A study on hydrogen storage and electrochemical properties of La_（0.55）Pr_（0.05）Nd_（0.15）Mg_（0.25）Ni_（3.5） （Co_（0.5）Al_（0.5））_x （x=0.0, 0.1, 0.3, 0.5） alloys

The La0.55Pr0.05Nd0.15Mg0.25Ni3.5(Co0.5Al0.5)x(x=0.0, 0.1, 0.3, 0.5) alloys were prepared by magnetic levitation melting under an Ar atmosphere, and the effects of Co and Al on the hydrogen storage and electrochemical properties were systematically investigated by pressure composition isotherms, cyclic voltammetry, Tafel polarization and electrochemical impedance spectroscopy testing. The results showed that the alloy phases were mainly consisted of (La,Pr)(Ni,Co)5, LaMg2Ni9, (La,Nd)2Ni7 and LaNi3 phases, and the cell volumes of (La,Pr)(Ni,Co)5, LaMg2Ni9, (La,Nd)2Ni7 and LaNi3 phases expanded with Co and Al element added. The hydrogen storage capacity initially increased from 1.36 (x=0) to 1.47 wt.% (x=0.3) and then decreased to 1.22 wt.% (x=0.5). The discharge capacity retention and cycle stability of the alloy electrodes were improved with the increase of Co and Al contents. The La0.55Pr0.05Nd0.15Mg0.25Ni3.5(Co0.5Al0.5)0.3 alloy electrode possessed better electrochemical kinetic characteristic.     

Phase structure and hydrogen storage properties of LaMg3.93Ni0.21 alloy

The phase structure and hydrogen storage property of LaMg3.93Ni0.21 alloy were studied.XRD and SEM results exhibited that LaMg3.93Ni0.21 alloy consisted mainly of LaMg3,La2Mg17 and LaMg2Ni phases;after hydriding/dehydriding process,all the three phases transformed,La3H7 phase existed and the actual hydrogen absorption phases were Mg and Mg2Ni phases.Pressure-composition-temperature (P-C-T)measurement showed that the reversible hydrogen storage capacity of LaMg3.93Ni0.21 alloy was 2.63 wt.%,and the absorption time for reaching 90%of the storage capacity was 124 s at 523 K,and it was 1850 s for deabsorbing 90%of the maximum dehydrogen capacity.The hydriding process of LaMg3.93Ni0.21 alloy followed the nucleation and growth mechanisms.The enthalpy and entropy for hydriding and dehydriding reactions of the Mg phase in LaMg3.93Ni0.21 alloy were calculated to be-66.38±1.10 kJ/mol H2,-100.96±1.96 J/(K·mol)H2 and 68.50±3.87 kJ/mol H2,98.28±5.48 J/(K·mol)H2,respectively.A comparison of these data with those of MgH2(-74.50 kJ/mol H2,-132.30 J/K·mol H2)suggested that the hydride of LaMg3.93Ni0.21 alloy was less stable than MgH2.The existence of La hydride and synergetic effect of multiphase led to higher reversible hydrogen storage capacity and better kinetic property at lower temperature for LaMg3.93Ni0.21 alloy.     

Structure and electrochemical hydrogen storage characteristics of the as-cast and annealed La0.8-xSmxMg0.2Ni3.15Co0.2Al0.1Si0.05 （x=0-0.4） alloys

In order to ameliorate the electrochemical cycle stability of the RE-Mg-Ni based A2B7-type electrode alloys, the Mg content in the alloy was reduced and La in the alloy was partially substituted by Sm. The La0.8-xSmxMg0.2Ni3.15Co0.2Al0.1Si0.05 (x=0, 0.1, 0.2, 0.3, 0.4) elec-trode alloys were fabricated by casting and annealing. The microstructures of the as-cast and annealed alloys were characterized by XRD and SEM. The electrochemical hydrogen storage characteristics of the as-cast and annealed alloys were measured. The results revealed that all of the experimental alloys mainly consisted of two phases: (La,Mg)2Ni7 phase with the hexagonal Ce2Ni7-type structure and LaNi5 phase with the hexagonal CaCu5-type structure. As Sm content grew from 0 to 0.4, the discharge capacity and the high rate discharge ability (HRD) first in-creased and then decreased for the as-cast and annealed alloys, whereas the capacity retaining rate (S100) after 100 cycles increased continuously.     

Investigations on hydrogen storage properties of LaMg8.52Ni2.23M0.15 （M=Ni, Cu, Cr） alloys

LaMg8.52Ni2.23M0.15 (M=Ni, Cu, Cr) alloys were prepared by induction melting. X-ray diffraction showed that all the three alloys had a multiphase structure, consisting of La2Mg17, LaMg2Ni and Mg2Ni phases. Energy dispersive X-ray spectrometer results revealed that most of Cu and Cr distributed in Mg2Ni phase. La2Mg17 and LaMg2Ni phases decomposed into MgH2, Mg2NiH4 and LaH3 phases during the hydrogenation process. Hydriding/dehydriding measurements indicated that the reversible hydrogen storage capacities of Mg2Ni phase in LaMg8.52Ni2.23M0.15 (M=Cu, Cr) alloys increased to 1.05 wt.% and 0.97 wt.% from 0.79 wt.% of Mg2Ni phase in LaMg8.52Ni2.38 alloy at 523 K. Partial substitution of Cu and Cr for Ni decreased the onset dehydrogenation temperature of the alloy hydrides and the temperature lowered by 18.20 and 5.50 K, respectively. The improvement in the dehydrogenation property of the alloys was attributed to that Cu and Cr decreased the stability of Mg2NiH4 phase.     

Influence of lanthanon hydride catalysts on hydrogen storage properties of sodium alanates

NaAlH4 complex hydrides doped with lanthanon hydrides were prepared by hydrogenation of the ball-milled NaH/Al+ xmol.% RE-H composites (RE=La,Ce;x=2,4,6) using NaH and Al powder as raw materials. The influence of lanthanon hydride catalysts on the hydriding and dehydriding behaviors of the as-synthesized composites were investigated. It was found that the composite doped with 2 mol.% LaH3.01 displayed the highest hydrogen absorption capacity of 4.78 wt.% and desorption capacity of 4.66 wt.%, respectively. Moreover, the composite doped with 6 mol% CeH 2.51 showed the best hydriding/dehydriding reaction kinetics. The proposed catalytic mechanism for reversible hydrogen storage properties of the composite was attributed to the presence of active LaH3.01 and CeH2.51 particles, which were scattering on the surface of NaH and Al particles, acting as the catalytic active sites for hydrogen diffusion and playing an important catalytic role in the improved hydriding/dehydriding reaction.     

Effect of substitution of aluminum for nickel on electrochemical properties of La_(0.75)Mg_(0.25)Ni_(3.5–x)Co_(0.2)Al_x hydrogen storage alloys

La0.75Mg0.25Ni3.5–xCo0.2Alx (x=0–0.09) hydrogen storage alloys were prepared by induction melting and effect of Al substitution for Ni on phase constitution and electrochemical property was investigated.With the substitution of Al for Ni,LaNi5 and LaNi2 phases occurred and (La,Mg)2(Ni,Co,Al)7 phase with hexagonal Ce2Ni7-type structure replaced (La,Mg)2(Ni,Co)7 phase.The cell volumes of LaNi5 and (La,Mg)2(Ni,Co,Al)7 main phases increased with increasing Al content.Some electrochemical properties and kinetic parameters of the alloys,including discharge capacity,high rate discharge ability (HRD),loss angle (ψ),exchange current density (I0) and limiting current density (IL),decreased with increasing amount of substitution of Al for Ni.Substitution of Al for Ni could be favorable for positive shift in corrosion potential of the alloy electrode,and prolonged cyclic lifetime of La0.75Mg0.25Ni3.5–xCo0.2Alx (x=0–0.09) alloy electrodes.     

Preparation and Structure of Mg2-xRExNi （RE = La, Ce, Pr, Nd, Y） Ternary Alloys

A series of Mg2-xNdxNi (x =0.05, 0.1, 0.2, 0.3) alloys and Mg1.95RE0.05Ni (RE= La, Ce, Pr, Nd, Y)ternary alloys were prepared by ball milling of mixted powder of Mg, Ni, RE and sintering under the protection of argon. XRD analysis shows that Mg2-xNdxNi (x = 0.05, 0.1 ) and Mg1.95RE0.05Ni consist of single phase with the same crystal structure as Mg2Ni. While three-phase alloys including Mg2Ni, NdNi and NdMgNi4 were formed in Mg1.8Nd0.2Ni and Mg1.7Nd0.3Ni alloys respectively. The lattice constants of Mg2Ni in those ternary alloys were calculated. The decomposition of Mg2Ni occurs in the milling process of Mg2Ni and Mg1.95RE0.05Ni alloys respectively. For the latter, another earlier reaction occurs in milling process, which means that atoms of RE are separated from crystal structure of Mg2Ni and form relevant oxides by combination with oxygen existed in argon atmosphere.     

Hydrogen storage properties of mechanically milled La2Mg17-x wt.% Ni （x=0, 50, 100, 150 and 200） composites

Melting method was used to obtain La2Mg17 alloy,and then Ni powder was added by mechanical alloying method.The kinetics of hydriding process and electrochemical properties of La2Mg17-x wt.%Ni(x=0,50,100,150,200) composites were investigated.X-ray diffraction(XRD) and scanning electron microscopy(SEM) analyses showed that the crystal structure of composite alloy gradually transformed into amorphous phase by the effect of ball milling and Ni powders.The research of hydrogen absorption properties found that La2Mg 17-50 wt.%Ni reached the highest hydrogen absorption than other alloys with more addition of Ni content,reached to 5.796 wt.% at 3 MPa,and up to 5.229 wt.% merely in 2 min,which revealed that the amorphous phase reduced the H occupation of the lattice clearance,resulting in the decline of hydrogen absorption capacity.The electrochemical tests indicated that the maximum discharge capacity increased to 353.1 mAh/g at 30 oC,however,the cycle stability decreased considerably.A series of kinetic measurements demonstrated that the controlling steps of electrochemical process of La 2 Mg 17-x wt.%Ni alloys transferred from hydrogen diffusion on alloy bulk(x=50,100) to hydrogen diffusion on both alloy bulk and surface(x=150,200).     

Study on structure and electrochemical properties of the （LaGdMg）Ni3.35-xCoxAl0.15（x=0-2.0） hydrogen storage alloys

Hydrogen storage alloys(LaGdMg)Ni3.35-xCoxAl0.15(x=0,0.1,0.3,0.5,1.0,1.5,2.0) were prepared by induction melting followed by annealing treatment in argon atmosphere.The effects of partly replacing Ni by Co element in(LaGdMg)Ni3.35Al0.15 on the phase structure and electrochemical properties of(LaGdMg)Ni3.35-xCoxAl0.15 alloys were investigated.Structure analysis showed that the alloys consisted of Ce2Ni7-type(Gd2Co7-type),CaCu5-type,Pr5Co19-type,PuNi3-type phase structure.The addition of Co element obviously reduced the contents of CaCu5-type phase and increased the contents of Ce2Ni7-type phase.However,Pr5Co19-type and CaCu5-type phase obviously increased with the high content of Co.Rietveld analysis showed that the c-axis lattice parameters and cell volumes of the component phases increased with increasing Co content.The electrochemical measurements showed that as the Co content increased,the maximum discharge capacity and the cyclic stability of the annealed alloys both first increased then decreased.The(LaGdMg)Ni3.05Co0.3Al0.15 alloy electrode exhibited the maximum discharge capacity(392.92 mAh/g),and the(LaGdMg)Ni1.85Co1.0Al0.15 alloy electrode showed the best cyclic stability(S100=96.1%).     

Influence of melt spinning and annealing treatment on structures and hydrogen storage thermodynamic properties of La0.8Pr0.2MgNi3.6Co0.4 alloy

La0.8Pr0.2MgNi3.6Co0.4 alloys were prepared by induction melting,annealing and melt spinning techniques.The influences of annealing treatment and melt spinning on phase structure and hydrogen storage properties were systematically investigated.The results of X-ray diffraction determine that the as-cast and as-spun La0.8Pr0.2MgNi3.6Co0.4 alloys consist of LaMgNi4 and LaNi5 phases,while only LaMgNi4 phase is present in the as-annealed alloy.The scanning electron microscope images illustrate that the grain of the alloy is significantly refined by melt spin ning tech no logy.The gaseous hydrogen storage kinetic and thermodynamic properties were measured by using a Sievert's apparatus at different temperatures.The maximum hydrogen storage capacity of the as-cast,as?spun and as-annealed La0.8Pr0.2MgNi3.6Co0.4 alloy is 1.699,1.637 and 1.535 wt.% at 373 K and 3 MPa,respectively.The annealed alloy has flatter and wider pressure plateaus compared with the as-cast and as-spun alloys,which correspond to the hydrogen absorption and desorption process of LaMgNi4 and corresponding hydride.Furthermore,the enthalpy and entropy changes of LaMgNi4 during hydrogenation at different temperatures were calculated using Van't Hoff methods.     

Effect of annealing treatment on the anti-pulverization and anti-corrosion properties of La0.67Mg0.33Ni2.5Co0.5 hydrogen storage alloy

The La0.67Mg0.33Ni2.5Co0.5 hydrogen storage alloy was prepared by the vacuum intermediate frequency induction furnace followed by annealing treatment. The pulverization degree of both the as-cast and annealed alloy powders after gaseous hydriding and dehydriding cycle was investigated and the discovery was that annealing treatment could hardly ameliorate their anti-pulverization ability. The element content of La, Mg, Ni and Co existing in electrolyte before and after the electrochemical cycles by using ICP-AES technology was also analyzed and it showed that a large amount of La and Mg were dissolved in the electrolyte, but the amount of dissolution for La and Mg significantly declined when the alloy was annealed. The XRD analysis revealed that all the alloys consisted of two main phases AB3 and AB2 and a residual phase AB5 while annealing treatment made the AB2 phase decrease slightly. Furthermore, the anti-corrosion abilities of various elements in different phases of the as-cast and annealed alloy samples were studied by analyzing the element(La, Mg, Ni, Co) change with the corrosion time in phases AB3 and AB2 by means of EDS. It turned out that the element of La was mainly corroded out from the phase AB2 while not easily from the phase AB3. However, the element of Mg was both easily corroded out from the phases AB2 and AB3, but the corrosion was more obvious in the phase AB3. Therefore, annealing improved the anti-corrosion performances of La and Mg in the phase AB2.     

Structure and high-temperature electrochemical properties of La_（0.60）Nd_（0.15）Mg_（0.25）Ni_（3.3）Si_（0.10） hydrogen storage alloys

The structure and high-temperature electrochemical properties of the as-cast and annealed (940 °C, 8 h) La0.60Nd0.15Mg0.25Ni3.3Si0.10 hydrogen storage alloys were investigated. The X-ray diffraction revealed that the multiphase structure of the as-cast alloy with LaNi5 phase as the main phase was converted into a double-phase structure with La2Ni7 phase as the main phase after annealing. The surface morphology studied by scanning electronic microscope (SEM) showed that the annealed alloy had a much higher anti-corrosion ability than the as-cast alloy. Both alloys presented excellent activation characteristics at all test temperatures. The maximum discharge capacity of the as-cast alloy decreased when the test temperature increased, while the temperature almost had no effect on the annealed alloy. As the test temperature increased, the cyclic stability and charge retention of both alloys decreased, and these properties were improved significantly by annealing.     

Phase structure and electrochemical properties of non-stoichiometric La0.7Ce0.3(Ni3.65Cu0.75Mn0.35Al0.15(Fe0.43B0.57)0.10)x hydrogen storage alloys

Phase structure and electrochemical characteristics of Co-free La0.7Ce0.3(Ni3.65Cu0.75Mn0.35Al0.15(Fe0.43B0.57)0.10)x (0.90≤x≤1.10) al-loys were investigated. When x was 0.90, the alloy was composed of LaNi5, La3Ni13B2 and Ce2Ni7 phases. The Ce2Ni7 phase disappeared, and the abundant of La3Ni13B2 phase decreased when x increased to 0.95. When x was 1.00 or higher the alloys consisted of LaNi5 phase. The lat-tice parameter a and the cell volume V of the LaNi5 phase decreased, and the c/a ratio of the LaNi5 phase increased with x value increasing. Maximum discharge capacity of the alloy electrodes first increased and then decreased with x value increasing from 0.90 to 1.10, and the highest value was obtained when x was 1.00. High-rate dischargeability at the discharge current density of 1200 mA/g increased from 50.7% (x= 0.90) to 64.1% (x=1.10). Both the charge-transfer reaction at the electrode/electrolyte interface and the hydrogen diffusion in the alloy were responsible for the high-rate dischargeability. Cycling capacity retention rate at 100th cycle (S100) gradually increased from 77.3% (x= 0.90) to 84.6% (x=1.10), which resulted from the increase in Ni content and the c/a ratio of the LaNi5 phase with x value increasing.     

Microstructure and electrochemical characteristics of La0.7Ce0.3Ni3.75Mn0.35Al0.15Cu0.75-x（V0.81Fe0.19）x hydrogen storage alloys

Microstructure and electrochemical characteristics of La0.7Ce0.3Ni3.75Mn0.35Al0.15Cu0.75-x(V0.81Fe0.19)x hydrogen storage alloys were investigated. XRD indicated that La0.7Ce0.3Ni3.75Mn0.35Al0.15Cu0.75-x(V0.81Fe0.19)x alloys consisted of a single phase with CaCu5-type structure, and the lattice parameter a and cell volume V increased with increasing x value. The maximum discharge capacity first increased from 319.0 (x=0) to 324.0 mAh/g (x=0.05), and then decreased to 307.0 mAh/g (x=0.20). The high-rate dischargeability at the discharge current density of 1200 mA/g first increased from 52.1% (x=0) to 59.1% (x=0.15), and then decreased to 55.4% (x=0.20). The hydrogen diffusion in the bulky alloy was responsible for the high-rate dischargeability. Cycling stability first increased with increasing x from 0 to 0.10 and then decreased when x increased to 0.20, which was resulted from the synthesized effect of the improvement of the pulverization resistance and the decrease of corrosion resistance.     

Effects of Fe-substitution for cobalt on electrochemical properties of La-Mg-Ni-based alloys

In order to improve electrochemical properties,especially cycling stability,Co was partially substituted by Fe in A2B7-type La-Mg-Ni-based alloys.The La0.74Mg0.26Ni2.55Co0.65-xFex(x=0,0.10,0.20,0.30) alloys were prepared by inductive melting,and their phase structure and electrochemical properties were studied.The XRD and SEM results showed that the alloys consisted mainly of(La,Mg)2Ni7 phase,(La,Mg)5Ni19 phase and LaNi5 phase,except for absence of LaNi5 phase in the non-substituted alloy.The(La,Mg)5Ni19 ph...     

Hydriding and Dehydriding Characteristics of Mechanically Alloyed LaMgl7Ni Composite Material

A composite material with the nominal composition LaMgl7Ni was synthesized by mechanical alloying and thehydriding/dehydriding (H/D) behaviors of this material were studied at several temperatures. This material has a hydrogenstorage capacity (5.76% H2, mass fraction) lower than conventionally alloyed La2Mg17(6.63% H2, mass fraction) without activation but shows a superior hydriding/dehydriding kinetic property. At 523 K it absorbed 4.97% (mass fraction)in less than 1 rain, approximately 100 times faster than La2Mg17 alloy under the same conditions. This attractive kineticproperty of the alloy can be ascribed to the catalytic action of Mg2Ni, LaH2 and La as well as the multiphase structure formed in the preparation processes. The relationships between the equilibrium plateau pressure and the temperature canbe expressed as lgpeq = - 2797/T 4.267 (553 K≤ T≤623 K) for hydriding and lgpeq = - 3957/T 6.063(553 K≤T≤623 K) for dehydriding.     

Effect of neodymium,gadolinium addition on microstructure and mechanical properties of AZ80 magnesium alloy

The microstructure and mechanical properties of AZ80 magnesium alloys with varying Nd, Gd contents were investigated. The results revealed that the as-cast microstructure of AZ80 alloy was composed of α-Mg matrix and divorced eutectic β-Mg_(17)Al_(12) phases. The fraction of Mg_(17)Al_(12) phase was reduced when 0.6 wt.% Nd was added, and new rod-shaped Al_(11)Nd_3 phase and small block-shaped Al-Nd-Mn phase appeared. With Gd addition, the Gd elements mixed with Nd to form rare earth phases. New block-shaped Al_2Gd and Al_2Nd phases which were collectively called Al_2RE phases were observed in the microstructure with more than 0.6 wt.% Gd addition. Moreover, the addition of Gd could promote the precipitation of block-shaped Al_2RE phase, and inhibit the original rod-shaped Al_(11)Nd_3 phase. The AZ80-0.6Nd-0.6Gd alloy exhibited the optimal mechanical properties among all the experimental alloys, in which the tensile strength, yield strength and elongation were 215, 145 MPa and 8.33%, respectively.     

Microstructure and electrochemical properties of melt-spun Nd_(0.8)Mg_(0.2)(Ni_(0.8)Co_(0.2))_(3.8) hydrogen storage alloy

The effects of rapid solidification on the microstructure and electrochemical properties of Nd0.8Mg0.2(Ni0.8Co0.2)3.8 alloy were systematically investigated.The microstructure of alloys was characterized by scanning electron microscopy(SEM),X-ray diffractometer(XRD) and transmission electron microscopy(TEM).It was found that the melt-spun Nd0.8Mg0.2(Ni0.8Co0.2)3.8 ribbons became thinner and the average grain size of the ribbons became smaller with increasing wheel speed.A fraction of amorphous phase was observed for the ribbons melt-spun at high wheel speed(≥20 m/s).Microstructural characterization revealed that two phases:(Nd,Mg)2(Ni,Co)7 main phase(Ce2Ni7 type structure) and NdNi5 second phase(CaCu5 type structure),existed in the samples in cast state and melt-spun.The cycle stability of the melt-spun alloys was significantly enhanced as compared with cast alloy,and the sample prepared at wheel speed of 20 m/s exhibited good comprehensive electrochemical properties.     

Influence of magnesium on electrochemical properties of RE3-xMgx(Ni0.7Co0.2Mn0.1)9（x=0.5-1.25） alloy electrodes

RE3-xMgx(Ni0.7Co0.2Mn0.1)9 (x=0.5-1.25) alloys were prepared by induction melting and the influence of the partial substitution of RE (where RE stands for La-rich mischmetal) by Mg on the hydrogen storage and electrochemical properties of the alloys were investigated systematically. These alloys mainly consisted of three phases, La(Ni,Mn,Co)5 phase, La2Ni7 phase and Mg2Ni phase. The P-C-T isotherms showed that with Mg content increasing in the alloys, the hydrogen storage capacity first increased and reached the maximum capacity of 1.36 wt.% when x=1.0, and then decreased with x increasing further. Electrochemical studies revealed that the discharge capacity reached the maximum value of 380 mAh/g and the alloy electrode presented better cyclic stability when RE/Mg=2. The high rate discharge ability of the alloy electrodes was also improved by the substitution of Mg for RE. The RE2Mg(Ni0.7Co0.2Mn0.1)9 alloy exhibited better hydrogen absorption kinetics (x=1.0).)     

Improved electrochemical kinetic performances of La-Mg-Ni-based hydrogen storage alloys with lanthanum partially substituted by yttrium

Yttrium(Y) has been used as the partial substitution element for lanthanum(La) to improve the electrochemical kinetic performances of La-Mg-Ni-based hydrogen storage alloys. La0.80–xYxMg0.20Ni2.85Mn0.10Co0.55Al0.10(x=0.00, 0.05 and 0.10) alloys were prepared by the inductive melting technique. The alloys were composed of La Ni5 and(La,Mg)2Ni7 phases, the introduction of Y promoted the formation of(La,Mg)2Ni7 phase, and thus the Y-substituted alloy electrodes exhibited higher discharge capacities. Y substitution was also found to be effective to improve the discharge kinetics of the alloy electrodes. When the Y content x increased from 0.00 to 0.10, the high-rate dischargeability of the alloy electrodes at a discharge current density of 1800 m A/g(HRD1800) increased from 23.6% to 39.7% at room temperature. In addition, the measured HRD1800 showed a linear dependence on both the exchange current density and the hydrogen diffusion coefficient at different temperatures, respectively.