Novel Carbon Dioxide Microsensor Based on Tin Oxide Nanomaterial Doped With Copper Oxide

Carbon dioxide $({rm CO}_{2})$ is one of the major indicators of fire and therefore its measurement is very important for low-false-alarm fire detection and emissions monitoring. However, only a limited number of ${rm CO}_{2}$ sensing materials exist due to the high chemical stability of ${rm CO}_{2}$. In this work, a novel ${rm CO}_{2}$ microsensor based on nanocrystalline tin oxide $({rm SnO}_{2})$ doped with copper oxide (CuO) has been successfully demonstrated. The ${rm CuO}hbox{-}{rm SnO}_{2}$ based ${rm CO}_{2}$ microsensors are fabricated by means of microelectromechanical systems technology and sol-gel nanomaterial-synthesis processes. At a doping level of ${rm CuO}:{rm SnO}_{2} =1:8$ (molar ratio), the resistance of the sensor has a linear response to ${rm CO}_{2}$ concentrations for the range of 1% to 4% ${rm CO}_{2}$ in air at 450$^{circ}{rm C}$. This approach has demonstrated the use of ${rm SnO}_{2}$, typically used for the detection of reducing gases, in the detection of an oxidizing gas.      

Development of a High-k Pr $_{2}$O $_{3}$ Sensing Membrane for pH-ISFET Application

In order to develop a pH sensor having a good pH-sensing characteristic, electrolyte-insulator-semiconductor capacitors using a high-k Pr$_{2}$O$_{3}$ thin film as the sensing membrane were fabricated on silicon substrates by reactive radio frequency sputtering. The structural and morphological features of these films with annealing at various temperatures were studied by X-ray diffraction, atomic force microscopy, and X-ray photoelectron spectroscopy. The Pr$_{2}$O $_{3}$ sensing film after annealing at 900$;^{circ}$C is suggested to the increase in the interfacial SiO $_{2}$ and silicate formation, and the high surface roughness. Therefore, a physical vapor deposition Pr$_{2}$O $_{3}$ film is adopted as a new pH-sensing layer. The result produces a pH response of 52.9 mV/pH $({rm pH}=2hbox{--}12)$, a hysteresis voltage of 17.5 mV $({rm pH}=7 to 4 to 7to 10 to 7)$, and a drift rate of 2.15 mV/h (${rm pH}=7$ buffer solution).      

Effect of Factors on Coercivity in Sr–La–Co Sintered Ferrite Magnets

We varied the composition and sintering temperature of Sr–La–Co ferrite magnets to analyze the effects of various important factors on coercivity $(H_{rm cJ})$. We examined the effects of crystal grain size and distribution, the mechanism of magnetization reversal, the degree of crystal grain orientation (OD), and the anisotropy field $(H_{rm A})$ on $H_{rm cJ}$. We proposed an equation based on the experimental results that expresses the measured $H_{rm cJ}$ and considers these effects as $H_{rm cJ} = C_{rm t}(0.4/R_{rm h})$ OD $(H_{rm A} - H_{rm d} - H_{rm in})$, where $C_{rm t}, R_{rm h}, H_{rm d}$, and $H_{rm in}$ are the crystal grain size effects on $H_{rm cJ}$ of sintered magnet, rotational hysteresis integral corresponding to the mechanism of magnetization reversal, demagnetizing field of shape anisotropy, and interaction field between crystal grains, respectively. We found that apart from the volume ratio for single-domain crystal grains and $H_{rm A}$, the mechanism of magnetization reversal had significant effects on $H_{rm cJ}$ for Sr–La–Co sintered ferrite magnets.      

CMOS Microelectrode Array for Electrochemical Lab-on-a-Chip Applications

Microelectrode arrays (MEAs) offer numerous benefits over macroelectrodes due to their smaller sample size requirement, small form factor, low-power consumption, and higher sensitivity due to increased rates of mass transport. These features make MEAs well suited for microfluidic lab-on-a-chip applications. This paper presents two implementations of MEAs with and without an on chip potentiostat. We first describe an 8$,times,$ 8 array of 6 $mu{rm m}$ circular microelectrodes with center to center 37 $mu{rm m}$ spacing fabricated on silicon using conventional microfabrication techniques. Pads are provided for external connections to a potentiostat for electrochemical analysis. The second implementation is an individually addressable 32$,times,$32 array of 7 $mu{rm m}$ square microelectrodes with 37 $mu{rm m}$ center to center spacing on a CMOS chip with built-in very-large-scale integration potentiostat for electrochemical analysis. The integrated CMOS MEA is post processed at the die level to coat the exposed Al layers with Au. To verify microelectrode array behavior with individual addressability, cyclic voltammetry was performed using a potassium ferricyanide $({rm K} _{3}{rm Fe}({rm CN})_{6})$) solution.      

Optimization of Spin-Valve Structure NiFe/Cu/NiFe/IrMn for Planar Hall Effect Based Biochips

This paper deals with the planar Hall effect (PHE) of Ta(5)/NiFe$(t_{rm F})$/Cu(1.2)/NiFe$(t_{rm P})$/IrMn(15)/Ta(5) (nm) spin-valve structures. Experimental investigations are performed for 50 $mu$m$times hbox{50} mu$m junctions with various thicknesses of free layer ( $t_{rm F} = 4, 8, 10, 12, 16, 26$ nm) and pinned layer ($t_{rm P} = 1, 2, 6, 8, 9, 12$ nm). The results show that the thicker free layers, the higher PHE signal is observed. In addition, the thicker pinned layers lower PHE signal. The highest PHE sensitivity $S$ of 196 $mu$V/(kA/m) is obtained in the spin-valve configuration with $t_{rm F} = 26$ nm and $t_{bf P} = 1$ nm. The results are discussed in terms of the spin twist as well as to the coherent rotation of the magnetization in the individual ferromagnetic layers. This optimization is rather promising for the spintronic biochip developments.      

Magnetic Normal Modes in Squared Antidot Array With Circular Holes: A Combined Brillouin Light Scattering and Broadband Ferromagnetic Resonance Study

We present a combined experimental investigation of magnetic normal modes in an antidot lattice using both Brillouin light scattering and broadband ferromagnetic resonance. It was fabricated on a silicon substrate using optical ultraviolet lithography. The sample consisted of a 30-nm-thick ${rm Ni}_{80}{rm Fe}_{20}$ squared antidot array with circular holes whose diameter and edge-to-edge spacing are 250 and 150 nm, respectively. Experiments were performed as a function of the applied magnetic field $mu_{0}{rm H}_{rm ext}$ in the range from $-$100 to 100 mT, with ${rm H}_{rm ext}$ applied along both the square lattice axis and its diagonal. Several peaks were observed in both the Brillouin light scattering and ferromagnetic resonance spectra, and their evolution with the intensity and the direction of the applied field ${rm H}_{rm ext}$ was measured. Micromagnetic simulations enabled us to identify the modes in terms of their symmetry obtaining a good quantitative agreement with the measured frequencies. In addition, we show how the inhomogeneity of the internal field affected the properties of the magnetic eigenmodes and their localization in different regions of the antidot lattice.      

Comparison of Alternative Techniques for Characterizing Magnetostriction and Inverse Magnetostriction in Magnetic Thin Films

We compare the direct and inverse techniques of measuring magnetostriction in magnetic thin films. We chose a set of four magnetic thin film samples (Co$_{95}$Fe$_5$, Co$_{60}$Fe$_{20}$B$_{20}$, Ni$_{65}$Fe$_{15}$Co$_{20}$, and Ni$_{80}$Fe$_{20}$) for the measurements, representing positive and negative magnetostriction and having saturation magnetostriction of magnitudes ranging from $10^{-7}$ to $10^{-5}$. We made the direct measurements on a high-precision optical cantilever beam system, and we carried out the inverse magnetostriction measurements on a nondestructive inductive $Bhbox{-}H$ looper with three-point bending stage.      

Planar Optical Waveguide Evanescent Wave ${rm CO}_{2}$ Sensor Based on a Clad of Alstonia Scholaris Leaf Extract

An evanescent wave biosensor is designed and developed using a single mode planar optical waveguide based on a spin coated clad of leaf extract of Alstonia Scholaris. The fabricated sensor showed ${rm CO}_{2}$ concentration dependent response. The specialty of this sensor is that it can be used when stored at room temperature (25$~^{circ}{rm C}$) up to a maximum of 25–30 days with 90% retention of original sensitivity. These ${rm CO}_{2}$ sensing biochips showed good operational efficiency for 10 cycles. The planar optical waveguide is versatile, easy to fabricate and can be used for ppm level ${rm CO}_{2}$ measurement with good sensitivity. Cross sensitivity with respect to humidity is studied. The sensor exhibited a short response time of 4–5 s and recovery time of 25 s with good repeatability and reproducibility.      

Thermal Diffusivity and Related Properties of Colossal Magnetoresistive La$_{0.67}$Ca$_{0.33}$MnO $_{3}$ With Various Grain Sizes

Using the open-cell photoacoustic technique, we have measured the room-temperature thermal diffusivities of the colossal magnetoresistive material La$_{0.67}$Ca$_{0.33}$MnO$_{3 }$, sintered between 1100$;^{circ}$ C and 1350$;^{circ}$ C, with average grain sizes 1, 3, 5, and 10 $mu$m. We obtained the thermal diffusivities by analyzing the phase of photoacoustic signals in thermally thick samples using Calderon's method. We found that the insulator-metal transition temperature does not depend on the grain size ($T_{rm IM} sim 272$ K). However, the thermal diffusivity increases with grain size, with values between 0.431 and 0.969 mm $^{2}$s $^{-1}$. Other related electrical and thermal properties, including the electrical conductivity, thermal conductivity, and phonon mean free path, are also dependent on the grain size. The electronic contribution to the thermal conductivity is 2%–3% of the total thermal conductivity for smaller grain sizes (1–5 $mu$m) and increases to about 24% when the grain size is increased to 10 $mu$ m.      

Measurement of Rapid Temperature Profiles Using Thermoluminescent Microparticles

The thermal history of a material with initially filled trap states may be probed using thermoluminescence. Since luminescent microparticles are composed of robust oxides, they are viable candidates for sensing temperature under conditions where all other types of direct-contact sensors fail. ${rm Mg}_{2}{rm SiO}_{4}:{rm Tb},{rm Co}$ particles with two thermoluminescent peaks have been heated using micromachined heaters over a 232 $~^{circ} hbox{C}$ to 313 $~^{circ} hbox{C}$ range on time scales of less than 200 ms. The effect of maximum temperature during excitation on the intensity ratio of the two luminescent peaks has been compared with first-order kinetics theory and shown to match within an average error of 4.4%.      

Full Wheatstone Bridge Spin-Valve Based Sensors for IC Currents Monitoring

Full Wheatstone bridge spin-valve-based electrical current sensors at the IC level are presented. Prototypes with different geometrical parameters have been designed, fabricated and fully characterized. DC characterization has been carried out, for measurement of insertion losses, linearity, voltage offset and sensitivity. Current ranges from 10 $mu{rm A}$ to 100 mA can be covered with these sensors with excellent linearity and sensitivities above 1 ${rm mV}/({rm V}cdot{rm mA})$ . AC characteristics have also been analyzed and bandwidths exceeding 100 kHz are demonstrated. Moreover, the temperature coefficients have been extracted in the range of $-20^{circ}{rm C}$ to $+60^{circ}{rm C}$. In order to highlight the design properties, dependence of the sensor's performance with external magnetic perturbations and self-heating have also been measured and quantified. The associated errors are in the range of 1%–2% of the full scale.      

Modeling and Simulation of a Single Tin Dioxide Nanobelt FET for Chemical Sensors

This paper presents the modeling and simulation of a tin dioxide (${rm SnO}_{2}$) field-effect transistor (FET)-based nanobelt gas sensor. The model results are compared to numerical simulations and experimental data obtained from published results describing the fabrication of single crystal nanobelts grown through thermal evaporation techniques. The fabricated sensor shows good response when exposed to oxygen (${rm O} _{2}$) and hydrogen (${rm H} _{2}$) at room temperature. Gas adsorption causes changes in the electrical contacts due to oxygen vacancies in the bulk. As a result, the ${rm I}$ -${rm V}$ characteristics are very different when the device is exposed to (${rm O} _{2}$) versus (${rm H} _{2}$ ). In the presence of ${rm H} _{2}$, the behavior of the contacts is ohmic and saturation is caused by pinch-off of the channel at the drain contact. However, in the presence of ${rm O} _{2}$ , the behavior of the contacts is Schottky, and device saturation occurs at the source end of the device. Our model is based on a depletion mode MOSFET and it accounts for both ohmic and Schottky contacts when the device is exposed to oxygen or hydrogen. It also provides a possible explanation for the gate bias dependence of the saturation current seen in some published characterization data.      

Magnetotransistor Based on the Carrier Recombination—Deflection Effect

This paper presents the three-terminal magnetotransistor based on the carrier recombination—deflection effect. Three-terminal magnetotransistor can detect vertical and lateral magnetic field direction. The structure of magnetotransistor consists of one emitter, one collector and one base contact. The devices can detect magnetic field by relying on the difference between base current and collector current $(Delta{rm I}_{rm CB})$. The result from experiments closely matched the simulated 3-D modeling with base width of 20 $mu{hbox {m}}$ at substrate thickness of 600 $mu{hbox {m}}$ . From the experiment, the magnetotransistor had the highest sensitivity of 10.25%/T when emitter current was at 10 mA. This research on the three-terminal magnetotransistor can achieve magnetic sensors with small size, high performance and wide range of applications.      

Establishment of All Digital Closed-Loop Interferometric Fiber-Optic Gyroscope and Scale Factor Comparison for Open-Loop and All Digital Closed-Loop Configurations

This paper covers the design details of an all digital closed-loop interferometric fiber-optic gyroscope (ADCL-IFOG) prototype, constructed in TUBITAK UME, and scale factor comparison between open-loop and ADCL-IFOG prototypes with sine wave biasing modulation. The output of demodulation circuit, proportional to the applied rotation rate, was sampled by AD7714YN analog-to-digital converter (ADC), operated in 16 bit resolution. Error voltage, generated by microcomputer – controlled LTC 1667CG, 14 bit digital to analog converter (DAC), was sent to the phase modulator through a linear summing circuit to make Sagnac Phase Shift zero, depending on the rotation direction. For this implementation, the ultimate rotation rate of 1.84 ($^{circ}/{hbox{h}}$ ) was nullified. The averaged sensitivity of the proposed closed-loop IFOG in unit of error voltage applied to the phase modulator was determined as 132.65 $mu hbox{V}/(^{circ}/{hbox{h}}$ ). The scale factors of both the open-loop and ADCL-IFOG prototypes were compared in a range of 1–15270 ( $^{circ}/hbox{h}$) rotation rate, corresponding to Sagnac Phase Shifts varying from 0.00115 ( $^{circ}$) to 17.57448 ( $^{circ}$). The maximum peak to peak noise and the bias stability of ADCL-IFOG prototype were determined as 4.97 ($^{circ}/hbox{h}$ ) and 1.48 ($^{circ}/hbox{h}$ ) at 23.0$~^{circ}hbox{C}$ , respectively.      

Microstructure, Electrical, and Magnetic Properties of ZrO$_{2}$ Added MnZn Ferrites

We investigated the influence of ZrO$_{2}$ on the microstructure and electromagnetic properties of MnZn ferrites by characterizing fracture surface micrographs, magnetic properties, and dc resistivity. Powders of Mn $_{0.68}$Zn $_{0.25}$Fe $_{2.07}$O $_{4}$ composition were prepared by the conventional ceramic technique. Toroidal cores were sintered at 1350 $^{circ}$C for 4 h in N$_{2}$/O$_{2}$ atmosphere with 4% oxygen. The results show that the lattice constant and average grain size increase with ZrO$_{2}$ concentration, but excessive ZrO $_{2}$ concentration will result in exaggerated grain growth and porosity increase. The dc resistivity, activation energy, saturation magnetic flux density, and initial magnetic permeability increase monotonically when the ZrO$_{2}$ concentration is not more than 0.04 wt% and then decrease with further increase of ZrO$_{2}$ concentration. On the other hand, the porosity, drift mobility, resonance frequency, and core loss decrease initially and then increase with the increase of ZrO$_{2}$ concentration.      

Effects of Post-Deposition Annealing and Oxygen Content on the Structural and pH-Sensitive Properties of Thin Nd $_{2}$O $_{3}$ Films

This paper describes the structural properties and sensing characteristics of thin Nd$_{2}$O$_{3}$ sensing membranes deposited on silicon substrates by means of reactive sputtering. X-ray diffraction, X-ray photoelectron spectroscopy, and atomic-force microscopy were used to study the chemical and morphological features of these films as functions of the growth conditions (argon-to-oxygen flow ratios of $20/5, 15/10$ and $10/15$; temperatures ranging from 600$~^{circ}$C to 800$~^{circ}$C). The thin Nd$_{2}$O$_{3}$ electrolyte-insulator-semiconductor devices prepared under a 15/10 flow ratio with subsequent annealing at 700$~^{circ}$C exhibited a higher sensitivity (56.01 mV/pH, in the solutions from pH 2 to 12), a smaller hysteresis voltage (4.7 mV in the pH loop $7 to 4 to 7to 10 to 7$), and a lower drift rate (0.41 mV/h in the pH 7 buffer solution) than did those prepared at the other conditions. We attribute this behavior to the optimal oxygen content in this oxide film forming a high density of binding sites and a small surface roughness.      

Correlation Between the Degradation of Perpendicular Anisotropy and the Double Hysteresis Behavior in [Pd/Co]$_{rm n}$/FeMn Exchange Biased Thin Films

We clearly detected double hysteresis by increasing Co layer thickness and decreasing the number of bilayers in perpendicular exchange biased [Pd(0.6)/Co$(t)$] $_{rm n}$/FeMn(11.6 nm) thin films. In-plane tensile stress calculations confirmed that the appearance of double hysteresis is closely related to the degradation of stress-induced perpendicular anisotropy in the [Pd/Co] multilayers. Furthermore, annealing at the magnetic field applied perpendicular to the film plane directly verified that the enhancement of thermally induced perpendicular anisotropy, $K_{rm eff-induced}$, in the [Pd/Co] multilayers is the main physical reason for removal of the double hysteresis. All our experimental and theoretical results demonstrated that perpendicular anisotropy is the dominant factor in controlling the double hysteresis behavior of perpendicularly magnetized [Pd/Co]$_{rm n}$/FeMn exchange biased thin films.      

A Microbolometer Asynchronous Dynamic Vision Sensor for LWIR

In this paper, a novel event-based dynamic IR vision sensor is presented. The device combines an uncooled microbolometer array with biology-inspired (“neuromorphic”) readout circuitry to implement an asynchronous, “spiking” vision sensor for the 8–15 $mu{rm m}$ thermal infrared spectral range. The sensor's autonomous pixels independently respond to changes in thermal IR radiation and communicate detected variations in the form of asynchronous “address-events.” The 64 $times$ 64 pixel ROIC chip has been fabricated in a 0.35 $mu{rm m}$ 2P4M standard CMOS process, covers about $4times 4 {rm mm}^{2}$ of silicon area and consumes 8 mW of power. An amorphous silicon (a-Si) microbolometer array has been processed on top of the ROIC and contacted to the pixel circuits. We discuss the bolometer detector properties, describe the pixel circuits and the implemented sensor architecture, and show measurement results of the readout circuits. Subsequently, a DFT-based approach to the characterization of asynchronous, spiking sensor arrays is discussed and applied. Test results and analysis of sensitivity, bandwidth, and noise of the fabricated IR sensor prototype are presented.      

Structure and Magnetic Properties of Sn$_{1 - {rm x}}$ Co$_{rm x}$ O$_{2}$ Powder and Film

We have studied room-temperature ferromagnetism (RTFM) in Sn$_{1 - {rm x}}$Co$_{rm x}$O$_{2}$ powders and films fabricated by the sol-gel method. Our X-ray diffraction, high-resolution transmission microscopy, and X-ray photoelectron spectroscopy results show that all the samples have a pure rutile structure, and Co ions have a chemical valence of 2+. In addition, the magnetic moment per Co ion drops rapidly with the increase of Co content. Interestingly, Sn $_{1 - {rm x}}$Co $_{rm x}$O $_{2}$ films spin-coated on a Si (111) substrate have much larger magnetic moment than powder samples, because film samples have larger domain volumes, which may induce stronger long-range magnetic exchange coupling.      

Electromagnetic Forces Acting on the Planar Armature of a Core-Type Synchronous Permanent-Magnet Planar Motor

The core-type synchronous permanent-magnet planar motor (SPMPM) discussed in this paper includes one or more planar armatures each of which contains two sets of three-phase windings named ${rm x}$-winding and ${rm y}$-winding. For each planar armature, a magnetic field energy equation is established first. This equation describes the mechanism of the coupling between the permanent-magnet array, the ${rm x}$-winding and the ${rm y}$ -winding in the core-type SPMPM. By using virtual work principle, ${rm x}$-direction thrust force, ${rm y}$ -direction thrust force and vertical force acting on the planar armature are modeling analytically. For eliminating the coupling in these force models, the excitation flux linkages and phase currents are all transformed into ${rm d}hbox{-}{rm q}$ synchronous reference frame. From the decoupling force equations, some characteristics of the vertical component of force on the planar armature are obtained. The electromagnetic force model is helpful for the design of the contactless planar bearing and the servo control system of the SPMPM.