共查询到20条相似文献,搜索用时 0 毫秒
1.
Bezrukov D. E. Kornev N. S. Makarichev N. A. Mineev K. V. Nazarov A. V. Tregubenko D. A. 《Measurement Techniques》2021,63(10):834-838
Measurement Techniques - This article presents the technique of radio interferometry measurements and a theoretical estimate of the measuring error of the reflecting surface displacement. The... 相似文献
2.
3.
用圆弧极板型差动式电容传感器测量主轴回转精度时的误差分析 总被引:1,自引:0,他引:1
定量地分析了圆弧极板型差动电容式传感器在测量主轴回转误差运动时的原理误差。指出不能忽略主轴截面形状误差的1、5、7阶谐波的影响,其余均可剔除或忽略。 相似文献
4.
本文依据JJG517-2009《出租汽车计价器计量检定规程》,对出租汽车计价器使用误差的不确定度进行评定。 相似文献
5.
《IEEE transactions on instrumentation and measurement》1983,32(1):110-116
This paper reviews the National Bureau of Standards (NBS) preision noise measurements program for antenna systems which have been made using Cassiopeia A and the moon. The Earth Terminal Measurement System (ETMS) was developed by NBS to make measurements of figure of merit (G/T), and the noise equivalent flux (NEF). The accuracy of the noise measurements are, typically, between 5 and 15 percent for systems with antenna gains between 51 and 65 dB and frequencies between 1 and 10 GHz. Key words?antenna gain; antenna half-power beamwidth; atmospheric loss; Cassiopeia A; earth terminal measurement system; figure of merit; moon; noise equivalent flux; noise measurement; radio stars; satellite communication. 相似文献
6.
针对已校准球板标准器,采用工业CT锥束扫描,参照GB/T 34874.3-2017《产品几何技术规范(GPS)X射线三维尺寸测量机第3部分:验收检测和复检检测》对Zeiss型号METROTOM 1500的工业CT进行长度测量不确定度分析与评定,确保其量值溯源至国家基准. 相似文献
7.
针对模拟万用表在测量电阻(电容或电感)时产生的误差,通过误差理论的分析方法,导出了相对误差与基本误差之间的关系,得出了相对误差是产生测量误差的主要因素,并提出了如何减少测量误差和提高测量准确度的方法。同时,也对测量非正弦波电压及失真的正弦波电压时产生的误差,提出了相应的分析方法,并定性的分析和介绍了定度系数和波形因数,提出了如何计算或修正测量误差的方法。 相似文献
8.
9.
10.
11.
12.
13.
14.
15.
An algorithm is proposed for calculating the confidence interval of a measurement error in terms of its partial components and a method is given for implementing it in the form of a programmed calculator. 相似文献
16.
17.
18.
19.
20.
本文介绍齿轮啮合分离测试技术的测量齿轮误差修正技术,它运用最小区域法计算测量齿轮的压力角和螺旋角误差对其进行修正,利用切比雪夫多项多拟合测量齿轮的形状误差进行修正,试验结果表明修正技术可大大降低了测量齿轮精度要求,能使工作的配对件作为测量齿轮。 相似文献