Rheological properties of polystyrene blends with rigid ladderlike polyphenylsilsesquioxane

Polystyrene (PS) blends with rigid ladderlike polyphenylsilsesquioxane (PPSQ) were prepared by solution casting followed by hot pressing. The rheological properties of these blends were studied under dynamic shear and uniaxial elongation conditions. The loss modulus (G″) and dynamic shear viscosity (η*) of the 95/5 PP/PPSQ blend were slightly lower than those of pure PS at low frequencies (≤10^?2 rad/s). However, the storage modulus (G′), G″, and η* of the other blends (90/10, 85/15, and 80/20) were higher than those of pure PS and increased with PPSQ content. The η_E data demonstrated that PS/PPSQ blends exhibited slightly weaker (5% PPSQ) or much weaker (10% PPSQ) strain hardening than PS. In contrast, the 85/15 and 80/20 PP/PPSQ blends showed strain softening, and the extent of strain softening increased with PPSQ content. PS entanglements might have been reduced by the specific interactions between PS and PPSQ, which locally ordered some PS molecules in the 95/5 blend sample, because most of the PPSQ might have been well dispersed in the PS continuous phase, and only a few small PPSQ particles (～1.3 μm) were formed because of good miscibility. However, at high PPSQ contents (≥10%), many larger hard PPSQ particles were formed, which acted as fillers during the rheological measurements. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 706–713, 2005     

Crystallization behavior and hydrophilicity of poly(vinylidene fluoride)/poly(methyl methacrylate)/poly(vinyl pyrrolidone) ternary blends

Ternary blends composed of matrix polymer poly(vinylidene fluoride) (PVDF) with different proportions of poly(methyl methacrylate) (PMMA)/poly(vinyl pyrrolidone) (PVP) blends were prepared by melt mixing. The miscibility, crystallization behavior, mechanical properties and hydrophilicity of the ternary blends have been investigated. The high compatibility of PVDF/PMMA/PVP ternary blends is induced by strong interactions between the carbonyl groups of the PMMA/PVP blend and the CF₂ or CH₂ group of PVDF. According to the Fourier transform infrared and wide‐angle X‐ray difffraction analyses, the introduction of PMMA does not change the crystalline state (i.e. α phase) of PVDF. By contrast, the addition of PVP in the blends favors the transformation of the crystalline state of PVDF from non‐polar α to polar β phase. Moreover, the crystallinity of the PVDF/PMMA/PVP ternary blends also decreases compared with neat PVDF. Through mechanical analysis, the elongation at break of the blends significantly increases to more than six times that of neat PVDF. This confirms that the addition of the PMMA/PVP blend enhances the toughness of PVDF. Besides, the hydrophilicity of PVDF is remarkably improved by blending with PMMA/PVP; in particular when the content of PVP reaches 30 wt%, the water contact angle displays its lowest value which decreased from 91.4° to 51.0°. Copyright © 2011 Society of Chemical Industry     

Investigation on crystallization behavior and hydrophilicity of poly(vinylidene fluoride)/poly(methyl methacrylate)/poly(vinyl pyrrolidone) ternary blends by solution casting

Ternary blends composed of matrix polymer poly(vinylidene fluoride) (PVDF) with different proportions of poly(methyl methacrylate) (PMMA)/poly(vinyl pyrrolidone) (PVP) blends were prepared by solution casting. The crystallization behavior and hydrophilicity of ternary blends were characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), wide angle X‐ray diffraction (WAXD), differential scanning calorimetry (DSC), and contact angle test. According to morphological analysis, the surface was full of typical spherulitic structure of PVDF and the average diameter was in the order of 3 μm. The samples presented predominantly β phase of PVDF by solution casting. It indicated that the size of surface spherulites and crystalline phase had little change with the PMMA or PVP addition. Moreover, FTIR demonstrated special interactions among the ternary polymers, which led to the shift of the carbonyl stretching absorption band of PVP. On the other hand, the melting, crystallization temperature, and crystallinity of the blends had a little change compared with the neat PVDF in the first heating process. Except for the content of PVP containing 30 wt %, the crystallinity of PVDF decreased remarkably from 64% to 33% and the value of t_1/2 was not obtained. Besides, the hydrophilicity of PVDF was remarkably improved by blending with PMMA/PVP, especially when the content of PVP reached 30 wt %, the water contact angle displayed the lowest value which decreased from 98.8° to 51.0°. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Solvent effects on the miscibility of poly(methyl methacrylate)/poly(bisphenol a carbonate) blends

Blends of atactic or syndiotactic poly(methyl methacrylate) (designated as aPMMA or sPMMA) and poly(bisphenol A carbonate) (PC) were prepared from solution casting. Tetrahydrofuran (THF) and chloroform were used as solvent. Experimental results indicated that the as‐cast blends from THF were quite different from the chloroform‐cast ones. After film preparation, THF‐cast blends did not show any visible phase separation. However, chloroform‐cast blends formed a phase‐separated structure. The as‐cast PC from either solvent was not completely amorphous, and had a melting point at 239–242°C, indicating a certain degree of crystallinity. In contrast, the quenched samples of aPMMA/PC blends prepared from the two solvents behaved virtually the same. They both showed aPMMA dissolves better in PC, but PC solubility in aPMMA is very little. Using sPMMA instead of aPMMA to blend with PC, different results were obtained. The quenched sPMMA/PC blends cast from THF showed only one T_g. However, immiscibility (i.e., two T_gs) was found in the same blend system when cast from chloroform. THF was believed to cause the observation of single T_g due to the following kinetic reason. sPMMA and PC were still trapped together even after THF removal in a homogeneous, but nonequilibrium state below the glass transition. Therefore, the quenched sPMMA/PC blends were not truly thermodynamically miscible. From the results of aPMMA or sPMMA with PC, increasing syndiotacticity seemed to improve the miscibility between PMMA and PC. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2842–2850, 2001     

Phase behavior and properties of poly(methyl methacrylate)/poly(vinyl acetate) blends prepared via in situ polymerization

Polymer blends composed of poly(methyl methacrylate) (PMMA) and poly(vinyl acetate) (PVAc) were prepared via radical-initiated polymerization of methyl methacrylate (MMA) in the presence of PVAc. Differential scanning calorimetry and dynamic mechanical analysis were employed to investigate the miscibility and phase behavior of the blends. The PMMA/PVAc blends of in situ polymerization were found to be phase separated and exhibited a two-phase structure, although some chain transferring reaction between the components occurred. The phase separation resulted from the solvent effect of MMA during the in situ polymerization, which was confirmed by the investigation of phase behavior based on solution cast blending. Solubility analysis of the polymerized blends indicated that some chain transferring reaction between the components occurred during the polymerization. An abrupt increase in gel content from 21.2 to 72.4 wt % was observed when the inclusion of PVAc increased from 30 to 40 wt %, and the gel component consisted of the component polymers as shown by infrared spectroscopy studies. The thermogravimetric analysis study indicated that the inclusion of a small amount of PVAc gives rise to a marked stabilization effect on the thermal stability. The PMMA/PVAc blends exhibited increased notched impact properties with the inclusion of 5 wt % PVAc. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 675–684, 1998     

Morphological and infra-red studies on highly oriented poly(vinylidene fluoride)/poly(methyl methacrylate) blends

Highly oriented melt drawn films of poly(vinylidene fluoride) (PVDF) and blends of poly(vinylidene fluoride) and poly(methyl methacrylate) (PMMA) have been studied by transmission electron microscopy, electron diffraction and infra-red spectroscopy. Infra-red spectra show the second moment of the orientation function for PVDF samples to be greater than 0.94. Using such a sample, the transition dipole directions relative to the chain axis have been calculated. Electron microscopic studies of the PVDF/PMMA blends show a transformation for pure PVDF from a lamellar morphology to a mixture of lamellar and needle-like crystals for the 80/20 blend. The 60/40 blend shows a pure needle-like morphology. The β phase content for this blend is dependent upon the composition and thermal history. An increase in the β phase content is observed with the addition of PMMA. After annealing at 110°C, the 50/50 blend shows a lamellar β phase morphology. A significant increase in the segmental orientation of PVDF is also observed.     

Comparison of the phase behaviour of the liquid-crystalline polymer/poly(methyl methacrylate) and poly(vinyl acetate)/poly(methyl methacrylate) blends

The phase behaviour of blends of a liquid-crystalline polymer (LCP) and poly(methyl methacrylate) (PMMA), as well as the phase state of blends of PMMA and poly(vinyl acetate) (PVA) has been investigated using light scattering and phase-contrast optical microscopy. The blends of LCP and PMMA have been obtained by coagulation from ternary solutions. The cloud point curves were determined. It was established that both pairs demix upon heating, ie have an LCST. In the region of intermediate composition, the phase separation proceeds according to a spinodal mechanism; however for LCP/PMMA blends, the decomposition proceeds according to a non-linear regime from the very onset. In the region of small amounts of LCP, the phase separation follows a mechanism of nucleation and growth. For PMMA/PVA blends, the spinodal decomposition proceeds according to a linear regime, in spite of the molecular mobility that PVA chains develop at lower temperatures. Only after prolonged heat treatment does the process transit to a non-linear regime. The data show a similarity between the phase behaviour of blends of liquid-crystalline and of flexible amorphous polymers. The distinction consists of the absence of a linear regime of decomposition for LCP-PMMA blends. © 1999 Society of Chemical Industry     

Preparation of graded materials for miscible polycarbonate/poly(methyl methacrylate) blends by segregation under shear flow

Exposure to shear flow produced by a pressure-driven capillary rheometer provides a concentration gradient without phase separation in miscible polymer blends of bisphenol-A polycarbonate containing low-molecular-weight poly(methyl methacrylate) (PMMA). The strand surface extruded from the rheometer contains a large amount of PMMA. However, the strand is transparent because there is no light scattering due to phase separation. The segregation behavior, that is, enrichment of the PMMA content at the strand surface, is enhanced when the molecular weight of PMMA is low. Furthermore, the segregation is also enhanced at high temperatures and at high shear rates. By contrast, the die length barely affects the degree of segregation. The segregation phenomenon should be noted because it may facilitate the modification of the surface properties of various products.     

Structure and properties of highly stereoregular isotactic poly(methyl methacrylate) and syndiotactic poly(methyl methacrylate) blends treated with supercritical CO2

The structure and properties of highly stereoregular isotactic poly(methyl methacrylate) (it-PMMA) and syndiotactic poly(methyl methacrylate) (st-PMMA) blends with crystalline stereocomplex formed by supercritical CO₂ treatment at temperatures ranging from 35 to 130 °C were investigated by means of differential scanning calorimetry (DSC), wide-angle X-ray diffraction (WAXD), and dynamic mechanical analysis (DMA) measurements. The melting temperature, T_m, and the heat of fusion, ΔH_m, had maximum values at about 200 °C and 25 J/g, respectively. The degree of crystallinity evaluated by WAXD ranged in value from 32 to 38%. The fringed-micellar stereocomplex crystallites were formed in case of treatment temperatures below 90 °C, and the orderliness perpendicular to the helix axis of the fringed-micellar crystallites was considered to be increased with increasing treatment temperature. In case of treatment temperature of 130 °C, the fringed-micellar crystallites and the lamellar crystallites with high orderliness parallel to the helix axis coupled with the perpendicular orderliness were formed, and the respective double endothermic peaks, T_m¹ and T_m³, were observed in DSC due to the melting of the two kinds of stereocomplex crystallites. The it-PMMA/st-PMMA blends containing the fringed-micellar crystallites maintained high values of storage modulus, E′, up to higher temperature compared with the amorphous blends. The E′ of the blend treated with CO₂ at 130 °C decreased twice at temperatures corresponding to T_m¹ and T_m³.     

Miscibility of C60‐containing poly(methyl methacrylate)/poly(vinylidene fluoride) blends

The miscibility of C₆₀‐containing poly(methyl methacrylate) (PMMA‐C₆₀) with poly(vinylidene fluoride) (PVDF) was studied. Two PMMA‐C₆₀ samples containing 2.6 and 7.4 wt % C₆₀ were found to be miscible with PVDF based on single glass transition temperature criterion and melting point depression of PVDF. However, the interaction parameters of the two blend systems are less negative than that of the PMMA/PVDF blend system, showing that the incorporation of C₆₀ reduces the ability of carbonyl groups of PMMA to interact with PVDF. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1393–1396, 2000     

Synthesis and properties of poly(methyl methacrylate)/montmorillonite (PMMA/MMT) nanocomposites

PMMA/MMT nanocomposites were successfully synthesized via in situ intercalative polymerization, and characterized by means of wide‐angle X‐ray diffractometry, transmission electron microscopy, thermal gravimetric analysis, dynamic mechanical analysis and Fourier‐transform infrared analysis. The nanocomposites possess partially exfoliated and partially intercalated structure, in which the silicate layers are exfoliated into nanometre secondary particles with thickness of less than 20 nm and uniformly dispersed in the polymer matrix. In comparison with pure PMMA, the thermal stability, glass transition temperature, and mechanical properties of the polymer are notably improved by the presence of the nanometric silicate layers. It was found that part of the PMMA chains in the nanocomposites are well immobilized inside and/or onto the layered silicates and, therefore, the unique properties of the nanocomposites result from the strong interactions between the nanometric silicate layers and the polymer chains. Copyright © 2003 Society of Chemical Industry     

Interface and mechanical properties of poly(methyl methacrylate)–fiber composites

Long‐fiber pellets were made by an in situ pultrusion process. Fiber‐reinforced composites were prepared by an injection‐molding process and an extrusion/injection‐molding method with pellets, respectively. SEM observations showed that the strong interface was maintained during the injection process for low shearing forces, although polymer adhesion to the fiber surface was completely delaminated in the process of extrusion/injection molding for very high shearing forces. Enhanced adhesion of composites promoted substantial improvement of mechanical properties compared to those with poor adhesion. However, the enhanced adhesion between the fiber and the matrix also sacrificed the impact resistance properties. Longer fibers substantially enhanced the properties of composites. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2478–2483, 2004     

Effect of tacticity on the transition behaviour of poly(methyl methacrylate)/poly(vinyl chloride) blends. Thermally stimulated depolarization study

The transition behaviour of blends of poly(vinyl chloride) (PVC) and poly(methyl methacrylate) isotactic (i-PMMA) and syndiotactic (s-PMMA) was determined in the temperature range ?150°C to +130°C by the thermally stimulated depolarization currents method (TSDC). The evolution of the current spectra was analysed as a function of blend composition. From the variation of properties of the peaks (presence or not of two T_g peaks, shifting or not of their positions, existence or not of interfacial components, regular or complex variation of the peak amplitudes ...), it was concluded that i-PMMA and PVC form an incompatible system over the entire concentration range while in s-PMMA/PVC blends, some compatibility probably exists but only for concentrations in s-PMMA not higher than 10 wt%. By referring to literature data, this value is much smaller than the compatibility range found from d.s.c. and mechanical measurements but is close to that determined from optical and electronic spectroscopy methods. These results emphasize the important role played by the type of method used to find out compatibility of a given polymer pair and show that the TSDC technique may be particularly useful for studying the interfacial phenomena associated with phase separation owing to its exceptional ability for easily detecting Maxwell-Wagner-Sillars polarization generated by the trapping of charge carriers at phase boundaries.     

Viscoelastic properties of blends of poly(methyl methacrylate) and poly(styrene‐co‐acrylonitrile) having various acrylonitrile contents

Dynamic viscoelastic properties of blends of poly(methyl methacrylate) (PMMA) and poly(styrene‐co‐acrylonitrile) (SAN) with various AN contents were measured to evaluate the influence of SAN composition, consequently χ parameter, upon the melt rheology. PMMA/SAN blends were miscible and exhibited a terminal flow region characterized by Newtonian flow, when the acrylonitrile (AN) content of SAN ranges from 10 to 27 wt %. Whereas, PMMA/SAN blends were immiscible and exhibited a long time relaxation, when the AN content in SAN is less than several wt % or greater than 30 wt %. Correspondingly, melt rheology of the blends was characterized by the plots of storage modulus G′ against loss modulus G″. Log G′ versus log G″ plots exhibited a straight line of slope 2 for the miscible blends, but did not show a straight line for the immiscible blends because of their long time relaxation mechanism. The plateau modulus, determined as the storage modulus G′ in the plateau zone at the frequency where tan δ is at maximum, varied linearly with the AN content of SAN irrespective of blend miscibility. This result indicates that the additivity rule holds well for the entanglement molecular weights in miscible PMMA/SAN blends. However, the entanglement molecular weights in immiscible blends should have “apparent” values, because the above method to determine the plateau modulus is not applicable for the immiscible blends. Effect of χ parameter on the plateau modulus of the miscible blends could not be found. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Casting solvent effect on crystallization behavior and morphology of poly(ethylene oxide)/poly(methyl methacrylate)

Poly(ethylene oxide) (PEO)/poly(methyl methacrylate) (PMMA) blends were prepared by casting from either chloroform or benzene solvents. After casting from solvents, all samples used in this study were preheated to 100°C and held for 10 min. Then, the solvent effect on the crystallization behavior and thermodynamic properties were studied by differential scanning calorimeter (DSC). Also, the morphology of spherulite of casting film was studied by polarized optical microscope. From the DSC and polarizing optical microscopy (POM) results, it was found that PEO/PMMA was miscible in the molten state no matter which casting solvent was used. However, the crystallization of PEO in the chloroform‐cast blend was more easily suppressed than it was in the benzene‐cast blend. Relatively, the chloroform‐cast blend showed the greater melting‐point depressing of PEO crystals. Also, the spherulite of chloroform‐cast film showed a coarser birefringence. It was supposed that the chloroform‐cast blend had more homogeneous morphology. It is fair to say that polymer blends, cast from solvent, are not necessarily in equilibrium. However, the benzene‐cast blends still were not in equilibrium even after preheating at 100°C for 10 min. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1627–1636, 2000     

Fabrication and morphology control of poly(methyl methacrylate) hollow structures via coaxial electrospinning

A modified electrospinning method known as coaxial electrospinning was used to fabricate poly(methyl methacrylate) (PMMA) hollow structures. In this study to understand morphology control, the effect of processing parameters such as concentration of polymer sheath solution, size of core/sheath capillaries, feed rate, and applied voltage had been evaluated. Morphological observations via scanning electron microscope (SEM) revealed that via the control of polymer concentration within the sheath solution, morphologies such as hollow particles and fibers could be obtained. With the use of fine core/sheath capillaries, micron hollow fibers with walls of less than 20 nm were obtained. This study has demonstrated how the investigated processing parameters have a direct influence on the structures and how these parameters have supported the notion that effective encapsulation process is the key to the dual layer bicomponent structures. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

The effect of layered double hydroxides dispersion on thermal and mechanical properties of poly(vinyl chloride)/poly(methyl methacrylate) blends

Poly(vinyl chloride) (PVC)/layered double hydroxide (LDH) composites and PVC/poly(methyl methacrylate) (PMMA)/LDH composites were prepared via solution intercalation into PVC using both unmodified and organo‐modified LDHs and variable‐molecular‐weight PMMA as additional components. The LDH dispersion was investigated using X‐ray diffraction analysis and electron microscopy in scanning and transmission modes. Spotlight fourier transform infrared (FTIR) chemical imaging analysis was also used to obtain a deeper insight into the dispersion of polymer phases and LDH segregation. Thermal properties were determined using thermogravimetric analysis and differential scanning calorimetry; moreover, a preliminary investigation of mechanical properties in tensile mode and evaluation of the Vicat softening temperature were carried out. The morphological analysis of PVC/LDH and PVC/PMMA/LDH composites evidenced in both cases the presence of disordered micro‐aggregates with loss of the LDH crystallographic symmetry depending on the amount and molecular weight of PMMA. In particular, in the case of PVC/PMMA/LDH composites, the FTIR imaging analysis showed that PMMA mostly segregated in the LDH phase. However, even if the degree of LDH dispersion was not elevated (micro‐aggregates with disordered structures and size ranging from 0.5 up to 11 µm were evidenced), thermal stability and mechanical properties of the composites were improved with a synergic effect of PMMA and LDH. © 2013 Society of Chemical Industry     

Properties of mineral filled poly(lactic acid)/poly(methyl methacrylate) blend

This study examines the influence of three different minerals, that is, clay, calcium carbonate, and quartz on the physical, thermal, and mechanical properties of poly(lactic acid) (PLA)/poly(methyl methacrylate) blend. Rheological behavior and phase structure were initially studied by small-amplitude oscillatory shear rheology. Clay- and quartz-filled materials presented an increase in viscosity at low frequency associated with the presence of a yield stress. However, this behavior was not observed for calcium carbonate filled materials due to a matrix degradation effect. To elucidate this aspect, thermal stability and thermal properties were examined by thermogravimetric analysis and differential scanning calorimetry, showing that calcium carbonate promotes degradation of the PLA phase. No nucleating effect was observed in the presence of the minerals. Dynamical mechanical analysis and mechanical characterization revealed an increase of the overall softening temperature and, a reinforcing effect for clay- and quartz-based composites. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 46927.     

Electrospinning of cyclodextrin functionalized poly(methyl methacrylate) (PMMA) nanofibers

Cyclodextrin functionalized PMMA nanofibers (PMMA/CD) were successfully produced by electrospinning technique with the goal to develop functional nanowebs. Bead-free uniform electrospun PMMA/CD nanofibers were obtained from a homogeneous solution of CDs and PMMA in dimethylformamide (DMF) using three different types of CDs, α-CD, β-CD and γ-CD. The electrospinning conditions were optimized in order to form bead-free PMMA/CD nanofibers by varying the concentrations of PMMA and CDs in the solutions. The concentration of CDs was varied from 5% up to 50% w/w, with respect to the PMMA matrix. We find that the presence of the CDs in the PMMA solutions facilitates the electrospinning of bead-free nanofibers from the lower polymer concentrations and this behavior is attributed to the high conductivity and viscosity of the PMMA/CD solutions. The X-ray diffraction (XRD) spectra of PMMA/CD nanowebs did not show any significant diffraction peaks indicating that the CD molecules are homogeneously distributed within the PMMA matrix and does not form any phase separated crystalline aggregates. Furthermore, attenuated total reflection Fourier transform infrared (ATR-FTIR) studies elucidate that some CD molecules are located on the surface of the nanowebs. This suggests that these CD functionalized nanowebs may have the potential to be used as molecular filters and/or nanofilters for waste treatment purposes.     

Preparation of compatible blends of poly(methyl methacrylate) used in dentistry with a reactive terpolymer containing maleic anhydride and their thermomechanical characterization

This study focuses on the preparation of compatible blends with the poly(methyl methacrylate) (PMMA) using a reactive terpolymer maleic anhydride–styrene–vinyl acetate (MA–St–VA). In the first series of experiments, binary blends of the PMMA and the MA–St–VA terpolymer have been prepared in tetrahydrofurane. The PMMA and the MA–St–VA terpolymer formed the compatible blends. The effects on thermomechanical properties of MA–St–VA terpolymer ratio in the blends were studied. The glass transition temperatures (T_g), thermal expansion coefficient (α), and other thermomechanical parameters for the blends have been established by TMA method and the compatibility of two polymers has been evaluated by these TMA parameters. The addition of MA–St–VA terpolymer to PMMA made a plasticizing effect on PMMA. This effect regularly changed with the increasing of the terpolymer in the blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 363–367, 2006