Effect of pectin and hemicellulose removal from hemp fibres on the mechanical properties of unidirectional hemp/epoxy composites

The objective of this study was to investigate the effect of pectin and hemicellulose removal from hemp fibres on the mechanical properties of hemp fibre/epoxy composites. Pectin removal by EDTA and endo-polygalacturonase (EPG) removed epidermal and parenchyma cells from hemp fibres and improved fibre separation. Hemicellulose removal by NaOH further improved fibre surface cleanliness. Removal of epidermal and parenchyma cells combined with improved fibre separation decreased composite porosity factor. As a result, pectin removal increased composite stiffness and ultimate tensile strength (UTS). Hemicellulose removal increased composite stiffness, but decreased composite UTS due to removal of xyloglucans. In comparison of all fibre treatments, composites with 0.5% EDTA + 0.2% EPG treated fibres had the highest tensile strength of 327 MPa at fibre volume content of 50%. Composites with 0.5% EDTA + 0.2% EPG → 10% NaOH treated fibres had the highest stiffness of 43 GPa and the lowest porosity factor of 0.04.     

Fabrication and mechanical properties of well-dispersed multiwalled carbon nanotubes/epoxy composites

Multiwalled carbon nanotubes (MWCNTs)/epoxy nanocomposites were fabricated by using ultrasonication and the cast molding method. In this process, MWCNTs modified by mixed acids were well dispersed and highly loaded in an epoxy matrix. The effects of MWCNTs addition and surface modification on the mechanical performances and fracture morphologies of composites were investigated. It was found that the tensile strength improved with the increase of MWCNTs addition, and when the content of MWCNTs loading reached 8 wt.%, the tensile strength reached the highest value of 69.7 MPa. In addition, the fracture strain also enhanced distinctly, implying that MWCNTs loading not only elevated the tensile strength of the epoxy matrix, but also increased the fracture toughness. Nevertheless, the elastic modulus reduced with the increase of MWCNTs loading. The reasons for the mechanical property changes are discussed.     

Effect of water ageing on nanoindentation response of single hemp yarn/epoxy composites

This paper aims to evaluate the influence of water ageing on nanoindentation response of the in situ components of hemp/epoxy composites. Specific samples have been tested, made of single hemp yarn composites with two different epoxy resins. Analysis of indentation points depending on their location in the yarn microstructure has been performed. Measurements showed the influence of neighbouring fibres on the reduced modulus in the confined resin. Water induces a decrease in nanoindentation properties, and maximum decrease in reduced modulus takes place in the interfacial zone, which shows the significant degradation of the fibre/matrix interface caused by water ageing. Evolutions in the indentation properties induced by water are similar for both partially bio-based and fully synthetic epoxy resin composites. All these results bring insights into the influence of water ageing of each constituent of hemp fibre reinforced composites and give interesting data for developing eco-composite materials.     

Processing, compatibilization and properties of ternary composites of Mater-Bi with polyolefins and hemp fibres

Ternary composites of a biodegradable thermoplastic matrix, Mater-Bi® (MB), with various polyolefins (PP, HDPE and PS) and hemp fibres (H) were obtained by melt mixing and characterized by SEM, OM, DSC, TGA and tensile tests. The properties of composites were compared with those of MB/polyolefin and MB/H blends. Maleic anhydride functionalized polyolefins were employed as compatibilizers. Crystallization behaviour and morphology of the composites were found to be affected by the composition, phase dispersion and compatibilizer. Thermogravimetric analysis indicated that the thermal stability of the polyolefin phase and fibres was influenced by the composition and phase structure. A significant improvement of tensile modulus and strength was recorded for composites of MB with PE and PS as compared to MB/H composites. The results indicate that incorporation of polyolefins in the biodegradable matrix, compared to binary matrix/fibre system, may have significant advantages in terms of properties, processability and cost.     

Sustainable food packaging: Valorising wheat straw fibres for tuning PHBV-based composites properties

The present work aims at investigating the impact of wheat straw fibres (WSF) size, morphology and content on the process-ability and functional properties (mechanical properties and water vapour permeability) of PHBV-based composites. For that purpose, three types of fibres obtained by successive grindings (from the micrometric up to the millimetric scale) were used. It was shown that the highest possible filler level was all the more high when decreasing fibre size (over 50 wt% in the case of micrometric fibres), due to reduced film heterogeneity and improved fibre wetting by the polymer. As regards functional properties, increasing fibre size and/or content led to a significant degradation of ultimate tensile properties, while Young’s modulus was not significantly affected. At the same time, water vapour transmission rate was significantly increased from 11 up to 110 g m⁻² day⁻¹, which could extend the applicability of PHBV/WSF composites as food packaging materials to respiring fresh products.     

PLA/algae composites: Morphology and mechanical properties

Bio-composites with poly(lactic) acid as matrix and various algae (red, brown and green) as filler were prepared via melt mixing. Algae initial size (below 50 μm and between 200 and 400 μm) and concentration (from 2 to 40 wt%) were varied. First, algae morphology, composition and surface properties are analysed for each algae type. Second, an example of algae particle size decrease during processing is given. Finally, tensile properties of composites are analysed. The surface of algae flakes was covered with inorganic salts affecting filler–matrix interactions. The Young’s modulus of composites increased at 40 wt% load of algae as compared with neat PLA although the strain at break and tensile strength decreased. In most cases the influence of algae type was minor. Larger flakes led to better mechanical properties compared to the smaller ones.     

Review of the mechanical properties of carbon nanofiber/polymer composites

In this paper, the mechanical properties of vapor grown carbon nanofiber (VGCNF)/polymer composites are reviewed. The paper starts with the structural and intrinsic mechanical properties of VGCNFs. Then the major factors (filler dispersion and distribution, filler aspect ratio, adhesion and interface between filler and polymer matrix) affecting the mechanical properties of VGCNF/polymer composites are presented. After that, VGCNF/polymer composite mechanical properties are discussed in terms of nanofibers dispersion and alignment, adhesion between the nanofiber and polymer matrix, and other factors. The influence of processing methods and processing conditions on the properties of VGCNF/polymer composite is also considered. At the end, the possible future challenges for VGCNF and VGCNF/polymer composites are highlighted.     

Enhancement of fracture toughness,mechanical and thermal properties of rubber/epoxy composites by incorporation of graphene nanoplatelets

Carboxyl terminated butadiene acrylonitrile (CTBN) was added to epoxy resins to improve the fracture toughness, and then two different lateral dimensions of graphene nanoplatelets (GnPs), nominally <1 μm (GnP-C750) and 5 μm (GnP-5) in diameter, were individually incorporated into the CTBN/epoxy to fabricate multi-phase composites. The study showed that GnP-5 is more favorable for enhancing the properties of CTBN/epoxy. GnPs/CTBN/epoxy ternary composites with significant toughness and thermal conductivity enhancements combined with comparable stiffness to that of the neat resin were successfully achieved by incorporating 3 wt.% GnP-5 into 10 wt.% CTBN modified epoxy resins. According to the SEM investigations, GnP-5 debonding from the matrix is suppressed due to the presence of CTBN. Nevertheless, apart from rubber cavitation and matrix shear banding, additional active toughening mechanisms induced by GnP-5, such as crack deflection, layer breakage and separation/delamination of GnP-5 layers contributed to the enhanced fracture toughness of the hybrid composites.     

Effect of linear density and yarn structure on the mechanical properties of ramie fiber yarn reinforced composites

Effects of linear density and yarn structure on both static and dynamic mechanical properties of ramie fiber yarn reinforced composites (RYRCs) were investigated. The failure mechanisms of RYRCs were analyzed with the aid of ultrasonic C-scan and Scanning electronic microscopy (SEM). The results showed that the tensile strength of RYRCs increased gradually with increase of the linear density of the single yarns. The maximum tensile strength was obtained when the linear density reached 67.3 tex. However, a downtrend of the tensile strength was observed with further increase of the linear density of ramie single and plied yarns. The interlaminar fracture toughness was relatively high for RYRCs made from yarns with lower linear density due to the extensive fiber bridging observed during the double cantilever beam test. Meanwhile, the linear density and structure of ramie yarn had remarkable influence on the failure mode of RYRCs during the drop weight impact test.     

Thermal and mechanical properties of phenolic-based composites reinforced by carbon fibres and multiwall carbon nanotubes

The thermal, mechanical and ablation properties of carbon fibre/phenolic composites filled with multiwall carbon nanotubes (MWCNTs) were investigated. Carbon fibre/phenolic/MWCNTs were prepared using different weight percentage of MWCNTs by compression moulding. The samples were characterized by scanning electron microscopy (SEM), flexural tests, thermal gravimetric analysis and oxyacetylene torch tests. The thermal stability and flexural properties of the nanocomposites increased by increasing MWCNTs content (wt% ⩽1), but they decreased when the content of MWCNTs was 2 wt%. The linear and mass ablation rates of the nanocomposites after modified with 1 wt% MWCNTs decreased by about 80% and 52%, respectively. To investigate the material post-test microstructure, a morphological characterization was carried out using SEM. It was shown that the presence of MWCNTs in the composite led to the formation of a strong network char layer without any cracks or opening.     

Effect of hydrothermal pretreatment on the properties of moso bamboo particles reinforced polyvinyl chloride composites

Bamboo plastic composites were fabricated from polyvinyl chloride (PVC) and moso bamboo particles (BP). In order to improve the interfacial interaction between BP and PVC, as well as to obtain composites with outstanding mechanical properties, the roles of hydrothermal treating temperatures (120, 140, 160, 180, 200, 220, 240, 260 and 280 °C) on characteristics of BP and properties of the PVC/BP composites were investigated. Results showed that hydrothermal modification improved the surface property of BP and wiped off hemicelluloses and pectin. A uniform dispersion of BP in PVC matrix was observed by SEM with hydrothermal treatment. Tensile strength, tensile modulus and flexural strength of the composites achieved their maximal values of 15.79 MPa, 6702.26 MPa and 39.57 MPa, respectively, with 180 °C hydrothermal treatment. The highest values of elongation at break and flexural deformation were 3.75 ± 0.20% with 200 °C hydrothermal modification and 36.22 ± 2.70% with 140 °C hydrothermal modification, respectively. Due to more decomposition of hemicellulose, the composites expressed lower water absorption and higher thermal stability when the hydrothermal treating temperature exceed 160 °C.     

Flexural properties of hemp fibre reinforced polylactide and unsaturated polyester composites

In this work, flexural strength and flexural modulus of chemically treated random short and aligned long hemp fibre reinforced polylactide and unsaturated polyester composites were investigated over a range of fibre content (0-50 wt%). Flexural strength of the composites was found to decrease with increased fibre content; however, flexural modulus increased with increased fibre content. The reason for this decrease in flexural strength was found to be due to fibre defects (i.e. kinks) which could induce stress concentration points in the composites during flexural test, accordingly flexural strength decreased. Alkali and silane fibre treatments were found to improve flexural strength and flexural modulus which could be due to enhanced fibre/matrix adhesion.     

Effect of ZnO nanoparticles doped graphene on static and dynamic mechanical properties of natural rubber composites

In this work, effect of ZnO nanoparticles doped graphene (Nano-ZnO–GE) on static and dynamic mechanical properties of natural rubber composites were studied. Nano-ZnO–GE was synthesized by sol–gel method and thermal treatment. With the incorporation of nano-ZnO–GE into the matrix, the mechanical properties of NR nanocomposite significantly improved over that of NR composite containing with 5 phr of conventional-ZnO. The results demonstrated that the presence of nano-ZnO on the surface of graphene sheets not only conduces to suppressing aggregation of graphene sheets but also acts as a more efficient cure-activator in vulcanization process, with the formation of excellent crosslinked network at low nano-ZnO–GE content. This work also showed that NR/Nano-ZnO–GE nanocomposites exhibited higher wet grip property and lower rolling resistance compared with NR/Conventional-ZnO composite, which makes nano-ZnO–GE very competitive for the green tire application as a substitute of conventional-ZnO, enlarging versatile practical application to prepare high-performance rubber nanocomposites.     

Effect of shearing on the orientation, crystallization and mechanical properties of HDPE/attapulgite nanocomposites

High density polyethylene (HDPE)/attapulgite (AT) nanocomposites, prepared by conventional injection molding (CIM) and dynamic packing injection molding (DPIM), were investigated with focus on AT-induced crystallization and orientation under shear. Infrared spectroscopy (FTIR) analysis showed there is no special chemical interaction between HDPE and AT, but shear induced significant changes on the material structure and properties. Differential scanning calorimetry (DSC) analysis showed strong nucleation effect by AT especially under shear. And more, shear will induce much better dispersion of AT in the DPIM sample vs. CIM. AT nanorods and lamellae of HDPE are more organized in the DPIM sample while there is only random distribution in the CIM sample. Most AT nanorods embed in the HDPE lamellae and form a brush-like hybrid structure due to shear. The shear-induced orientation will be enhanced with higher AT loading. The mechanical performance of the composites was significantly improved via DPIM.     

Mechanical properties of epoxy composites filled with silane-functionalized graphene oxide

In this work, the effects of as-produced GO and silane functionalized GO (silane-f-GO) loading and silane functionalization on the mechanical properties of epoxy composites are investigated and compared. Such silane functionalization containing epoxy ended-groups is found to effectively improve the compatibility between the silane-f-GO and the epoxy matrix. Increased storage modulus, glass transition temperature, thermal stability, tensile and flexural properties and fracture toughness of epoxy composites filled with the silane-f-GO sheets are observed compared with those of the neat epoxy and GO/epoxy composites. These findings confirm the improved dispersion and interfacial interaction in the composites arising from covalent bonds between the silane-f-GO and the epoxy matrix. Moreover, several possible fracture mechanisms, i.e. crack pinning/deflection, crack bridging, and matrix plastic deformation initiated by the debonding/delamination of GO sheets, were identified and evaluated.     

The compressive properties of expandable microspheres/epoxy foams

Expandable microspheres/epoxy foams with different densities and microstructures were prepared by changing the foaming temperature and the precuring extent. The microstructure of foams reveals a homogeneous distribution of cells at high precuring extent and high foaming temperature, while small cells size at high precuring extent and low foaming temperature. Furthermore, the compressive properties of epoxy foams were investigated. The compressive strength and modulus of the foam exhibited a power-law dependence with respect to density. By optimizing the foaming temperature and the precuring extent, epoxy foams with homogeneous cells and stable compressive property can be obtained. Fracture surface showed that deformed microspheres and less debris were observed at relatively high-density foams.     

Mechanical properties of epoxy composites with high contents of nanodiamond

Mechanical properties and thermal conductivity of composites made of nanodiamond with epoxy polymer binder have been studied in a wide range of nanodiamond concentrations (0-25 vol.%). In contrast to composites with a low content of nanodiamond, where only small to moderate improvements in mechanical properties were reported before, the composites with 25 vol.% nanodiamond showed an unprecedented increase in Young’s modulus (up to 470%) and hardness (up to 300%) as compared to neat epoxy. A significant increase in scratch resistance and thermal conductivity of the composites were observed as well. The improved thermal conductivity of the composites with high contents of nanodiamond is explained by direct contacts between single diamond nanoparticles forming an interconnected network held together by a polymer binder.     

Effect of mechanical activation pretreatment on the properties of sugarcane bagasse/poly(vinyl chloride) composites

This current work is concerned with the pretreatment of sugarcane bagasse (SCB) by mechanical activation (MA) using a self-designed stirring ball mill and surface modification of SCB using aluminate coupling agent (ACA). The untreated and differently treated SCBs were used to produce composites with poly(vinyl chloride) (PVC) as polymer matrix. The activation grade (A_g) measurement and Fourier transform infrared (FTIR) analysis of SCB showed that MA enhanced the condensation reaction between ACA and hydroxyl groups of the SCB fibres, which obviously increased the hydrophobicity of SCB. It was found that the mechanical properties of both the PVC composites reinforced by SCB with and without ACA modification increased with increasing milling time (t_M). Scanning electron microscopy (SEM) analysis showed that MA pretreatment significantly improved the dispersion of SCB in the composites and interfacial adhesion between SCB and PVC matrix, resulting in better mechanical properties of the composites.     

Influence of moisture uptake on the static,cyclic and dynamic behaviour of unidirectional flax fibre-reinforced epoxy laminates

This papers aims to characterize the influence of moisture uptake on the mechanical behaviour of unidirectional flax fibre-reinforced epoxy laminates. Monotonic and cyclic tensile tests and free vibration characterization are carried out. Results show that UD flax-epoxy composites, when exposed to hygrothermal conditioning at 70 °C and 85% RH, exhibit a diffusion kinetic which follows a one dimensional Fickian behaviour. The mass uptake at equilibrium is approximately 3.3% and the diffusion coefficient 6.5 × 10⁻⁶ m² s⁻¹. Water vapour sorption is shown to induce a significant change in the shape of the tensile stress-strain curve, a decrease in the dynamic elastic modulus of about 20% and a 50% increase in the damping ratio. Contrary to all expectations, water saturation does not degrade the monotonic tensile strength of such a flax-epoxy composites and leads to an increase in the fatigue strength for a high number of cycles.