New Insights into Alterations in PL Proteins Affecting Their Binding to DNA after Exposure of Mytilus galloprovincialis to Mercury—A Possible Risk to Sperm Chromatin Structure?

Mercury (Hg) is a highly toxic and widespread pollutant. We previously reported that the exposure of Mytilus galloprovincialis for 24 h to doses of HgCl₂ similar to those found in seawater (range 1–100 pM) produced alterations in the properties of protamine-like (PL) proteins that rendered them unable to bind and protect DNA from oxidative damage. In the present work, to deepen our studies, we analyzed PL proteins by turbidimetry and fluorescence spectroscopy and performed salt-induced release analyses of these proteins from sperm nuclei after the exposure of mussels to HgCl2 at the same doses. Turbidity assays indicated that mercury, at these doses, induced PL protein aggregates, whereas fluorescence spectroscopy measurements showed mercury-induced conformational changes. Indeed, the mobility of the PLII band changed in sodium dodecyl sulphate-polyacrylamide gel electrophoresis, particularly after exposure to 10-pM HgCl₂, confirming the mercury-induced structural rearrangement. Finally, exposure to HgCl₂ at all doses produced alterations in PL-DNA binding, detectable by DNA absorption spectra after the PL protein addition and by a decreased release of PLII and PLIII from the sperm nuclei. In conclusion, in this paper, we reported Hg-induced PL protein alterations that could adversely affect mussel reproductive activity, providing an insight into the molecular mechanism of Hg-related infertility.     

Mercury Chloride but Not Lead Acetate Causes Apoptotic Cell Death in Human Lung Fibroblast MRC5 Cells via Regulation of Cell Cycle Progression

Heavy metals are important for various biological systems, but, in excess, they pose a serious risk to human health. Heavy metals are commonly used in consumer and industrial products. Despite the increasing evidence on the adverse effects of heavy metals, the detailed mechanisms underlying their action on lung cancer progression are still poorly understood. In the present study, we investigated whether heavy metals (mercury chloride and lead acetate) affect cell viability, cell cycle, and apoptotic cell death in human lung fibroblast MRC5 cells. The results showed that mercury chloride arrested the sub-G₁ and G₂/M phases by inducing cyclin B1 expression. In addition, the exposure to mercury chloride increased apoptosis through the activation of caspase-3. However, lead had no cytotoxic effects on human lung fibroblast MRC5 cells at low concentration. These findings demonstrated that mercury chloride affects the cytotoxicity of MRC5 cells by increasing cell cycle progression and apoptotic cell death.     

Textural and Thermal Properties of the Novel Fucoidan/Nano-Oxides Hybrid Materials with Cosmetic,Pharmaceutical and Environmental Potential

The main purpose of the research was to obtain and study hybrid materials based on three different nano-oxides commonly used in the cosmetic and pharmaceutical industries: Al₂O₃, TiO₂, and ZnO, with the natural bioactive polysaccharide fucoidan. Since the mentioned oxides are largely utilized by industry, there is no doubt that the presented studies are important from an environmental point of view. On the basis of the textural studies (dynamic light scattering DLS, low temperature nitrogen adsorption, X-ray diffraction analysis XRD, scanning electron microscopy SEM) it was proved that the properties of the hybrid materials differ from the pure components of the system. Moreover, the advanced thermal analysis (TG-DTG-DSC) combined with the evolved gas analysis using Fourier transformed infrared spectroscopy (FTIR) and mass spectrometry were applied to describe the thermal decomposition of fucoidan, oxides and hybrid materials. It was found that the interactions between the polymer and the oxides results in the formation of the hybrid materials due to the functionalization of the nanoparticles surface, and that their thermal stability increased when compared to the pure substrates. Such findings definitely fill the literature void regarding the fucoidan based hybrid materials and help the industrial formulators in the preparation of new products.     

Propylene-ethylene Copolymer Filled Nanocomposites: Influence of Zn-ion Coating upon Nano-SiO2 on Structural,Thermal, and Dynamic Mechanical Properties

Propylene-ethylene copolymer (EP) nanocomposites based on nano-SiO₂ with and without Zn-ion coating were developed by conventional melt blending technique in a sigma internal mixer. Two composites each with 2.5 wt% filler were developed. The first composite was made by melt blending EP with nano-SiO₂ in a co-rotating sigma internal mixer. The second one was obtained by melt blending the same EP, but with Zn-ion coated nano-SiO₂. In case of Zn-ion coated nano-SiO₂ filled EP, wide-angle X-ray diffraction study (WAXD) showed a decrease in interplanar distance and lamellar polymer crystal size when compared to nano-SiO₂ filled EP. Differential scanning calorimetric (DSC) results showed Zn-ion coated nano-SiO₂ acting more as an effective nucleating agent than that of the nano-SiO₂. Thermogravimetric analysis (TGA) results showed improved thermal stability for EP in the presence of both the nanofillers. However, the thermal stability of Zn-ion coated nano-SiO₂ filled EP is higher than that of the nano-SiO₂ filled EP. Scanning electron microscope (SEM) study reveals that the Zn-ion coated nano-SiO₂ homogeneously distributed in the matrix, whereas nano-SiO₂ forms chainlike aggregates in the matrix phase. Dynamic mechanical analysis (DMA) study indicates that both the fillers increase storage modulus, E′; this increment is more prominent in nano-SiO₂ filled EP due to the formation of chain-type aggregates of nano-SiO₂.     

Properties of sol-gel SnO2/TiO2 electrodes and their photoelectrocatalytic activities under UV and visible light illumination

A visible light active binary SnO₂-TiO₂ composite was successfully prepared by a sol-gel method and deposited on Ti sheet as a photoanode to degrade orange II dye. Titanium and SnO₂ can promote the development of rutile phase of TiO₂ and inhibit the formation of anatase phase of TiO₂. Formation of SnO₂ crystalline is insignificant even when the calcination temperature increases to 700 °C. Heterogenized interface between SnO₂ and TiO₂ inhibits growth of TiO₂ linkage and leads to the particle-filled surface morphology of SnO₂-containing films. The carbonaceous, Ti-O-C bonds and Ti³⁺ species are likely to account for the photoabsorption and photoelectrocatalytic (PEC) activity under visible light illumination. The electrode with 30% SnO₂ exhibits higher photocurrent when compared with those in the region of 0-50%. The 600 °C-calcined SnO₂-TiO₂ electrode indicates higher activity when compared with those at 400, 500, 700 and 800 °C. PEC degradation of orange II follows the Langmuir-Hinshelwood model and takes place much effectively in a solution of pH 3.0 than those in pH 7.0 and pH 11.0.     

Catalytic Properties of Cr2O3 Doped with MgO Supported on MgF2 and Al2O3

Catalytic properties of Cr₂O₃ supported on MgF₂ or Al₂O₃ have been modified by magnesium oxide. The catalysts have been obtained by the co-impregnation method and characterised by: BET, XRD and TPR. As follows from the results, the oxides supported on magnesium fluorine react with each other already at 400 °C, leading to formation of an amorphous spinel-like phase. On the Al₂O₃ support such an MgCr₂O₄ spinel has appeared at much higher temperatures. The addition of magnesium oxide has a significant effect on the activity and selectivity of the catalysts studied in the CO oxidation reaction at room temperature and in the reaction of cyclohexane dehydrogenation. The magnesium–chromium catalysts supported on MgF₂ have been found to show much higher activity and selectivity than the analogous systems supported on Al₂O₃.     

Retention of Mechanical and Thermal Properties of Hydrothermal Aged Glass Fiber-Reinforced Polymer Nanocomposites

The combined effect of nano-Al₂O₃ and TiO₂ fillers on residual mechanical and thermal properties of glass fiber-reinforced polymer composites has been evaluated. The results reveal that the addition of 0.1?wt% of Al₂O₃ and 0.1?wt% of TiO₂ into the epoxy matrix reduces the water diffusivity by 12%. The residual flexural and interlaminar shear strength of the nanocomposite have been increased by 19 and 21%, respectively, as compared to those of neat epoxy glass fiber-reinforced polymer composite. In spite of reduction in water diffusivity and increase in strength, there was no improvement in glass transition temperature of the nanocomposites.     

Properties and rapid consolidation of nanostructured Al2O3-Al2SiO5 composites by high frequency induction heated sintering

The rapid sintering of nanostructured Al₂O₃ and Al₂O₃ to Al₂SiO₅ composites was investigated by a high-frequency induction heating sintering process. The advantage of this process is that it allows very quick densification to near theoretical density and inhibition of grain growth. Highly dense nanostructured Al₂O₃ and Al₂O₃ to Al₂SiO₅ composites were produced with simultaneous application of a 80 MPa pressure and induced output current of a total power capacity (15 kW) within 3 min. The sintering behavior, grain size and mechanical properties of Al₂O₃ and Al₂O₃ to Al₂SiO₅ composites were investigated.     

Synthesis of ternary zinc spinel oxides and their application in the photodegradation of organic pollutant

Ternary zinc spinel oxides such as Zn₂SnO₄, ZnAl₂O₄ and ZnFe₂O₄ were synthesized and characterized, and their activities in the photodegradation of phenol molecules were investigated. Zn₂SnO₄, ZnAl₂O₄ and ZnFe₂O₄ powders were synthesized by hydrothermal, metal–chitosan complexation and solvothermal routes, respectively. The face-centered cubic spinel structure of each material was confirmed by powder X-ray diffractometry (XRD) and its porous structure by N₂ adsorption–desorption isotherms. The characterization of spinels was complemented with Fourier transform infrared spectroscopy (FTIR) and X-rays fluorescence (XRF), revealing the formation of spinel structures with high purity. The photocatalytic activity in the degradation of phenol was observed only with Zn₂SnO₄ oxide. Mineralization degree of phenol molecules by Zn₂SnO₄ photocatalyst determined by total organic carbon analysis (TOC) reached 80% at 360 min under sunlight.     

Effect of Sizes of Nano Ca3(PO4)2 on Mechanical and Thermal Properties of Polyurethane Foam Composites

Particular sizes of nano inorganic filler, Ca₃(PO₄)₂ were prepared by following the matrix mediated growth technique. Composite foams were prepared on addition of different concentration (0.5–2.5 wt.%) of nano size filler in a single–phase polyurethane matrix. The differential Scanning Calorimetry (DSC) for composite as well as pure polyurethane was done to ascertain the degree of interaction of filler with the structure of the matrix as active sites. The degree of cell formation increases on increase in amount of reduced size nano filler in the composites where as decrease in case of larger size filler in composites. The increment in specific gravity from 0.17–0.25 for reduced nano size filler and 0.17–0.18 in case of larger size filler makes a strong support for the increment of cell numbers. The significant enhancement 250% in compressive strength, and the reduction of cell sizes shown in optical photographs satisfies the reasons of increment in heat of fusion (ΔH) in DSC. The decrement in (ΔH) cal/g in case of larger size filler for curing shows the conduction of heat is more due formation of cells less in numbers results in reduction of rate of heating more. Thermal gravimetric analysis (TGA) was done to know the degradation behavior. The TGA results, shows increment in onset temperature and mid temperature of the first step degradation in case of larger size nano filler. Decrement of flammability from 0.47–13.14 sec/mm for reduced nano size filler and 0.47–8.23 sec/mm in case of larger size filler, show that the incorporation of nano particles not only improves the mechanical properties but also retards the flammability.     

The catalytic performance in oxidative coupling of methane and the surface basicity of La2O3, Nd2O3, ZrO2 and Nb2O5

The catalytic performance in oxidative coupling of methane (OCM) of unmodified pure La₂O₃, Nd₂O₃, ZrO₂ and Nb₂O₅ has been investigated under various conditions. The results confirmed that the activity of La₂O₃ and Nd₂O₃ was always much higher than that of the remaining two. The surface basicity/base strength distribution of pure La₂O₃, Nd₂O₃, ZrO₂ and Nb₂O₅ was measured using a test reaction of transformation of 2-butanol and a temperature-programmed desorption of CO₂. Both methods showed that La₂O₃ and Nd₂O₃ had high basicity and contained medium and strong basic sites (lanthanum oxide more and neodymium oxide somewhat less). ZrO₂ had only negligible amount of weak basic sites and Nb₂O₅ was rather acidic. The confrontation of the basicity and catalytic performance indicated that in the case of investigated oxides, the basicity (especially strong basic sites) could be a decisive factor in determination of the catalytic activity in OCM. Only in the case of ZrO₂ it was observed a moderate catalytic performance in spite of negligible basicity. The influence of a gas atmosphere used in the calcination of oxides (flowing oxygen, helium and nitrogen) on their basicity and catalytic activity in OCM had been also investigated. Contrary to earlier observations with MgO, no effect of calcination atmosphere on the catalytic performance of investigated oxides in OCM and on their basicity was observed.     

A green method for solvent-free conversion of epoxides to thiiranes using NH4SCN in the presence of NiFe2O4 and MgFe2O4 magnetic nanocatalysts

Nickel and magnesium ferrite magnetic nanoparticles were fabricated and applied as efficient and reusable catalysts in the solvent-free conversion of various epoxides to the corresponding thiiranes with ammonium thiocyanate under oil bath (60°C) conditions. NiFe₂O₄ and MgFe₂O₄ nanoparticles can catalyze the reactions at short times in high to excellent yields. The catalysts can also be recovered easily using an external magnetic field and be reused four times without any significant loss of activity.     

Role of vanadium sites in NO and O2 adsorption processes over VOx/CeO2-ZrO2 catalysts – EPR and IR studies

The interaction of NO and O₂ with 5 mol.% of vanadia deposited on Ce_0.10Zr_0.90O₂ and Ce_0.69Zr_0.31O₂ supports by wet impregnation was studied by means of EPR and IR. The supports were structurally characterized by XRD and Raman spectroscopy. Influence of the phase composition of the support on vanadium speciation as well as on surface architecture of the oxovanadium entities was discussed. The NO forms adsorbed on vanadium-containing systems were compared to those observed on bare CeO₂-ZrO₂ supports. The main products appearing on the catalysts surface during the consecutive reaction with NO and O₂ were identified and their thermal evolution was observed. Changes in vanadium speciation accompanying redox processes related to NO and O₂ activation were also observed and discussed.     

Preparation and electrochemical studies of metal–carbon composite catalysts for small-scale electrosynthesis of H2O2

Numerous transition metal–carbon composite catalysts (M = V, Zn, Ni, Sn, Ce, Ba, Fe, Cu) have been synthesized and tested for electroreduction of O₂ to H₂O₂, The activity and selectivity of all synthesized catalysts for electrosynthesis of H₂O₂ were determined by the rotating ring-disk electrode method in acidic and neutral electrolytes. The Co-based catalysts in general showed the highest activity towards H₂O₂ formation. Experiments with different loading contents of Co showed that the activation overpotential losses of oxygen reduction to H₂O₂ reduces as loading increases to about 4 wt% Co. Addition of Co beyond this level did not seem to impact the overpotential losses. The cobalt-based catalysts, were spray-coated onto 120 μm thick Toray^® graphite substrates, and were studied in bulk electrolysis cells for up to 100 h at potentiostatic conditions (0.25 V vs. RHE) in pH 0, 3, and 7 electrolytes. At (25 °C and 1 bar) with a catalysts loading of about and using dissolved O₂ in 0.5 M H₂SO₄, typical H₂O₂ electrosynthesis rates of about were reached with current efficiencies of about 85 ± 5% at 0.25 V (vs. RHE).     

Processing of alumina-coated tetragonal zirconia materials and their response to sliding wear

Alumina-coated tetragonal zirconia stabilised with 3 mol% of Y₂O₃ (YTZP) specimens (30 mm × 30 mm × 6 mm) have been obtained by dipping of pre-sintered YTZP compacts in alumina suspensions and subsequent sintering. The coated specimens present hardness values and a wear resistance similar to those of reference dense alumina specimens and significantly higher than those of the YTZP substrates.     

Reduction of lean NOx by ethanol over Ag/Al2O3 catalysts in the presence of H2O and SO2

The reduction of lean NOx using ethanol in simulated diesel engine exhaust was carried out over Ag/Al₂O₃ catalysts in the presence of H₂O and SO₂. The Ag/Al₂O₃ catalysts are highly active for the reduction of lean NOx by ethanol but the reaction is accompanied by side reactions to form CH₃CHO, CO along with small amounts of hydrocarbons (C₃H₆, C₂H₄, C₂H₂ and CH₄) and nitrogen compounds such as NH₃ and N₂O. The presence of H₂O enhances the NOx reduction while SO₂ suppresses the reduction. The presence of SO₂ along with H₂O suppresses the formation of acetaldehyde and NH₃. By infrared spectroscopy, it was revealed that the reactivity of NCO species formed in the course of the reaction was greatly enhanced in the presence of H₂O. The NCO species readily reacts with NO in the presence of O₂ and H₂O at room temperature, being converted to N₂ and CO₂ (CO). Addition of SO₂ suppresses the formation of NCO species and lowers the reactivity of the NCO species. However, the reduction of NOx is still kept at high conversion levels in the presence of H₂O and SO₂ over the present catalysts. About 80% of NOx in the simulated diesel engine exhaust was removed at 743 K. This revised version was published online in July 2006 with corrections to the Cover Date.     

Electric charge trapping, residual stresses and properties of ceramics after metal/ceramics bonding

The use of ceramic components in electrical engineering and mechanical applications is rapidly increasing. Most of these applications require the use of ceramics bonded with metal. In this paper, we have studied the role of residual stresses occurring after joining between an industrial alumina ceramic (Al₂O₃) and Ni-based super-alloy, on the dielectric behaviour of ceramics. The electric charging phenomenon i.e. trapping-detrapping or diffusion of electric charges is studied by Scanning Electron Microscope Mirror Effect (SEMME) coupled with the Induced Current Method (ICM). Knowing that localized trapped charges in ceramics is a source of damage, the correlation between residual stress intensity, apparent-toughness of ceramics and ability to trap charges near the interface was demonstrated: the SEMME and ICM measurements of the quantities of trapped charges near the interface, highlighted the changes in the ceramic properties related to residual stresses due to both thermo-mechanical effect and diffusion of metallic species in the ceramics, during the bonding process.     

Effect of TiO2 on phase evolution and microstructure of MgAl2O4 spinel in different atmospheres

The effect of TiO₂ on the formation and microstructure of magnesium aluminate spinel (MgAl₂O₄) at 1600 °C in air and reducing conditions were investigated. Under reducing conditions, stoichiometric MgAl₂O₄ spinel shifted toward alumina-rich types owing to volatilization of MgO, resulting in an increase in the porosity of fired samples. Addition of graphite to mixtures of MgO and Al₂O₃ intensified the reducing conditions and accelerated the formation of non-stoichiometric MgAl₂O₄. For TiO₂-containing samples on addition of MgAl₂O₄, magnesium aluminum titanium oxide (Mg_xAl_2(1−x)Ti_(1+x)O₅, x = 0.2 or 0.3) was detected as a minor phase. Under reducing conditions, XRD peak shifts were smaller for TiO₂-containing samples than for samples without TiO₂ owing to the formation of a solid solution of TiO₂ in MgAl₂O₄ and establishment of alumina-rich spinel, which have opposite effects on increasing the lattice parameter. In bauxite-containing samples, MgAl₂O₄ spinel, corundum, magnesium orthotitanate spinel (Mg₂TiO₄) and amorphous phases were identified. Mg₂TiO₄ spinel formed a complete solid solution with MgAl₂O₄ spinel but Mg₂TiO₄ remained as a distinct phase owing to the heterogeneous microstructure of bauxite-containing samples. Also dense microstructure established in air fired TiO₂ containing samples. The results are discussed with emphasis on the application and design of alumina-magnesia-carbon refractory materials, which are used in the steel industry.     

Accommodation of impurities in α-Al2O3, α-Cr2O3 and α-Fe2O3

Atomic scale computer simulation was used to predict the mechanisms and energies associated with the accommodation of aliovalent and isovalent dopants in three host oxides with the corundum structure. Here we consider a much more extensive range of dopant ions than has previously been the case. This enables a rigorous comparison of calculated mechanism energetics. From this we predict that divalent ions are charge compensated by oxygen vacancies and tetravalent ions by cation vacancies over the full range of dopant radii. When defect associations are included in the model these conclusions remain valid. At equilibrium, defects resulting from extrinsic dopant solution dominate intrinsic processes, except for the largest dopant cations. Solution reaction energies increase markedly with increasing dopant radius. The behaviour of cluster binding energies is more complex.     

Field assisted and flash sintering of alumina and its relationship to conductivity and MgO-doping

We show that flash-sintering in MgO-doped alumina is accompanied by a sharp increase in electrical conductivity. Experiments that measure conductivity in fully dense specimens, prepared by conventional sintering, prove that this is not a cause-and-effect relationship, but instead that the concomitant increase in the sintering rate and the conductivity share a common mechanism. The underlying mechanism, however, is mystifying since electrical conductivity is controlled by the transport of the fastest moving charged species, while sintering, which requires molecular transport or chemical diffusion, is limited by the slow moving charged species. Joule heating of the specimen during flash sintering cannot account for the anomalously high sintering rates. The sintering behavior of MgO-doped alumina is compared to that of nominally pure-alumina: the differences provide insight into the underlying mechanism for flash-sintering. We show that the pre-exponential in the Arrhenius equation for conductivity is enhanced in the non-linear regime, while the activation energy remains unchanged. The nucleation of Frenkel pairs is proposed as a mechanism to explain the coupling between flash-sintering and the non-linear increase in the conductivity.