Deterioration Mode of Barium-Containing NOx Storage Catalyst

Barium-containing NO _x storage catalyst showed serious deactivation under thermal exposure at high temperatures. To elucidate the thermal deterioration of the NO _x storage catalyst, four types of model catalyst, Pt/Al₂O₃, Ba/Al₂O₃, Pt–Ba/Al₂O₃, and a physical mixture of Pt/Al₂O₃ + Ba/Al₂O₃ were prepared and their physicochemical properties such as BET, NO TPD, TGA/DSC, XRD, and XPS were evaluated while the thermal aging temperature was increased from 550 to 1050°C. The fresh Pt–Ba/Al₂O₃ showed a sorption capacity of 3.35 wt%/g-cat. but the aged one revealed a reduced capacity of 2.28 wt%/g-cat. corresponding to 68% of the fresh one. It was found that this reduced sorption capacity was directly related to the deterioration of the NO _x storage catalyst by thermal aging. The Ba on Ba/Al₂O₃ and Pt–Ba/Al₂O₃ catalysts began to interact with alumina to form Ba–Al solid alloy above 600°C and then transformed into stable BaAl₂O₄ having a spinel structure. However, no phase transition was observed in the Pt/Al₂O₃ catalyst having no barium component, even after aging at 1050°C.     

Influence of the Storage Material on the Storage of NOx at Low Temperatures

The NO _x storage performance at low temperature (100–200 °C) has been studied for model NO _x storage catalysts. The catalysts were prepared by sequentially depositing support, metal oxide and platinum on ceramic monoliths. The support material consisted of acidic aluminium silicate, alumina or basic aluminium magnesium oxide, and the added metal oxide was either ceria or barium oxide. The NO _x conversion was evaluated under net-oxidising conditions with transients between lean and rich gas composition and the NO _x storage performance was studied by isothermal adsorption of NO₂ followed by temperature programmed desorption of adsorbed species. The maximum in NO _x storage capacity was observed at 100 °C for all samples studied. The Pt/BaO/Al₂O₃ catalyst stored about twice the amount of NO _x compared with the Pt/Al₂O₃ and Pt/CeO₂/Al₂O₃ samples. The storage capacity increased with increasing basicity of the support material, i.e. Pt/Al₂O₃·SiO₂ < Pt/Al₂O₃ < Pt/Al₂O₃ · MgO. Water did not significantly affect the NO _x storage performance for Pt/Al₂O₃ or Pt/BaO/Al₂O₃.     

Characterisation by TPR, XRD and NOx Storage Capacity Measurements of the Ageing by Thermal Treatment and SO2 Poisoning of a Pt/Ba/Al NOx-Trap Model Catalyst

The deactivation of a Pt/Ba/Al₂O₃ NO _x -trap model catalyst submitted to SO₂ treatment and/or thermal ageing at 800 °C was studied by H₂ temperature programmed reduction (TPR), X-ray diffraction (XRD) and NO _x storage capacity measurements.The X-ray diffractogram of the fresh sample exhibits peaks characteristic for barium carbonate. Thermal ageing leads to the decomposition of barium carbonate and to the formation of BaAl₂O₄. The TPR profile of the sulphated sample shows the presence of (i) surface aluminium sulphates, (ii) surface barium sulphates, (iii) bulk barium sulphates. The exposure to SO₂ after ageing leads to a small decrease of the surface barium-based sulphates, expected mainly as aluminate barium sulphates. This evolution can be attributed to a sintering of the storage material. TPR experiments also show that thermal treatment at 800 °C after the exposure to SO₂ involves the decomposition of aluminium surface sulphates to give mainly bulk barium sulphates, also pointed out by XRD. Thus, the thermal treatment at 800 °C leads to a stabilization of the sulphates.These results are in accordance with the NO _x storage capacity measurements. On non-sulphated catalysts, the treatment at 800 °C induces to a decrease of the NO _x storage capacity, showing that barium aluminate presents a lower NO _x storage capacity than barium carbonate. Sulphation strongly decreases the NO _x storage capacity of catalysts, whatever the initial thermal treatment, showing that barium sulphates inhibit the NO₂ adsorption. Moreover, the platinum activity for the NO to NO₂ oxidation is lowered by thermal treatments.     

Changes in Ba Phases in BaO/Al2O3 upon Thermal Aging and H2O Treatment

The effects of thermal aging and H₂O treatment on the physicochemical properties of BaO/Al₂O₃ (the NO_x storage component in the lean NO_x trap systems) were investigated by means of X-ray diffraction (XRD), BET, TEM/EDX and NO₂ TPD. Thermal aging at 1000 °C for 10 h converted dispersed BaO/BaCO₃ on Al₂O₃ into low surface area crystalline BaAl₂O₄. TEM/EDX and XRD analysis showed that H₂O treatment at room temperature facilitated a dissolution/reprecipitation process, resulting in the formation of a highly crystalline BaCO₃ phase segregated from the Al₂O₃ support. Crystalline BaCO₃ was formed from conversion of both BaAl₂O₄ and a dispersed BaO/BaCO₃ phase, initially present on the Al₂O₃ support material after calcinations at 1000 and 500 °C, respectively. Such a phase change proceeded rapidly for dispersed BaO/BaCO₃/Al₂O₃ samples calcined at relatively low temperatures with large BaCO₃ crystallites observed in XRD within 10 min after contacting the sample with water. Significantly, we also find that the change in barium phase occurs even at room temperature in an ambient atmosphere by contact of the sample with moisture in the air, although the rate is relatively slow. These phenomena imply that special care to prevent the water contact must be taken during catalyst synthesis/storage, and during realistic operation of Pt/BaO/Al₂O₃ NO_x trap catalysts since both processes involve potential exposure of the material to CO₂ and liquid and/or vapor H₂O. Based on the results, a model that describes the behavior of Ba-containing species upon thermal aging and H₂O treatment is proposed.     

Thermal ageing phenomena and strategies towards reactivation of NO x - storage catalysts

The thermal ageing and reactivation of Ba/CeO₂ and Ba/Al₂O₃ based NO _x -storage/ reduction (NSR) catalysts was studied on model catalysts and catalyst systems at the engine. The mixed oxides BaAl₂O₄ and BaCeO₃, which lower the storage activity, are formed during ageing above 850 °C and 900 °C, respectively. Interestingly, the decomposition of BaCeO₃ in an atmosphere containing H₂O/NO₂ leads again to NO _x -storage active species, as evidenced by comparison of fresh, aged and reactivated Pt-Ba/CeO₂ based model catalysts. This can be technically exploited, particularly for the Ba/CeO₂ catalysts, as reactivation studies on thermally aged Ba/CeO₂ and Ba/Al₂O₃ based NSR catalysts on an engine bench showed. An on-board reactivation procedure is presented, that improved the performance of a thermally aged catalyst significantly.     

Role of Support in Lean DeNOx Catalysis

FTIR and pulse thermal analysis were applied to investigate catalysts containing Pt (1 wt%)/Ba (17 wt%) supported on -Al₂O₃, SiO₂ and ZrO₂. The aim was to learn how the support material affects the thermal stability of barium carbonate and its activity in the reaction to bulk Ba(NO₃)₂. The lower thermal stability of BaCO₃ in alumina supported samples was found to influence the formation of barium nitrate during the NO _x storage process. Quantification of Ba(NO₃)₂ formed during NO _x storage indicated that for alumina supported catalysts only ca. 30% of barium present in the sample is involved in the storage process. The low thermal stability found for alumina supported barium nitrite excludes its role in the formation of barium nitrate during interaction of NO _x with the catalyst at 300 °C. The studies indicate that -Al₂O₃ plays a major role in influencing the thermal stability of BaCO₃ and Ba(NO₃)₂. This finding seems to be relevant for the higher activity of -Al₂O₃-supported catalysts in NO _x storage reduction reactions.     

NOx Adsorption Study over Pt–Ba/Alumina Catalysts: FT-IR and Reactivity Study

The NO _x storage process over Ba/Al₂O₃ and Pt–Ba/Al₂O₃ NSR catalysts has been analyzed in this study by performing experiments at 350 °C with NO₂ and NO/O₂ mixtures using different complementary techniques (Transient Response Method, in situ FT–IR and DRIFT spectroscopies). The collected data suggest that over the Pt–Ba/Al₂O₃ catalyst the NO _x storage process from NO/O₂ mixtures occurs forming at first nitrite species, which progressively evolve to nitrates. In addition, a parallel nitrate formation via disproportionation of NO₂ (formed upon NO oxidation) cannot be excluded.     

Role and distribution of different Ba-containing phases in supported Pt–Ba NSR catalysts

Pt–Ba/MeO (where MeO = Al₂O₃, CeO₂, SiO₂ and ZrO₂) NO _x storage-reduction catalysts with Ba-loading varying from 0 wt.% to 28 wt.% were investigated concerning stability of Ba phases and NO _x storage-reduction efficiency. For Pt–Ba/Al₂O₃ three different Ba-containing phases with different thermal stability are distinguished based on their interaction with the support. The relative concentration of these phases varies with the Ba-loading and NO _x storage tests indicated that the BaCO₃ phase decomposing between 400 °C and 800 °C (LT-BaCO₃) is the most efficient Ba containing phase for NO _x storage. Similar investigations of Pt–Ba catalysts supported on CeO₂, SiO₂ and ZrO₂ showed that the relative amount of LT-BaCO₃ phase depends also on the support material. NO _x storage measurements confirmed a correlation between the concentration of LT-BaCO₃ and NO _x storage efficiency. Basicity and textural properties of the support are identified as crucial parameters for efficient NO _x storage catalysts.     

Transient Surface Processes of Storage and Conversion of NOx Species on Pt–Me/Al2O3 Catalysts (Me = Ba,Ce, Cu)

The transient reactivity and surface phenomena of storage and conversion of NO _x species on Pt(1%)–Me/Al₂O₃ catalysts, where Me = Ba, Ce and Cu, were studied by the RWF (rectangular wavefront) method. The Me component has a relevant influence on the processes of surface storage and transformation. The reduction of NO _x by propene in the presence of oxygen is promoted by adding Cu to a Pt/Al₂O₃ catalyst, while cerium promotes transient conversion of NO in the absence of propene, but inhibits the reduction of NO _x in the presence of propene. Copper is suggested to be a promising element to add together with Ba for new NO _x storage-reduction catalysts due to its capacity to act both as a storage element and as promoter for NO _x reduction.     

NO x uptake mechanism on Pt/BaO/Al2O3 catalysts

The NO _x adsorption mechanism on Pt/BaO/Al₂O₃ catalysts was investigated by performing NO _x storage/reduction cycles, NO₂ adsorption and NO + O₂ adsorption on 2%Pt/(x)BaO/Al₂O₃ (x = 2, 8, and 20 wt%) catalysts. NO _x uptake profiles on 2%\Pt/20%BaO/Al₂O₃ at 523 K show complete uptake behavior for almost 5 min, and then the NO _x level starts gradually increasing with time and it reaches 75% of the inlet NO _x concentration after 30 min time-on-stream. Although this catalyst shows fairly high NO _x conversion at 523 K, only ~2.4 wt% out of 20 wt% BaO is converted to Ba(NO₃)₂. Adsorption studies by using NO₂ and NO + O₂ suggest two different NO _x adsorption mechanisms. The NO₂ uptake profile on 2%Pt/20%BaO/Al₂O₃ shows the absence of a complete NO _x uptake period at the beginning of adsorption and the overall NO _x uptake is controlled by the gas–solid equilibrium between NO₂ and BaO/Ba(NO₃)₂ phase. When we use NO + O₂, complete initial NO _x uptake occurs and the time it takes to convert ~4% of BaO to Ba(NO₃)₂ is independent of the NO concentration. These NO _x uptake characteristics suggest that the NO + O₂ reaction on the surface of Pt particles produces NO₂ that is subsequently transferred to the neighboring BaO phase by spill over. At the beginning of the NO _x uptake, this spill-over process is very fast and so it is able to provide complete NO _x storage. However, the NO _x uptake by this mechanism slows down as BaO in the vicinity of Pt particles are converted to Ba(NO₃)₂. The formation of Ba(NO₃)₂ around the Pt particles results in the development of a diffusion barrier for NO₂, and increases the probability of NO₂ desorption and consequently, the beginning of NO _x slip. As NO _x uptake by NO₂ spill-over mechanism slows down due to the diffusion barrier formation, the rate and extent of NO₂ uptake are determined by the diffusion rate of nitrate ions into the BaO bulk, which, in turn, is determined by the gas phase NO₂ concentration.     

NOx Storage and Reduction Catalysts for Automotive Lean-Burn Engines: Effect of Parameters and Storage Materials on NOx Conversion

The effect of various parameters on the NO _x conversion over NO _x storage and reduction catalysts supported on alumina was investigated. The Pt/BaO/Al₂O₃ catalyst exhibited a higher NO _x reduction activity than the Pt/Al₂O₃ catalyst under the static and cycling conditions. The activity of Pt/BaO/Al₂O₃ catalyst was improved in the cycled feedstream. The Pt/SrO/Al₂O₃ was found to have as high activity as Pt/BaO/Al₂O₃ for NO _x reduction. In order to achieve effective reduction of NO _x , NO _x storage in the form of Me(NO₃)₂ (Me = Ba or Sr) is more favorable than other nitrates and the rich condition should be chosen in such a way that the sorption capacity can be fully regenerated at a fast rate and the inhibition effect by strongly adsorbed molecules derived from C₃H₆ and CO can be minimized.     

Performance Improvement of NO x -Storage BaO/Al2O3 by Using Barium Peroxide as the Precursor of BaO

Comparison of barium peroxide, Ba(OH)₂ and Ba(NO₃)₂ as the precursor of BaO for the preparation of NO _x -storage BaO/Al₂O₃ material was carried out. The as prepared materials were calcined at 550 and 800 °C and characterized by N₂ physisorption, XRD, Raman and FT-IR spectroscopy. Measurements of the NO _x storage performances of these BaO/Al₂O₃ materials by NO₂ adsorption and NO _x -TPD experiments showed that the use of barium peroxide as the precursor of BaO inhibited the formation of BaAl₂O₄ and led to remarkable improvements in the thermal stability as well as NO _x storage capacity of the final BaO/Al₂O₃ material calcined at 800 °C.     

The NO x reduction mechanism by H2 under near isothermal conditions over Pt–Ba/Al2O3 Lean NO x Trap systems

The study of the gas-phase NO reduction by H₂ and of the stability/reactivity of NO _x stored over Pt–Ba/Al₂O₃ Lean NO _x Trap systems allowed to propose the occurrence of a reduction process of the stored nitrates occurring via to a Pt-catalyzed surface reaction which does not involve, as a preliminary step, the thermal decomposition of the adsorbed NO _x species.     

Sulfur deactivation and regeneration of Pt/BaO/Al2O3 and Pt/SrO/Al2O3 NO x storage catalysts

Transient experiments were performed to study sulfur deactivation and regeneration of Pt/BaO/Al₂O₃ and Pt/SrO/Al₂O₃ NO _x storage catalysts. It was found that the strontium-based catalysts are more easily regenerated than the barium-based catalysts and that a higher fraction of the NO _x storage sites are regenerated when H₂ is used in combination with CO₂ compared to H₂ only.     

Influence of the Type of Reducing Agent (H2, CO, C3H6 and C3H8) on the Reduction of Stored NOX in a Pt/BaO/Al2O3 Model Catalyst

In this investigation, a comparative study for a NO _X storage catalytic system was performed focusing on the parameters that affect the reduction by using different reductants (H₂, CO, C₃H₆ and C₃H₈) and different temperatures (350, 250 and 150 °C), for a Pt/BaO/Al₂O₃ catalyst. Transient experiments show that H₂ and CO are highly efficient reductants compared to C₃H₆ which is somewhat less efficient. H₂ shows a significant reduction effect at relatively low temperature (150 °C) but with a low storage capacity. We find that C₃H₈does not show any NO _X reduction ability for NO _X stored in Pt/BaO/Al₂O₃ at any of the temperatures. The formation of ammonia and nitrous oxide is also discussed.     

NOx storage capacity,SO2 resistance and regeneration of Pt/(Ba)/CeZr model catalysts for NOx-trap system

NOx storage capacity, sulphur resistance and regeneration of 1wt%Pt/Ce_0.7Zr_0.3O₂ (Pt/CeZr) and 1wt%Pt/10wt%BaO/Ce_0.7Zr_0.3O₂ (Pt/Ba/CeZr) catalysts were studied and compared to a 1wt%Pt/10wt%BaO/Al₂O₃ (Pt/Ba/Al) model catalyst submitted to the same treatments. Pt/Ba/CeZr presents the best NOx storage capacity at 400 °C in accordance with basicity measurements by CO₂ TPD and Pt/CeZr shows the better performance at 200 °C mainly due to a low sensitivity to CO₂ at this temperature. For all samples, sulphating induces a detrimental effect on NOx storage capacity but regeneration at 550 °C under rich conditions generally leads to the total recovery of catalytic performance. However, the nearly complete sulphur elimination is only observed on Pt/CeZr. Moreover, an oxidizing treatment at 800 °C leads to partial sulphates elimination on the Pt/CeZr catalyst whereas a stabilization of sulphates on Ba containing species is observed.     

Steam effect on NO x reduction over lean NO x trap Pt–BaO/Al2O3 model catalyst

The effect of steam on NO _x reduction over lean NO _x trap (LNT) Pt–Ba/Al₂O₃ and Pt/Al₂O₃ model catalysts was investigated with reaction protocols of rich steady-state followed by lean–rich cyclic operations using CO and C₃H₈ as reductants, respectively. Compared to dry atmosphere, steam promoted NO _x reduction; however, under rich conditions the primary reduction product was NH₃. The results of NO _x reduction and NH₃ selectivity versus temperature, combined with temperature programmed reduction of stored NO _x over Pt–BaO/Al₂O₃ suggest that steam causes NH₃ formation over Pt sites via reduction of NO _x by hydrogen that is generated via water gas shift for CO/steam, or via steam reforming for C₃H₈/steam. During the rich mode of lean–rich cyclic operation with lean–rich duration ratio of 60 /20 s, not only the feed NO, but also the stored NO _x contributed to NH₃ formation. The NH₃ formed under these conditions could be effectively trapped by a downstream bed of Co²⁺ exchanged Beta zeolite. When the cyclic operation was switched into lean mode at T < 450 °C, the trapped ammonia in turn participated in additional NO _x reduction, leading to improved NO _x storage efficiency.     

Role of cobalt on γ-Al2O3 based NO x storage catalyst

Co/Pt/Ba/γ-Al₂O₃, Co/Ba/γ-Al₂O₃, Pt/Ba/γ-Al₂O₃, Co/Pt/γ-Al₂O₃, Ba/γ-Al₂O₃, Pt/γ-Al₂O₃, and Co/γ-Al₂O₃ type catalysts were prepared by a conventional impregnation method, and their NO _x storage capacities were evaluated by colorimetric assay. Co-containing catalysts had a higher NO _x storage capacity than that of Co-free counterparts. The role of each component, especially Co, for the catalysts prepared was investigated by using in-situ FTIR. The high NO _x storage for Co-containing catalysts including Co/Ba/γ-Al₂O₃ and Co/Pt/Ba/γ-Al₂O₃ is mainly due to the formation of Co₃O₄ on the catalyst surface identified by XAFS.     

A Study on the Properties and Mechanisms for NO x Storage Over Pt/BaAl2O4-Al2O3 Catalyst

The NO_x storage catalyst Pt/BaAl₂O₄-Al₂O₃ was prepared by a coprecipitation--impregnation method. For fresh sample, the barium mainly exists as the BaAl₂O₄ phase except for some BaCO₃ phase. The BaAl₂O₄ phase is the primary NO _x storage phase of the sample. EXAFS and TPD were used for investigating the mechanism of NO _x storage. It is found that two kinds of Pt sites are likely to operate. Site 1 is responsible for NO chemisorption and site 2 for oxidizing NO to nitrates and nitrites. When NO adsorbs on the sample below 200 °C, it mainly chemisorbs in the form of molecular states. Such adsorption results in an increase of the coordination magnitude of Pt-O, and a decrease of that of Pt-Pt and Pt-Cl. The coordination distance of Pt-Pt, Pt-Cl and Pt-O also increases. When the adsorption occurs above 200 °C, NO can be easily oxidized by O₂, and stored as nitrites or nitrates at the basic BaAl₂O₄. Site 2 is regenerated quickly. A high adsorption temperature is favorable for nitrate formation.