Formation and Transformation of Cubic ZrO2 Solid Solutions in the System ZrO2—Al2O3

In the system ZrO₂-Al₂O₃, cubic ZrO₂ solid solutions containing up to 40 mol% Al₂O₃ crystallize at low temperatures from amorphous materials prepared by the simultaneous hydrolysis of zirconium and aluminum alkoxides. The values of the lattice parameter, a, increase linearly from 0.5095 to 0.5129 nm with increasing Al₂O₃ content. At higher temperatures, the solid solutions transform into tetragonal ZrO₂ and α-Al₂O₃. Pure ZrO₂ crystallizes in the tetragonal form at 415° to 440°C.     

Effect of Particle Size on the Reaction Wave Propagation in the Combustion Synthesis of Al2O3-ZrO2-Nb Composites

The effect of reactant particle size on the kinetics of wave propagation in the thermite system Nb₂O₅+ Al₂Zr + nuAl₂O₃ (with alumina being a diluent) was investigated. Reactants in three size ranges were utilized: fine (1–3 µm), medium (<10 µm), and coarse (10–45 µm). Particle size had an effect on the mode and velocity of the self-propagating combustion wave. For fine particles, the combustion wave propagated in a steady-state mode for all values of dilutions investigated (0 ≤ nu ≤ 0.8). For medium particles with nu > 0.1 and for all coarse particles, wave propagation was in the spin mode. A significantly large difference between the calculated adiabatic combustion temperatures and the measured values was observed and is attributed to large heat losses arising from very wide reaction zones. For fine particles, the temperature dependence of the wave velocity showed a discontinuity at a temperature corresponding to the formation of the eutectic in the binary ZrO₂-Al₂O₃. The velocity can be more than a factor of 3 higher at the same temperature, depending on the amount of the eutectic liquid. The dependence of the wave velocity on particle size ( r ) was found to have the form v is proportional to 1/ r^m with 0.5 < m < 0.8. The upper limit approximates that of m = 1.0 for diffusion-controlled reaction kinetics, according to reported modeling studies. In all cases, regardless of the mode of wave propagation the reactions resulted in the desired products, Nb + ZrO₂+ Al₂O₃ with a microstructure exhibiting the eutectic of the binary ZrO₂-Al₂O₃.     

Crystallization of MgO-Al2O3-SiO2-ZrO2 Glasses

The crystallization of MgO-Al₂O₃-SiO₂-ZrO₂ glasses at 1000°C was studied. Isothermal heat treatments of a cordierite-based glass (2MgO.2Al₂O₃.5SiO₂= Mg₂Al₄Si₅O₁₈) with 7 wt% ZrO₂ produced surface crystallization of α-cordierite and tetragonal ZrO₂ ( t -ZrO₂). These phases advanced into the glass by cocrystallization of t -ZrO₂ rods in an α-cordierite matrix with a well-defined orientation relation. The t -ZrO₂ rods were unstable with respect to diffusional breakup (a Rayleigh instability) and decomposed into rows of aligned ellipsoidal and spheroidal particles. The t -ZrO₂ was very resistant to transformation to monoclinic symmetry. With a similar glass containing 15 wt% ZrO₂, surface crystallization of α-cordierite and t -ZrO₂ was accompanied by internal crystallization of t -ZrO₂ dendrites. Transformation of the dendrites to mono-clinic symmetry was observed under some conditions.     

Grain-Size Distribution in Al2O3─ZrO2 Generated by High-Temperature Annealing

Grain-size distribution in various Al₂O₃─ZrO₂ (2.5 mol% Y₂O₃) ceramics during high-temperature annealing was examined. In alumina-rich alloys, the grain size of major and minor phases was very different, while grain size was almost uniform in zirconia-rich alloys. This difference in grainsize distribution was related to the difference in grain growth rate of the major phase and to the effectiveness of grain-boundary pinning by minor-phase grains.     

Influence of the Y2O3 Content and Temperature on the Mechanical Properties of Melt-Grown Al2O3–ZrO2 Eutectics

The effect of Y₂O₃ content on the flexure strength of melt-grown Al₂O₃–ZrO₂ eutectics was studied in a temperature range of 25°–1427°C. The processing conditions were carefully controlled to obtain a constant microstructure independent of Y₂O₃ content. The rod microstructure was made up of alternating bands of fine and coarse dispersions of irregular ZrO₂ platelets oriented along the growth axis and embedded in the continuous Al₂O₃ matrix. The highest flexure strength at ambient temperature was found in the material with 3 mol% Y₂O₃ in relation to ZrO₂(Y₂O₃). Higher Y₂O₃ content did not substantially modify the mechanical response; however, materials with 0.5 mol% presented a significant degradation in the flexure strength because of the presence of large defects. They were nucleated at the Al₂O₃–ZrO₂ interface during the martensitic transformation of ZrO₂ on cooling and propagated into the Al₂O₃ matrix driven by the tensile residual stresses generated by the transformation. The material with 3 mol% Y₂O₃ retained 80% of the flexure strength at 1427°C, whereas the mechanical properties of the eutectic with 0.5 mol% Y₂O₃ dropped rapidly with temperature as a result of extensive microcracking.     

Rapid Crystallization of SiO2-Al2O3 Glasses

The crystallization of Al₂O₃-rich glasses in the system SiO₂-Al₂O₃ which were prepared by flame-spraying and/or splat-cooling was studied by DTA, electron microscopy, and X-ray diffraction. Over a wide range of compositions, the crystallization temperature ( T_x ) remained near 1000°C, changing smoothly with composition. In all cases crystallization of mullite was detected by X-ray diffraction. In the low-Al₂O₃ region, coarsening of the microstructure during crystallization was observed by electron microscopy. In the high-Al₂O₃ region mullite and γ-Al₂O₃ cocrystallized; this behavior may be interpreted as evidence of a cooperative process of crystallization at the respective T_x 's. The crystallite size of the mullite immediately after rapid crystallization increased continuously with increasing Al₂O₃ content. In light of the T_x data, the adequacy of the evidence for the proposed metastable miscibility gap in the SiO₂-Al₂O₃ system is questioned.     

Homogeneous Fabrication of Al2O3–ZrO2–SiC Whisker Composite by Surface-Induced Coating

Al₂O₃–ZrO₂–SiC whisker composites were prepared by surface-induced coating of the precursor for the ZrO₂ phase on the kinetically stable colloid particles of Al₂O₃ and SiC whisker. The fabricated composites were characterized by a uniform spatial distribution of ZrO₂ and SiC whisker phases throughout the Al₂O₃ matrix. The fracture toughness values of the Al₂O₃–15 vol% ZrO₂–20 vol% SiC whisker composites (∼12 MPa.m^1/2) are substantially greater than those of comparable Al₂O₃–SiC whisker composites, indicating that both the toughening resulting from the process zone mechanism and that caused by the reinforced SiC whiskers work simultaneously in hot-pressed composites.     

Major Influences on the Particle-Size–Transformation-Temperature Relation in Al2O3–ZrO2 Composites

The energetics of martensitic transformation in ZrO₂ is studied using a thermodynamic approach, with particular reference to Al₂O₃–ZrO₂ composites. The different characters of three types of transformation-toughened ceramics are analyzed, and several factors affecting the t → m transformation in Al₂O₃–ZrO₂ composites are discussed. The expression of transformation temperature dependence on particle size is derived and has good agreement with experimental results. The energetics concerned with nucleation of martensitic transformation is also discussed.     

Phase Equilibria in the Pseudoternary System ZrO2−Y2O3−Cr2O3 at 1600°C in Air

The pseudoternary system ZrO₂-Y₂O₃-Cr₂O₃ was studied at 1600°C in air by the quenching method. Only one intermediate compound, YCrO₃, was observed on the Y₂O₃−Cr₂O₃ join. ZrO₂ and Y₂O₃ formed solid solutions with solubility limits of 47 and 38 mol%, respectively. The apex of the compatibility triangle for the cubic ZrO₂, Cr₂O₃, and YCrO₃ three-phase region was located at =17 mol% Y₂O₃ (83 mol% ZrO₂). Below 17 mol% Y₂O₃, ZrO₂ solid solution coexisted with Cr₂O₃. Cr₂O₃ appears to be slightly soluble in ZrO₂(ss).     

Electrical Conductivity in the ZrO2-Rich Region of Several M2O3—ZrO2 Systems

The electrical conductivity of M₂O₃-ZrO₂ compositions containing 6 to 24 mole % M₂O₃, where M represents La, Sm, Y, Yb, or Sc, was examined. Only Sm₂O₃, Y₂O₃, and Yb₂O₃ formed cubic solid solutions with ZrO₂ over most of this substitutional range. Scandia forms a wide cubic solid solution region with ZrO₂ at temperatures above 130°C whereas the cubic solid solution region at room temperature is narrow (6 to 8 mole % Sc₂O₃). Lanthana additions to ZrO₂produced no fluorite-type cubic solid solutions within the compositional range investigated. Generally, the electrical conductivity of these cubic solid solutions increased as the size of the substituted cation decreased and the electrical conductivity for each binary system attained a maximum at about 10 to 12 mole % M₂O₃.     

Densification of Cr2O3-ZrO2 Ceramics by Sintering

Cr₂O₃ and ZrO₂ were mixed in various ratios and pressed to form compacts, which were then sintered in carbon powder. Compacts with >30 wt% Cr₂O₃ were sintered to densities >98% of true density at 1500°C. This method of sintering in carbon powder can be used to prepare very dense Cr₂O₃-ZrO₂ ceramics at a relatively low temperature, (∼1500°C) without additives.     

Phase Equilibration in ZrO2-Y2O3 Alloys by Liquid-Film Migration

The tetragonal ( t ) and cubic ( c ) ZrO₂ solid solutions in two-phase ZrO₂-8 wt% Y₂O₃ ceramics have low and high solute content, respectively. Annealing samples sintered at 1600°C between 700° and 1400°C requires a change in the volume fraction of the coexisting phases, as well as their equilibrium Y₂O₃ content. The enrichment in Y₂O₃ content of the c -ZrO₂ grains is accomplished by liquid-film migration involving the ubiquitous silicate grain-boundary phase, while the volume fraction of t -ZrO₂ increases by the nucleation and growth of cap-shaped t -ZrO₂ lenses. The interfaces between the c -ZrO₂ matrix and the growing t -ZrO₂ lenses are semicoherent.     

Hot Forging Characteristics of Fine-Grained ZrO2 and Al2O3/ZrO2 Ceramics

Preliminary results indicate that large strains (∼80%) and strain rates (0.001 s⁻¹) can be obtained without tearing (or cracking) in fine-grain ZrO₂ (0.3 μm) and Al₂O₃/ZrO₂ (1 μm) ceramics. Alumina develops crystallographic and morphological texture as previously reported by Heuer et al.¹     

Phase Relationships in the ZrO2-Sc2O3 and ZrO2-In2O3 Systems

Zirconia-rich subsolidus phase relationships in the ZrO₂–Sc₂O₃ and ZrO₂–In₂O₃ systems were investigated. Phase inconsistencies in the ZrO₂–Sc₂O₃ system resulted from a diffusionless cubic-to-tetragonal ( t' ) phase transformation not being recognized in the past. Through three different measuring techniques, along with microstructural observations, the solubility limits of the tetragonal and cubic phases were determined.     

High-Toughness Ce-TZP/Al2O3 Ceramics with Improved Hardness and Strength

Simulataneous additions of SrO and Al₂O₃ to ZrO₂ (12 mol% CeO₂) lead to the in situ formation of strontium aluminate (SrO · 6Al₂O₃) platelets (∼0.5 μm in width and 5 to 10 μm in length) within the Ce-TZP matrix. These platelet-containing Ce-TZP ceramics have the strength (500 to 700 MPa) and hardness (13 to 14 GPa) of Ce-TZP/Al₂O₃ while maintaining the high toughness (14 to 15 MPa ± m^1/2) of Ce-TZP. Optimum room-temperature properties are obtained at SrO/Al₂O₃ molar ratios between 0.025 and 0.1 for ZrO₂ (12 mol% CeO₂) with starting Al₂O₃ contents ranging between 15 and 60 vol%. The role of various toughening mechanisms is discussed for these composite ceramics.     

Formation, Characterization, and Hot Isostatic Pressing of Cr2O3-Doped ZrO2 (0,3 mol% Y2O3) Prepared by Hydrazine Method

In the ZrO₂-Cr₂O₃ system, metastable t -ZrO₂ solid solutions containing up to 11 mol% Cr₂O₃ crystallize at low temperatures from amorphous materials prepared by the hydrazine method. The lattice parameter c decreases linearly from 0.5149 to 0.5077 nm with increased Cr₂O₃ content, whereas the lattice parameter a is a constant value ( a = 0.5077 nm) regardless of the starting composition. At higher temperatures, transformation (decomposition) of the solid solutions proceeds in the following way: t (ss)→ t (ss) + m + Cr₂O₃→ m + Cr₂O₃. Above 11 mol% Cr₂O₃ addition, c-ZrO₂ phases are formed in the presence of Cr₂O₃. The t -ZrO₂ solid solution powders have been characterized for particle size, shape, and surface area. They consist of very fine particles (15–30 nm) showing thin platelike morphology. Dense ZrO₂(3Y)-Cr₂O₃ composite ceramics (∼99.7% of theoretical) with an average grain size of 0.3 μm have been fabricated by hot isostatic pressing for 2 h at 1400°C and 196 MPa. Their fracture toughness increases with increased Cr₂O₃ content. The highest K _Ic value of 9.5 MPa·;m^1/2 is achieved in the composite ceramics containing 10 mol% Cr₂O₃.     

Tape Casting of Al2O3/ZrO2 Laminated Composites

Fracture toughness of ZrO₂-toughened alumina could he increased by macroscopic interfaces, such as those existing in laminated composites. In this work, tape casting was used to produce A/A or A/B laminates, where A and B can be Al₂O₃, Al₂O₃/5 vol% ZrO₂, and Al₂O₃/l0 vol% ZrO₂. An increase of toughness is observed, even in the Al₂O₃/Al₂O₃ laminates.     

Effects of Y2O3 and ZrO2 on the Densification of Si3N4-Zr(Y)O2 Composites

The effects of ZrO₂ and Y₂O₃ on the densification of hotpressed Si₃N₄-Zr(Y)O₂ composites have been studied. High density could not be obtained by the addition of pure or 3-mol%-Y₂O₃-doped ZrO₂ in this composite; however, nearly full density (>97%) could be obtained in Si₃N₄ using 6- and 8-mol%-Y₂O₃-doped ZrO₂. It is concluded that Y₂O₃ diffusing out from the added Zr(Y)O₂ promoted the densification and that ZrO₂ also had some role in the formation of an oxynitride glass.     

Conversion from β-Ce2O3·11Al2O3 to α-Al2O3 in Tetragonal ZrO2 Matrix

Composites of β-Ce₂O₃·11Al₂O₃ and tetragonal ZrO₂ were fabricated by a reductive atmosphere sintering of mixed powders of CeO₂, ZrO₂ (2 mol% Y₂O₃), and Al₂O₃. The composites had microstructures composed of elongated grains of β-Ce₂O₃·11Al₂O₃ in a Y-TZP matrix. The β-Ce₂O₃·11Al₂O₃ decomposed to α-Al₂O₃ and CeO₂ by annealing at 1500°C for 1 h in oxygen. The elongated single grain of β-Ce₂O₃·11Al₂O₃ divided into several grains of α-Al₂O₃ and ZrO₂ doped with Y₂O₃ and CeO₂. High-temperature bending strength of the oxygen-annealed α-Al₂O₃ composite was comparable to the β-Ce₂O₃·11Al₂O₃ composite before annealing.     

Structure of Incoherent ZrO2/Al2O3 Interfaces

High-resolution electron microscopy was used to image incoherent ZrO₂/Al₂O₃ interfaces in ZrO₂-toughened Al₂O₃ containing intragranular ZrO₂. These particles are generally spherical but are sometimes faceted. High-resolution electron micrographs provide atomic-level information on the interfacial structure. For spherical particles, both ledgelike images and misfit dislocation-like images accommodated the lattice misfit, depending on the orientation of the interface, while faceted particles imply at least one low-energy ZrO₂/Al₂O₃ interface.