数字同轴和数字离轴全息系统分析

利用最高空间频率分析法,通过逐点分析记录在 CCD 上的空间频率信息,研究了物体可允许记录的最大横向尺寸、最小记录距离、全息图的信息量、空间分辨力、再现像的横向分辨力、轴向分辨力及散斑大小,并得到了数学表达式。理论分析和实验结果表明,数字同轴全息系统放宽了对 CCD 分辨力的要求,有较高的分辨力,较低的散斑噪声、灵活、简单的系统结构及较高的 CCD 空间带宽利用率,在增强系统性能方面要优于数字离轴全息系统。这一研究为数字全息系统的设计和操作提供了一定的理论和实验指导。     

Quantitative phase microscopy using dual-plane in-line digital holography

We present detailed theoretical evaluation and thorough experimental investigation of quantitative phase imaging using our previously demonstrated dual-plane in-line digital holographic microscopy technique [Opt. Lett. 35, 3426 (2010)]. This evaluation is based on the recording of two interferograms at slightly different planes and numerically reconstructing the object information. The zero-order diffracted wave is eliminated by using the method of subtraction of average intensity of the entire hologram, and the twin-image diffracted wave is removed by Fourier domain processing of the two recorded holograms. Experiments are performed using controlled amplitude and phase objects and human muscle cells to demonstrate the potential of this technique.     

Coal powder measurement by digital holography with expanded measurement area

The field of view of digital in-line holography for flow field diagnostics is restricted to a small volume due to the finite size and the low spatial resolution of the available CCD. Expansion of the measurement cross section of digital holographic particle image velocimetry was investigated with a lens-based holography configuration. By sampling the chirp signal in the center lobe completely and undersampling the chirp signal in the second- and higher-order lobes by a magnified virtual recording plane produced by an imaging camera lens, the field of view is expanded. Simulation results show that the three-dimensional (3D) location and size of the relatively large particle can be reconstructed with good accuracy. A digital holographic particle image velocimetry system was established for coal particle flow field diagnostics. Compared with the lensless configuration, the field of view of the digital holography system was enlarged 1.9 times, up to 2.78 cm × 2.78 cm × 3 cm. The 3D location, size distribution, and the 3D vector field of coal powder were obtained. The results show that the application of digital in-line holography to measure large particle flow field is feasible.     

Surface shape measurement by phase-shifting digital holography with a wavelength shift

Surface contouring by phase-shifting digital holography is proposed and verified by experiments and numerical simulations. Digital holograms are recorded before and after mode hopping of a laser diode subject to current tuning, and the difference of the reconstructed phases at each wavelength is computed to deliver surface contours of a diffusely reflecting surface. Since normal incidence on the object is employed, the method does not need the removal of the tilt component and is free from the shadowing effect as advantages over the dual-incidence method proposed before by the first author.     

傅里叶变换同轴数字全息记录余弦变换谱系数

余弦变换广泛应用于图像和视频的压缩编码以及模式识别之中。余弦变换为实偶对称的傅里叶变换,把实偶对称物体传送到位于傅里叶变换透镜前焦面的空间光调制器上,采用单色均匀平面激光光波照射,则在后焦面上为光波复振幅分布为实偶对称物体的傅里叶变换,即为物体的余弦变换。由于余弦变换谱系数既有正实数又有负实数,提出了采用傅里叶变换同轴数字全息方法记录余弦变换谱系数,通过把数字全息图减去参考光光强和物光光强而得到余弦变换系数。理论推导和实验结果表明了该方法的可行性,该方法可应用于图像的快速余弦变换。     

Digital in-line holography of microspheres

We have used digital in-line holography (DIH) with numerical reconstruction to image micrometer-sized latex spheres as well as ferrimagnetic beads suspended in gelatin. We have examined in detail theoretically and experimentally the conditions necessary to achieve submicrometer resolution of holographic reconstructions. We found that both transparent and opaque particles could be imaged with a resolution that was limited only by the wavelength of the light used. Simple inspection of intensity profiles through a particle allowed an estimate to be made of the particle's three position coordinates within an accuracy of a few hundred nanometers. When the derivative of a second-order polynomial fitted to the intensity profiles was taken, the X, Y, Z position coordinates of particles could be determined within +/-50 nm. More-accurate positional resolution should be possible with the help of more-advanced computer averaging techniques. Because a single hologram can give information about a large collection of distributed particles, DIH offers the prospect of a powerful new tool for three-dimensional tracking of particles.     

Difference displacement measurement by digital holography by use of simulated wave fronts

A concept called fringe compensation was first presented in phase-shifting electronic speckle-pattern interferometry. We apply a similar principle to digital holographic interferometry; here the phase of a wave front is known and can be manipulated. The basic mathematical formulation of fringe compensation and some experimental results are shown with relatively large, simple rigid-body rotation and circular membrane deformation.     

Image formation in detuned interference-filter-aided in-line Fraunhofer holography

Detuned interference filters as Fourier processors can be used to enhance the poor fringe contrast often encountered with in-line Fraunhofer holography of small or many far-fields-away micro-objects. The subsequent effect on the reconstructed-image irradiance distribution is described. The modified aperture-limited image shape and size, and the possible consequences on the quantitative analysis are discussed.     

The collapse of micro cavitation bubbles

The inertia dominated collapse of micro cavitation bubbles in a viscous liquid with surface tension is investigated. In addition to the well known dramatic collapse mode, a smooth decrease of the void cavity is also possible due to the viscous damping. This effect is especially important for micro bubbles although the importance of surface tension increases strongly with decreasing initial radius. The collapse discussion can be performed easily without large numerical efforts by means of an analytical collapse criterion formulated by Bogoyavlenskiy. The results presented are relevant for cavitation theory and particular helpful for applications in microfluidic systems.     

Remote metrology by comparative digital holography

A method for the remote comparison of objects with regard to their shape or response to a load is presented. The method allows interferometric sensitivity for comparing objects with different microstructure. In contrast to the well-known incoherent techniques based on inverse fringe projection this new approach uses the coherent optical wave field of the master object as a mask for the illumination of the sample object. The coherent mask is created by digital holography to allow instant access to the complete optical information of the master object at any place desired. The mask is reconstructed by a spatial light modulator (SLM). The optical reconstruction of digital holograms with SLM technology allows modification of reconstructed wavefronts with respect to improvement of image quality, the skilled introduction of additional information about the object (augmented reality), and the alignment of the master and test object.     

Integrated gray-level gradient method applied for the extraction of three-dimensional velocity fields of sprays in in-line digital holography

In this study, an integrated gray-level gradient method is applied to extract the three-dimensional (3D) velocity fields of sprays. This method consists of a conventional edge-sharpness method and a new method, namely, the overall-sharpness method, which is an efficient supplement of the former. And then the synchronization system is designed and assembled to record double-exposure spray holograms in a short time interval. Finally, using the integrated gray-level gradient method and some image processing techniques, the 3D coordinates of droplets are easily obtained, which can be used to evaluate the 3D velocity fields and the size features of spray droplets in different spray injection pressures. It proves that the integrated gray-level gradient method is well applied to measure the characteristics of sprays in in-line digital holography.     

Three-dimensional angle measurement based on propagation vector analysis of digital holography

We propose what we believe to be a novel method for highly accurate three-dimensional (3D) angle measurement based on propagation vector analysis of digital holography. Three-dimensional rotations in space can be achieved by use of a CCD camera and a multifacet object, which reflects an incident wave into different directions. The propagation vectors of the reflected waves from the object can be extracted by analyzing the object spectrum of the recorded hologram. Any small rotation of the object will induce a change in the propagation vectors in space, which can then be used for 3D angle measurement. Experimental results are presented to verify the idea.     

Digital holography using a digital photo-camera

The possibilities of running digital holography using commonly available digital zoom photo-cameras are studied. A new modified method of the holographic set-up exploiting the properties of a photo-camera is suggested. This method offers a straightforward and simple way of both digital hologram recording and reconstructing. In order to verify the feasibility of the method, the holograms acquired are digitally reconstructed using a computer code based on the fast Fourier transform algorithm. Experimental results obtained are presented and discussed.     

Polarization imaging by use of digital holography

We present what we believe to be a new digital holographic imaging method that is able to determine simultaneously the distributions of intensity, phase, and polarization state at the surface of a specimen on the basis of a single image acquisition. Two reference waves with orthogonal polarization states interfere with the object wave to create a hologram that is recorded on a CCD camera. Two wave fronts, one for each perpendicular polarization state, are numerically reconstructed in intensity and phase. Combining the intensity and the phase distributions of these two wave fronts permits the determination of all the components of the Jones vector of the object-wave front. We show that this method can be used to image and measure the distribution of the polarization state at the surface of a specimen, and the obtained results indicate that precise quantitative measurements of the polarization state can be achieved. An application of the method to image the birefringence of a stressed polymethyl methacrylate sample is presented.     

Resolution analysis of a digital holography system

Although digital holography (DH) has many advantages compared to conventional holography, its resolution is limited due to CCDs or other recording devices. Three factors contribute to this limitation, namely, the pixel averaging effect within the finite detection size of one pixel, a finite CCD aperture size limitation, and the sampling effect due to a finite sampling interval. In this paper, interactions of the three factors on resolution are investigated and presented. The resolution of a DH system can be determined for given parameters of these three factors. The domains dominated by different factors are explained along with their accuracy. As a DH system is space variant, influences of object extent on resolution are also discussed. The resolution performance of in-line and off-axis systems is studied and examples of resolution determination for a practical system are provided.     

Surface roughness measurement and analysis of mechanical parts based on digital holography

We measure the surface roughness of the mechanical parts based on digital holography. A digital offaxis hologram recording setup for reflective samples is built. Firstly, the height reconstruction error 2.3% of the setup is calibrated by using the quartz step height standard (VLSISHS-880QC). Then, the standard scribed-line model and the grinding roughness specimen are selected as the test samples and their surface roughness are 0.095 6 μm and 0.025 3 μm, with errors 6.3%, 0.9%, respectively. The results are in good agreement with the given roughness parameters. At last, we also analyze the window effect of the filter on the roughness measurement value based on digital holography. In conclusion, the paper demonstrated effectively that the digital holography could provide the surface feature for the roughness measurement with high accuracy.     

Phase-error correction in digital holography

The quality of images computed from digital holograms or heterodyne array imaging is degraded by phase errors in the object and/or reference beams at the time of measurement. This paper describes computer simulations used to compare the performance of digital shearing laser interferometry and various sharpness metrics for the correction of such phase errors when imaging a diffuse object. These algorithms are intended for scenarios in which multiple holograms can be recorded with independent object speckle realizations and a static phase error. Algorithm performance is explored as a function of the number of available speckle realizations and signal-to-noise ratio (SNR). The performance of various sharpness metrics is examined in detail and is shown to vary widely. Under ideal conditions with >15 speckle realizations and high SNR, phase corrections better than lambda/50 root-mean-square (RMS) were obtained. Corrections better than lambda/10 RMS were obtained in the high SNR regime with as few as two speckle realizations and at object beam signal levels as low as 2.5 photons/speckle with six speckle realizations.     

Detection of surface strain by three-dimensional digital holography

Three-dimensional digital holography with three object-illuminating beams has been successfully used for the detection of surface strain in metallic objects. The optical setup that uses illuminating beams to irradiate the object from three directions means that all three object surface displacement components, x, y, and z, can be independently calculated and used to find the strain gradients on the surface. The results show the conversion of the complete surface displacement field into a surface strain field. The method is capable of measuring microstrains for out-of-plane surface displacements of less than 10 microm.