GaN的MOVPE生长和m－i－n型蓝光LED的试制

利用自行研制的常压ＭＯＶＰＥ设备和全部国产ＭＯ源，采用低温生长缓冲层技术，在蓝宝石（α－Ａｌ２Ｏ３）衬底上获得了高质量的ＧａＮ外延层。未掺杂的ＧａＮ外延层的室温电子迁移率已达１１４ｃｍ２／Ｖ．ｓ，载流于浓度为２×１０１８。７７Ｋ光致发光谱近带边发射峰波长为３６５ｎｍ，其线宽为４ＤｍｅＶ。Ｘ射线双晶衍射回摆曲线的线宽为３６０ａｒｃｓｅｃ。用Ｚｎ掺杂生长了绝缘的ｉ－ＧａＮ层。在此基础上研制了ｍ－ｉ－ｎ型ＧａＮ的ＬＥＤ，并在室温正向偏压下发出波长为４５５ｎｍ的蓝光。     

GaAs－InP复合材料的外延生长方法及金属半导体场效应晶体管器件制备

提出了一种新的生长过渡层的方法，并利用低压金属有机气相外延技术在ＩｎＰ衬底上生长出高质量ＧａＡｓ外延材料，用Ｘ射线双晶衍射测得５μｍ厚ＧａＡｓ外延层的（００４）晶面衍射半峰高宽（ＦＷＨＭ）低至１４０ａｒｃｓｅｃ。并制出ＧａＡｓ金属半导体场效应晶体管（ＭＥＳＦＥＴ），其单位跨导为１００ｍｓ／ｍｍ，可满足与长波长光学器件进行单片集成的需要。     

GaAs—InP复合材料的外延生长方法及金属半导体场效应晶体管器件制备

提出了一种新的生长过渡层的方法，并利用低压金属有机气相外延技术在ＩｎＰ初底上生长出高质量ＧａＡｓ外延材料，用Ｘ射线双晶衍射测得５μｍ厚ＧａＡｓ外延层的晶面衍射半峰高宽（ＦＷＨＭ）低至１４０ａｒｃ ｓｅｃ。并制出ＧａＡｓ金属半导体场效应晶体管（ＭＥＳＦＥＴ），其单位跨导为１００ｍｇ／ｍｍ，可满足与长波长光这器件进行单片集成的需要。     

分子束外延生长室内晶片生长过程中真空度的测量

分子束外延生长室内晶片生长过程中真空度的测量张伯文（复旦大学）ＶａｃｕｕｍＭｅａｓｕｒｅｍｅｎｔｄｕｒｉｎｇｔｈｅＰｒｏｃｅｓｓｏｆＣｒｙｓｔａｌＣｈｉｐＧｒｏｗｔｈｉｎｔｈｅＧｒｏｗｔｈＣｈａｍｂｅｒｏｆＭｏｌｅｃｕｌａｒＢｅａｍＥｐｉｔａｘｙ￥Ｚ...     

GaN材料的GSMBE生长

在国内首次用ＮＨ３作氮源的ＧＳＭＢＥ方法在α－Ａｌ２Ｏ３衬底上生长出了ＧａＮ单昌外延膜。ＧａＮ生长速率可达０．５μｍ／ｈ。ＧａＮ外延膜的（０００２）双晶Ｘ射线衍射峰回摆曲线的半高宽最窄为８ａｒｃｍｉｎ。霍尔迁移率为５０ｃｍ＾２／Ｖ．ｓ。对质量好的ＧａＮ膜，室温阴性发光谱上只有一个强而锐的近岸边发光峰，谱峰位于３７２ｎｍ处，谱峰半高宽为１４ｎｍ（１２５ｍｅＶ）。     

p~＋－GaInAsSb／p－GaInAsSb／n－GaSb异质结红外控测器

ＧａＩｎＡｓＳｂ是红外探测器中重要的半导体材料之一。我们用水平常压金属氧化物化学气相淀积（ＭＯＣＶＤ）技术在ｎ型ＧａＳｂ衬底上成功地生长了ＧａＩｎＡｓＳｂ外延层，用ＰＬ谱、红外吸收谱、Ｘ射线衍射和扫描电子超声显微镜（ＳｃａｎｎｉｎｇＥｌｅｃｔｒｏｎＡｃｏｕｓｔｉｃＭｉｃｒｏｓｃｏｐｙ，ＳＥＡＭ）等实验手段对ＧａＩｎＡｓＳｂ外延层进行了表征。用ＧａＩｎＡｓＳｂ材料制作的红外探测器的光谱响应的截止波长达２．４μｍ，室温探测率Ｄ＊达１×１０９ｃｍＨｚ（１／２）／Ｗ，２．２５μｍ波长时的量子效率为３０％。本文首次给出了ＧａＩｎＡｓＳｂ外延层的扫描电子超声显微镜像（ＳＥＡＭ像），为扫描电子超声显微镜在半导体材料方面的应用开辟了一个新的领域。     

NH3-MBE生长极化场二维电子气材料

介绍了用ＮＨ３－ＭＢＥ技术在蓝宝石Ｃ面上外延的高质量的ＧａＮ单层膜以及ＧＮ／ＡｌＮ／ＧａＮ极化感应二维电子气材料。外延膜都是Ｎ面材料。形成的二维电子气是“倒置二维电子气”。ＧａＮ单层膜的室温电子迁移率为３００ｃｍ＾２／Ｖｓ。二维电子气材料的迁移率为６８０ｃｍ＾２／Ｖｓ（ＲＴ）和１７００ｃｍ＾２／Ｖｓ（７７Ｋ）,相应的二维电子气的面密度为３．２＊１０＾１３ｃｍ＾－２（ＲＴ）和２．６ｘ１０＾１３ｃｍ＾     

高迁移率AlGaN-GaN二维电子气

用金属有机物气相外延方法在（０００１）蓝宝石衬底上生长了ＡｌｘＧａ１－ｘＮ／ＧａＮ二维电子气结构。Ａｌ０．１３Ｇａ０．８７Ｎ（７００ｎｍ）／ＧａＮ（６００ｎｍ）异质结的室温电子迁移率达１０２４ｃｍ＾２／Ｖｓ,而ＧａＮ体材料的室温电子迁移率为３９０ｃｍ＾２／Ｖｓ;该异质结的７７Ｋ电子迁移率达３５００ｃｍ＾２／Ｖｓ,而ＧａＮ体材料的电子迁移率在１８５Ｋ下达到峰值,为４９０ｃｍ＾２／Ｖｓ,７７Ｋ下下降到     

SI—GaAs中的EL2和EL6缺陷团簇相关性研究

用光致电流瞬态谱（ＰＩＴＳ）方法研究了ＬＥＣＳＩ－ＧａＡｓ原生单晶经常规退火和等时快速退火（ＲＴＡ）深能级缺陷的变化。缺陷ＥＬ２（Ｅｃ－０．８２ｅＶ）ＥＬ１２（Ｅｃ－０．７９ｅＶ）表现出类似的ＲＴＡ特性，应属于ＥＬ２缺陷团簇；缺陷ＥＬ６（Ｅｃ－０．３８ｅＶ），ＥＬ８（Ｅｃ－０．２７ｅＶ）和ＥＬ９（Ｅｃ－０．２４ｅＶ０亦具有相似的ＲＴＡ特性，属ＥＬ６缺陷团簇。实验发现，在热退火中，ＥＬ２团簇缺陷密度     

SI－GaAs中EL2和EL6缺陷团簇相关性研究

用光致电流瞬态谱（ＰＩＴＳ）方法研究了ＬＥＣＳＩ－ＧａＡｓ原生单晶经常规退火和等时快速退火（ＲＴＡ）深能级缺陷的变化。缺陷ＥＬ２（Ｅｃ－０．８２ｅＶ）和ＥＬ１２（Ｅｃ－０．７９ｅＶ）表现出类似的ＲＴＡ特性，应属于ＥＬ２缺陷团簇；缺陷ＥＬ６（Ｅｃ－０．３８ｅＶ），ＥＬ８（Ｅｃ－０．２７ｅＶ）和ＥＬ９（Ｅｃ－０．２４ｅＶ）亦具有相似的ＲＴＡ特性，属ＥＬ６缺陷团簇。实验发现，在热退火中，ＥＬ２团簇缺陷密度减少，则ＥＬ６团簇缺陷密度增加；反之亦然，取决于退火温度的高低，表明ＥＬ２，ＥＬ６团簇在原子结构上相关。文中由此讨论了两个主要缺陷ＥＬ２和ＥＬ６的可能构型。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from