Efficient synthesis of titania nanotubes and enhanced photoresponse of Pt decorated TiO2 for water splitting

We investigated the effect of HMT (hexamethylenetetraamine) on the anodic growth of TiO₂ nanotube arrays. The tube length increases to 4.3 μm with HMT concentration increasing to 0.04 mol·L⁻¹. Adsorption of HMT on the TiO₂ surface is shown to markedly decrease the chemical dissolution rate of tube mouth, resulting in longer nanotube length. Furthermore, Pt nanoparticles were successfully deposited on the surface of TiO₂ nanotubes by ac electrodeposition method. The TiO₂/Pt composites were characterized by field emission scanning electron microscope (FESEM), X-ray photoelectron spectra (XPS), and photoelectrochemistry. An enhancement in photocurrent density has been achieved upon modification of TiO₂ nanotubes with Pt nanoparticles.     

Effect of TiO2 nanotubes with TiCl4 treatment on the photoelectrode of dye-sensitized solar cells

In this study, we used the electrochemical anodization to prepare TiO₂ nanotube arrays and applied them on the photoelectrode of dye-sensitized solar cells. In the field emission scanning electron microscopy analysis, the lengths of TiO₂ nanotube arrays prepared by electrochemical anodization can be obtained with approximately 10 to 30 μm. After titanium tetrachloride (TiCl₄) treatment, the walls of TiO₂ nanotubes were coated with TiO₂ nanoparticles. XRD patterns showed that the oxygen-annealed TiO₂ nanotubes have a better anatase phase. The conversion efficiency with different lengths of TiO₂ nanotube photoelectrodes is 3.21%, 4.35%, and 4.34% with 10, 20, and 30 μm, respectively. After TiCl₄ treatment, the efficiency of TiO₂ nanotube photoelectrode for dye-sensitized solar cell can be improved up to 6.58%. In the analysis of electrochemical impedance spectroscopy, the value of R_k (charge transfer resistance related to recombination of electrons) decreases from 26.1 to 17.4 Ω when TiO₂ nanotubes were treated with TiCl₄. These results indicate that TiO₂ nanotubes treated with TiCl₄ can increase the surface area of TiO₂ nanotubes, resulting in the increase of dye adsorption and have great help for the increase of the conversion efficiency of DSSCs.     

Fabrication of high aspect ratio and open‐ended TiO2 nanotube photocatalytic arrays through electrochemical anodization

Well‐aligned, high aspect‐ratio and open‐ended TiO₂ nanotube arrays secured within a Ti foil (TiO₂ nanotubes cartridge) were successfully prepared through the double‐sided anodization method. With ～210 µm of nanotube length, the anodic growth of TiO₂ was accelerated and stabilized by the lactic acid‐containing ethylene glycol electrolyte. In the absence of lactic acid, the anodization led to detachment of nanotubes from the Ti foil after 5–6 h of high voltage (80 V) anodization. Transmission electron microscope image and Raman spectrum revealed that the as‐anodized TiO₂ nanotube arrays without annealing treatment were partially crystalline anatase and demonstrated photocatalytic activity in the mineralization of formic acid. © 2015 American Institute of Chemical Engineers AIChE J, 62: 415–420, 2016     

Capability of coupled CdSe/TiO2 heterogeneous structure for photocatalytic degradation and photoconductivity

Highly ordered TiO₂ nanotube arrays (TiO₂-NTAs), with a uniform tube size on titanium substrate, were obtained by means of reoxidation and annealing. A composite structure, CdSe quantum dots@TiO₂ nanotube arrays (CdSe QDs@TiO₂-NTAs), was fabricated by assembling CdSe quantum dots into TiO₂-NTAs via cyclic voltammetry electrochemical deposition. The X-ray diffractometer (XRD), field-emission scanning electron microscope (SEM), and transmission electron microscope (TEM) were carried out for the determination of the composition and structure of the tubular layers. Optical properties were investigated by ultraviolet-visible spectrophotometer (UV-Vis). Photocurrent response under visible light illumination and photocatalytic activity of samples by degradation of methyl orange were measured. The results demonstrated that the photo absorption of the composite film shifted to the visible region, and the photocurrent intensity was greatly enhanced due to the assembly of CdSe QDs. Especially, photocurrent achieved a maximum of 1.853 μA/cm² after five voltammetry cycles of all samples. After irradiation under ultra violet-visible light for 2 h, the degradation rate of composition to methyl orange (MO) reached 88.20%, demonstrating that the CdSe QDs@TiO₂-NTAs exhibited higher photocatalytic activity.     

The effect of dye-sensitized solar cell based on the composite layer by anodic TiO2 nanotubes

TiO₂ nanotube arrays are very attractive for dye-sensitized solar cells (DSSCs) owing to their superior charge percolation and slower charge recombination. Highly ordered, vertically aligned TiO₂ nanotube arrays have been fabricated by a three-step anodization process. Although the use of a one-dimensional structure provides an enhanced photoelectrical performance, the smaller surface area reduces the adsorption of dye on the TiO₂ surface. To overcome this problem, we investigated the effect of DSSCs constructed with a multilayer photoelectrode made of TiO₂ nanoparticles and TiO₂ nanotube arrays. We fabricated the novel multilayer photoelectrode via a layer-by-layer assembly process and thoroughly investigated the effect of various structures on the sample efficiency. The DSSC with a four-layer photoelectrode exhibited a maximum conversion efficiency of 7.22% because of effective electron transport and enhanced adsorption of dye on the TiO₂ surface.     

Immobilization of pamidronic acids on the nanotube surface of titanium discs and their interaction with bone cells

Self-assembled layers of vertically aligned titanium nanotubes were fabricated on a Ti disc by anodization. Pamidronic acids (PDAs) were then immobilized on the nanotube surface to improve osseointegration. Wide-angle X-ray diffraction, X-ray photoelectron microscopy, and scanning electron microscopy were employed to characterize the structure and morphology of the PDA-immobilized TiO₂ nanotubes. The in vitro behavior of osteoblast and osteoclast cells cultured on an unmodified and surface-modified Ti disc was examined in terms of cell adhesion, proliferation, and differentiation. Osteoblast adhesion, proliferation, and differentiation were improved substantially by the topography of the TiO₂ nanotubes, producing an interlocked cell structure. PDA immobilized on the TiO₂ nanotube surface suppressed the viability of the osteoclasts and reduced their bone resorption activity.     

Effect of synthesis highly ordered TiO<Subscript>2</Subscript> nanotube arrays with enhanced photocatalytic properties by time,electrolytic voltage,heating temperature and Polyvinyl pyrrolidone

Highly ordered TiO₂ nanotube arrays were prepared by anodization method with doped Polyvinyl pyrrolidone (PVP) addition. The as-prepared samples were characterized by scanning electron microscope (SEM), X-ray diffraction (XRD) and transmission electron microscopy. The results suggested that TiO₂ nanotubes arrays modified by 0.10 wt% PVP were better uniform and more highly ordered than that of pure TiO₂. The average inner diameter and the tube length of TiO₂ nanotubes were extended approximately 77 nm and 5.21 μm, respectively. Meanwhile, the optimum synthesis conditions (40 V, 4 h and 450 °C) were determined by SEM and XRD. In addition, the photocatalytic activity of the as-prepared samples was investigated for the degradation of RhB under UV-lamp irradiation. The results showed that almost 100 % of RhB was degradation within 80 min by the as-prepared nanotubes in the optimum synthesis conditions. It was indicated that the photocatalytic activity of the as-prepared nanotubes was improved greatly due to their well morphology, enhanced UV-light absorption property and electron transmission ability. In general, this study could provide a principle method to synthesize TiO₂ nanotube arrays with enhanced photocatalytic activity and improved microstructure by anodization process with PVP addition.     

TiO2 micro-flowers composed of nanotubes and their application to dye-sensitized solar cells

TiO₂ micro-flowers were made to bloom on Ti foil by the anodic oxidation of Ti-protruding dots with a cylindrical shape. Arrays of the Ti-protruding dots were prepared by photolithography, which consisted of coating the photoresists, attaching a patterned mask, illuminating with UV light, etching the Ti surface by reactive ion etching (RIE), and stripping the photoresist on the Ti foil. The procedure for the blooming of the TiO₂ micro-flowers was analyzed by field emission scanning electron microscopy (FESEM) as the anodizing time was increased. Photoelectrodes of dye-sensitized solar cells (DSCs) were fabricated using TiO₂ micro-flowers. Bare TiO₂ nanotube arrays were used for reference samples. The short-circuit current (J_sc) and the power conversion efficiency of the DSCs based on the TiO₂ micro-flowers were 4.340 mA/cm² and 1.517%, respectively. These values of DSCs based on TiO₂ micro-flowers were higher than those of bare samples. The TiO₂ micro-flowers had a larger surface area for dye adsorption compared to bare TiO₂ nanotube arrays, resulting in improved J_sc characteristics. The structure of the TiO₂ micro-flowers allowed it to adsorb dyes very effectively, also demonstrating the potential to achieve higher power conversion efficiency levels for DSCs compared to a bare TiO₂ nanotube array structure and the conventional TiO₂ nanoparticle structure.     

Growth and characterization of TiO2 nanotubes from sputtered Ti film on Si substrate

In this paper, we present the synthesis of self-organized TiO₂ nanotube arrays formed by anodization of thin Ti film deposited on Si wafers by direct current (D.C.) sputtering. Organic electrolyte was used to demonstrate the growth of stable nanotubes at room temperature with voltages varying from 10 to 60 V (D.C.). The tubes were about 1.4 times longer than the thickness of the sputtered Ti film, showing little undesired dissolution of the metal in the electrolyte during anodization. By varying the thickness of the deposited Ti film, the length of the nanotubes could be controlled precisely irrespective of longer anodization time and/or anodization voltage. Scanning electron microscopy, atomic force microscopy, diffuse-reflectance UV–vis spectroscopy, and X-ray diffraction were used to characterize the thin film nanotubes. The tubes exhibited good adhesion to the wafer and did not peel off after annealing in air at 350 °C to form anatase TiO₂. With TiO₂ nanotubes on planar/stable Si substrates, one can envision their integration with the current micro-fabrication technique large-scale fabrication of TiO₂ nanotube-based devices.     

Fabrication of dye-sensitized solar cells using ordered and vertically oriented TiO2 nanotube arrays with open and closed ends

Highly ordered and vertically oriented TiO₂ nanotube arrays were prepared and applied to dye sensitized solar cell (DSSC) as working electrodes. The nanotube arrays were fabricated using atomic layer deposition and AAO template. The two types of nanotube's end, closed-end and open-end, were produced by reactive ion etching (RIE) process. The structure of nanotube arrays was characterized by FE-SEM, TEM, and XRD. DSSCs using the TiO₂ nanotube arrays as working electrodes were fabricated and characterized. The DSSCs prepared from the TiO₂ nanotubes with open end exhibited higher power conversion efficiency of 1.17% than that with closed end. This result is attributed to that the open-ended TiO₂ nanotubes provided larger surface area, leading to more amount of dye molecules to adsorb followed by the higher light absorption.     

Photoelectrocatalytic properties of Ag nanoparticles loaded TiO2 nanotube arrays prepared by pulse current deposition

A pulse current deposition technique was adopted to construct highly dispersed Ag nanoparticles on TiO₂ nanotube arrays which were prepared by the electrochemical anodization. The morphology, crystallinity, elemental composition, and UV-vis absorption of Ag/TiO₂ nanotube arrays were characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and diffuse reflectance spectra (DRS). In particular, the photoelectrochemical properties and photoelectrocatalytic activity under UV light irradiation and the photocatalytic activity under visible light irradiation for newly synthesized Ag/TiO₂ nanotube arrays were investigated. The maximum incident photon to charge carrier efficiency (IPCE) value of Ag/TiO₂ nanotube arrays was 51%, much higher than that of pure TiO₂ nanotube arrays. Ag/TiO₂ nanotube arrays exhibited higher photocatalytic activities than the pure TiO₂ nanotube arrays under both UV and visible light irradiation. The photoelectrocatalytic activity of Ag/TiO₂ nanotube arrays under UV light irradiation was 1.6-fold enhancement compared with pure TiO₂ nanotube arrays. This approach can be used in synthesizing various metal-loaded nanotube arrays materials.     

Diameter-sensitive biocompatibility of anodic TiO2 nanotubes treated with supercritical CO2 fluid

This work reports on the diameter-sensitive biocompatibility of anodic TiO₂ nanotubes with different nanotube diameters grown by a self-ordering process and subsequently treated with supercritical CO₂ (ScCO₂) fluid. We find that highly hydrophilic as-grown TiO₂ nanotubes become hydrophobic after the ScCO₂ treatment but can effectively recover their surface wettability under UV light irradiation as a result of photo-oxidation of C-H functional groups formed on the nanotube surface. It is demonstrated that human fibroblast cells show more obvious diameter-specific behavior on the ScCO₂-treated TiO₂ nanotubes than on the as-grown ones in the range of diameters of 15 to 100 nm. This result can be attributed to the removal of disordered Ti(OH)₄ precipitates from the nanotube surface by the ScCO₂ fluid, thus resulting in purer nanotube topography and stronger diameter dependence of cell activity. Furthermore, for the smallest diameter of 15 nm, ScCO₂-treated TiO₂ nanotubes reveal higher biocompatibility than the as-grown sample.     

Preparation and magnetic properties of iron titanium oxide nanotube arrays

FeTi alloy was prepared by a vacuum smelting method, iron titanium oxide nanotube arrays have been made directly by anodization of the FeTi alloy. Morphologies and microstructures of the samples were characterized by scanning electron microscope, transmission electron microscope, and X-ray diffractometer. Influences of temperature and H₂O concentration on the morphologies of the nanotube arrays have been discussed in detail. Magnetic properties of the samples have also been investigated. The as-prepared samples were amorphous. When annealed at 500 °C and 550 °C, pesudobrookite Fe₂TiO₅ was obtained. At 600 °C, there were mixed Fe₂TiO₅, rutile TiO₂, and α-Fe₂O₃. Magnetic performance of the nanotube arrays exhibited high sensitivity to temperature and changed interestingly upon annealing. The values of the coercivity and remanence were 340 Oe and 0.061 emu/g respectively for the sample annealed at 550 °C.     

Photoelectrochemical oxidation of salicylic acid and salicylaldehyde on titanium dioxide nanotube arrays

We report on the kinetics of photoelectrochemical oxidation of salicylic acid (SA) and salicylaldehyde (SH) on titanium dioxide nanotube arrays. The TiO₂ nanotubes were prepared by the electrochemical oxidation of titanium substrates in a nonaqueous electrolyte (DMSO/HF). Scanning electron microscopy (SEM) was employed to examine the morphology of the formed nanotubes. Linear voltammetry was used to study the electrochemical and photoelectrochemical behavior of the synthesized TiO₂ nanotube arrays. The photoelectrochemical oxidation of SA and SH on the TiO₂ nanotubes was monitored by in situ UV-vis spectroscopy, showing that the kinetics of the photoelectrochemical oxidation of SA and SH follows pseudo first-order and that the rate constant of SH oxidation is 1.5 times larger than that of SA degradation. Quantum chemical calculations based on the DFT method were performed on SA and SH to address the large difference in kinetics. The relatively higher E_LUMO − E_HOMO makes SA more stable and thus more difficult to be oxidized photoelectrochemically. The impact of temperature and initial concentrations on the kinetics of SA and SH photoelectrochemical degradation was also investigated in the present work.     

Ni-doped TiO2 nanotubes for wide-range hydrogen sensing

Doping of titania nanotubes is one of the efficient way to obtain improved physical and chemical properties. Through electrochemical anodization and annealing treatment, Ni-doped TiO₂ nanotube arrays were fabricated and their hydrogen sensing performance was investigated. The nanotube sensor demonstrated a good sensitivity for wide-range detection of both dilute and high-concentration hydrogen atmospheres ranging from 50 ppm to 2% H₂. A temperature-dependent sensing from 25°C to 200°C was also found. Based on the experimental measurements and first-principles calculations, the electronic structure and hydrogen sensing properties of the Ni-doped TiO₂ with an anatase structure were also investigated. It reveals that Ni substitution of the Ti sites could induce significant inversion of the conductivity type and effective reduction of the bandgap of anatase oxide. The calculations also reveal that the resistance change for Ni-doped anatase TiO₂ with/without hydrogen absorption was closely related to the bandgap especially the Ni-induced impurity level.     

Hierarchical structured TiO2 nano-tubes for formaldehyde sensing

Hierarchical structured TiO₂ nano-tubes were prepared following a two-step method: the highly ordered uniform TiO₂ nanotube arrays were first grown by the conventional electrochemical anodization of the Ti metal sheet followed by mechanical milling of the as-fabricated TiO₂ nanotube arrays. The obtained nanotubes with a length around 400 nm and opening diameter ∼100 nm were formed mixed with the spherical TiO₂ single crystals with a diameter around 10 nm indicating hierarchical nanostructure. The as-synthesized TiO₂ hierarchical nanotubes based resistive-type chemical sensor exhibits good sensitivity to formaldehyde at room temperatures with or without UV-irradiation. The response of the sensor increased almost linearly as a function of the concentration of formaldehyde from 10–50 ppm under UV irradiation. The response of the sensor to different relative humidity and other possible interferents such as ammonia, methanol and alcohol was investigated. The larger response of the sensor to formaldehyde relative to these interferents is suggested to be due to the deeper diffusion of formaldehyde into the TiO₂ nanotubes.     

Preparation and photocatalytic properties of RuO2/TiO2 composite nanotube arrays

RuO₂/TiO₂ composite nanotube arrays were prepared using an anodic oxidation method combined with dipping. The photocatalytic properties of RuO₂/TiO₂ nanotube arrays in methylene blue solution were investigated under visible light irradiation. The results showed that Ru existing in the form of RuO₂ was dispersed uniformly on the surface of TiO₂ nanotubes, and the RuO₂ did not change the crystal structure of TiO₂ nanotubes. The load of RuO₂ on TiO₂ had a little influence on the band-gap energy and the absorption band edge, but could increase the amount of Ti-OH functional groups on the surface of TiO₂ nanotubes. The RuO₂/TiO₂ nanotube arrays with the optimal photocatalytic activity were formed in the ruthenium chloride solution with a concentration of 0.0030 mol/L. The 2 h photocatalytic degradation rate of methylene blue increased from 38% for pure TiO₂ nanotubes to 69% for RuO₂/TiO₂ nanotube arrays. This work demonstrated that RuO₂/TiO₂ nanotube arrays showed an improved photocatalytic property over pure TiO₂ nanotubes due to the fact that RuO₂ could capture the photo-generated holes, which greatly decreased the recombination of the photo-generated electrons and holes, and hence lengthen the lifetime of photo-induced electrons and increased the amount of hydroxyl groups absorbed on the TiO₂ nanotubes surface.     

3-D solar cells by electrochemical-deposited Se layer as extremely-thin absorber and hole conducting layer on nanocrystalline TiO2 electrode

Ag₂S quantum dots were deposited on the surface of TiO₂ nanorod arrays by a two-step photodeposition. The prepared TiO₂ nanorod arrays as well as the Ag₂S deposited electrodes were characterized by X-ray diffraction, scanning electron microscope, and transmission electron microscope, suggesting a large coverage of Ag₂S quantum dots on the ordered TiO₂ nanorod arrays. UV–vis absorption spectra of Ag₂S deposited electrodes show a broad absorption range of the visible light. The quantum dot-sensitized solar cells (QDSSCs) based on these electrodes were fabricated, and the photoelectrochemical properties were examined. A high photocurrent density of 10.25 mA/cm² with a conversion efficiency of 0.98% at AM 1.5 solar light of 100 mW/cm² was obtained with an optimal photodeposition time. The performance of the QDSSC at different incident light intensities was also investigated. The results display a better performance at a lower incident light level with a conversion efficiency of 1.25% at 47 mW/cm².     

Synthesis and electrochemical properties of CeO2 nanoparticle modified TiO2 nanotube arrays

In this paper, a cerium dioxide (CeO₂) modified titanium dioxide (TiO₂) nanotube array film was fabricated by electrodeposition of CeO₂ nanoparticles onto an anodized TiO₂ nanotube array. The structural investigation by X-ray diffraction, scanning electron microscopy and transmission electron microscopy indicated that the CeO₂ nanoparticles grew uniformly on the walls of the TiO₂ nanotubes. The composite was composed of cubic-phase CeO₂ crystallites and anatase-phase TiO₂ after annealing at 450 °C. The cyclic voltammetry and chronoamperometric charge/discharge measurement results indicated that the CeO₂ modification obviously increased the charge storage capacity of the TiO₂ nanotubes. The charge transfer process at the surface, that is, the pseudocapacitance, was the dominate mechanism of the charge storage in CeO₂-modified TiO₂ nanotubes. The greater number of surface active sites resulting from uniform application of the CeO₂ nanoparticles to the well-aligned TiO₂ nanotubes contributed to the enhancement of the charge storage density.     

N-doped anodic titania nanotube arrays for hydrogen production

Titanium dioxide (TiO₂) nanotube arrays are grown in a mixed electrolyte by anodizing process. The anodic nanotubes for N-doping were calcinated at 773 K in a tube furnace with a mixture of NH₃ and Ar gas. The photocatalytic activity of N-doped TiO₂ nanotubes was carried out in a water-splitting reaction under UV and visible light irradiation. Various characterization techniques (Scanning electron microscopy, X-ray diffractometry, X-ray photo-electron spectroscopy, etc.) are used to study the surface morphology, phase of structure, and binding energy.