首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 15 毫秒
1.
    
A unified multi‐stage power‐CMOS‐transmission‐gate‐based quasi‐switched‐capacitor (QSC) DC–DC converter is proposed to integrate both step‐down and step‐up modes all in one circuit configuration for low‐power applications. In this paper, by using power‐CMOS‐transmission‐gate as a bi‐directional switch, the various topologies for step‐down and step‐up modes can be integrated in the same circuit configuration, and the configuration does not require any inductive elements, so the IC fabrication is promising for realization. In addition, both large‐signal state‐space equation and small‐signal transfer function are derived by state‐space averaging technique, and expressed all in one unified formulation for both modes. Based on the unified model, it is all presented for control design and theoretical analysis, including steady‐state output and power, power efficiency, maximum voltage conversion ratio, maximum power efficiency, maximum output power, output voltage ripple percentage, capacitance selection, closed‐loop control and stability, etc. Finally, a multi‐stage QSC DC–DC converter with step‐down and step‐up modes is made in circuit layout by PSPICE tool, and some topics are discussed, including (1) voltage conversion, output ripple percentage, and power efficiency, (2) output robustness against source noises and (3) regulation capability of converter with loading variation. The simulated results are illustrated to show the efficacy of the unified configuration proposed. Copyright © 2003 John Wiley & Sons, Ltd.  相似文献   

2.
    
This paper presents a specific analysis of an individual basic magnetically coupled direct current‐to‐direct current (DC–DC) converter specially designed for integration in a distributed architecture of renewable energy generators for smart grid applications. In such distributed architecture dedicated for renewable energy, parallel high‐voltage DC presents many advantages over the classical centralized one. We show that in such setup, high voltage can be advantageously produced using a specific magnetically coupled boost converter, and we point out the influence of the coupling factor, generally considered equal to one, on the overall performance of the converter and on the global energy efficiency of the installation. In this study, the generalized concepts of system energy parameters of DC–DC converters are introduced and applied to the transient analysis. Consequently, the operation of a magnetic coupled DC–DC converter with a recovery stage is modeled. The simulation results are compared with those of the behavioral study, deduced from the model pointing out the large influence of the coupling factor value on the global behavior and mainly on the value of the recovery voltage, in all the various parts of the switching cycle. The renewable energy generator operating parameters, such as current and voltage values, can then be predicted in a more useful way to compute new similar DC–DC converter systems. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

3.
    
This study presents a new high step‐up, high efficiency, flyback‐forward converter. The proposed converter employs 2 transformers, operating in flyback and forward modes at different intervals, to achieve the high voltage gain. In favor of high power density, transformers have been installed on 1 core. Furthermore, all switches are turned on under zero voltage switching condition, and all diodes are turned off under zero current switching condition. Also, the proposed converter utilizes resonant operation that leads to a reduction in switching loss, turning the converter to a highly efficient one. A 150‐W prototype has been implemented to verify the theoretical analysis, and a complete analysis has been done to investigate the effect of transformers integration.  相似文献   

4.
    
In this paper, a new adaptive dual current mode control method (ADCMC) is presented, being a result of the modification of existing dual current mode control (DCMC) by introducing an adaptive current bandwidth. The ADCMC offers several important advantages over DCMC, such as no peak‐to‐average error in the inductor current, better transient response of current loop, and improved line regulation. A detailed analysis of the proposed ADCMC is performed for three types of DC–DC power electronics converters: buck, boost, and non‐inverting buck–boost converter. The performances of the ADCMC are tested with simulations and experiments. The obtained results confirm the analysis and validity of the proposed ADCMC method. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

5.
    
In this paper, a pulse width modulation DC‐DC converter with high step‐up voltage gain is proposed. The proposed converter achieves high step‐up voltage gain with appropriate duty ratio, coupled inductor, and voltage multiplier technique. The energy stored in the leakage inductor of the coupled inductor can be recycled in the proposed converter. Moreover, because both main and auxiliary switches can be turned on with zero‐voltage switching, switching loss can be reduced by soft‐switching technique. So the overall conversion efficiency is improved significantly. The theoretical steady‐state analyses and the operating principles of the proposed converter are discussed in detail for both continuous conduction mode and discontinuous conduction mode. Finally, a laboratory prototype circuit of the proposed converter is implemented to verify the performance of the proposed converter. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

6.
    
There are many applications in power electronics that demand high step‐up conversion ratio between the source and the load. A simple way of achieving such a high voltage ratio is by cascading DC–DC boost converters in a few stages. The individual converters in such a cascaded system are usually designed separately applying classical design criteria. This paper investigates the stability of the overall system of a cascade connection of two boost converters under current mode control. We first demonstrate the bifurcation behavior of the system, and it is shown that the desired periodic orbit can undergo fast‐scale period doubling bifurcation leading to subharmonic oscillations and chaotic regimes under parameter variation. The value of the intermediate capacitor is taken as a design parameter, and we determine the minimum ramp slope in the first stage required to maintain stability. It is shown that smaller capacitance values give rise to wider stability range. We explain the bifurcation phenomena using a full‐order model. Then, in order to simplify the analysis and to obtain a closed‐form expression to explain the previous observation, we develop a reduced‐order model by treating the second stage as a current sink. This allows us to obtain design‐oriented stability boundaries in the parameter space by taking into account slope interactions between the state variables in the two stages. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

7.
    
This paper proposes a novel zero‐current‐switching series resonant high‐voltage DC–DC converter with reduced component count. The series resonant inverter in the proposed topology has two power switches (insulated‐gate bipolar transistors, IGBTs), two resonant capacitors, and only one high‐voltage transformer (HVT) with center‐tapped primary windings. The power switches are connected in the form of a half‐bridge network. The leakage inductances of the transformer's primary windings together with the resonant capacitors form two series resonant circuits. The series resonant circuits are fed alternately by operating the power switches with interleaved half switching cycle. The secondary winding of the HVT is connected to a bridge rectifier circuit to rectify the secondary voltage. The converter operates in the discontinuous conduction mode (DCM) and its output voltage is regulated by pulse frequency modulation. Therefore, all the power switches turn on and off at the zero‐current switching condition. The main features of the proposed converter are its lower core loss, lower cost, and smaller size compared to previously proposed double series resonant high voltage DC–DC converters. The experimental results of a 130‐W prototype of the proposed converter are presented. The results confirm the excellent operation and performance of the converter. © 2016 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.  相似文献   

8.
    
In photovoltaic (PV) double‐stage grid‐connected inverters a high‐frequency DC–DC isolation and voltage step‐up stage is commonly used between the panel and the grid‐connected inverter. This paper is focused on the modeling and control design of DC–DC converters with Peak Current mode Control (PCC) and an external control loop of the PV panel voltage, which works following a voltage reference provided by a maximum power point tracking (MPPT) algorithm. In the proposed overall control structure the output voltage of the DC–DC converter is regulated by the grid‐connected inverter. Therefore, the inverter may be considered as a constant voltage load for the development of the small‐signal model of the DC–DC converter, whereas the PV panel is considered as a negative resistance. The sensitivity of the control loops to variations of the power extracted from the PV panel and of its voltage is studied. The theoretical analysis is corroborated by frequency response measurements on a 230 W experimental inverter working from a single PV panel. The inverter is based on a Flyback DC–DC converter operating in discontinuous conduction mode (DCM) followed by a PWM full‐bridge single‐phase inverter. The time response of the whole system (DC–DC + inverter) is also shown to validate the concept. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

9.
In this paper, a current sensorless MPPT control method for a stand‐alone‐type PV generation system is proposed. This control method offers advantages of the simplified hardware configuration and low cost by using only one sensor to measure the PV output voltage. When used as a stand‐alone‐type with a battery load, the experimental results show that the estimated values of PV output current are accurate, and the use of the proposed MPPT control increases the PV generated energy by 16.3% compared to the conventional system. Furthermore, the authors clarified that the proposed method has an extremely high UUF (useful utilization factor) of 98.7%. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 157(2): 65– 71, 2006; Published online in Wiley InterScience ( www.interscience. wiley.com ). DOI 10.1002/eej.20424  相似文献   

10.
    
Hybridization of energy sources provides better reliability and flexibility for the power generation system. To integrate different sources, a suitable power electronic interface and a power management strategy are mandatory requirements. In this paper, two types of dual‐input–single‐output DC–DC converters to integrate two different V‐I characteristic sources for DC microgrid application are presented. The analysis of the converters based on the voltage and current stress of the power switches available in the circuit has been carried out for the appropriate selection of power switches. The software simulation of the proposed converters is performed on a MATLAB/Simulink platform in a detailed manner, and an experimental prototype of the presented converters has been built to validate the simulation results. The experimental results are well matched with the simulation results, which demonstrate the efficient performance of the converters. © 2018 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.  相似文献   

11.
    
Exact and approximate sampled‐data models in closed forms are derived for switching DC–DC converters under peak/valley current‐mode control. The corresponding sampled‐data poles and zeros in closed forms are also derived. The location and stability conditions of the poles and zeros, boundary conditions of subharmonic instability, and nulling of the audio‐susceptibility are also derived. It is proved that the stable operating range of the source voltage is linearly proportional to the ramp slope. The sampled‐data models agree with previous experiment results and accurately predict the subharmonic instability. The different view from the sampled‐data model about the number and stability (minimum phase) of pole and zero does not necessarily invalidate the traditional continuous‐time averaged model. However, this different view gives better prediction about converter dynamics and is useful for the analog or digital controller design for DC–DC converters. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

12.
    
The dual active bridge (DAB)‐based isolated bidirectional converter has been used to realize bidirectional energy flow while offering needed isolation between the primary and secondary side: for example, the battery side and grid side of one plug‐in hybrid electric vehicle (PHEV). Even though the operation of a DAB‐based DC–DC converter is straightforward, various transient processes exist, such as the dead‐band effect, which deeply affects the dynamic performance of the converter in real world applications. Compensation of this effect is not easy because of the strong nonlinearity of the entire system. This paper quantitatively analyzed the dead‐band effect at different output powers, and presented a model‐based controller to realize the nonlinear dead‐band compensation strategy, which can effectively mitigate demerits of the traditional PI‐based control strategy. The proposed control algorithm is validated through theoretical simulation and experimental results. © 2011 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.  相似文献   

13.
    
Several new topologies of single‐switch non‐isolated DC–DC converters with wide conversion gain and reduced semiconductor voltage stress are proposed in this paper. Most of the proposed topologies are derived from the conventional inverse of SEPIC (Zeta) converter. The proposed topologies can operate with larger switch duty cycles compared with the existing single switch topologies, hence, making them well suitable for high step‐down voltage conversion applications. With extended duty cycle, the current stress in the active power switch is reduced, leading to a significant improvement of the system losses. Moreover, the active power switch in some of the proposed topologies is utilized much better compared to the conventional Zeta and quadratic‐buck converters. The principle of operation, theoretical analysis, and comparison of circuit performances with other step‐down converters are discussed regarding voltage and current stress and switch silicon utilization. Finally, simulation and experimental results for a design example of a 50 W/5 V at 42‐V input voltage operating at 50 kHz will be provided to evaluate the performance of the proposed converters. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

14.
    
A generalized model of the dynamics (GMD) of DC‐DC power electronic converters (PECs) is discussed in this paper. It is a geometrical piecewise‐affine continuous‐time model. The general idea of the GMD is to determine the local dynamic behavior of trajectories on the faces of the PEC commutation structure, which is a geometrical model of its commutation. This allows us to establish the direction of PEC dynamics on these faces. It can be either ‘entering’ into specific regions in state space or ‘exiting’ from them. Therefore, the local PEC dynamics can be treated as logical (two‐state). In practice, the GMD can be used for the analysis of PEC practical stability, which is a completely different concept from the concept of PEC stability in the classical Lyapunov sense. An outline of the design‐oriented approach to PEC practical stability analysis, which is based on the GMD, has also been presented. As illustrative examples, the GMD of a boost converter under peak current‐mode control and its application are presented. These examples show that the Lyapunov stability of a given PEC does not imply its practical stability, and that the results of PEC Lyapunov stability analysis and practical stability analysis are complementary to each other. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

15.
    
The PV array has a unique operating point that can supply maximum power to the load. This point is called the maximum‐power point (MPP), and is located on the output characteristics of the array. The locus of this point varies, non‐linearly, with the unpredictable variations in the solar insolation and/or the cell temperature. Thus, to operate the PV array at its MPPs for every instant, the PV system must contain a maximum‐power point tracking (MPPT) controller. This article proposes the application of the fuzzy logic controller (FLC) to operate a suggested PV control system at the MPP of the array for every instant. The simulation of the system indicates that the use of the FLC gives good results for the MPPT. Copyright © 2002 John Wiley & Sons, Ltd.  相似文献   

16.
    
Conventional matrix converters have a limited voltage gain less than 0.866 and also require many power switches and additional input filter that ensures a low input current harmonics to the grid. Quasi‐Z source (qZS) indirect matrix converter can provide high voltage gain and ensure a sinusoidal input current without additional input filter, which requires 12 power switches in rectifier stage. In this paper, a simplified qZS indirect matrix converter is proposed to overcome aforementioned limitations and achieve (1) higher voltage gain than 0.866, (2) less power switches, and (3) LC‐filter function integrated in qZS network to avoid additional filter. The new converter's operating principle and equivalent circuits are analyzed, and the modulation method is presented. The input current closed‐loop control is employed to implement sinusoidal input current waveform even though the proposed converter has less power switches and without extra input filter. A test bench is used to verify the simplified qZS indirect matrix converter and control methods. Simulation and experimental results identically validate the proposed converter system with wide voltage gain range and low input current harmonics. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

17.
    
This paper proposed a novel high step‐up converter with double boost paths. The circuit uses two switches and one double‐path voltage multiplier cell to own the double boost and interleaved effects simultaneously. The voltage gain ratio of the proposed DC‐DC converter can be three times the ratio of the conventional boost converter such that the voltage stress of the switch can be lower. The high step‐up performance is in accordance with only one double‐path voltage multiplier cell. Therefore, the number of diodes and capacitors in the proposed converter can be reduced. Furthermore, the interleaved property of the proposed circuit can reduce the losses in the rectifier diode and capacitor. The prototype circuit with 24‐V input voltage, 250‐V output voltage, and 150‐W output power is experimentally realized to verify the validity and effectiveness of the proposed converter. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

18.
    
The frequency‐domain‐based realization condition related to a novel non‐invasive chaos control is presented in this paper. According to the common piecewise‐linear characteristics of PWM‐controlled DC–DC converter system, a general expression for its Jacobian matrix is derived for optimizing the control parameters of the proposed non‐invasive chaos control. The relevant simulation and experiment results about the application of the chaos control to a voltage‐mode Buck converter are given, which confirm the feasibility of the parameter‐optimization method and the validity of the proposed non‐invasive chaos control. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

19.
    
A switch‐mode boost DC–DC converter has been developed to compensate for the IR‐drop because of the finite resistance of a charging cable. The boost ratio of the DC–DC converter is adaptively controlled by an IR‐drop sensing circuit to provide the required voltage level to a battery charger regardless of the cable resistance. Implemented in a 0.18 µm BCDMOS process, the IR‐drop compensating switch‐mode boost DC–DC converter occupies 6.2 mm2 active area and shows the 93.2% peak efficiency. The proposed IR‐drop compensating boost converter can be applied to compensate for the IR‐drop of any type of charging cables. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

20.
    
A new type of three‐phase quasi‐Z‐source indirect matrix converter (QZS‐IMC) is proposed in this paper. It uses a unique impedance network for achieving voltage‐boost capability and making the input current in continuous conduction mode (CCM) to eliminate the input filter. The complete modulation strategy is proposed to operate the QZS‐IMC. Meanwhile, a closed‐loop DC‐link peak voltage control strategy is proposed, and the DC‐link peak voltage is estimated by measuring both the input and capacitor voltages. With this proposed technique, a high‐performance output voltage control can be achieved with an excellent transient performance even if there are input voltage and load current variations. The controller is designed by using the small‐signal model. Vector control scheme of the induction motor is combined with the QZS‐IMC to achieve the motor drive. A QZS‐IMC prototype is built in laboratory, and experimental results verify the operating principle and theoretical analysis of the proposed converter. The simulation tests of QZS‐IMC based inductor motor drive are carried out to validate the proposed converter's application in motor drive. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号