed by refluxing with thionyl chloride. Various new poly(ester‐imide)s were prepared from 3 with different bisphenols by solution polycondensation in nitrobenzene using pyridine as hydrogen chloride quencher at 170°C. Inherent viscosities of the poly(ester‐imide)s were found to range between 0.31 and 0.35 dL g^?1. All of the poly(ester‐imide)s, except the one containing pendent adamantyl group 5e, exhibited excellent solubility in the following solvents: N,N‐dimethylformamide, tetrahydrofuran, tetrachloroethane, dimethyl sulfoxide, N,N‐dimethylacetamide, N‐methyl‐2‐pyrrolidinone, m‐cresol, o‐chlorophenol, and chloroform. The polymers showed glass‐transition temperatures between 166 and 226°C. The 10% weight loss temperatures of the poly(ester‐imide)s, measured by TGA, were found to be in the range between 415 and 456°C in nitrogen. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2486–2493, 2004     

Synthesis and characterization of novel polyaspartimides derived from 2,2′‐dimethyl‐4,4′‐bis(4‐maleimidophenoxy)biphenyl and various diamines

A novel bismaleimide, 2,2′‐dimethyl‐4,4′‐bis(4‐maleimidophenoxy)biphenyl, containing noncoplanar 2,2′‐dimethylbiphenylene and flexible ether units in the polymer backbone was synthesized from 2,2′‐dimethyl‐4,4′‐bis(4‐aminophenoxy)biphenyl with maleic anhydride. The bismaleimide was reacted with 11 diamines using m‐cresol as a solvent and glacial acetic acid as a catalyst to produce novel polyaspartimides. Polymers were identified by elemental analysis and infrared spectroscopy, and characterized by solubility test, X‐ray diffraction, and thermal analysis (differential scanning calorimetry and thermogravimetric analysis). The inherent viscosities of the polymers varied from 0.22 to 0.48 dL g⁻¹ in concentration of 1.0 g dL⁻¹ of N,N‐dimethylformamide. All polymers are soluble in N‐methyl‐2‐pyrrolidone, N,N‐dimethylacetamide, N,N‐dimethylformamide, dimethylsulfoxide, pyridine, m‐cresol, and tetrahydrofuran. The polymers, except PASI‐4, had moderate glass transition temperature in the range of 188°–226°C and good thermo‐oxidative stability, losing 10% mass in the range of 375°–426°C in air and 357°–415°C in nitrogen. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 279–286, 1999     

Graft copolymerization of acrylic acid onto cellulose: Effects of pretreatments and crosslinking agent

The graft copolymerization of acrylic acid (AA) and 2‐acrylamido 2‐methylpropane sulfonic acid (AASO₃H) onto cellulose, in the presence or absence of crosslinking agent N,N′‐methylene bisacrylamide (NMBA), by using different concentrations of ceric ammonium nitrate (CAN) initiator in aqueous nitric acid solution at either 5 or 30°C was investigated. To investigate the effect of pretreatment of cellulose on the copolymerization, before some grafting reactions cellulose was pretreated with either 2 or 20 wt % NaOH solutions or heated in distilled water/aqueous nitric acid (2.5 × 10^?3 M) at 55°C. To determine how the excess of initiator affects the grafting and homopolymerization, separate reactions were carried out by removing the excess of ceric ions by filtration of the mixture of initiator solution and cellulose before the monomer addition. Extraction‐purified products were characterized by grafting percentage and equilibrium swelling capacity. Pretreatment of cellulose with NaOH solutions decreased the grafting percentage of copolymers. In the case of AA–AASO₃H mixtures, nonpretreated cellulose gave a higher grafting percentage than NaOH‐pretreated cellulose. Filtration also lowered the grafting of AA on the cellulose in the cases of pretreatment with either water or nitric acid. Copolymers with the highest grafting percentage (64.8%) and equilibrium swelling value (105 g H₂O/g copolymer) were obtained in grafting reactions carried out in the presence of NMBA at 5°C. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2267–2272, 2001     

Synthesis and characterization of novel optically active poly(amide–imide)s containing N,N′‐(pyromellitoyl)‐bis‐L‐valine diacid chloride and 5,5‐disubstituted hydantoin derivatives under microwave irradiation

Pyromellitic dianhydride (1,2,4,5‐benzenetetracarboxylic acid 1,2,4,5‐dianhydide) was reacted with L ‐valine in a mixture of acetic acid and pyridine (3:2) at room temperature, and then was refluxed at 90–100 °C, N,N′‐(pyromellitoyl)‐bis‐L ‐valine diacid was obtained in quantitative yield. The imide–acid was converted to N,N′‐(pyromellitoyl)‐bis‐L ‐valine diacid chloride by reaction with thionyl chloride. Rapid and highly efficient synthesis of a number of poly(amide–imide)s was achieved under microwave irradiation using a domestic microwave oven by polycondensation of N,N′‐(pyromellitoyl)‐bis‐L ‐valine diacid chloride with six different derivatives of 5,5‐disubstituted hydantoin compounds in the presence of a small amount of a polar organic medium that acts as a primary microwave absorber. A suitable organic medium was o‐cresol. The polycondensation proceeded rapidly, compared with conventional melt polycondensation and solution polycondensation and was almost completed within 8 min, giving a series of poly(amide–imide)s with inherent viscosities in the range 0.15–0.36 dl g^?1. The resulting poly(amide–imide)s were obtained in high yield and are optically active and thermally stable. All of the above compounds were fully characterized by Fourier‐transform infrared (FT‐IR) spectroscopy, elemental analysis, inherent viscosity (η_inh) measurements, solubility testing and specific rotation measurements. The thermal properties of the poly(amide–imide)s were investigated by using thermogravimetric analysis. Copyright © 2004 Society of Chemical Industry     

Grafting of N,N′‐methylenebisacrylamide onto cellulose using Co(III)‐acetylacetonate complex in aqueous medium

The grafting of N,N′‐methylenebisacrylamide (N,N′‐MBA) onto cellulose is carried out using the cobaltacetylacetonate complex (Co(acac)₃) under nitrogen atmosphere at 40°C. The rate of graft copolymerization has been studied as a function of [N,N′‐MBA], [Co(acac)₃], and temperature. The activation energy of grafting is found to be 156.0 k J mol⁻¹ within the temperature range of 30–60°C. The effect of perchloric acid, methanol, and surfactants on graft yield has also been studied and results are suitably explained. The higher efficiency of the metal chelate in initiation of graft copolymerization has been assumed due to the coordination of the π electrons of the N,N′‐MBA with the metal chelate, which facilitated the formation of the radicals through homolytic cleavage of metal–oxygen bond of the cobalt acetylacetonate complex. On the basis of the results, a suitable kinetic scheme for graft copolymerization is presented and rate expression is derived. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 906–912, 2000     

Preparation of cellulose derivatives containing carbazole chromophore

Cellulose derivatives containing long hydrocarbon side chains and the carbazole chromophore are prepared. N‐4′‐Bromobutylcarbazole is first synthesized from carbazole and 1,4‐dibromobutane. Alkylated carbazole is then reacted with cellulose acetate in dimethyl sulfoxide solution to produce cellulose ethers containing the desired chromophore. Polymers containing a mixture of alkyl side chains are also prepared by the subsequent addition of 1‐bromododecane to the reaction mixture. Characterization of the resulting cellulose derivatives by FTIR spectroscopy indicates that the deacetylation of cellulose acetate and the subsequent etherification are both complete. In addition, the incorporation of the carbazole chromophore is clearly shown by ¹H‐ and ¹³C‐NMR spectroscopy. Polymers of different carbazole content, ranging from 2.9 to 1.1 chromophores per anhydroglucose repeat unit, are obtained by varying the reaction conditions. Substitution is found to be controlled primarily by the quantity of alkylating agent introduced while variation of the reaction time has little effect. This method is used to prepare (dodecyl)_y(N‐4′‐carbazolylbutyl)_xcellulose, (decyl)_y(N‐4′‐carbazolylbutyl)_xcellulose, and (butyl)_y(N‐4′‐carbazolylbutyl)_xcellulose. Cellulose acetate can be replaced by (methyl)cellulose as the starting material to obtain analogous products. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2764–2772, 1999     

Isolation and Characterization of Potent Strains for Metabolizing Paint VOCs from an Active Trickle‐bed Air Biofilter

In this study, seven strains of cells were isolated from a trickle‐bed air biofilter used for continuously treating paint of volatile organic compounds (VOCs) for six months. The morphology and biochemical study was conducted by streaking isolated mixed culture in solid agar slant media and the cell shapes were identified by using an electron microscope. It was found that this mixed culture was gram‐negative for seven different isolates. The isolated strains were grown on substrates including methyl ethyl ketone (MEK), toluene, n‐butyl acetate, and o‐xylene (MTBX), as the carbon and energy sources. Among the seven isolates, an AKM 02 strain had a high MTBX‐degrading activity and was identified as Shewanella putrefaciens by taxonomical analysis, biochemical tests and 16S rDNA gene analysis methods. All isolates grew in a pH range from 3.0–11.0 with an optimum range of 6.0–8.0. In addition, each of the isolates grew in the temperature range of 15–45 °C with an optimum range between 25–30 °C. The batch experiments were conducted at four different initial MTBX concentrations ranging from 100–1000 mg L^–1. S. putrefaciens was capable of completely degrading n‐butyl acetate, MEK and toluene at a concentration lower than 500 mg L^–1. When the initial concentration of n‐butyl acetate, MEK and toluene were 500 mg L^–1, S. putrefaciens could remove the n‐butyl acetate, MEK and toluene completely within 70, 98 and 110 h, respectively. However, for o‐xylene at concentration of 500 mg L^–1, incomplete degradation was observed with only 70 % of the o‐xylene degraded after 135 h. Collectively, the results indicate that the S. putrefaciens strain degrades MTBX at a faster rate, and this strain can be used effectively in trickle‐bed air biofilters for treating high strength mixtures of paint solvents.     

Graft copolymerization of acrylic acid on methylcellulose by ceric ion/p‐xylene redox pair

The graft copolymerization of acrylic acid onto methylcellulose by ceric ion/p‐xylene redox pair was investigated in aqueous media under homogeneous conditions. The graft yield dependency on p‐xylene concentration in the range 1.8–45.0 × 10^?5M showed a minimum and an enhanced yield when the methylcellulose interacted with ceric ion and p‐xylene for an initial period of 10 min (preoxidation time) prior to addition of monomer to the reaction medium. This was attributed to the presence of two kinetically controlled reactions initiated by p‐xylyl radical and diradical species. At prolonged preoxidation times of 30 and 60 min, the graft yield dependency on p‐xylene concentration was normal and suggested the presence of only one initiating species. The effect of ceric ion on the graft reaction in the concentration range of 8.33–83.3 × 10^?3M was optimal at 131% graft yield for ceric ion concentration of 16.7 × 10^?3M and was reduced significantly by as much as 75% at the highest concentration of the latter. The temperature dependency of graft yield was negative in the region 30–50°C. At 50°C the initial rate of graft was only 37% of the value at 30°C. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 500–504, 2002; DOI 10.1002/app.10200     

Effects of the o‐aromatic ring in the molecular chain on the properties of polyester polyols

A series of liquid polyester polyols from adipic acid (AA), phthalic anhydride (PA), ethylene glycol, propanediol‐1,2, and trihydroxymethylpropane, varying in the molar ratio of PA to AA, were prepared. The effects of the o‐aromatic ring in the molecular chain, which came from PA, on the viscosity, glass‐transition temperature, and thermal degradation temperature of the polyester polyols were studied with viscometry, differential scanning calorimetry, and thermogravimetry. The intrinsic viscosity and glass‐transition temperature increased with the concentration of the o‐aromatic ring increasing. The temperature of the maximum thermal degradation rate for aliphatic polyester polyols was 434.20°C. Two steps of thermal degradation were found when there were o‐aromatic rings in the molecular chain. One thermal degradation temperature was 358.36–360.48°C, and the other was 412.85–427.18°C. Polyester polyols with o‐aromatic rings had higher stability at lower temperatures (<240.00°C). However, aliphatic polyester polyols had higher stability at higher temperatures (300.00–480.00°C). The activation energy and order of degradation were calculated from thermogravimetric curves. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1617–1624, 2002     

Dilute solution properties of hydroxyethyl starch

The dilute solution properties of hydroxyethyl starch (HES) were examined by using the techniques of osmometry, light scattering, and viscometry. The molecular weight range was approximately 2 × 10⁶–0.06 × 10⁶. Since HES is a branched molecule, its properties were compared with those of two linear counterparts, ethyl hydroxyethyl cellulose and hydroxyethyl cellulose. The branching index g was estimated to be about 0.3 when calculated from the intrinsic viscosity, radii of gyration, and second virial coefficients.     

Synthesis of poly(arylene benzimidazole) sulfone (PABIS) and preparation of hollow PABIS microspheres

4,4'‐Di(benzimidazolyl)benzene sulfone, as the monomer, is very readily available by the reaction of 4,4'‐dicarboxydiphenyl sulfone with o‐phenylenediamine, and poly(arylene benzimidazole) sulfone (PABIS) has been synthesized by the condensation polymerization of bis(4‐fluorophenyl) sulfone with di(benzimidazolyl)benzene sulfone via an N–C coupling reaction. The structure of the polymer was characterized by Fourier transform IR spectroscopy, ¹H NMR spectroscopy and elemental analysis, and the results showed agreement with the proposed structure. DSC and thermogravimetric measurements showed that PABIS possesses a high glass transition temperature (T_g = 321 °C) and good thermal stability with high decomposition temperature (T_d > 530 °C). Additionally, PABIS exhibits good solubility in most polar organic solvents. Based on the good chemical and physical properties, hollow PABIS microspheres with diameters in the range 0.3–1.8 mm were prepared by the micro‐liquid technique and the double‐layer latex technique. A new double T‐channel droplet generator was developed for continuous fabrication of controlled‐size hollow PABIS microspheres. The structures of the hollow PABIS microspheres were characterized, and they possessed equal wall thickness and good spherical symmetry. © 2013 Society of Chemical Industry     

Polyimides derived from 1,4‐bis [3‐oxy‐(N‐aminophthalimide)] benzene

A novel diamine, 1,4‐bis [3‐oxy‐(N‐aminophthalimide)] benzene (BOAPIB), was synthesized from 1,4‐bis [3‐oxy‐(N‐phenylphthalimide)] benzene and hydrazine. Its structure was determined via IR, ¹H NMR, and elemental analysis. A series of five‐member ring, hydrazine‐based polyimides were prepared from this diamine and various aromatic dianhydrides via one‐step polycondensation in p‐chlorophenol. The inherent viscosities of these polyimides were in the range of 0.17–0.61 dL/g. These polymers were soluble in polar aprotic solvents and phenols at room temperature. Thermogravimetric analysis (TGA) showed that the 5% weight‐loss temperatures of the polyimides were near 450°C in air and 500°C in nitrogen. Dynamic mechanical thermal analysis (DMTA) indicated that the glass‐transition temperatures (T_gs) of these polymers were in the range of 265–360°C. The wide‐angle X‐ray diffraction showed that all the polyimides were amorphous. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Epoxy–imide resins from N‐(4‐ and 3‐carboxyphenyl)trimellitimides. I. Adhesive and thermal properties

Epoxy–imide resins were obtained by curing Araldite GY 250 (diglycidyl ether of bisphenol‐A and epichlorohydrin; difunctional) and Araldite EPN 1138 (Novolac–epoxy resin; polyfunctional) with N‐(4‐ and 3‐carboxyphenyl)trimellitimides derived from 4‐ and 3‐aminobenzoic acids and trimellitic anhydride. The adhesive lap shear strength of epoxy–imide systems at room temperature and at 100, 125, and 150°C was determined on stainless‐steel substrates. Araldite GY 250‐based systems give a room‐temperature adhesive lap shear strength of about 23 MPa and 49–56% of the room‐temperature adhesive strength is retained at 150°C. Araldite EPN 1138‐based systems give a room‐temperature adhesive lap shear strength of 16–19 MPa and 100% retention of room‐temperature adhesive strength is observed at 150°C. Glass transition temperatures of the Araldite GY 250‐based systems are in the range of 132–139°C and those of the Araldite EPN 1138‐based systems are in the range of 158–170°C. All these systems are thermally stable up to 360°C. The char residues of Araldite GY 250‐ and Araldite EPN 1138‐based systems are in the range of 22–26% and 41–42% at 900°C, respectively. Araldite EPN 1138‐based systems show a higher retention of adhesive strength at 150°C and have higher thermal stability and T_g when compared to Araldite GY 250‐based systems. This has been attributed to the high crosslinking possible with Araldite EPN 1138‐based systems arising due to the polyfunctional nature of Araldite EPN 1138. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1729–1736, 2000     

Copolymerization and addition of styrene and N‐phenylmaleimide in the presence of nitroxide

The copolymerization and addition reaction of styrene (S) with N‐phenylmaleimide (PMI), either neat or in xylene, have been found to proceed at 125°C in the presence of 2,2,6,6‐tetramethylpiperidin‐1‐yloxy (TEMPO) radicals. TEMPO‐terminated alternating S‐PMI copolymers and comonomer adducts were obtained. The amounts of the low molecular weight compounds increased with the increasing content of PMI in the initial mixture. The reaction suggests formation of monofunctional unimolecular initiators. In the autopolymerization of neat comonomers, a mediating role of TEMPO was observed. The synthesized copolymers containing TEMPO end groups were used as macroinitiators to initiate polymerization of styrene. The molecular weight distributions of resulting poly(styrene‐alt‐N‐phenylmaleimide)‐block‐polystyrene copolymers indicated the presence of both low molecular weight termination products and some copolymer precursor. The copolymers and comonomer adducts were characterized using the nitrogen analysis, size‐exclusion chromatography (SEC), and NMR spectroscopy. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1093–1099, 2000     

Microwave Absorption of SiC/HfCxN1−x/C Ceramic Nanocomposites with HfCxN1−x‐Carbon Core–Shell Particles

The dielectric properties of high‐temperature stable single‐source precursor‐derived SiC/HfC_xN_1?x/C ceramic nanocomposites are determined by microwave absorption in the X‐band (8.2–12.4 GHz) at room temperature. The samples synthesized at 1700°C, denoted as SiC/5HfC_xN_1?x/C‐1700°C and SiC/15HfC_xN_1?x/C‐1700°C ceramics, comprising ≈ 1.3 and ≈ 4.2 vol% HfC_xN_1?x, respectively, show enhanced microwave absorption capability superior to hafnium‐free SiC/C‐1700°C. The minimum reflection loss of SiC/5HfC_xN_1?x/C‐1700°C and SiC/15HfC_xN_1?x/C‐1700°C are ?47 and ?32 dB, and the effective absorption bandwidth amount to 3.1 and 3.6 GHz, respectively. Segregated carbon, including graphitic carbon homogeneously dispersed in the SiC matrix and less ordered carbon deposited as a thin film on HfC_xN_1?x nanoparticles, accounts for the unique dielectric behavior of the SiC/HfC_xN_1?x/C ceramics. Due to their large reflection loss and their high chemical and temperature stability, SiC/5HfC_xN_1?x/C‐1700°C and SiC/15HfC_xN_1?x/C‐1700°C ceramics are promising candidate materials for electromagnetic interference applications in harsh environment.     

Transient and steady‐state conduction in ethyl cellulose (EC)–poly(methyl methacrylate) (PMMA) blends

Transient discharging currents and steady‐state conduction in solution‐grown ethyl cellulose (EC)–poly(methyl methacrylate) (PMMA) blends measured as a function of temperature (30–80 °C) and field strength (10–100 kV cm⁻¹) are reported. Transient currents are found to follow the Curie–VonSchweidler law, characterized by different slopes in short‐ and long‐time regions, having different decay constant values lying between 0.75–0.99, and 1.68–1.95. The corresponding activation energies are found to increase with time of measurement of discharge current. Isochronal characteristics (ie current versus temperature plots at constant times) constructed from the data seem to reveal a broad peak observed at 60 °C. The dependence of dark current at different temperatures (30–80 °C) in a metal (1)–EC–PMMA blend–metal (1)/(2) system on the applied voltage in the range 10–100 kV cm⁻¹ has also been studied; the current is found to be strongly temperature dependent. Dipole polarization and space charge resulting from trapping of injected charge carriers in energetically distributed traps and induced dipoles created because of the piling up of charge carriers at the phase boundary of the heterogeneous components of the blend are considered to account for the observed transient currents. The results of current–voltage measurement on blends are interpreted to show that the low‐field steady‐state conduction is ohmic in nature, and in high fields the charge carriers are generated by field‐assisted lowering of coulombic barriers at the traps and are conducted through the bulk of the material by a hopping process between the localized states by a Jonscher–Ansari Poole–Frenkel mechanism. The modified P–F barrier is calculated to be 1.89 × 10⁻¹⁹ J (1.18 eV), 1.92 × 10⁻¹⁹ J (1.20 eV) and 1.95 × 10⁻¹⁹ J (1.22 eV) for P₁, P₂ and P₃ blends, respectively. © 2000 Society of Chemical Industry     

Thermal degradation of poly(3‐hydroxybutyrate) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) as studied by TG,TG–FTIR,and Py–GC/MS

The thermal degradation kinetics of poly(3‐hydroxybutyrate) (PHB) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) [poly(HB–HV)] under nitrogen was studied by thermogravimetry (TG). The results show that the thermal degradation temperatures (T_o, T_p, and T_f) increased with an increasing heating rate (B). Poly(HB–HV) was thermally more stable than PHB because its thermal degradation temperatures, T_o(0), T_p(0), and T_f(0)—determined by extrapolation to B = 0°C/min—increased by 13°C–15°C over those of PHB. The thermal degradation mechanism of PHB and poly(HB–HV) under nitrogen were investigated with TG–FTIR and Py–GC/MS. The results show that the degradation products of PHB are mainly propene, 2‐butenoic acid, propenyl‐2‐butenoate and butyric‐2‐butenoate; whereas, those of poly(HB–HV) are mainly propene, 2‐butenoic acid, 2‐pentenoic acid, propenyl‐2‐butenoate, propenyl‐2‐pentenoate, butyric‐2‐butenoate, pentanoic‐2‐pentenoate, and CO₂. The degradation is probably initiated from the chain scission of the ester linkage. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1530–1536, 2003