民用建筑室内新风量检测方法影响因素的研究

新风对于稀释室内空气中的有害物质、改善室内环境有着重要的意义。新风量则是衡量新风的有效手段,目前不设独立新风系统的建筑室内新风量测量广泛采用CO_2示踪气体法。本文通过一系列实验探讨CO_2初始浓度、门窗开关方式、室外风速以及室内杂物对室内新风量检测结果的影响。实验结果表明CO_2初始浓度、门窗开关方式、室外风速、室内杂物这些因素均对新风量检测值均存在不同程度的影响,其中室外风速和室内有无杂物对新风量检测结果的影响最为明显。     

A new approach on zonal modeling of indoor environment with mechanical ventilation

This paper reports the development of a new zoning approach based on room air age, a parameter that indicates the mixing condition of the air. Zoning criteria are developed based on the deviation ratio of air age as well as location of the key source that is of concern (e.g., temperature, air pollutant). By integrating the zonal model with other models such as dynamic models for heat and moisture transfer, and source/sink models for air pollutant, the dynamic characteristics of indoor parameters such as air temperature, humidity, and pollutant concentrations can be simulated. A case study was presented for a displacement ventilated room, and simulation results using the new zonal model were compared with those using a computational fluid dynamics (CFD) model and a conventional zonal model. Results demonstrated that the new zonal model is more accurate in calculating the zonal temperature distributions than the conventional zonal model. The model is suitable for dynamic simulations (e.g., whole year) of indoor environmental parameters.     

Evaluation of the indoor air quality minimum ventilation rate procedure for use in California retail buildings

This research assesses benefits of adding to California Title‐24 ventilation rate (VR) standards a performance‐based option, similar to the American Society of Heating, Refrigerating, and Air Conditioning Engineers ‘Indoor Air Quality Procedure’ (IAQP) for retail spaces. Ventilation rates and concentrations of contaminants of concern (CoC) were measured in 13 stores. Mass balance models were used to estimate ‘IAQP‐based’ VRs that would maintain concentrations of all CoCs below health‐ or odor‐based reference concentration limits. An intervention study in a ‘big box’ store assessed how the current VR, the Title 24‐prescribed VR, and the IAQP‐based VR (0.24, 0.69, and 1.51 air changes per hour) influenced measured IAQ and perceived of IAQ. Neither current VRs nor Title 24‐prescribed VRs would maintain all CoCs below reference limits in 12 of 13 stores. In the big box store, the IAQP‐based VR kept all CoCs below limits. More than 80% of subjects reported acceptable air quality at all three VRs. In 11 of 13 buildings, saving energy through lower VRs while maintaining acceptable IAQ would require source reduction or gas‐phase air cleaning for CoCs. In only one of the 13 retail stores surveyed, application of the IAQP would have allowed reduced VRs without additional contaminant‐reduction strategies.     

An evaluation index for the control effect of the local ventilation systems on indoor air quality in industrial buildings

To evaluate the control effect on indoor air quality (IAQ) of the local ventilation systems in industrial buildings with centralized contaminant sources, a new index, namely, normalized concentration in the target zone (NC-TZ), was proposed in this paper. According to theoretical analysis, NC-TZ is non-dimensional and ranges from 0 to 1. When NC-TZ tends toward 0, the control effect of the local ventilation system on IAQ is more satisfactory. When NC-TZ tends toward 1, the control effect on IAQ is less satisfactory. The numerical simulation on a push–pull ventilation system with varying exhaust flow rates and varying distances between push and pull hoods was performed. The results demonstrate that for the same capture efficiency, changing the local ventilation system characteristics can change the control effect on the local environment. The results for obstacles at different positions also indicate that NC-TZ can clearly reflect the control effect on IAQ of the local ventilation systems in industrial buildings.     

An energy impact assessment of ventilation for indoor airborne bacteria exposure risk in air-conditioned offices

Treatment of fresh air in ventilation systems for air-conditioned offices consumes a significant amount of energy and affects the indoor air quality (IAQ). In this study, energy impact on the ventilation systems was examined against certain IAQ objectives for indoor airborne bacteria exposure risk in air-conditioned offices of Hong Kong. The relationship between thermal energy consumptions and indoor airborne bacteria exposure levels based on regional surveys was investigated. The thermal energy consumptions of ventilation systems operating for carbon dioxide (CO₂) exposure concentrations between 800 and 1200 ppmv for typical office buildings and the corresponding failure probability against some target bacteria exposure levels were evaluated. The results showed that, for a reference indoor environment at a CO₂ exposure concentration of 1000 ppmv, the predicted average thermal energy saving of ventilation system for a unit increment of the expected risk of unsatisfactory IAQ of 1% was 55 MJ m⁻² yr⁻¹ and for a unit decrement of 1%, the predicted additional thermal energy consumption was 58 MJ m⁻² yr⁻¹ respectively. This study would be a useful source of reference in evaluation of the energy performance of ventilation strategies in air-conditioned offices at a quantified exposure risk of airborne bacteria.     

An investigation on the mechanisms of instabilities and safe design of the south slope at a lignite pit (SW Turkey) based on a sensitivity approach

Turkey has significant lignite reserves which are generally being extracted using open pit mining methods. The Hüsamlar pit is one of the operated lignite pits in the well-known Mugla lignite province in SW Turkey. Some local failures and one large failure, which caused the evacuation of the Hüsamlar village located next to the slope crest and interruption in coal production, occurred along the south slope of this pit. This paper outlines the results of the field and laboratory geotechnical investigations associated with the causes and mechanisms of the instabilities, and assessments on the possible modifications in the current and planned final slope geometries to improve the stability of the south slope. Since no sufficient data on groundwater conditions in the pit were available, in order to reduce the uncertainty associated with groundwater, different pore pressure ratios (r _u) were considered and a sensitivity approach was used in the stability assessments. The back-analyses of the observed instabilities including one or more benches in the overburden indicated that the most critical modes of failure for the south slope are circular and composite sliding surfaces. Although kinematical analyses suggested that structurally controlled failures would not be expected, one local planar failure that occurred in the south slope emphasizes that the possibility of local planar sliding should be considered when the dip of bedding planes locally exceed 20° and pore pressure becomes high. In addition, the back-analyses revealed that r _u was probably between 0.3 and 0.4 and the residual shear strength along the bedding planes was critical when slope instabilities occurred along the south slope. The stability assessments for the current and the final south slope, which was planned by the mining organization operating the pit, indicated that some modifications in bench and slope geometries are necessary to achieve a factor of safety of 1.3, which is a commonly used value in open pit practice. In addition, these assessments also suggested that the most critical zone in the overburden was the thinly bedded marl in terms of stability, and at the thickest part of this material (30 m), the overall slope angles satisfying F = 1.3 at r _u values of 0.2, 0.3 and 0.4 should be 18°, 17° and 15°, respectively. Except those in the thinly bedded marl, bench widths in the overburden units and coal seam are reduced and steeper slopes with F ≥ 1.3 were achieved.     

基于PyroSim 的压入式通风巷道火灾模拟

基于 2019 年山东“11·19”火灾事故,利用 PyroSim软件构建压入式掘进巷道内的火灾模型,实现了总长 400 m、火源位于 200 m 处的掘进巷道内,风筒烧断与未烧断两种情况、不同火源功率下的火灾模拟。结果表明：在压入式巷道中发生火灾,一旦风筒烧断,火灾发展将更加迅速;一定条件下巷道中火场内被困区温度、烟气遮光率随时间推移和风流作用会迅速增大;火源功率越大,被困区受到危险的时间越短。     

某游泳馆室内气流组织数值模拟分析

以游泳馆高大空间建筑为研究对象,对室内空调系统的气流组织进行了探讨,并采用k-ε模型对游泳馆空调室内上送上回风方式气流分布进行了模拟,通过对Airpak的模拟分析了室内气流温度场、速度场的分布特点,为空调系统节能和游泳馆类建筑设计优化提供了依据。     

浅谈公共娱乐场所安全疏散设计

根据人在火灾中的行为,并结合公共娱乐场所建筑的火灾特点,对公共娱乐场所建筑的安全疏散设计进行讨论.     

Fault-tolerant control for outdoor ventilation air flow rate in buildings based on neural network

This paper describes a supervisory control scheme that adapts to the presence of the measurement faults in outdoor air flow rate control using sensor-based demand-controlled ventilation, maintains an adequate indoor air quality and minimizes the resulting increase in energy consumption. A strategy, which is based on neural network models, is employed to diagnose the measurement faults of outdoor and supply flow sensor, and accomplishes the fault-tolerant control of outdoor air flow when faults occur. The neural network models are trained using the data collected under various normal conditions. The residuals between the measurements of flow sensors and the outputs of the neural network models are used to diagnose the faults. When the fault of outdoor or supply air flow sensor occurs, the recovered estimate of outdoor or supply air flow rate obtained on the basis of the neural network models is used in the feedback control loop to regain the control of outdoor air flow. Tests using dynamic system simulation are conducted to validate the strategy. The control, IAQ and energy performances of the system under fault-tolerant control strategy in the presence of the faults in air flow sensor are also presented.     

The predictions of infection risk of indoor airborne transmission of diseases in high-rise hospitals: Tracer gas simulation

The spread of diseases from infected patients within hospitals is resulting in many human casualties. If a virus were to be transmitted through uncontrolled air movement within a hospital and were then to infect other patients or healthy visitors, it would be impossible to contain the spread of the disease. The purpose of this paper is to apply reliable boundary conditions based on previous studies in order to analyze the airflow pattern caused by the stack effect in high-rise hospitals. An analysis was carried out on the vertical airborne transmission of viruses according to the location of the infected patients. The horizontal airborne transmission based on the characteristics of the supply air diffuser and return air grille was also analyzed by using the multi-zone airflow simulation and tracer gas (CFD) simulation. In addition, this paper explored solutions to prevent the spread of airborne pathogenic bacteria by analyzing various alternatives of HVAC systems and basic data on ventilation system planning for high-rise hospitals.     

An instructional design for building energy simulation e-learning: an interdisciplinary approach

This article describes the development of a new instructional design (ISD) to promote building energy simulation (BES) education. The study is based upon education fundamentals combined with computer-based learning and hypermedia to enable the development of a BES-based distance learning system. Some cognitive tools are established such as: (i) an interdisciplinary knowledge tree of BES that can be used by professionals with different backgrounds; (ii) a hypermedia navigational aid to understand the simulation software, called the BES tool graphic organizer; (iii) a concept map with an overview of building energy performance and (iv) a cooperative problem-based learning (CPBL) environment. Furthermore, the paper also brings an analysis of the students’ comprehension – from a course applied across Brazil – by means of concept network graphs from text mining provided by the CPBL environment, showing a significant potential to develop interdisciplinary e-learning related to building energy efficiency.     

An optimal condition based maintenance scheduling for metal structures based on a multidisciplinary research approach

Abstract

Latest research findings show that the deterioration of metal coatings results due to complex combination of material and meteorological parameters. The classical maintenance scheduling do not consider complex interface of materials and meteorological parameters to determine optimal maintenance framework. The cost of recoating can be optimised through appropriate selection of coating specifications and maintenance strategy. This research provides a multidisciplinary algorithmic approach to determine cost-effective solutions for recoating. The specifications of red oxide primer coating and structural steel substrate system are considered for simulation analysis. The results show that the appropriate selection of 10% increase in coating thickness based on coating-substrate system specifications resulted in 20–25% reduction in annual patch failures which reduces 5–6% cost of recoating. Furthermore, the proposed model also simulated to compare Patch recoating and Part recoating strategy and algorithm show that the Part recoating is cost-effective as compared to Patch recoating if number of annual patch failure is greater than ‘2’ and area of the part is ‘2×’times larger than the area of the patch. Contrary, the Patch recoating results in low cost if the part area is ‘10×’ times larger than patch area and number of annual patch failures are less than ‘7’.     

Annual characteristics of ventilation and indoor air quality in detached houses using a simulation method with Japanese daily schedule model

This paper presents the results of investigations that were made on a simulation program, which calculates the temperature, the heat loads, the ventilation rates and the indoor air quality considering the Japanese daily schedule and the dweller's behaviour toward keeping comfortable indoor climate, in order to explain the effect of ventilation systems. In the investigation, the concentrations of carbon dioxide, carbon monoxide and formaldehyde are regarded as indicators of indoor air quality. Firstly, three types of systems were designed in a house model; that is a basic passive ventilation system, a passive stack ventilation system and a mechanical ventilation system. Next, the simulation was performed using the standard weather data on three cities in Japan; and the simulation made clear the annual characteristics of ventilation and indoor air quality. The results show that in a house with a passive ventilation system, there is much risk of indoor air pollution in spring, autumn and when air conditioned, and that indoor air quality in the rooms on the first floor differs from that on the second floor. Lastly, the performance of the ventilation systems and the solution methods of realizing these ventilation systems were discussed on the basis of the results of the simulation.     

室内污染物的防治及评价方法探讨

总结了目前存在的影响室内污染物的种类,着重描述了室内污染物的防治对策,并初步介绍了室内污染物评价方法,包括客观评价方法以及建议建立主观和客观相结合的评价方法,以期指导实践。     

基于MODFLOW的面状通量处理方法研究

针对国际通用软件MODFLOW缺乏面状通量处理的缺陷,基于RCH子程序(Recharge Package),开发出可实现多层面状补给和排泄的子程序包PRD(Planar Recharge and Discharge Package).应用PRD可以在模型的所有层位上进行面状补给或排泄处理.也可实现在同一层位的多次不同面...     

自然通风建筑室内气流组织优化研究

通过fluent模拟软件对诸多因素中最为关键的风向、风速、开窗位置及面积等进行了优化模拟研究。结果表明:在西安地区,南向为最佳风向,室外风速在1.3～2.5 m/s之间,基本上都能满足自然通风要求,最佳风速为1.5 m/s;综合考虑采光和自然通风因素,窗户开在墙的中间为宜;北向面积适当减小有利于自然通风在室内形成较均匀的气流,在保证建筑节能标准的前提下,增大南向窗户面积有利于自然通风。     

An experimental study on effects of increased ventilation flow on students' perception of indoor environment in computer classrooms

The effects of ventilation in computer classrooms were studied with university students (n = 355) in a blinded study, 31% were women and 3.8% had asthma. Two classrooms had a higher air exchange (4.1-5.2 ac/h); two others had a lower air exchange (2.3-2.6 ac/h). After 1 week, ventilation conditions were shifted. The students reported environmental perceptions during the last hour. Room temperature, RH, CO2, PM10 and ultra-fine particles were measured simultaneously. Mean CO2 was 1185 ppm at lower and 922 ppm at higher air exchange. Mean temperature was 23.2 degrees C at lower and 22.1 degrees C at higher air exchange. After mutual adjustment (temperature, RH, CO2, air exchange), measured temperature was associated with a perception of higher temperature (P < 0.001), lower air movement (P < 0.001), and poorer air quality (P < 0.001). Higher air exchange was associated with a perception of lower temperature (P < 0.001), higher air movement (P = 0.001), and better air quality (P < 0.001). In the longitudinal analysis (n = 83), increased air exchange caused a perception of lower temperature (P = 0.002), higher air movement (P < 0.001), better air quality (P = 0.001), and less odor (P = 0.02). In conclusion, computer classrooms have CO2 levels above 1000 ppm and temperatures above 22 degrees C. Increased ventilation from 7 l/s per person to 10-13 l/s per person can improve thermal comfort and air quality. PRACTICAL IMPLICATIONS: Computer classrooms are crowded indoor environments with a high thermal load from both students and computer equipment. It is important to control room temperature either by air conditioning, sun shields, or sufficiently high ventilation flow. A high ventilation flow is also crucial to achieving good perceived air quality. Personal ventilation flow should be at least 10 l/s. Possible loss of learning ability due to poor indoor air quality in university buildings deserves more attention.     

Experimental investigations of the indoor natural ventilation for different building configurations and incidences

This paper presents an experimental investigation of the indoor natural ventilation in terms of wind pressures on the surfaces of cubic buildings of a street located within a high density urban area. Wind tunnel tests over 1:100 scale models for four typical building patterns of a highly populated urban area have been carried out. The variables of the experiments were the building configurations and the incident wind direction. The experimental data are presented in terms of wind pressure coefficient measured on the surfaces of the buildings. The study results gave the evidence that buildings configuration and wind direction are very important factors in determining the induced natural ventilation within urban domains since they characteristically influence the flow yielding differences in wind pressures.