Design and implementation of sub 0.5‐V OTAs in 0.18‐μm CMOS

A family of bulk‐driven CMOS operational transconductance amplifiers (OTAs) has been designed for extremely low supply voltages (0.3‐0.5 V). Three OTA design schemes with different gain boosting techniques and class AB input/output stages are discussed. A detailed comparison among these schemes has been presented in terms of performance characteristics such as voltage gain, gain‐bandwidth product, slew rate, circuit sensitivity to process/mismatch variations, and silicon area. The design procedures for all the compared structures have been developed. The OTAs have been fabricated in a standard 0.18‐μm n‐well CMOS process from TSMC. Chip test results are in good agreement with theoretical predictions and simulations.     

On the input common‐mode voltage range of CMOS bulk‐driven input stages

In this paper the response of a bulk‐driven MOS Metal‐Oxide‐Semiconductor input stage over the input common‐mode voltage range is discussed and experimentally evaluated. In particular, the behavior of the effective input transconductance and the input current is studied for different gate bias voltages of the input transistors. A comparison between simulated and measured results, in standard 0.35‐µm CMOS Complementary Metal‐Oxide‐Semiconductor technology, demonstrates that the model of the MOS transistors is not sufficiently accurate for devices operating under forward bias conditions of their source‐bulk pn junction. Therefore, the fabrication and the experimental evaluation of any solution based on this approach are highly recommended. A technique to automatically control the gate bias voltage of a bulk‐driven differential pair is proposed to optimize the design tradeoff between the effective input transconductance and the input current. The proposed input stage was integrated as a standalone block and was also included in a 1.5‐V second‐order operational transconductance amplifier (OTA)‐C lowpass filter. Experimental results validate the effectiveness of the approach. Copyright © 2010 John Wiley & Sons, Ltd.     

gm‐Extraction for rail‐to‐rail input stage linearization

Transconductance of rail‐to‐rail input stages in low‐voltage operational amplifiers depends on the presence of a large common mode input signal. Corrections must be implemented in order to correct it. Nevertheless, techniques actually used, based on switching or feedforward, still give relevant deviation from the constant transconductance condition. In this paper we present a new architecture based on extraction and feedback to the gain control, directly of the value of the transconductance of the amplifier to be controlled. This quantity does not contain the signal to be amplified, and thus once fed back, it does not affect the overall stage gain. A ‘reciprocal’ circuit, which performs the 1/x mathematical function, is introduced in order to achieve this extraction. Copyright © 2005 John Wiley & Sons, Ltd.     

0.5‐V bulk‐driven differential amplifier

A new 0.5‐V fully differential amplifier is proposed in this article. The structure incorporates a differential bulk‐driven voltage follower with conventional gate‐driven amplification stages. The bulk‐driven voltage follower presents differential gain equal to unity while suppressing the input common‐mode voltage. The amplifier operates at a supply voltage of less than 0.5 V, performing input transconductance almost equal to a gate transconductance and relatively high voltage gain without the need for gain boosting. The circuit was designed and simulated using a standard 0.18‐µm CMOS n‐well process. The low‐frequency gain of the amplifier was 56 dB, the unity gain bandwidth was approximately 3.2 MHz, the spot noise was 100 nV/√Hz at 100 kHz and the current consumption was 90 μΑ. Copyright © 2012 John Wiley & Sons, Ltd.     

An 11‐μ W, 9‐bit fully differential,cyclic/algorithmic ADC in 0.13 μm CMOS

This paper describes a fully differential, cyclic, analogue‐to‐digital converter (ADC). It utilizes a 4‐bit binary weighted capacitor array to obtain 9‐bit resolution. The ADC uses an operational amplifier to suppress supply voltage variations. The operational amplifier with the slew‐rate detection is used to increase the speed of the ADC. The ADC is fabricated in IBM 0.13 μm CMOS process and occupies 650 × 850μm² active area. At 10 kS/s sampling rate, the ADC consumes 11 μW. In order to test immunity of the ADC on the supply voltage variations, static and dynamic performance of the ADC is measured with triangular supply voltage (V _{D C}  = 1.5 V, V _{A C}  = 200mV _pp, f  = 1 kHz). The measured peak of differential nonlinearity and integral nonlinearity is  + 0.26/ − 0.67 and  + 0.65/ − 0.59, respectively. At 250 Hz, effective number of bit is 8.4 bits, S F D R  = 66.7 dB and S N D R  = 52.6 dB. Copyright © 2016 John Wiley & Sons, Ltd.     

0.5‐V bulk‐driven OTA and its applications

A new 0.5‐V bulk‐driven operational transconductance amplifier (OTA), designed in 50 nm CMOS technology, is presented in the paper. The circuit is characterized by improved linearity and dynamic range obtained for MOS devices operating in moderate inversion region. Some basic applications of the OTA such as a voltage integrator and a second‐order low‐pass filter have also been described. The filter is compared to other low‐voltage filters presented in the literature. Copyright © 2013 John Wiley & Sons, Ltd.     

A pseudo‐differential current‐reuse structure for opamp‐sharing pipelined analog‐to‐digital converters

In this paper, a power efficient pseudo‐differential (PD) current‐reuse structure is presented to alleviate the memory effects of opamp‐sharing in pipelined analog‐to‐digital converters. To implement the PD current‐reuse structure, a switched‐capacitor circuit is introduced for multiplying digital‐to‐analog converter, which has a slight modification compared with the conventional switching scheme with no power penalty. In the proposed multiplying digital‐to‐analog converter circuit, the common‐mode offset amplification of the PD structures is eliminated. Moreover, a PD current‐reuse amplifier is developed from the telescopic structure with an inverter‐based gain‐boosting circuit. The effectiveness of the proposed structure is evaluated in comparison with existing current‐reuse techniques. Copyright © 2014 John Wiley & Sons, Ltd.     

Programmable feedforward linearized CMOS OTA for fully differential continuous‐time filter design

In this paper, a feedforward linearization method for programmable CMOS operational transconductance amplifier (OTA) is described. The proposed circuit technique is developed using simple source‐coupled differential pair transconductors, a feedback‐loop amplifier for self‐adjusting transcoductance (g_m) and a linear reference resistor (R). As a result, an efficient linearization of a transfer characteristic of the OTA is obtained. SPICE simulations show that for 0.35µm AMS CMOS process with a single +3V power supply, total harmonic distortion at 1 V_pp and temperature range from ?30 to +90°C is less than ?49.3 dB in comparison with ?35.8 dB without linearization. Moreover, the input voltage range of linear operation is increased. Power consumption of the linearized OTA circuit is 0.86 mW. Finally, the OTA is used to design a third‐order elliptic low‐pass filter in high‐frequency range. The cut‐off frequency of the operational transconductance amplifier‐capacitor (OTA‐C) filter is tunable in the range of 322.6 kHz–10 MHz using the feedforward linearized OTAs with the digitally programmable current mirrors. Copyright © 2009 John Wiley & Sons, Ltd.     

Low‐voltage bulk‐driven input stage with improved transconductance

A low‐voltage input stage constructed from bulk‐driven PMOS transistors is proposed in this paper. It is based on a partial positive feedback and offers significant improvement of both input transconductance and noise performance compared with those achieved by the corresponding already published bulk‐driven structures. The proposed input stage offers also extended input common‐mode range under low supply voltage in relevant to a gate‐driven differential pair. A differential amplifier based on the proposed input stage is also designed, which includes an auxiliary amplifier for the output common‐mode voltage stabilization and a latch‐up protection circuitry. Both input stage and amplifier circuits were implemented with 1 V supply voltage using standard 0.35µm CMOS process, and their performance evaluation gave very promising results. Copyright © 2010 John Wiley & Sons, Ltd.     

Robust design of CMOS amplifiers oriented to settling‐time specification

In this paper, we propose a new approach for the robust design of complementary metal‐oxide‐semiconductor amplifiers based on settling‐time specifications. The approach is based on the definition of the separation factors and on the analysis of their role in the settling time. We define a design strategy for being certain that an OTA satisfies the settling‐time constraint under any statistical variation of process or design parameters. The proposed strategy is applied to the transistor level design of a two‐stage amplifier and a three‐stage one. Simulation results, in good agreement with theory, confirm the validity of the proposed approach. Copyright © 2016 John Wiley & Sons, Ltd.     

A 0.6‐V sub‐mW X‐band RFSOI CMOS LNA with novel complementary current‐reused technique

A fully integrated 0.6 V low‐noise amplifier (LNA) for X‐band receiver application based on 0.18 μm RFSOI CMOS technology is presented in this paper. To achieve low noise and high gain with the constraint of low voltage and low power consumption, a novel modified complementary current‐reused LNA using forward body bias technique is proposed. A diode connected MOSFET forward bias technique is employed to minimize the body leakage and improve the noise performance. A notch filter isolator is constructed to improve the linearity of low voltage. The measured results show that the proposed LNA achieves a power gain of 11.2 dB and a noise figure of 3.8 dB, while consuming a DC current of only 1.6 mA at supply voltage of 0.6 V. Copyright © 2017 John Wiley & Sons, Ltd.     

Low‐voltage low‐power CMOS receiver front‐end for gigabit short‐reach optical communications

This article presents a new CMOS receiver analog front‐end for short‐reach high‐speed optical communications, which compensates the limited product bandwidth length of 1‐mm step‐index plastic optical fiber (SI‐POF) channels (45 MHz · 100 m) and the required large‐diameter high‐capacitance Si PIN photodetector (0.8 mm–3 pF). The proposed architecture, formed by a transimpedance amplifier and a continuous‐time equalizer, has been designed in a standard 0.18‐µm CMOS process with a single supply voltage of only 1 V, targeting gigabit transmission for simple no‐return‐to‐zero modulation consuming less than 23 mW. Experimental results validate the approach for cost‐effective gigabit SI‐POF transmission. Comparative analysis with previously reported POF receivers has been carried out by introducing a useful figure of merit. Copyright © 2012 John Wiley & Sons, Ltd.     

Ultralow‐power CMOS/SOI circuit technology

We have introduced an example of a system that embodies the concept of a ubiquitous communication service and explained the importance of low power consumption in the communicator that will serve as the bridge between the real world and the network for real‐time services in which sensor data is acquired every second. An effective solution to the problem of high energy efficiency is to employ the synergy of combining low‐voltage analog circuit technology and FD‐SOI devices. Taking advantage of that synergy to reduce the power consumption of the communicator during operation to about 10 mW and employing intermittent operation with an activity rate of less than l% would make it possible to support operation for 1 year or more with a commercial coin‐type lithium battery. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 162(3): 38–43, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20543     

Gate‐level body biasing technique for high‐speed sub‐threshold CMOS logic gates

An efficient technique for designing high‐performance logic circuits operating in sub‐threshold region is proposed. A simple gate‐level body biasing circuit is exploited to change dynamically the threshold voltage of transistors on the basis of the gate status. Such an auxiliary circuit prepares the logic gate for fast switching while maintaining energy efficiency. If 200 aJ is the target total energy per operation consumption, a two input NAND (NOR) gate designed as described here shows a delay reduction between 20% (16%) and 40% (48%), with respect to previously proposed sub‐threshold approaches. Copyright 2012 John Wiley & Sons, Ltd.     

A 0.5 V bulk‐driven voltage follower/DC level shifter and its application in class AB output stage

A simple realization of a 0.5 V bulk‐driven voltage follower/direct current (DC) level shifter designed in a 0.18 µm CMOS technology is presented in the paper. The circuit is characterized by large input and output voltage swings and a DC voltage gain close to unity. The DC voltage shift between input and output terminals can be regulated in a certain interval around zero, by means of biasing current sinks. An application of the proposed voltage follower circuit for realization of a low‐voltage class AB output stage has also been described in the paper. Finally, the operational amplifier exploiting the proposed output stage has been presented and evaluated in detail. Copyright © 2014 John Wiley & Sons, Ltd.     

Relaxing the maximum dc input amplitude vs. consumption trade‐off in differential‐input band‐pass biquad filters

This paper shows that an important part of the power consumption of a biquad band‐pass filter is associated with the feedback loop that fixes the high‐pass frequency and blocks the direct current (dc) input signals. The dc input amplitude that can be blocked is related to the maximum output current that one of the transconductors can provide, hence impacting on the required consumption through this effect. Then, a technique that efficiently blocks the dc input signal and fixes the high‐pass frequency is introduced and analyzed in depth. Moreover, an architecture for ultra‐low‐power differential‐input biquads is fully presented. The proposed architecture enables lowering the power consumption or blocking higher levels of dc input without jeopardizing the power consumption. Results show that the proposed architecture, compared with a traditional one, presents a 30% reduction in power consumption and more than doubles the dc input that can be blocked. Copyright © 2016 John Wiley & Sons, Ltd.     

A fully differential current copier for performance improvement

This paper presents a new current copier which uses a differential‐pair as its storage cell. The differential‐pair storage unit (DPSU) significantly reduces clock‐feedthrough errors and achieves high linearity, large dynamic range, and less cross‐talk noise. Therefore, the proposed high‐performance DPSU can be used to improve the speed performance of analog‐to‐digital converters which implement the proposed fully differential switched‐current technique. Copyright © 2000 John Wiley & Sons, Ltd.     

An amplifier‐offset‐insensitive and high PSRR subthreshold CMOS voltage reference

An amplifier‐offset‐insensitive complementary metal‐oxide‐semiconductor (MOS) voltage reference (CVR) circuit with high power supply ripple rejection (PSRR) is presented. Due to the novel structure of employing subthreshold MOS transistors, the proposed CVR circuit can suppress the direct current offset effects of the internal amplifier. Design considerations in optimizing the power and area consumptions and improving the PSRR are presented. The proposed CVR circuit is implemented in a standard 0.18 μm complementary MOS process. Measured results show that the reference can run with down‐to 0.9 V supply voltage, while the power consumption is only 70 nW. The measured PSRR is better than ?37 dB over the full frequency range.     

Multiple output differential OTA with linearizing bulk‐driven active‐error feedback loop for continuous‐time filter applications

A CMOS circuit realization of a highly linear multiple‐output differential operational transconductance amplifier (OTA) has been proposed. The presented approach exploits a differential pair as an input stage with both the gate and the bulk terminals as signal ports. For the proposed OTA, improved linearity is obtained by means of the active‐error feedback loop operating at the bulk terminals of the input stage. SPICE simulations of the OTA show that, for 0.35 µm AMS process, total harmonic distortion at 1.36Vpp is less than 1% with dynamic range equal to 60.1 dB at power consumption of 276 μW from 3.3 V supply. As an example, both single output and dual differential OTAs are used to design third‐order elliptic low‐pass filters. The cut‐off frequency of the filters is 1 MHz. The power consumption of the OTA‐C filter utilizing the dual output differential OTA is reduced to 1.24 mW in comparison to 2.2 mW consumed by the single output differential OTA‐C filter counterpart. Copyright © 2014 John Wiley & Sons, Ltd.     

A sub‐1 V nanopower temperature‐compensated sub‐threshold CMOS voltage reference with 0.065%/V line sensitivity

We present the design of a nanopower sub‐threshold CMOS voltage reference and the measurements performed over a set of more than 70 samples fabricated in 0.18 µm CMOS technology. The circuit provides a temperature‐compensated reference voltage of 259 mV with an extremely low line sensitivity of only 0.065% at the price of a less effective temperature compensation. The voltage reference properly works with a supply voltage down to 0.6 V and with a power dissipation of only 22.3 nW. Very similar performance has been obtained with and without the inclusion of the start‐up circuit. Copyright © 2013 John Wiley & Sons, Ltd.