A model with length scales for composites with periodic structure. Steady state heat conduction problem

A new high-order model for analysing distribution of temperature in periodic composites is proposed. The original scalar elliptic problem with Y-periodic coefficients (Y is a cube) is replaced with a vectorial elliptic problem of constant coefficients. The unknown fields are: the averaged distribution of temperature and the vector field which stands for perturbation of the temperature within the cells of periodicity. The recovery of temperature in the original composite is given by the approximation: 0(x)=0(x) +h ^a (x/) _a (x) analogous with the first terms of the two-scale asymptotic expansion known from the homogenization theory. The functions h are defined as approximations of the solutions to the basic cell problems. In contrast to the two-scale expansion the expression for satisfies the boundary condition.     

The tensile strength and ductility of continuous fibre composites

The plastic instability approach has been applied to the tensile behaviour of a continuous fibre composite. It is shown that the combination of two components with different strengths and degrees of work-hardening produces a new material with a new degree of work-hardening, which may be determined by the present analysis. Expressions for the elongation at rupture and the strength of a composite have been obtained and the results of the calculation are compared with some experimental data.List of symbols V _f volume fraction of fibres in composite - , , true strain of fibre, matrix and composite - s true stress - , , nominal stress on fibre, matrix and composite - _*, _*, _* critical stress of fibre, matrix and composite (ultimate tensile strength) - _*, _* critical strain of separate fibre and matrix - _* critical strain of composite - Q external load - A cross-sectional area - A ₀ initial value of area     

Relationship between the energy supply parameters and the physicochemical l characteristics of polymer compositions during drying and thermal processing

The effect of the type of energy supply on the formation of temperature and concentration fields in the thermal processing of polymer compositions is considered.Notation T₀, T initial and current temperature of the coating - T_m temperature of the air - =(T-T_o)/(T_m-T₀) dimensionless temperature of the coating - a thermal diffusivity - A absorption power of the coating - D diffusion coefficient - thermal conductivity - c thermal capacity - density - _k convective heat transfer coefficient - i number of moles of reacting groups per unit volume of polymer - K₀ factor in front of the exponential - R gas constant - u concentration - Q thermal effect of the reaction - q_n density of the incident radiant flux - =x/ dimensionless coordinate over the thickness of the coating - Ki=Aq_n /(T_m-T₀) Kirpichev criterion characterizing the thermal effect of the reaction - Ki_p=Qi/c (T_m-T₀) analog of the Predvoditelev criterion, characterizing the rate of occurrence of a chemical excess in the system - Bu= Bouguer criterion - Lu=D/a Lykov number - Fo=a/² Fourier number - Bi= _k Biot number Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 39, No. 1, pp. 26–33, July, 1980.     

Thermal conductivity of hydrocarbons in the naphthene group under high pressures

The thermal conductivity of hydrocarbons in the naphthene group has been experimentally determined. An equation is now proposed for calculating the thermal conductivity over the given temperature and pressure ranges.Notation thermal conductivity - ₂₀ and ₃₀ values of the thermal conductivity at 20 and 30°C, respectively - t₀,P₀ thermal conductivity at t₀, p₀ - _t p thermal conductivity at temperature t and under pressure P - change in thermal conductivity - P pressure - P_melt melting pressure - P₀ atmospheric pressure - t₀ 20°C temperature - T, t temperature - T_cr critical temperature - temperature coefficient of thermal conductivity - ₂₀ temperature coefficient of density - density - ₂₀ density at 20°C - _cr critical density - M molar mass - =T/T_cr referred temperature - v specific volume - v₀ specific volume at 20°C - v change in specific volume - _{3 0} a coefficient - B (t) a function of the temperature - S a quadratic functional - W_i, weight of the i-th experimental point - _i error of the i-th experimental value of thermal conductivity - B _{y, =0.6} value of B (t) at T = 0.6T_cr - B = B (t)/B_{, =0.6} referred value of coefficient B (t) Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 41, No. 3, pp. 491–499, September, 1981.     

The morphology of α′ martensite in a two-phase (α+γ) Fe-Cr-Ni stainless steel

Both lath-shaped and martensites are induced by tensile deformation within of a two-phase ( + ) Fe-Cr-Ni stainless steel, forms from the through the at an intersection of two crystals. These are observed both when is surrounded by and when borders . The amount of strain at which both and nucleate, increases with test temperatures in the range –196 to 50° C. Adjacent laths are either twin-related, or 5, 9, 15 or 19° off the twin relationship, as found by analysing electron diffraction patterns.     

Coaxial variable-length resonator for determining the electromagnetic parameters of materials at normal and higher temperatures

Conclusions It is possible by means of the above resonator, according to our analysis and in the absence of air gaps between the sample and the line, to evaluate the real components and of permeability and permittivity respectively in the range of 2 to 100 with an error between ±3% and ±10% in the temperature range from room temperature to +400°C, and the imaginary components and (for tan and tan in the range of 0.001 to 2) with an error of 7 to 20% over the same temperature range.     

Breakup of an anomolously viscous liquid film in a centrifugal force field

An equation is obtained for the breakup radius with consideration of tipping moments and Laplacian pressure forces acting on the liquid ridge at the critical point.Notation K, n rhenological constants - density - surface tension - r current cup radius - R maximum cup radius - r_c critical radius for film breakup - ¯r=¯r=r/R dimensionless current radius - ¯r_c=r_c/R dimensionless critical radius - ₀, _c actual and critical film thicknesses - current thickness - R_r ridge radius - h₀ ridge height - h current ridge height - ₀ limiting wetting angle - current angle of tangent to ridge surface - angle between axis of rotation and tangent to cup surface - angular velocity of rotation - q volume liquid flow rate - v₁ and v meridional and tangential velocities - =4vv _lm/r,=4v_m/r dimensionless velocities - M moments of surface and centrifugal forces - M_v moment from velocity head - p_r pressure within ridge - P_vm pressure from velocity head - p_m, p_pm pressures from centrifugal force components tangent and normal to cup surface - deviation range of breakup radius from calculated value - ¯r_max, ¯r_min limiting deviations of breakup radius - _c angle of tangent to curve _c/°₀=f(¯r) at critical point - t random oscillation of ratio _c/_c Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 39, No. 1, pp. 51–56, July, 1980.     

Singularity parametersε andκ for interface cracks in transversely isotropic piezoelectric bimaterials

Two parameters, and (Suo et al., 1992), are of key importance in fracture mechanics of piezoelectric material interfaces. In this paper, it is shown, for any transversely isotropic piezoelectric (TIP) bimaterial, that one of the two parameters and always vanishes but the other one remains non-zero. Physically, it means that the non-oscillating crack-tip generalized stress field singularity exists for some TIP bimaterials (with vanishing ). Consequently, TIP bimaterials can be classified into two classes: one with vanishing performed crack tip generalized stress field oscillating singularity and the other one with vanishing is independent from the oscillating singularity. Some numerical results for and are given too.     

The dielectric properties of glass-ceramic-on-metal substrates for microelectronics packaging

The dielectric properties of some glass-ceramic-on-metal substrates have been determined over the frequency range 500 Hz to 5 MHz using a.c. bridge techniques. The substrates consisted of cordierite-based glass-ceramics screen printed on molybdenum. For glass layers of thickness greater than 100 m both the permittivity, and the dielectric loss, , are frequency independent over this frequency range at room temperature giving the value of =6.5 and tan =8×10^–3; the room-temperature data are consistent with the universal law of dielectric response. The variation of permittivity with temperature has also been examined and, below 120 °C, the temperature coefficient [(–1) (+2)]^–1 (/T)_p, was found to be 1.3×10^–5 K^–1. The results are compared with those previously reported for Al₂O₃ and AIN substrates.     

Thermal Expansion and Isothermal Compressibility of TlIn1 – xNdxSe2 (0 ≤ x≤ 0.08) Crystals

The thermal expansion coefficient () and isothermal compressibility ( _T ) of TlIn_{1 – x} Nd _x Se₂(0 x 0.08) crystals were measured between 77 and 400 K. In the range 77–160 K, both and _T increase with temperature, the increase in being much steeper. At higher temperatures, and _T change very little. The observed composition dependences of and _T are interpreted in terms of energy-band structure.     

Effect of crystalline phase, orientation and temperature on the dielectric properties of poly (vinylidene fluoride) (PVDF)

The effect of crystalline phase, uniaxial drawing and temperature on the real () and imaginary () parts of the relative complex permittivity of poly (vinylidene fluoride) (PVDF) was studied in the frequency range between 10² and 10⁶ Hz. Samples containing predominantly and phases, or a mixture of these, were obtained by crystallization from a DMF solution at different temperatures. phase samples were also obtained from melt crystallization and from commercial films supplied by Bemberg Folien. Different molecular orientations were obtained by uniaxial drawing of and phase samples. The results showed that the crystalline phase exerts strong influence on the values of and , indicating that the _a relaxation process, associated with the glass transition of PVDF, is not exclsively related to the amorphous region of the polymer. An interphase region, which maintains the conformational characteristics of the crystalline regions, should influence the process decisively. The molecular orientation increased the values of for both PVDF phases and modified its dependence with temperature over the whole frequency range studied. The influence of the crystallization and molecular orientation conditions on the dc electric conductivity (_dc) were also verified. The value of _dc was slightly higher for samples crystallized from solution at the lowest temperature and decreased with draw ratio.     

Measurements of the dynamic input impedance of a dc SQUID

The impedance of a circuit coupled magnetically via a mutual inductanceM _i to a dc SQUID of geometric inductanceL is modified by the dynamic input impedance of the SQUID, which can be characterized by the flux-to-current transfer functionJ J/;J is the current circulating in the SQUID loop and is the flux applied to the loop. At the same time, the SQUID is modified by the presence of the input circuit: in the lumped circuit approximation, one expects its inductance to be reduced toL ^r=(1– _e ² )L, where _e is an effective coupling coefficient. Calculations of J using an analog simulator are described and presented in the form of a dynamic inductance and a dynamic resistance versus bias currentI and . Experimental measurements of and were made on a planar, thin-film SQUID tightly coupled to a spiral input coil that was connected in series with a capacitorC _i to form a resonant circuit. Thus,J was determined from the change in the resonant freqency and quality factor of this circuit as a function ofI and . At low bias currents (low Josephson frequencies) the measured values of were in reasonable agreement with values simulated for the reduced SQUID, while at higher bias currents (higher Josephson frequencies) the measured values were in better agreement with values simulated for the unscreened SQUID. Similar conclusions were reached in the comparison of the experimental and simulated values of the flux-to-voltage transfer functionV . The reduction in the screening at the higher Josephson frequencies is believed to result from the parasitic capacitanceC _p between the SQUID and the input coil. In contrast to the behavior of the input inductance, the change in the input resistance R _i could not be explained in terms of the dynamic impedance of the SQUID reflected into the input circuit. Instead, R _i was dominated by capacitive feedback between the output of the SQUID and the input circuit viaC _p . The experimental values of R _i were satisfactorily explained by a simplified model that predicts R _i –M _iV ^r (C _p /C _i ).     

The Interplay of Electronic and Nuclear Magnetism in PtFe x at Milli-, Micro-, and Nanokelvin Temperatures

We have measured ac susceptibility, nuclear magnetic resonance, and nuclear heat capacity of two PtFe _x samples with concentrations of magnetic impurities x = 11 ppm and 41 ppm at magnetic fields (0 ± 0.05) mTB248 mT. The susceptibility data have been measured at temperatures of 0.3 KT100 mK, no hint for nuclear magnetic ordering could be detected to a temperature of 0.3 K. The nuclear heat capacity data taken at 1.4 KT10 mK show enhanced values which scale with x at low polarization. This effect is described by a model assuming an internal magnetic field caused by the impurities. No indication for nuclear magnetic ordering could be detected to 1.4 K. The nuclear magnetic resonance experiments have been performed on these samples at 0.8 KT0.5 mK and 2.5 mTB22.8 mT as well as on three other samples with x = 5, 10, 31 ppm in a different setup at 40 KT0.5 mK and at 5.4 mTB200 mT. Spin-lattice and effective spin-spin relaxation times ₁and ₂ ^* of ¹⁹⁵ Pt strongly depend on x and on the external magnetic field. No temperature dependence of ₁and ₂ ^* could be detected and the NMR data, too, give no hint for nuclear magnetic ordering to 0.8 K.     

Phase transformations in permanent-mould-cast aluminium bronze

The phases obtained in aluminium bronze (Cu-10Al-4Fe) cast into a permanent mould were investigated. The parameters examined were the pre-heating temperature of the mould and the graphite coating thickness. The phases and ₂ were detected as well as the metastable phases and . The intermetallics of the system Fe-Al were obtained in various stoichiometric compositions. The different cooling rates of the casting resulted in two mechanisms of transformation to grains out of the unstable phase, one being nucleation and growth producing needle-shaped grains, the other exhibiting a massive transformation to spherical grains. These two mechanisms determine the changes in the size of the a grains as result of changes in the cooling rate in its various ranges.     

Mössbauer studies of α″-Fe16N2 and α′-Fe8N films

Conversion-electron Mössbauer spectra of epitaxial -Fe₁₆N₂ and -Fe₈N films have been studied and their differences are discussed in detail. The Mössbauer spectrum of -Fe₁₆N₂ can be decomposed into three subspectra, which correspond to the 4d, 8h and 4c sites. The Mössbauer spectrum of -Fe₈N can be fitted using four spectra based on a nitrogen-atom-random-distribution model. The average hyperfine field is larger (3%) for -Fe₁₆N₂ than for -Fe₈N, which is approximately consistent with a 4.1% enhancement of the magnetic moments for -Fe₁₆N₂. The iron moments tend to locate in the film plane for -Fe₁₆N₂ and to arrange perpendicularly to the film plane for -Fe₈N.     

Microstructures of titanium-aluminides produced by laser surface alloying

The microstructures of Ti-Al layers (from 43–80 at %Al) produced by laser surface alloying of titanium substrate with a powder feed technique have been investigated. The laser processing parameters were; 1.8 kW laser power, 3 mm beam diameter, 7 mm s^–1 traverse speed, and values of powder flow rates of aluminium ranging from 0.07–0.11 g s^–1. The microstructures were dendrites of ₂ and interdendritic regions of ₂+ in the Ti-43 at %Al alloy; dendrites of either ₂ or ₂+ with interdendritic in the Ti-50 at %Al alloy; dendrites of ₂+ with interdendritic in the Ti-55 at %Al alloy; single phase in the Ti-60 at %Al alloy and TiAl₃ dendrites and Al solid solution in the interdendritic regions in the Ti-80 at %Al alloy. The microstructures were fine and comparable to those produced by other methods of rapid solidification processing. The microstructures of the Ti-50 and Ti-55 at %Al alloys were in agreement with the existence of the peritectic reactions:L + andL + , in the Ti-Al system.     

Microstructural study of ε-iron-carbonitrides formed by a glow discharge technique

The microstructure and phase transformations occurring in-iron-carbonitrides have been studied by means of X-ray and electron diffraction, electron microscopy and Mössbauer spectrometry. Ordering of the interstitial atoms, N or C, results in a hexagonal unit cell for Fe₃(C, N) with parametersa=a3 andc=c wherea andc are the lattice parameters of the hexagonal close-packed (h c p) iron unit cell. Stacking faults on (0001) planes and partial dislocations with Burgers vector b=1/31 0 ¯1 0 are observed in quenched-Fe₄ (C, N). After quench-aging, the carbonitrides show a structural hardening due to the precipitation of a metastable phase. Slow cooling of-carbonitrides with less than 25 at% interstitials leads to the precipitation of-carbonitride and ferrite in-phase grains which allows the orientation relationships between the-,- and-phases to be defined and a model of the-phase--phase transformation to be proposed.     

A transmission electron microscopic study of the Bethany iron meteorite

The Bethany iron meteorite which is a part of the Gibeon shower is a fine octahedrite with zoned plessite fields of various sizes. The optically irresolvable microstructural details inside the plessitic fields have been studied by transmission electron microscopy, and the crystallographic relationships between the primary kamacite () and the parent taenite (), and between the and particles in the coarse plessite, have been examined using electron diffraction. In the case of primary kamacite the orientation-relationship with was close to the Nishiyama-Wasserman relationship, whereas, for the plessitic , the orientation-relationship with was close to Kurdjumov-Sachs. It was also found that the (111) and (110) planes were not strictly parallel. Additionally, measurements of the composition profile through the zoned plessite have been made using STEM microanalysis technique, and related to microstructure.     

Inertia of measurements with “auxiliary-wall” type heat meters

The article examines the problem of thermal inertia on the basis of an auxiliary-wall type heat meter, it demonstrates the boundaries of applicability of the approximate relationship for calculating non-steady-state heat fluxes.Notation q() non-steady-state heat flux through the heat meter - _i,a _i thermal conductivity, thermal diffusivity, and thickness of the heat meter, respectively - ₂,a ₂ thermal conductivity and thermal diffusivity, respectively, of the base of the heat meter - t() temperature gradient over the thickness of the heat meter - index of thermal inertia - time - s parameter of Laplace transform - t₁ (x, ) temperature of the heat meter at point x - t₂(x, ) temperature of the base - t_c ambient temperature - Y_q(s) transfer function from the heat flux q() to the temperature gradient t() Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 39, No. 2, pp. 298–305, August, 1980.     

Deformation approach to the evaluation of the period of initiation and growth of fatigue macrocracks

We performed experimental investigation of the opening displacements of the contours of stress concentrators (notches and cracks) for various amplitudes of cyclic loading. On the basis of experimental results, we propose a new deformation parameter _t which is a function of the notch (crack) tip opening displacement , namely, _t /(+d*), where is the radius of the tip of the notch andd* is the characteristic size of the prefracture zone. It is shown that this parameter uniquely determines the number of cyclesN _l to the initiation of a fatigue macrocrack independently of the geometry of the specimens and stress concentrators in elastic and elastoplastic materials, i.e., the dependence of _t onN ₁ is a characteristic of the material. It is experimentally demonstrated that this dependence enables one to quantitatively describe the process of fatigue fracture both in the stage of initiation of macrocracks and their propagation.Karpenko Physicomechanical Institute, Ukrainian Academy of Sciences, L'viv. Translated from Fiziko-Khimicheskaya Mekhanika Materialov, Vol. 31, No. 5, pp. 7–21, September – October, 1995.