超音速喷涂技术及其应用

回顾了超音速喷涂技术的发展过程;总结了超音速火焰喷涂、超音速等离子喷涂、超音速电弧喷涂及冷喷涂等设备的结构和技术特点;介绍了超音速喷涂工艺及涂层特性;展望了该技术在制备纳米涂层方面的应用及发展前景。     

微束等离子喷涂制备羟基磷灰石涂层微观结构的特征研究

目的 通过与大气等离子喷涂和超音速火焰啧涂的对比,研究微束等离子喷涂制备的羟基磷灰石涂层的微观组织特点.方法 以高结晶度的羟基磷灰石粉末为原料,采用三种不同的喷涂方法(微束等离子喷涂、大气等离子喷涂和超音速火焰喷涂),在Ti-6Al-4V基体上制备羟基磷灰石(HA)涂层.利用冷场发射扫描电子显微镜和X射线衍射仪,对三种涂层的形貌、相组成和择优取向进行分析.结果 与大气等离子喷涂及超音速火焰喷涂制备的涂层相比,应用该设备制备的羟基磷灰石涂层表面平整致密,无大量的气孔存在;涂层截面呈典型的层状结构,在近三分之一表面处观察到柱状晶;涂层中仅有少量的非晶相及分解相,结晶度高达90％以上.这些特征均有利于羟基磷灰石涂层在体液环境中的稳定性.结论 比较三种喷涂方法,采用微束等离子喷涂制备的羟基磷灰石涂层致密,结晶度高,杂相少,且存在择优取向的柱状晶.     

超音速等离子制备多元铝青铜合金涂层的组织

采用超音速等离子喷涂技术将新型多元铝青铜合金粉体喷涂在45号钢基体表面。运用XRD、SEM、EDS、EPMA等手段分析了涂层的组织特点及元素分布情况。结果表明,超音速等离子喷涂层主要由Cu9Al4、AlFe3、AlFe等相组成;涂层元素分布均匀;超音速等离子喷涂层硬度高于传统等离子喷焊层;涂层的结合强度为59.3MPa。可见,经过工艺参数的优化,超音速等离子喷涂可以制备出类似于多元铝青铜合金的易氧化涂层。     

高效能超音速等离子喷涂系统的研制

研制的HEPJet高效能超音速等离子喷涂系统，最大功率80kW，最大工作气体流量6m^3／h，可以喷涂金属粉末、碳化物陶瓷粉末和氧化物陶瓷粉末。单阳极内送粉结构的高效能超音速等离子喷枪，为国内外研究超音速等离子喷涂技术开创了一条新路。80kW级20kH脉宽调制IGBT逆变电源解决了输出电压高、输出电流大、高频干扰强等一系列难题，工作可靠。在保证涂层的结合强度、孔隙率等性能指标的前提下，喷涂成本比国外产品降低一半以上。     

超音速等离子喷涂制备WC-12Co涂层的性能特点

超音速等离子喷涂由于喷射粒子的飞行速度(400～500m/s)相对于普通等离子喷涂(＜200m/s)有了大幅提高,所制备的WC-12Co涂层具有更高的显微硬度和结合强度.用SEM和XRD分析了两种不同等离子喷涂工艺获得的涂层的相结构和显微组织,结果表明超音速等离子喷涂WC-12Co涂层综合性能要优于普通等离子喷涂.     

高效能超音速等离子喷涂NiCr-Cr3C2涂层性能研究

采用自行研制的高效能超音速等离子喷涂系统(HEPJet)制备了NiCr-Cr3C2涂层,并对涂层性能进行测试.结果表明,喷涂粒子速度高达460 m/s,实现了低功率、小气体流量获得超音速涂层的目的;HEPJet制备的NiCr-Cr3C2涂层其结合强度为60 MPa,显微硬度为926 HV0.3,沉积效率为54％,其抗高温氧化性能是12CrMoV钢的17倍,其常规性能赶超JP5000制备的NiCr-Cr3C2涂层.涂层表面的Cr2O3氧化膜与碳化物硬质相组成连续、致密而均匀的保护层是NiCr-Cr3C2涂层抗高温氧化性好的主要原因.     

基于响应曲面的Ar气氛超音速等离子喷涂钛涂层

采用超音速等离子喷涂可低成本、高效率制备钛涂层。采用响应曲面法（RSM）中的Box-Behnken（BBD）设计分析了Ar流量、功率、喷涂距离3个因素与超音速等离子射流中钛粒子飞行速度和温度的交互性,利用SEM和显微硬度计研究了钛涂层的微观结构和显微硬度。结果表明：建立的线性模型可靠,喷涂距离对粒子飞行速度和温度影响最大,且随喷涂距离增加粒子飞行速度减小温度增加,而Ar流量和功率对粒子飞行速度和温度的影响与喷涂距离相反。超音速等离子喷涂制备出的钛涂层硬度较低,且呈多孔结构,随粒子飞行速度增加孔隙率降低。     

等离子喷涂W-TiC涂层的组织和性能研究

分别采用普通大气等离子喷涂和超音速大气等离子喷涂技术在低活化钢表面制备了添加1.5%TiC(质量分数)的钨基涂层。研究了涂层的组织和密度、氧含量、孔隙率和热导率等物理性能。结果表明,用两种工艺制备的涂层中,TiC主要分布于钨片层之间和未熔钨颗粒周围,对片层和颗粒起连接作用;与采用普通大气等离子喷涂制备的涂层相比,超音速大气等离子喷涂的W-TiC涂层的组织更加致密,氧含量降低了0.1%,孔隙率下降近一半,热导率提高至119.6 W/(mK)。     

等离子喷涂与超音速火焰喷涂NiCr-Cr3C2涂层组织与摩擦磨损性能研究

目的 研究等离子喷涂与超音速火焰喷涂NiCr-Cr3C2涂层的组织、力学性能和摩擦磨损性能。方法 采用等离子喷涂与超音速火焰喷涂工艺制备NiCr-Cr3C2涂层,并采用X射线衍射仪（XRD）、扫描电镜（SEM）、万能试验机、显微硬度计和高速往复摩擦磨损试验机,系统地分析了两种工艺所得涂层的物相、组织、结合强度、硬度及摩擦磨损性能。结果 两种工艺制备的NiCr-Cr3C2涂层与基体界面结合效果良好。等离子喷涂NiCr-Cr3C2涂层为层片状组织,层间可见微裂纹,孔隙率较高;超音速火焰喷涂NiCr-Cr3C2涂层组织均匀,无明显微裂纹,可见少量微小孔隙。物相分析表明,等离子喷涂涂层由NiCr、Cr3C2和Cr7C3相组成,而超音速火焰喷涂涂层由NiCr和Cr3C2相组成。超音速火焰喷涂NiCr-Cr3C2涂层的耐磨性优于等离子喷涂涂层,等离子喷涂涂层和超音速火焰喷涂涂层的稳态摩擦系数分别为0.4和0.6。随载荷升高,两种工艺制备的NiCr-Cr3C2涂层摩擦系数均显著下降。磨损后,等离子喷涂NiCr-Cr3C2涂层表面具有明显的凹痕和剥落,而超音速火焰喷涂NiCr-Cr3C2涂层磨痕表面较光滑,未见明显剥落。两种工艺制备的涂层磨损机制均为磨粒磨损和疲劳磨损。结论 超音速火焰喷涂NiCr-Cr3C2涂层较等离子喷涂涂层组织更为致密,具有更为优良的综合力学性能和耐磨性,等离子喷涂制备的NiCr-Cr3C2涂层的减摩性较好。     

1Cr9MoVNbN叶片WC-Co防护涂层结构与性能研究

采用等离子喷涂和超音速火焰喷涂工艺在汽轮机动叶片1COMoVNbN母材上制备了WC-Co防护涂层。利用X射线衍射仪、扫描电子显微镜和高温冲蚀试验机等技术研究了涂层的相结构、表面形貌、孔隙率以及抗高温氧化和抗固体微粒侵蚀性能。结果表明,超音速火焰喷涂相比于等离子喷涂所制备的涂层中,WC相含量较多,涂层致密,孔隙率小。超音速火焰喷涂制备的含17%Co的WC-Co涂层相比于母材具有较好的抗高温氧化和抗固体微粒侵蚀性能。     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

Thermodynamics Study on the Decomposition of Chromite with KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

Influence of Heat Treatment on Damping Behaviour of the Magnesium Wrought Alloy AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.     

Directional Growth of Tin Crystals Controlled by Combined Solute Concentration Gradient Field and Static Magnetic Field

A new method was introduced to achieve directional growth of Sn crystals. Microstructures in liquid(Pb)/liquid(Sn) diffusion couples were investigated under various static magnetic fields. Results show that the β-Sn crystals mainly reveal an irregular dendritic morphology without or with a relatively low static magnetic field(B0.3 T). When the magnetic field is increased to 0.5 T, the β-Sn dendrites close to the final stage of growth begin to show some directional character. With a further increase in the magnetic field to a higher level(0.8–5 T), the β-Sn dendrites have an enhanced directional growth character, but the dendrites show a certain deflection. As the magnetic field is increased to 12 T, the directional growth of the β-Sn dendrites in the center of the couple is severely destroyed. The mechanism of the directional growth of the β-Sn crystals and the deflection of the β-Sn crystals with the application of static magnetic field was tentatively discussed.     

电化学噪声数据处理方法概述

综述了常见的电化学噪声数据处理方法,介绍了直流趋势剔除、统计分析、快速傅立叶变换(FFT)法计算功率谱密度(PSD)以及小波变换处理电化学噪声信号的基本过程,并阐释了各种数学处理及所得参数的物理意义。