固化剂对低温固化环氧建筑胶性能的影响

研究了6种不同固化体系在-12～0℃温度下的固化情况,探讨了不同固化剂对胶粘剂固化反应速度、压缩强度及钢一钢拉伸剪切强度的影响。试验结果表明,MS-0021固化剂各项性能优于其他固化剂,其压缩强度值为62．56MPa,钢－钢拉伸剪切强度值为1523MPa,可满足胶粘剂的冬季施工要求。     

Room Temperature Curing Epoxy Adhesives for Elevated Temperature Service

Room Temperature curing compositions of epoxy resins with high temperature service capability (95-120°C) were formulated and evaluated. The compositions were based on selected high functionality atomatic epoxy polymers and multicomponent poly amine curing agent systems. Toughening was achieved by addition of a rubbery phase either by prereaction of the epoxy resin with carboxyl terminated (CTBN) or by amine terminated (ATBN) poly butadiene acrylonitrile. The latter elastomeric component served as a part of the poly amine curing agent.

Best results were achieved with an adhesive formulation comprising tetra glycidyl-4-4'-diaminodiphenylmethane (TGDDM) and triglycidyl ether of p-aminophenol with triethylenetetramine and addition of ATBN with a felt carrier.

Lap shear strengths of aluminum/aluminum specimens primed by silane coupling agent in the order of 22 MPa at 25°C and 11 MPa at 120°C with T-Peel strengths of 1.6N/mm at 25°C and 0.52 N/mm at 120°C, were obtained.

The thermal behaviour and transitions, the chemical and mechanical properties, the microstructure and morphology of the selected adhesive formulation were studied, using DSC, Gehman, FTIR, mechanical testing and SEM analysis, respectively.

Experimental results showed that the selected compositions could develop good high temperature (120°C) properties while cured at room temperature. Furthermore, their high temperature performance compares favorably or even exceeds that of commercially available room-temperature-curing adhesive compounds, and are competitive with elevated temperature cured film adhesives.     

Adhesives and coatings based on poly(vinyl acetal)s

Phenolic resins such as resole phenol– and cresol–formaldehyde, as well as low-molecular-weight epoxy resin based on bis(4-hydroxy phenol) cyclohexane were prepared and modified with various types of the prepared poly(vinyl acetal)s. Poly(vinyl formal), poly(vinyl isobutyral), and poly(vinyl propional) were used. This study indicated that the optimum conditions for curing phenolic or epoxy resin–poly(vinyl acetal)s adhesive compositions are of an equal weight ratio or a 2 : 1 weight ratio in the presence of phthalic anhydride (10 or 20 wt %) of resin content as a curing agent at 150°C for 20 or 60 min, respectively. The effect of acetal type on the tensile shear strength values of resin samples, cured under the previously mentioned optimum conditions for different times, was investigated. The effect of structure of cresol–formaldehyde and epoxy resins was also studied. Metallic and glass coatings from the previous pure resins and their formulated mixtures were also prepared and evaluated as varnishes or paints. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 1769–1777, 1998     

双组分高强度环氧胶粘剂的研制

根据车间内钢梁上吊车轨道安装底板与钢梁粘接的具体要求,研制了一种中温固化双组分环氧胶粘剂。探讨了E-51、E-39D和纳米碳酸钙用量对甲组分粘度的影响,测试了不同促进剂的胶粘剂凝胶时间并研究了粘接表面处理、中温固化时间对胶粘剂剪切强度的影响。结果表明,通过选用不同粘度的环氧树脂并添加纳米碳酸钙,控制甲组分粘度在8～20Pa.s,选用促进剂M3份,表面制备并采用偶联剂处理后,100℃下固化2h后,该胶铝-铝、钢-钢剪切强度可达45MPa和51MPa,实现了胶粘体系中温高强度快速固化。室温放置20h后钢-钢剪切强度为5.8MPa,可以安装加热设备以便后固化。     

一种回转体类构件用中低温固化环氧树脂体系研究

采用等温黏度实验和浇铸体力学性能测试来优选自制改性固化剂CUR–1的配比,通过不同升温速率下的固化过程差示扫描量热并对固化物进行傅立叶变换红外光谱分析,确定了体系的固化制度,研制出一种适用于发动机壳体或结构复杂的回转体类结构件的碳纤维湿法缠绕树脂基复合材料的中低温固化环氧树脂体系,用湿法缠绕工艺制作单向纤维缠绕成型复合材料环(NOL环)并进行了性能测试。结果表明:当CUR–1的含量为15份时,树脂体系具有适于湿法缠绕工艺的黏度和使用期,树脂可在80℃完全固化,同时浇铸体拉伸强度为84 MPa,拉伸弹性模量为3.8 GPa,断裂伸长率为5.4%,热变形温度为131℃。该树脂体系与纤维粘结性好,NOL环力学性能高,NOL环拉伸强度为2 451 MPa,拉伸弹性模量为146 GPa,层剪切强度为55 MPa。     

曼尼希改性二乙烯三胺环氧建筑胶固化剂的制备

选用苯酚（P）、甲醛（F）对二乙烯三胺（DETA）进行曼尼希反应改性,研究了产物黏度、胺值与原料配比的关系。将改性的固化剂与环氧树脂E51进行配胶浇注,研究了胶体的力学性能与潮湿环境下的粘接性能。结果表明,P、DETA与F物质的量比[n（P）：n（DETA）：n（F）]=1．5：1．5：1．5的产物综合性能最佳。该固化剂黏度适宜（6542mPa·s）,与E51配胶浇注后,拉伸强度为40MPa,压缩强度达80MPa,潮湿环境下的钢一钢剪切强度为9．2MPa,与混凝土的粘接拉伸强度达47MPa,为混凝土内聚破坏。     

Aminimide as hardener/curing promotor for one part epoxy resin composition

Three kinds of aminimide compounds were examined as latent hardeners/promotors for epoxy resins. Since aminimides are thermolyzed to generate tertiary amine and isocyanate, the compounds are useful as polymerization initiators for the epoxy group as well as promotors for epoxy–acid anhydride reaction. The pot life was over 30 days at 40°C for a formulated one-part epoxy resin system. In comparison with epoxy resins cured with conventional hardeners, several interesting characteristics of the mechanical and electrical properties were observed. In particular, the epoxy resins cured by aminimides exhibited high tensile strength and high impact strength, which make them excellent curing agents for adhesive applications. The reasons for these unique properties are discussed.     

适用于低温固化的低黏度高强度环氧树脂结构胶

以碳酸丙烯酯(PC)为活性稀释剂、自制增韧型421固化剂/快固型DETA(二乙烯三胺)固化剂作为复合固化剂,制备环氧树脂(EP)结构胶。研究结果表明:当m(EP)∶m(PC)∶m(421)∶m(DETA)=100∶20∶24∶6.0时,EP结构胶的初始黏度(60 mPa.s)相对较低,其强度和韧性俱佳(拉伸强度为45 MPa、压缩强度为70 MPa和钢/钢剪切强度为12.0 MPa);该EP结构胶可低温固化(5℃或常温固化7 d后的拉伸强度基本一致),也是一款适用于冬季施工的低黏度高强度EP结构胶。     

多元醇与环氧树脂共混改性的研究

采用自制的聚酯多元醇对环氧树脂进行共混改性,对改性环氧树脂固化物的拉伸强度、断裂伸长率、冲击强度、剪切强度等进行了考察,同时探讨了多元醇分子量变化及加入量不同对性能的影响。结果表明,改性后的体系韧性得到了明显的提高,如冲击强度从13.2kJ/m2提高到26.3kJ/m2。室温剪切强度从24.2MPa提高到43.75MPa。     

聚氨酯改性室温固化环氧结构胶粘剂的研究

采用聚氨酯预聚体改性环氧树脂,制备了高性能室温固化环氧结构胶粘剂,研究了聚氨酯预聚体加入量对环氧结构胶剪切强度、冲击强度和拉伸强度等指标的影响,利用扫描电镜(SEM)对环氧胶固化物的冲击断裂面进行了分析。结果表明,聚氨酯预聚体的加入可显著提高环氧胶粘剂的韧性。采用NCO质量分数为3.86%的甲苯二异氰酸酯/聚醚多元醇预聚体(TDI/N220)改性环氧树脂,加入量为20 g/(100 g环氧树脂)时,环氧结构胶粘剂的综合性能最佳,剪切强度为20.8 MPa,冲击强度为44.2 kJ/m2,拉伸强度为17.4 MPa。     

环氧树脂/三羟甲基三聚氰胺硅化物固化体系阻燃性能与耐热性研究

利用三聚氰胺和甲醛合成了三羟甲基三聚氰胺（TMM）,将其与正硅酸乙酯(TEOS)反应得到三羟甲基化三聚氰胺硅化物（TMMSi）。将TMMSi与环氧树脂复合,采用4,4'-二氨基二苯基甲烷(DDM)作固化剂来制备环氧树脂/TMMSi固化物,并对固化物的热性能和阻燃性能进行了分析。结果表明,与环氧树脂/TMM固化物相比,环氧树脂/TMMSi固化物的玻璃化转变温度变化较小,高温耐热性提高不明显,但是阻燃性能得到了大幅度提高。当TMMSi含量为15份时,环氧树脂/TMMSi固化物的极限氧指数达到29.6 %,比纯环氧树脂固化物提高了40 %。     

Mechanical properties of an epoxy resin toughened by polyester

The epoxy resins were toughened by 4–24 phr polyester with average molecular weight 1.9×10⁴ g/mol in this investigation. The mechanical properties were examined and dynamic mechanics analyses were performed for the epoxy resins before and after the modification. The toughening mechanism of polyester to epoxy resin is discussed in light of the scanning electronic microscopy observation of the fracture surfaces. The results showed that the impact strength and tensile strength of the modified epoxy resin were remarkably greater than those of the unmodified cured epoxy resin. The most suitable composition for the modified epoxy resin was the addition of 16 phr polyester, which led to 138 and 46% increments in the impact strength and the tensile strength, respectively. And the mechanical properties depended greatly on the congregating state of polyester added. The polyester dispersing in the epoxy matrix was amorphous when its addition was less than or equal to 12 phr, and was sphere crystals when the addition was over 16 phr. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3384–3389, 2003     

聚氨酯改性中温快速固化环氧粘合剂的制备与应用

以聚四氢呋喃醚、异佛尔酮二异氰酸酯、2-乙基咪唑为原料,合成了以2-乙基咪唑封端的聚氨酯,并用于改性环氧树脂E-44.利用傅立叶红外分析仪、示差扫描量热仪、拉伸试验机等手段对其与环氧树脂混合物的凝胶时间、固化温度、解封情况、拉伸剪切强度等性能进行了研究.结果表明,咪唑封端的聚氨酯可以在130℃下较好地解封,每10份E-...     

Curing of epoxy resin contaminated with water

Epoxy resins used for reinforcement of bridges and buildings are explored in the light of both curing rates and mechanical properties when resins are contaminated with water in outdoor construction. The developed resin is composed of a conventional resin of bisphenol A diglycidyl ether and a hardener with a polyoxipropyldiamine base. Curing rates were obtained by time variation of the near infrared absorbance of amine groups in the hardener at various water contents. They obeyed the second‐order reaction law with respect to the hardener, of which the activation energy was 70 kJ mol⁻¹. Water increased the reaction rate. Mechanical properties such as ultimate tensile strength, adhesive shear stress, and flexural strength were measured at various water contents for the developed epoxy resin and the commercially available low‐temperature epoxy resin. The developed cured resin shows not only higher mechanical strengths but also much less deterioration by water than the conventional cured resin. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 214–220, 2001     

Effect of Phenol/Formaldehyde Stoichiometry on the Modification of Epoxy Resin Using Epoxidized Novolacs

ABSTRACT

Unmodified epoxy resins based on bisphenol A exhibit brittleness and low elongation after cure. This article reports the results of a study for improving the properties of epoxy resin by blending with suitable thermosets. Hybrid polymer networks of diglycidyl ether of bisphenol A (DGEBA) resin with epoxidized phenolic novolac resins (EPN) containing phenol and formaldehyde in different stoichiometric ratios were prepared by physical blending. The modified epoxy resins were found to exhibit improved mechanical and thermal properties compared to the neat resin. DGEBA resins containing 2.5 to 20 wt% of epoxidized novolac resins (EPN) prepared in various stoichiometric ratios (1:0.6, 1:0.7, 1:08, and 1:0.9) between phenol and formaldehyde were cured using a room temperature amine hardener. The cured samples were tested for mechanical properties such as tensile strength, modulus, elongation, and energy absorption at break. All the EPNs are seen to improve tensile strength, elongation, and energy absorption at break of the resin. The blend of DGEBA with 10 wt% of EPN-3 (1:0.8) exhibits maximum improvement in strength, elongation, and energy absorption. EPN loading above 10 wt% is found to lower these properties in a manner similar to the behavior of any filler material. The property profiles of epoxy–EPN blends imply a toughening action by epoxidized novolac resins and the extent of modification is found to depend on the molar ratio between phenol and formaldehyde in the novolac.     

Preparation and Application of a New Curing Agent for Epoxy Resin

A new curing agent based on palmitoleic acid methyl ester modified amine (PAMEA) for epoxy resin was synthesized and characterized. Diglycidyl ether of bisphenol A (DGEBA) epoxy resins cured with different content of PAMEA along with diethylenetriamine (DETA) were prepared. The mechanical properties, dynamic mechanical properties, thermal properties, and morphology were investigated. The results indicated that the PAMEA curing agent can improve the impact strength of the cured epoxy resins considerably in comparison with the DETA curing agent, while the modulus and strength of the cured resin can also be improved slightly. When the PAMEA/epoxy resin weight ratio is 30/100, the comprehensive mechanical properties of the cured epoxy resin are optimal; at the same time, the crosslinking density and glass transition temperature of the cured epoxy resin are maximal.     

动态固化聚丙烯／马来酸酐接枝聚丙烯／滑石粉／环氧树脂复合材料研究

将动态硫化技术应用于热塑性树脂／填料／热固性树脂复合体系，制备了动态固化聚丙烯(PP)／马来酸酐接枝PP(PP-g-MAH)/滑石粉(Talc)／环氧树脂(EP)复合材料。研究了动态固化PP／PP-g-MAH/Talc／EP复合材料的界面作用、形态结构、力学性能以及热稳定性。实验结果表明：PP／PP-g—MAH的加入，可明显增加PP/Talc复合材料的界面作用。在动态固化PP／PP-g-MAH/Talc／EP复合材料中，PP和Talc两相界面更加模糊，动态固化EP进一步增加了PP和Talc间的界面作用。当EP的用量超过5份时，部分EP呈颗粒状分布在PP基体中。与PP／PP-g-MAH/Talc／EP和PP／PP-MAH-Talc／EP复合材料相比，动态固化PP／PP-g-MAH/Talc／EP复合材料的冲击强度、拉伸强度和弯曲模量均有明显提高。当EP用量超过5份时，复合材料的冲击强度和断裂伸长率明显降低，但拉伸强度和弯曲模量继续增加。热分析表明动态固化PP／PP-g-MAH/Talc／EP复合材料具有较高的热稳定性。     

Structural Adhesive Bonds to Primers Electrodeposited on Steel

Adhesive bond strength and durability were investigated for steel substrates which had been cathodically electroprimed before bonding. Lap shear and torsional impact strengths of two model epoxy adhesives were evaluated. Very poor strengths and durability were found for one adhesive, which was cured with a mixture of three amine curing agents. Scanning electron microscopy and analysis of primer susceptibility to interaction with the curing agents suggested that, for the high concentrations of curing agent in the amine-cured adhesive, chemical and physical degradation of the primer occurred during cure at elevated temperature.

For the second adhesive, which was cured with a single imidazole catalyst, excellent strength and durability were obtained, with no evidence of primer degradation. Surprisingly, for this adhesive, strengths to primed steel were up to 88% higher than to cleaned (i.e., degreased) bare steel. The concurrent improvements in environmental durability over bare steel, as assessed by water immersion and salt spray accelerated exposures, were attributed to the more favourable surface energetics of the adhesive/primer interface.     

环氧树脂/马来海松酸酐聚酰胺的固化反应及产物性能研究

以马来海松酸酐为原料,通过与多元胺(二乙烯三胺、三乙烯四胺、四乙烯五胺)进行酰胺化反应,合成了3种环氧树脂固化剂马来海松酸酐聚酰胺,分别命名为聚酰胺样品Ⅰ、聚酰胺样品Ⅱ、聚酰胺样品Ⅲ。利用傅里叶红外光谱仪(FT-IR)、热重分析仪(DTA)、拉力机等分析测试手段,对环氧树脂/马来海松酸酐聚酰胺体系固化产物的特征性能进行了表征。结果表明,环氧树脂分别与3种聚酰胺样品按理论质量配比100:51、100:45、100:45混匀后,在室温放置6 h后再于80℃固化4 h,可完全固化,环氧树脂/聚酰胺样品Ⅰ剪切强度可达21.6 MPa,3种固化体系热分解温度均大于300℃,可望在对剪切强度、耐热等级要求较高的固化剂领域得到广泛应用。     

Enhancement of Epoxy Resin/Copper Heterojunction by Introduction of Sulfur‐Containing Polymers

Summary: Epoxy resins are widely used in electronics and electric industries because of their superior properties. In recent years, excellent bonding properties for metals (e.g., copper, gold, aluminium, silver, etc.), to which it is hard to adhere, have become desirable for epoxy resins in the electric and electronics industrial fields. However, epoxy resins have only poor bonding strength to the metals. In order to increase the heterojunction strength between epoxy resins and copper, the introduction of sulfur, providing strong interactions with metals, was investigated. TDP polyester and MPS polythioesters containing sulfur moieties were employed as the sulfur‐containing modifiers for the epoxy resin. Epoxy resins containing a modifier (5–20 phr) and a curing agent were cured between copper plates at 120 °C for 2 h and at 170 °C for 2 h. The effect of the added modifiers was evaluated by the lap‐shear testing method. It could be demonstrated that MPS polythioesters have a beneficial effect on the enhancement of the epoxy resin/copper heterojunction. The most effective example was the addition of 20 phr of the MPS_7 polythioester, which increased the lap shear strength from 5.7 to 17 MPa.

Improvement of lap shear strengths of adhesive copper joints by sulfur‐containing modifiers.