A dual current feedback op amp in CMOS technology

A CMOS circuit configuration implementing a current feedback or transimpedance op amp (CFB op amp) is presented. The architecture of the circuit is derived from similar bipolar CFB op amps. The properties of the CMOS implementation are similar to those of its bipolar counterparts, i.e., a high slew rate and a bandwidth which is independent of the closed-loop gain when the op amp is used with current feedback. Further, it is shown how two CFB op amps can be connected to achieve a non-slew-rate-limited voltage-mode op amp.     

A high precision micropower operational amplifier

An operational amplifier configuration implemented as a true micropower high precision op amp is described. It includes a well controlled and predictable DC biasing network that is insensitive to variations in temperature, supply voltages, and process. Also, it permits single supply operation. Excellent DC precision characteristics, comparable to or better than the very best precision op amps currently available, are realized yet at micropower levels. By simply increasing the biasing currents, a version of this design operates in general purpose applications without any degradation in its high precision characteristics. Thus, the AC performance levels of general purpose op amps are attained at a fraction of supply current. This device is fabricated using a standard bipolar IC process; an ion-implanted JFET is added to simplify biasing.     

A high-performance full-wave rectifier circuit

A new circuit that enables basic operational amplifiers (op amps) such as the LM741 to produce precise full-wave rectification for frequencies up to and exceeding 100 kHz without waveform distortion is presented. The circuit is based on a standard op amp precise rectifier that is modified by the inclusion of a current conveyor to improve the rectifying process.     

A multiplexed switched capacitor filter bank

A technique is introduced which allows several integrator capacitors to be multiplexed onto a single operational amplifier. As a result, the op amp can be shared by several switched capacitor filter channels, drastically reducing the number of op amps required for filter banks. Twenty second-order filters have been implemented in a circuit using only two op amps and 2.5 mm/SUP 2/. The design of this system is presented and its performance is discussed. Some loss of signal energy is shown to occur during the multiplexing operations, which reduces filter Q. Causes of this charge loss are described, and its effects on performance are modeled. The design of the op amp used is presented, which incorporates a new system of input stage biasing and differential to single-ended conversion, as well as other features.     

A macromodel for integrated all-MOS operational amplifiers

A macromodel for integrated all-MOS operational amplifiers is developed with reference to circuits where the settling behavior of the op amps is of particular concern. Expressions for the values of the elements of the macromodel are obtained from typical measured characteristics. It is shown that the proposed macromodel can satisfactorily predict both small-signal and large-signal behavior of the op amps.     

Design for testability of embedded integrated operationalamplifiers

The operational amplifier (op amp) is one of the most encountered analog building blocks. In this paper, the problem of testing an integrated op amp is treated. A new low-cost vectorless test solution, known as oscillation test, is investigated to test the op amp. During the test mode, the op amps are converted to a circuit that oscillates and the oscillation frequency is evaluated to monitor faults. The tolerance band of the oscillation frequency is determined using a Monte Carlo analysis taking into account the nominal tolerance of all important technology and design parameters. Faults in the op amps under test which cause the oscillation frequency to exit the tolerance band can therefore be detected. Some Design for Testability (DfT) rules to rearrange op amps to form oscillators are presented and the related practical problems and limitations are discussed. The oscillation frequency can be easily and precisely evaluated using pure digital circuitry. The simulation and practical implementation results confirm that the presented techniques ensure a high fault coverage with a low area overhead     

Current mode instrumentation amplifier with rail-to-rail input and output

This paper presents the results from an investigation on the implementation of Current Mode Instrumentation Amplifiers (CMIAs) with rail-to-rail operational amplifiers (op amp) with a gm control circuit. The objective of employing rail-to-rail op amps in the implementation of a CMIA is the improvement of the common-mode operation range. The enhancement of the input common mode range (ICMR) is obtained using op amps with a rail-to-rail input stage followed by a cascode-based output stage. A prototype of the CMIA was implemented in standard 0.6 μm XFAB CMOS technology. Test results showed that the CMIA common mode range was extended but with moderated CMRR. To minimize this issue the amplifier was re-designed and sent to fabrication. Simulations with the components variations included were performed and showed the enhancement of the CMRR can be expected.     

高性能结型场效应对管及其在ASIC中的应用

采用结型场效应管作为输入级的专用集成电路,一般都具有高速宽带以及高输入阻抗的特点。场效应管与双极型器件相结合,已成为新型专用型集成运算放大器的主要发展方向之一。国内在这些专用集成电路的研制工作中所面临的主要困难,是高耐压高频结型场效应对管的工艺制作。本文在介绍高性能结型场效应对管在ASIC中的应用及其工艺试验情况。     

一种折叠共源共栅运算放大器的设计

折叠共源共栅运放结构的运算放大器可以使设计者优化二阶性能指标,这一点在传统的两级运算放大器中是不可能的。特别是共源共栅技术对提高增益、增加PSRR值和在输出端允许自补偿是有很用的。这种灵活性允许在CMOS工艺中发展高性能无缓冲运算放大器。目前,这样的放大器已被广泛用于无线电通信的集成电路中。介绍了一种折叠共源共栅的运算放大器,采用TSMC 0.18混合信号双阱CMOS工艺库,用HSpice W 2005.03进行设计仿真,最后与设计指标进行比较。     

Operational amplifier with 1-V rail-to-rail multipath-driven outputstage

A bipolar operational amplifier (op amp) with a rail-to-rail multipath-driven output stage that operates at supply voltages down to 1 V is presented. The bandwidth of this output stage is as high as possible, viz, equal to that of one of the output transistors, loaded by the output capacitance. The output voltage can reach both supply rails within 100 mV and the output current is ±15 mA. The op amp is designed to be loaded by a 100-pF capacitor and the unity-gain bandwidth is 3.4 MHz at a 60° phase margin. The voltage gain is 117 dB and the CMRR is 100 dB. The frequency behavior of the multipath-driven (MPD) topology has an improved performance when compared to that of previously presented low-voltage output stages. A figure of merit F_M for low-voltage op amps has been defined as the bandwidth-power ratio     

不同结构CMOS运算放大器电路的电离辐射效应

介绍了在相同工艺条件下 ,N沟和 P沟输入两种不同结构 CMOS运算放大器电路的电离辐照响应规律及各子电路对电特性的影响情况 .结果表明 :由辐照感生的氧化物电荷引起的N沟镜像负载的不对称是导致 P沟输入运放电特性衰降的主要机制 ;而由氧化物电荷和界面态引起的 N沟差分对的漏电增大则是造成 N沟输入运放电路性能变差的主要原因     

A new nonlinear time-domain op-amp macromodel using thresholdfunctions and digitally controlled network elements

A general-purpose nonlinear macromodel for the time-domain simulation of integrated circuit operational amplifiers (op amps), either bipolar or MOS, is presented. Three main differences exist between the macromodel and those previously reported in the literature for the time domain. First, all the op-amp nonlinearities are simulated using threshold elements and digital components, thus making them well suited for a mixed electrical/logical simulator. Secondly, the macromodel exhibits a superior performance in those cases where the op amp is driven by a large signal. Finally, the macromodel is advantageous in terms of CPU time. Several examples are included illustrating all of these advantages. The main application of this macromodel is for the accurate simulation of the analog part of a combined analog/digital integrated circuit     

Changing technology-banish the 741! [op amp]

Pick up a current electronics text and you're likely to find the 741 op amp not only used, but also showcased. It's the op amp of choice for lab experiments, treatment of innards, etc. This is truly amazing when you consider that the 741 is nearly 30 years old! Of course op amps should be presented they can be used to implement a remarkable range of circuit functions. An inexpensive op amp can give near-ideal performance in certain practical applications. Getting something to work is infectious-the first op amps gave a whole generation the opportunity to build analog functions that really worked. But, like all technologies, op amp development never ceased; there have been some serious developments over the last 30 years!     

Macromodeling of integrated circuit operational amplifiers

A macromodel has been developed for integrated circuit (IC) op amps which provides an excellent pin-for-pin representation. The model elements are those which are common to most circuit simulators. The macromodel is a factor of more than six times less complex than the original circuit, and provides simulated circuit responses that have run times which are an order of magnitude faster and less costly in comparison to modeling the op amp at the electronic device level. Expressions for the values of the elements of the macromodel are developed starting from values of typical response characteristics of the op amp. Examples are given for three representative op amps. In addition, the performance of the macromodel in linear and nonlinear systems is presented. For comparison, the simulated circuit performance when modeling at the device level is also demonstrated.     

A Novel Method for Bandwidth and Phase Margin Enhancement of Folded-Cascode Amplifier

This article describes a method to enhance bandwidth and phase margin of conventional folded-cascode op amps. It achieves a larger bandwidth and/or phase margin in folded-cascode CMOS op amps than those of a conventional one in a given CMOS process. For the same bandwidth the new method allows a larger phase margin, and for a given phase margin a larger bandwidth can be obtained. Also, for equal bandwidth, power consumption of the new folded-cascode is lower than the traditional one with similar load.     

模拟运算电路运算误差分析

模拟运算电路在测控领域有广泛应用。运算误差是评价运算电路性能的重要指标之一。确定影响运算误差的主要因素和估算运算误差的大小,对指导运算电路设计和评价运算电路性能,都是必要的。文章探讨了引起模拟运算电路运算误差的几种主要因素,给出了它们引起的运算误差的估算方法,讨论了在模拟运算电路设计中减小运算误差的相应措施。结论可用于指导模拟运算电路设计和运算误差评价。     

Leveraged Current Mirror Op Amp

A small change to the standard current mirror op amp configuration is shown to improve performance, with few, if any, disadvantages. Adding a pair of fixed current sources allows reduced operating-point current in the output stage, while the resulting leveraging effect increases slew rate. For equal total power dissipation, the new configuration improves DC gain and gain-bandwidth (GBW) over conventional current-mirror and folded cascode op amps, as shown by hand analyses and SPICE simulations. Also, because of increased input stage transconductance, the new configuration reduces thermal and flicker noise.     

Novel chaotic oscillator configuration using a diode-inductor composite

A general sinusoidal oscillator configuration is designed and then modified for chaos using a second-order nonlinear grounded diode-inductor composite. The configuration has an operating frequency that can be electronically tuned by varying the gain of an inverting amplifier stage. In addition to this amplifier, a single positive-type second generation current conveyor (CCII+), two noninverting integrators and two grounded resistors are required. The case where one of the integrators is replaced with an all-pass filter is investigated. Since the configuration is designed at a functional level, different circuit realizations are possible. Experimental results and PSpice simulations of a constructed implementation based on current feedback op amps are included. Numerical simulations of the derived chaotic mathematical models using a piecewise linear approximation of the diode current-voltage characteristics are also shown.     

High-gain gaas mesfet op amp

A gain enhancement technique for GaAs MESFET op amps is presented. It uses positive feedback to cancel the output conductance between the driver and active load transistors in a common-source amplifier configuration. An op amp using this technique was implemented in a 1-µm non-self-aligned GaAs MESFET process. The op amp exhibited a dc gain of 60 dB and a unity-gain frequency of 840 MHz.Please address all correspondence to C.A.T. Salama.     

A high-swing 2-V CMOS operational amplifier with replica-amp gainenhancement

A general gain-enhancement technique for operational amplifiers using a replica amplifier is described. Unlike conventional techniques such as cascoding, which increases the gain by increasing the output resistance, the replica-amp technique increase the gain by matching the main and the replica amps. Among the advantages of the replica-amp technique are low supply, high swing, and effectiveness with resistive loads. This technique has been demonstrated in a 1.2-μm CMOS two-stage op amp. Operating from ±1-V supplies, the op amp has an effective open-loop dc gain of greater than 10 000, while maintaining a high swing of 100 mV from either supply rails. The gain-enhancement circuit is shown to have only a small effect on the settling time experimentally, analytically, and in SPICE simulation