The use of a mixed coupling agent system to improve the performance of polypropylene-based composites reinforced with short-glass-fibre mat

In order to improve the mechanical properties of composites consisting of polypropylene reinforced with mats of short glass fibres, the fibre surface was treated with a silane coupling agent, N-β(N-vinylbenzylaminoethyl)-γ-aminopropyl trimethoxy silane hydrogen chloride (STS), and a titanate coupling agent, isopropyltriisostearoyl titanate (TTS). The flexural properties and the impact absorption energy of these composites were measured as a function of coupling agent concentration. STS-only treatment of the fibre surface enhanced the flexural strength and the flexural modulus of the composite, while TTS-only treatment decreased the flexural strength and the flexural modulus. The improved flexural properties of the composite brought about by the STS-only treatment were obtained at the cost of its impact absorption energy, whereas TTS-only treatment showed the inverse characteristics. However, in a mixed coupling agent system, the impact absorption energy of the composite was improved without a reduction in the flexural properties. A morphological study of the fracture surfaces of the composite after impact testing, void content measurement and single-fibre fragmentation test were also carried out to understand the interfacial phenomena of the surface treated composites.     

Role of matrix modification on interlaminar shear strength of glass fibre/epoxy composites

Interlaminar shear properties of fibre reinforced polymer composites are important in many structural applications. Matrix modification is an effective way to improve the composite interlaminar shear properties. In this paper, diglycidyl ether of bisphenol-F/diethyl toluene diamine system is used as the starting epoxy matrix. Multi-walled carbon nanotubes (MWCNTs) and reactive aliphatic diluent named n-butyl glycidyl ether (BGE) are employed to modify the epoxy matrix. Unmodified and modified epoxy resins are used for fabricating glass fibre reinforced composites by a hot-press process. The interlaminar shear strength (ILSS) of the glass fibre reinforced composites is investigated and the results indicate that introduction of MWCNT and BGE obviously enhances the ILSS. In particular, the simultaneous addition of 0.5 wt.% MWCNTs and 10 phr BGE leads to the 25.4% increase in the ILSS for the glass fibre reinforced composite. The fracture surfaces of the fibre reinforced composites are examined by scanning electron microscopy and the micrographs are employed to explain the ILSS results.     

Mechanical property analysis of kenaf–glass fibre reinforced polymer composites using finite element analysis

Nowadays, natural fibres are used as a reinforcing material in polymer composites, owing to severe environmental concerns. Among many different types of natural resources, kenaf plants have been extensively exploited over the past few years. In this experimental study, partially eco-friendly hybrid composites were fabricated by using kenaf and glass fibres with two different fibre orientations of 0° and 90°. The mechanical properties such as tensile, flexural and impact strengths of these composites have been evaluated. From the experiment, it was observed that the composites with the 0° fibre orientation can withstand the maximum tensile strength of 49.27 MPa, flexural strength of 164.35 MPa, and impact strength of 6 J. Whereas, the composites with the 90° fibre orientation hold the maximum tensile strength of 69.86 MPa, flexural strength of 162.566 MPa and impact strength of 6.66 J. The finite element analysis was carried out to analyse the elastic behaviour of the composites and to predict the mechanical properties by using NX Nastran 9.0 software. The experimental results were compared with the predicted values and a high correlation between the results was observed. The morphology of the fractured surfaces of the composites was analysed using a scanning electron microscopy analysis. The results indicated that the properties were in the increasing trend and comparable with pure synthetic fibre reinforced composites, which shows the potential for hybridization of kenaf fibre with glass fibre.     

Polyoxymethylene composites with natural and cellulose fibres: Toughness and heat deflection temperature

Cellulose and abaca fibre reinforced polyoxymethylene (POM) composites were fabricated using an extrusion coating (double screw) compounding followed by injection moulding. The long cellulose or abaca fibres were dried online with an infrared dryer and impregnated fibre in matrix material by using a special extrusion die. The fibre loading in composites was 30 wt.%. The tensile properties, flexural properties, Charpy impact strength, falling weight impact strength, heat deflection temperature and dynamic mechanical properties were investigated for those composites. The fibre pull-outs, fibre matrix adhesion and cracks in composites were investigated by using scanning electron microscopy. It was observed that the tensile strength of composites was found to reduce by 18% for abaca fibre and increase by 90% for cellulose fibre in comparison to control POM. The flexural strength of composites was found to increase by 39% for abaca fibre and by 144% for cellulose fibre. Due to addition of abaca or cellulose fibre both modulus properties were found to increase 2-fold. The notched Charpy impact strength of cellulose fibre composites was 6-fold higher than that of control POM. The maximum impact resistance force was shorted out for cellulose fibre composites. The heat deflection temperature of abaca and cellulose fibre composites was observed to be 50 °C and 63 °C higher than for control POM respectively.     

Polypropylene composites with enzyme modified abaca fibre

Abaca fibre reinforced PP composites were prepared using a high speed mixer followed by injection moulding with 30 wt.% of fibre load. Prior to composite production, the fibres were modified by fungamix and natural enzyme. The effects of modification of the fibre were assessed on the basis of morphology and thermal resistance and as well as on mechanical, thermal and environmental stress corrosion resistance properties of the resulting composites. Coupling agent (MA-PP) was also used with unmodified abaca fibre to observe the coupling agent effect on resulting composites properties. The moisture absorption of the composites was found to be reduced 20–45% due to modification. Tensile strength found to be 5–45% and flexural strengths found to be 10–35% increased due to modification. Modified fibre composites found to better resistance in acid and base medium.     

The effect of reprocessing on the mechanical properties of polypropylene reinforced with wood pulp,flax or glass fibre

Composites of polypropylene, substitutable for a given application and reinforced with: Medium Density Fibreboard fibre (MDF) (40 wt%); flax (30 wt%); and glass fibre (20 wt%), were evaluated after 6 injection moulding and extrusion reprocessing cycles. Of the range of tensile, flexural and impact properties examined, MDF composites showed the best mean property retention after reprocessing (87%) compared to flax (72%) and glass (59%). After 1 reprocessing cycle the glass composite had higher tensile strength (56.2 MPa) compared to the MDF composite (44.4) but after 6 cycles the MDF was stronger (35.0 compared to 29.6 MPa for the glass composite). Property reductions were attributed to reduced fibre length. MDF fibres showed the lowest reduction in fibre length between 1 and 6 cycles (39%), compared to glass (51%) and flax (62%). Flax fibres showed greater increases in damage (cell wall dislocations) with reprocessing than was shown by MDF fibres.     

Development of kenaf-glass reinforced unsaturated polyester hybrid composite for structural applications

The main aim of this paper is to develop kenaf-glass (KG) fibres reinforced unsaturated polyester hybrid composite on a source of green composite using sheet moulding compound process. Unsaturated polyester resin (UPE) and KG fibres in mat form were used at a ratio of 70:30 (by volume) with treated and untreated kenaf fibre. The kenaf fibre was treated with 6% sodium hydroxide (NaOH) diluted solution for 3 h using mercerization method. The hybrid composites were tested for flexural, tensile and Izod impact strength using ASTM D790-03, ASTM D618 and ASTM D256-04 standards respectively. The highest flexural, tensile and impact strength were obtained from treated kenaf with 15/15 v/v KG fibres reinforced UPE hybrid composite in this investigation.Scanning electron microscopy fractography showed fibre cracking, debonding and fibre pulled-out as the main fracture mode of composites and kenaf treated 15/15 v/v KG reinforced hybrid composite exhibited better interfacial bonding between the matrix and reinforcement compared to other combinations.     

Effect of resin system on the mechanical properties and water absorption of kenaf fibre reinforced laminates

The objective of this study is to compare the mechanical and water absorption properties of kenaf (Hibiscus cannabinus L.) fibre reinforced laminates made of three different resin systems. The use of different resin systems is considered so that potentially complex and expensive fibre treatments are avoided. The resin systems used include a polyester, a vinyl ester and an epoxy. Laminates of 15%, 22.5% and 30% fibre volume fraction were manufactured by resin transfer moulding. The laminates were tested for strength and modulus under tensile and flexural loading. Additionally, tests were carried out on laminates to determine the impact energy, impact strength and water absorption. The results revealed that properties were affected in markedly different ways by the resin system and the fibre volume fraction. Polyester laminates showed good modulus and impact properties, epoxy laminates displayed good strength values and vinyl ester laminates exhibited good water absorption characteristics. Scanning electron microscope studies show that epoxy laminates fail by fibre fracture, polyester laminates by fibre pull-out and vinyl ester laminates by a combination of the two. A comparison between kenaf and glass laminates revealed that the specific tensile and flexural moduli of both laminates are comparable at the volume fraction of 15%. However, glass laminates have much better specific properties than the kenaf laminates at high fibre volume fractions for all three resins used.     

Flexural properties of hemp fibre reinforced polylactide and unsaturated polyester composites

In this work, flexural strength and flexural modulus of chemically treated random short and aligned long hemp fibre reinforced polylactide and unsaturated polyester composites were investigated over a range of fibre content (0-50 wt%). Flexural strength of the composites was found to decrease with increased fibre content; however, flexural modulus increased with increased fibre content. The reason for this decrease in flexural strength was found to be due to fibre defects (i.e. kinks) which could induce stress concentration points in the composites during flexural test, accordingly flexural strength decreased. Alkali and silane fibre treatments were found to improve flexural strength and flexural modulus which could be due to enhanced fibre/matrix adhesion.     

Tailoring of dual-interface in high tenacity PP composites – Toughening with positive hybrid effect

The study proves the feasibility of manufacturing injection moulded polypropylene composites reinforced with short rayon cellulose fibres of two selectively tailored fibre–matrix interfaces. The originally developed method relies on selective chemical grafting of two different polymer waxes onto the surface of cellulose fibres in order to obtain two different strengths of fibre–matrix interfaces in one composite. This selective tailoring of a dual-interface is meant to improve the notched impact strength without deteriorating of its flexural strength. Compatibilised fibres have a strong interphase, which conditions the transfer of strain from the matrix to fibres during deformation. Fibres tailored for a weak interface more efficiently hinder the crack propagation at crash. A 32% improvement of composite notched impact strength was achieved with merely a 5% deterioration of its flexural strength. Its specific properties are on the level or better than those of polypropylene counterpart reinforced with the same content of glass fibres.     

The effects of alkali–silane treatment on the tensile and flexural properties of short fibre non-woven kenaf reinforced polypropylene composites

Kenaf fibre reinforced polypropylene composites were manufactured by compression moulding. The kenaf fibre was considered in three forms; untreated, treated with sodium hydroxide solution and treated with sodium hydroxide solution followed by three-aminopropyltriethoxysilane. The effects of these chemical treatments on the tensile and flexural properties of the composites were investigated. Mechanical test results show that alkali treatment followed by three-aminopropyltriethoxysilane treatment (alkali–silane treatment) significantly improves the tensile and flexural properties of short fibre non-woven kenaf polypropylene composites. In particular, the specific tensile and flexural strengths of alkali–silane treated kenaf composites with 30% fibre mass fraction are, respectively, only 4% and 11% lower than those of composites made using glass fibre. Scanning electron microscopy examination shows that the improvements in the tensile and flexural properties resulting from alkali–silane treatment can be attributed to better bonding between the fibres and matrix.     

High performance hybrid PP and PLA biocomposites reinforced with short man-made cellulose fibres and softwood flour

This paper presents the research on hybrid thermoplastic biocomposites reinforced with a combination of short man-made cellulose fibres and softwood flour. The introduced short fibre composites are meant to be processed with injection moulding and may be an alternative to glass-fibre reinforced thermoplastics on account of their comparable specific strengths. The occurring positive hybrid effect enables to substitute up to half the weight of short fibre cellulose reinforcement with softwood flour without a significant reduction of material flexural strength. The flexural modulus of investigated hybrid biocomposites remained approximately at the same level, while impact strength was reduced with increasing softwood flour content. The proposed hybridisation leads to establishing biocomposites of suitable performance with competitive density, price and recycling possibilities in comparison to standard glass fibre reinforced counterparts. Moreover, the application of biobased polymers like polylactide as biocomposite matrix, contributes to the development of so called “green” high performance materials.     

The influence of fibre properties of the performance of glass-fibre-reinforced polyamide 6,6

We discuss the effect of fibre strength and diameter on the balance of mechanical properties of glass-reinforced polyamide 6,6. The results show that the elastic properties of injection-moulded short-glass-fibre-reinforced polyamide 6,6 are not strongly influenced by fibre diameter in the 10–17 micron range. The ultimate properties of these composites (strength and Izod impact behaviour) showed a clear dependence on fibre diameter and were increased by the presence of high-strength S-2 glass fibres. The relationship between the observed mechanical properties and the length, diameter and orientation of the fibres is explored. We have measured fibre length as a function of diameter in composites containing a single glass-reinforcement product and blends of two glass products. The reduction in glass-fibre length from glass-fibre production to final composite moulding has been followed step by step. The final composite mechanical properties, the fibre length, strength, diameter and orientation are all inter-related.     

Environmental advantage by choice: Ex-ante LCA for a new Kraft pulp fibre reinforced polypropylene composite in comparison to reference materials

This study analyses the circumstances of environmental advantage by benchmarking a novel Kraft pulp fibre reinforced polypropylene against its matrix material and two other composites with talcum and glass fibres. With one exception, all composites use less non-renewable energy (−1% to −29%), but only the Kraft pulp fibre reinforced polypropylene achieves a reduction in global warming potential (14% to 35%) considering different functional units compared to polypropylene. The comparisons on basis of function–strength and stiffness in this case study–show that the adequate application of specific material properties, are key to achieve environmental advantages.     

Layered silicates nanocomposite matrix for improved fiber reinforced composites properties

Three-phase glass fiber reinforced composites (GFRP) consisting of traditional woven glass fiber and polyamide-6 (PA6) matrix dispersed with organically modified layered silicates were prepared and investigated in this study. The fabrication of GFRP with different weight percentages of layered silicates was successful when the matrix contains less than 5 wt% of the layered silicates. The improvement due to the high aspect ratio and high stiffness of the layered silicates is illustrated through the matrix-controlled properties of the GFRP. The results showed that the GFRP with 5 wt% layered silicates offer the largest improvement of approximately 30% increase in both flexural strength and compressive strength at elevated temperatures. On the other hand, the in-plane shear properties measured from [±45]_s laminates revealed that the layered silicates help improved both the in-plane shear strength and modulus appropriately. By utilizing a nanocomposite matrix, improvement of stiffness and strength, as well as thermal and barrier properties is obtained without any change in processing temperature of the fiber composites.     

Effect of glass fiber hybridization on properties of sisal fiber–polypropylene composites

Natural fiber reinforced polymer composites became more attractive due to their light weight, high specific strength, and environmental concern. However, some limitations such as low modulus, poor moisture resistance were reported. This study aimed to investigate the effect of glass fiber hybridization on the physical properties of sisal–polypropylene composites. Polypropylene grafted with maleic anhydride (PP-g-MA) was used as a compatibilizer to enhance the compatibility between the fibers and polypropylene. Incorporating glass fiber into the sisal–polypropylene composites enhanced tensile, flexural, and impact strength without having significant effect on tensile and flexural moduli. In addition, adding glass fiber improved thermal properties and water resistance of the composites.     

Effects of alkali treatment and elevated temperature on the mechanical properties of bamboo fibre–polyester composites

Bamboo fibre reinforced composites are not fully utilised due to the limited understanding on their mechanical characteristics. In this paper, the effects of alkali treatment and elevated temperature on the mechanical properties of bamboo fibre reinforced polyester composites were investigated. Laminates were fabricated using untreated and sodium hydroxide (NaOH) treated (4–8% by weight) randomly oriented bamboo fibres and tested at room and elevated temperature (40, 80 and 120 °C). An improvement in the mechanical properties of the composites was achieved with treatment of the bamboo fibres. An NaOH concentration of 6% was found optimum and resulted in the best mechanical properties. The bending, tensile and compressive strength as well as the stiffness of this composite are 7, 10, 81, and 25%, respectively higher than the untreated composites. When tested up to 80 °C, the flexural and tensile strength are enhanced but the bending stiffness and compressive strength decreased as these latter properties are governed by the behaviour of resin. At 40 and 80 °C, the bond between the untreated fibres and polyester is comparable to that of treated fibres and polyester which resulted in almost same mechanical properties. However, a significant decrease in all mechanical properties was observed for composites tested at 120 °C.     

Hierarchical composites reinforced with robust short sisal fibre preforms utilising bacterial cellulose as binder

A novel robust non-woven sisal fibre preform was manufactured using a papermaking process utilising nanosized bacterial cellulose (BC) as binder for the sisal fibres. It was found that BC provides significant mechanical strength to the sisal fibre preforms. This can be attributed to the high stiffness and strength of the BC network. Truly green non-woven fibre preform reinforced hierarchical composites were prepared by infusing the fibre preforms with acrylated epoxidised soybean oil (AESO) using vacuum assisted resin infusion, followed by thermal curing. Both the tensile and flexural properties of the hierarchical composites showed significant improvements over polyAESO and neat sisal fibre preform reinforced polyAESO. These results were corroborated by the thermo-mechanical behaviour of the (hierarchical) composites, which showed an increased storage modulus and enhanced fibre–matrix stress transfer. Micromechanical modelling was also performed on the (hierarchical) composites. By using BC as binder for short sisal fibres, added benefits such as the high Young’s modulus of BC, enhanced fibre–fibre and fibre–matrix stress transfer can be utilised in the resulting hierarchical composites.     

Introducing cellulose nanocrystals in sheet molding compounds (SMC)

The mechanical properties of short glass fiber/epoxy composites containing cellulose nanocrystals (CNC) made using sheet molding compound (SMC) manufacturing method as well as the rheological and thermomechanical properties of the CNC-epoxy composites were investigated as a function of the CNC content. CNC up to 1.4 wt% were dispersed in the epoxy to produce the resin for SMC production. The addition of CNC in the resin increased its viscosity and slightly reduced the heat of reaction during the polymerization without altering the curing time and temperature and the effective pot life of the resin. The incorporation of 0.9 wt% CNC in the SMC composite resulted in increases in elastic modulus and tensile strength by ∼25% and ∼30% and in flexural modulus and strength by ∼44% and ∼33% respectively. Concentrations of CNC up to 0.9 wt% in the SMC composite did not alter the impact energy.     

The potential of harakeke fibre as reinforcement in polymer matrix composites including modelling of long harakeke fibre composite strength

Mechanical properties of aligned long harakeke fibre reinforced epoxy with different fibre contents were evaluated. Addition of fibre was found to enhance tensile properties of epoxy; tensile strength and Young’s modulus increased with increasing content of harakeke fibre up to 223 MPa at a fibre content of 55 wt% and 17 GPa at a fibre content of 63 wt%, respectively. The flexural strength and flexural modulus increased to a maximum of 223 MPa and 14 GPa, respectively, as the fibre content increased up to 49 wt% with no further increase with increased fibre content. The Rule of Mixtures based model for estimating tensile strength of aligned long fibre composites was also developed assuming composite failure occurred as a consequence of the fracture of the lowest failure strain fibres taking account porosity of composites. The model was shown to have good accuracy for predicting the strength of aligned long natural fibre composites.